Characterization cement pastes degraded in lanoratory solutions and physiochemical parameters employed for modeling the process

Previously degradation studies carried out, over a number of different mortars by the research team, have shown that observed degradation does not exclusively depend on the solution equilibrium pH, nor the aggressive anions relative solubility. In our tests no reason was found that could allow us to explain, why same solubility anions with a lower pH are less aggressive than others. The aim of this paper is to study cement pastes behavior in aggressive environments. As observed in previous research, this cement pastes behaviors are not easily explained only taking into account only usual parameters, pH, solubility etc. Consequently the paper is about studying if solution physicochemical characteristics are more important in certain environments than specific pH values. The paper tries to obtain a degradation model, which starting from solution physicochemical parameters allows us to interpret the different behaviors shown by different composition cements. To that end, the rates of degradation of the solid phases were computed for each considered environment. Three cement have been studied: CEM I 42.5R/SR, CEM II/A-V 42.5R and CEM IV/B-(P-V) 32.5 N. The pastes have been exposed to five environments: sodium acetate/acetic acid 0.35 M, sodium sulfate solution 0.17 M, a solution representing natural water, saturated calcium hydroxide solution and laboratory environment. The attack mechanism was meant to be unidirectional, in order to achieve so; all sides of cylinders were sealed except from the attacked surface. The cylinders were taking out of the exposition environments after 2, 4, 7, 14, 30, 58 and 90 days. Both aggressive solution variations in solid phases and in different depths have been characterized. To each age and depth the calcium, magnesium and iron contents have been analyzed. Hydrated phases evolution studied, using thermal analysis, and crystalline compound changes, using X ray diffraction have been also analyzed. Sodium sulphate and water solutions stabilize an outer pH near to 8 in short time, however the stability of the most pH dependent phases is not the same. Although having similar pH and existing the possibility of forming a plaster layer near to the calcium leaching surface, this stability is greater than other sulphate solutions. Stability variations of solids formed by inverse diffusion, determine the rate of degradation.

Transcriptional changes and oxidative stress associated with the synergistic interaction between potato virus X and potato virus Y and their relationship with symptom expression.

Many virus diseases of economic importance to agriculture result from mixtures of different pathogens invading the host at a given time. This contrasts with the relatively scarce studies available on the molecular events associated with virus---host interactions in mixed infections. Compared with single infections, co-infection of Nicotiana benthamiana with Potato virus X (PVX) and Potato virus Y (PVY) resulted in increased systemic symptoms (synergism) that led to necrosis of the newly emerging leaves and death of the plant. A comparative transcriptional analysis was undertaken to identify quantitative and qualitative differences in gene expression during this synergistic infection and correlate these changes with the severe symptoms it caused. Global transcription profiles of doubly infected leaves were compared with those from singly infected leaves using gene ontology enrichment analysis and metabolic pathway annotator software. Functional gene categories altered by the double infection comprise suites of genes regulated coordinately, which are associated with chloroplast functions (downregulated), protein synthesis and degradation (upregulated), carbohydrate metabolism (upregulated), and response to biotic stimulus and stress (upregulated). The expressions of reactive oxygen species?generating enzymes as well as several mitogen-activated protein kinases were also significantly induced. Accordingly, synergistic infection induced a severe oxidative stress in N. benthamiana leaves, as judged by increases in lipid peroxidation and by the generation of superoxide radicals in chloroplasts, which correlated with the misregulation of antioxidative genes in microarray data. Interestingly, expression of genes encoding oxylipin biosynthesis was uniquely upregulated by the synergistic infection. Virus-induced gene silencing of ?-dioxygenase1 delayed cell death during PVX?PVY infection.

Metabolomics demonstrates divergent responses of two Eucalyptus species to water stress

Past studies of water stress in Eucalyptus spp. generally highlighted the role of fewer than five “important” metabolites, whereas recent metabolomic studies on other genera have shown tens of compounds are affected. There are currently no metabolite profiling data for responses of stress-tolerant species to water stress. We used GC–MS metabolite profiling to examine the response of leaf metabolites to a long (2 month) and severe (Ψpredawn < −2 MPa) water stress in two species of the perennial tree genus Eucalyptus (the mesic Eucalyptus pauciflora and the semi-arid Eucalyptus dumosa). Polar metabolites in leaves were analysed by GC–MS and inorganic ions by capillary electrophoresis. Pressure–volume curves and metabolite measurements showed that water stress led to more negative osmotic potential and increased total osmotically active solutes in leaves of both species. Water stress affected around 30–40% of measured metabolites in E. dumosa and 10–15% in E. pauciflora. There were many metabolites that were affected in E. dumosa but not E. pauciflora, and some that had opposite responses in the two species. For example, in E. dumosa there were increases in five acyclic sugar alcohols and four low-abundance carbohydrates that were unaffected by water stress in E. pauciflora. Re-watering increased osmotic potential and decreased total osmotically active solutes in E. pauciflora, whereas in E. dumosa re-watering led to further decreases in osmotic potential and increases in total osmotically active solutes. This experiment has added several extra dimensions to previous targeted analyses of water stress responses in Eucalyptus, and highlights that even species that are closely related (e.g. congeners) may respond differently to water stress and re-watering

Optimization of InGaAsN(Sb)/GaAs quantum dots for optical emission at 1.55 µm with low optical degradation

Low optical degradation in GaInAsN(Sb)/GaAs quantum dots (QDs) p–i–n structures emitting up to 1.55 μm is presented in this paper. We obtain emission at different energies by means of varying N content from 1 to 4%. The samples show a low photoluminescence (PL) intensity degradation of only 1 order of magnitude when they are compared with pure InGaAs QD structures, even for an emission wavelength as large as 1.55 μm. The optimization studies of these structures for emission at 1.55 μm are reported in this work. High surface density and homogeneity in the QD layers are achieved for 50% In content by rapid decrease in the growth temperature after the formation of the nanostructures. Besides, the effect of N and Sb incorporation in the redshift and PL intensity of the samples is studied by post-growth rapid thermal annealing treatments. As a general conclusion, we observe that the addition of Sb to QD with low N mole fraction is more efficient to reach 1.55 μm and high PL intensity than using high N incorporation in the QD. Also, the growth temperature is determined to be an important parameter to obtain good emission characteristics. Finally, we report room temperature PL emission of InGaAsN(Sb)/GaAs at 1.4 μm.

Study of the evolution of the seismic cycle of stress and strain associated to the El Salvador Fault Zone

• Central America: – Regional studies in Central America (Seismic Hazard). – El Salvador Fault Zone (ESFZ). – Aguacaliente‐Navarro Fault Zone (ANFZ), Central Valley of Costa Rica. – Haiti (seismic hazard) • Spain: – Regional‐Nacional studies of seismic hazards (applications to building codes, eurocode, emergency plans, etc.) – Betic range zone, south of Spain. – Ibero‐Maghrebi region (collision zone)

Caracterización de los parámetros de resistencia al corte y erosionabilidad del suelo para su aplicación en los problemas de estabilidad de taludes en obras lineales

La tesis se organiza en un volumen de Memoria integrada por once capítulos que constituyen el cuerpo de la tesis y otro volumen de Apéndices titulado “Caracterización geotécnica de Base de los suelos de España” que reúne en forma de cuadros las características de textura, permeabilidad, humedad-succión, erosionabilidad y resistencia al corte de los cuarenta y dos perfiles de suelos representativos de los tipos del Mapa de suelos De España. Estos cuadros han sido elaborados originalmente por la doctorando durante sus estudios para la obtención del DEA de la Suficiencia Investigadora, excepto los de resistencia al corte que lo han sido también por la doctorando de forma original, pero ya en la etapa de redacción de la tesis. En el Capítulo 1 “Introducción” se describe la motivación, antecedentes, alcance y contenido de la tesis, ordenado según el índice que en él se incluye. Los Capítulos 2 “Meteorización, 3 “Balance Hídrico” y 4 “Humedades características” constituyen el “estado del arte” en el momento actual de los temas de geotecnia ambiental relacionados con la degradación de la superficie terrestre y la estabilidad de taludes. El Capítulo 2, tras matizar algunas generalidades, aporta elementos para la cuantificación de la alteración de rocas como el “índice climático de Weinert” y de la erosión de suelos como la “ecuación universal de pérdida de suelo (U.S.L.E.)” El Capítulo 3, partiendo de los fenómenos de precipitación y evapotranspiración, plantea el balance hídrico en vertientes con instrumentos para evaluar la infiltración y la escorrentía, conceptos imprescindibles para adentrarse en los de resistencia y erosionabilidad del conjunto suelo-agua. En los Apéndices A1 y A2, se recogen valores de coeficientes de infiltración en condiciones saturadas y no saturadas de los perfiles de suelos del Mapa de España. El Capítulo 4 se dedica al estudio de este conjunto suelo-agua con la definición de conceptos que lo caracterizan, basados en la relación entre los contenidos de ambos elementos o “humedad”, sus valores máximos y mínimos y la forma en la que es retenida el agua por el suelo. Este capítulo acaba con el concepto de “Curva característica Suelo-Agua/Soil Water Characteristic curve (SWCC)”, que liga el contenido de agua de un suelo con la tensión a la que está retenida (uauw) “succión” o con su expresión más usual “pF”. En el Apéndice A 3 se adjuntan las SWCC de los perfiles de suelos del Mapa de suelos de España. En el Capítulo 5 “Resistencia al corte de los suelos”, se detalla la influencia que tienen sobre la resistencia de los suelos factores como el paso del tiempo, el contenido de humedad y la presencia y tipo de vegetación en la superficie del suelo estudiado. El Capítulo 6 “Evaluación de la erosión”, analiza el factor de erosionabilidad del suelo “factor K” de la U.S.L.E., su evaluación en función de la textura, estructura y permeabilidad del suelo, con la estimación hecha para los cuarenta y dos perfiles de suelos del Mapa de España, contenida en el Apéndice 4. En el Capítulo 7 “Metodología de diseño” se hacen en su primera parte unas consideraciones geoambientales de diseño aplicables al estudio de los problemas de inestabilidades en taludes. La segunda parte constituye el núcleo de la tesis con la propuesta de “estimación de los parámetros de resistencia al corte del suelo”, consecuente con las teorías y metodología de análisis expuesta en los capítulos anteriores. En el Apéndice A 5 se presentan los valores de los parámetros coulombianos de resistencia al corte, ”c y Ф” estimados según la caracterización climática a partir del índice de Thornthwaite, en condicionesde diseño para humedades naturales máxima y mínima de los cuarenta y dos perfiles de suelos del Mapa de suelos de España. El Capítulo 8 “Aplicación a casos reales” se considera de gran interés al constituir una auténtica continuación de la segunda parte del capítulo anterior, desarrollando la metodología expuesta en él a cuatro problemáticas de infraestructuras de obras lineales, relacionadas con problemas de erosión y deslizamientos en taludes. El Capítulo 9 “Ensayos de referencia” se incluye como punto de apoyo (referencia) a las teorías expuestas, valorando la idoneidad de los tipos de ensayos y tipos de suelos seleccionados (Laboratorio de Geotecnia del CEDEX y Laboratorio Hong-Kong University of Science and Technology), utilizados para la obtención, por correlaciones deducidas, de las curvas SWCC de los perfiles de suelos del Mapa de España, incluídas en el Apéndice A 3, como se ha citado antes. En el Capítulo 10 “Conclusiones y Futuras Líneas de Investigación”se apuntan en primer lugar unas conclusiones que, a juicio de la doctorando, se pueden extraer con interés de esta tesis y a continuación se esbozan unas posibles líneas de investigación, fundamentalmente de tipo experimental, que complementarían los avances derivados de esta tesis o podrían esclarecer y abrir nuevas interpretaciones de los fenómenos naturales de erosión y estabilidad de taludes en los que ésta se ha centrado. Finalmente, en el Capítulo 11 “Bibliografía” se han reunido 328 referencias que reflejan una visión amplia y bastante completa del tema tratado, obtenida complementando las de tesis anteriores sobre esta singular materia (“Efecto estabilizador de la vegetación en taludes”, L Fort 1975 y “Determinación de las características de fricción en el contacto suelo-geotextil a diferentes succiones, mediante equipos de laboratorio singulares”, E Asanza 2009), con propias de la doctorando (9) y las consideradas de mayor interés de los últimos Congresos sobre Suelos no saturados,”Unsat 95”, “Unsat 2002” y “Unsat 2011” entre otros. ABSTRACT The thesis is organized in a volume of Memory composed of eleven chapters that make up the body of the thesis and other Appendices volume entitled "Geotechnical characterization of basis of the soils of Spain" that combines the characteristics of texture, permeability, moisture-suction, erosionability, and shear strength of forty-two profiles of soils representative of the types of the soil of Spain map in the form of pictures. These pictures have been produced originally by the student during their studies to obtain the DEA of the research, except those of the shear strength, also been done by the PhD student in an original way, but already at the stage of drafting of the thesis. Chapter 1 "Introducción" describes the motivation, background, scope and content of the thesis, ordered according to the index that is included. The Chapters: 2 "Weathering, 3 “Water Balance” and 4 “moisture characteristics" are the "State of the art" at the present time of geotechnical environmental issues related to the degradation of the Earth's surface and the slope stability. Chapter 2 after clarify some general information, provides elements for the quantification of the alteration of rocks as "Weinert climate index" and soil erosion as the "universal equation of loss of soil (U.S.L.E.)" Chapter 3, on the basis of the phenomena of precipitation and evapotranspiration, raises the water balance in sheds with instruments to evaluate infiltration and runoff, essential concepts into the resistance and erosionability water-soil joint. Values of soils coefficients of infiltration in saturated and unsaturated conditions from the Spain map of profiles are collected in the Appendices A1 and A2. Chapter 4 is dedicated to the study of this joint “soil-water”, with the definition of concepts that characterize it, based on the relationship between the contents of both elements or “moisture”, their maximum and minimum values and the way in which water is retained by the soil. This chapter ends with the concept of “Soil Water Characteristic curve (SWCC)", which linked the water content of a soil with the stress that it is retained (ua-uw) "suction" or its expression more usual "pF". The SWCC of the profiles of soils of the Spain soils Map are attached in the Appendix 3. In Chapter 5 “Soils shear strength”,is detailed the influence that they have on the resistance of soils factors such as the passage of time, the content of moisture and the presence and type of vegetation on the surface of the studied soil. Chapter 6 "Assessment of erosion", analyses the soil erodibility factor "Kfactor" of the U.S.L.E., its evaluation based on texture, structure and permeability of the soil, with the estimate for forty-two profiles of soils on the Spain Soils Map, contained in Appendix 4. Chapter 7 "Design methodology" some considerations are made in the first part geo-environmental design applicable to the study of the problems of instabilities in slopes. The second part constitutes the core of the thesis with the proposal of “estimation of parameters of shear strength”, of the soils consistent with theories and analytical methodology outlined in the previous chapters. Appendix A 5 presents the values of the coulombians parameters of shear strength, "c and Ф" according to the characterization of climate from the index of Thornthwaite, in design for natural moisture conditions maximum and minimum of forty-two profils of Spain Soils Map Chapter 8 "Application to real cases" is considered of great interest to constitute a true continuation of the second part of the previous chapter, developing the methodology exposed it to four problems of civil-works infrastructure, related to problems of erosion and landslides in slopes. Chapter 9 "Tests of reference" is included as point of support (reference) to the theories exposed, assessing the suitability of the types of tests and types of selected soils (Geotechnical laboratory of CEDEX and laboratory Hongkong University of Science and Technology), used to obtain, by deduced correlations, of curves SWCC of soils profiles on the Spain Soils Map, included in Appendix A. 3, as it was mentioned before. Chapter 10 "Conclusions and future research lines" are running first conclusions which, in the opinion of the candidate, can be extracted with interest of this thesis, and then, it outlines some possible lines of research, mainly experimental, which would complement the advances arising from this thesis or could clarify and open new interpretations of natural phenomena of erosion and slope stability in which it has focused. Finally, in Chapter 11 "Bibliography" 328 references have been included which reflect a broad and fairly comprehensive view of the subject matter, obtained complementing those of the previous theses on this singular issue ("Vegetation stabilizing effect on slopes", L Fort 1975, and "Determination of the characteristics of friction in the contact soil-geotextile to different-suctions, through special laboratory equipment", E Asanza 2009) with some of them from of the candidate (9) and the others from of the considered as the most interesting of recent conferences on unsaturated soils, "Unsat 95", "Unsat2002" and "Unsat 2011" among others.

Observed degradation in photovoltaic plants affected by hot-spots

A number of findings have shown that the test procedures currently available to determine the reliability and durability of photovoltaic (PV) modules are insufficient to detect certain problems. To improve these procedures, ongoing research into the actual performance of the modules in the field is required. However, scientific literature contains but few references to field studies of defective modules. This article studies two different localized heating phenomena affecting the PV modules of two large-scale PV plants in Spain. The first problem relates to weak solder joints whilst the second is due to microcracks on the module cells. For both cases, the cause is identified, and consideration is given with regard to the effect on performance, the potential deterioration over time, and a way to detect the problems identified. The findings contained in this paper will prove to be of considerable interest to maintenance personnel at large-scale PV plants and also to those responsible for setting module quality standards and specifications, and even the PV module manufacturers themselves.

Cycling Dof Factors: Molecular and functional characterization of Arabidopsis thaliana AtCDF3 and tomato (Solanum lycopersicum L.) SlCDF3 in response to abiotic stress

El tomate (Solanum lycopersicum L.) es considerado uno de los cultivos hortícolas de mayor importancia económica en el territorio Español. Sin embargo, su producción está seriamente afectada por condiciones ambientales adversas como, salinidad, sequía y temperaturas extremas. Para resolver los problemas que se presentan en condiciones de estrés, se han empleado una serie de técnicas culturales que disminuyen sus efectos negativos, siendo de gran interés el desarrollo de variedades tolerantes. En este sentido la obtención y análisis de plantas transgénicas, ha supuesto un avance tecnológico, que ha facilitado el estudio y la evaluación de genes seleccionados en relación con la tolerancia al estrés. Estudios recientes han mostrado que el uso de genes reguladores como factores de transcripción (FTs) es una gran herramienta para obtener nuevas variedades de tomate con mayor tolerancia a estreses abióticos. Las proteínas DOF (DNA binding with One Finger) son una familia de FTs específica de plantas (Yangisawa, 2002), que están involucrados en procesos fisiológicos exclusivos de plantas como: asimilación del nitrógeno y fijación del carbono fotosintético, germinación de semilla, metabolismo secundario y respuesta al fotoperiodo pero su preciso rol en la tolerancia a estrés abiótico se desconoce en gran parte. El trabajo descrito en esta tesis tiene como objetivo estudiar genes reguladores tipo DOF para incrementar la tolerancia a estrés abiotico tanto en especies modelo como en tomate. En el primer capítulo de esta tesis se muestra la caracterización funcional del gen CDF3 de Arabidopsis, así como su papel en la respuesta a estrés abiótico y otros procesos del desarrollo. La expresión del gen AtCDF3 es altamente inducido por sequía, temperaturas extremas, salinidad y tratamientos con ácido abscísico (ABA). La línea de inserción T-DNA cdf3-1 es más sensible al estrés por sequía y bajas temperaturas, mientras que líneas transgénicas de Arabidopsis 35S::AtCDF3 aumentan la tolerancia al estrés por sequía, osmótico y bajas temperaturas en comparación con plantas wild-type (WT). Además, estas plantas presentan un incremento en la tasa fotosintética y apertura estomática. El gen AtCDF3 se localiza en el núcleo y que muestran una unión específica al ADN con diferente afinidad a secuencias diana y presentan diversas capacidades de activación transcripcional en ensayos de protoplastos de Arabidopsis. El dominio C-terminal de AtCDF3 es esencial para esta localización y su capacidad activación, la delección de este dominio reduce la tolerancia a sequía en plantas transgénicas 35S::AtCDF3. Análisis por microarray revelan que el AtCDF3 regula un set de genes involucrados en el metabolismo del carbono y nitrógeno. Nuestros resultados demuestran que el gen AtCDF3 juega un doble papel en la regulación de la respuesta a estrés por sequía y bajas temperaturas y en el control del tiempo de floración. En el segundo capítulo de este trabajo se lleva a cabo la identificación de 34 genes Dof en tomate que se pueden clasificar en base a homología de secuencia en cuatro grupos A-D, similares a los descritos en Arabidopsis. Dentro del grupo D se han identificado cinco genes DOF que presentan características similares a los Cycling Dof Factors (CDFs) de Arabidopsis. Estos genes son considerados ortólogos de Arabidopsis CDF1-5, y han sido nombrados como Solanum lycopersicum CDFs o SlCDFs. Los SlCDF1-5 son proteínas nucleares que muestran una unión específica al ADN con diferente afinidad a secuencias diana y presentan diversas capacidades de activación transcripcional in vivo. Análisis de expresión de los genes SlCDF1-5 muestran diferentes patrones de expresión durante el día y son inducidos de forma diferente en respuesta a estrés osmótico, salino, y de altas y bajas temperaturas. Plantas de Arabidopsis que sobre-expresan SlCDF1 y SlCDF3 muestran un incremento de la tolerancia a la sequía y salinidad. Además, de la expresión de varios genes de respuesta estrés como AtCOR15, AtRD29A y AtERD10, son expresados de forma diferente en estas líneas. La sobre-expresión de SlCDF3 en Arabidopsis promueve un retardo en el tiempo de floración a través de la modulación de la expresión de genes que controlan la floración como CONSTANS (CO) y FLOWERING LOCUS T (FT). En general, nuestros datos demuestran que los SlCDFs están asociados a funciones aun no descritas, relacionadas con la tolerancia a estrés abiótico y el control del tiempo de floración a través de la regulación de genes específicos y a un aumento de metabolitos particulares. ABSTRACT Tomato (Solanum lycopersicum L.) is one of the horticultural crops of major economic importance in the Spanish territory. However, its production is being affected by adverse environmental conditions such as salinity, drought and extreme temperatures. To resolve the problems triggered by stress conditions, a number of agricultural techniques that reduce the negative effects of stress are being frequently applied. However, the development of stress tolerant varieties is of a great interest. In this direction, the technological progress in obtaining and analysis of transgenic plants facilitated the study and evaluation of selected genes in relation to stress tolerance. Recent studies have shown that a use of regulatory genes such as transcription factors (TFs) is a great tool to obtain new tomato varieties with greater tolerance to abiotic stresses. The DOF (DNA binding with One Finger) proteins form a family of plant-specific TFs (Yangisawa, 2002) that are involved in the regulation of particular plant processes such as nitrogen assimilation, photosynthetic carbon fixation, seed germination, secondary metabolism and flowering time bur their precise roles in abiotic stress tolerance are largely unknown. The work described in this thesis aims at the study of the DOF type regulatory genes to increase tolerance to abiotic stress in both model species and the tomato. In the first chapter of this thesis, we present molecular characterization of the Arabidopsis CDF3 gene as well as its role in the response to abiotic stress and in other developmental processes. AtCDF3 is highly induced by drought, extreme temperatures, salt and abscisic acid (ABA) treatments. The cdf3-1 T-DNA insertion mutant was more sensitive to drought and low temperature stresses, whereas the AtCDF3 overexpression enhanced the tolerance of transgenic plants to drought, cold and osmotic stress comparing to the wild-type (WT) plants. In addition, these plants exhibit increased photosynthesis rates and stomatal aperture. AtCDF3 is localized in the nuclear region, displays specific binding to the canonical DNA target sequences and has a transcriptional activation activity in Arabidopsis protoplast assays. In addition, the C-terminal domain of AtCDF3 is essential for its localization and activation capabilities and the deletion of this domain significantly reduces the tolerance to drought in transgenic 35S::AtCDF3 overexpressing plants. Microarray analysis revealed that AtCDF3 regulated a set of genes involved in nitrogen and carbon metabolism. Our results demonstrate that AtCDF3 plays dual roles in regulating plant responses to drought and low temperature stress and in control of flowering time in vegetative tissues. In the second chapter this work, we carried out to identification of 34 tomato DOF genes that were classified by sequence similarity into four groups A-D, similar to the situation in Arabidopsis. In the D group we have identified five DOF genes that show similar characteristics to the Cycling Dof Factors (CDFs) of Arabidopsis. These genes were considered orthologous to the Arabidopsis CDF1 - 5 and were named Solanum lycopersicum CDFs or SlCDFs. SlCDF1-5 are nuclear proteins that display specific binding to canonical DNA target sequences and have transcriptional activation capacities in vivo. Expression analysis of SlCDF1-5 genes showed distinct diurnal expression patterns and were differentially induced in response to osmotic, salt and low and high temperature stresses. Arabidopsis plants overexpressing SlCDF1 and SlCDF3 showed increased drought and salt tolerance. In addition, various stress-responsive genes, such as AtCOR15, AtRD29A and AtERD10, were expressed differently in these lines. The overexpression of SlCDF3 in Arabidopsis also results in the late flowering phenotype through the modulation of the expression of flowering control genes such CONSTANS (CO) and FLOWERING LOCUS T (FT). Overall, our data connet SlCDFs to undescribed functions related to abiotic stress tolerance and flowering time through the regulation of specific target genes and an increase in particular metabolites.

Implications of the mesophyll conductance to CO2 for photosynthesis and water-use efficiency during long-term water stress and recovery in two contrasting Eucalyptu species

Water stress (WS) slows growth and photosynthesis (An), but most knowledge comes from short-time studies that do not account for longer term acclimation processes that are especially relevant in tree species. Using two Eucalyptus species that contrast in drought tolerance, we induced moderate and severe water deficits by withholding water until stomatal conductance (gsw) decreased to two pre-defined values for 24 d, WS was maintained at the target gsw for 29 d and then plants were re-watered. Additionally, we developed new equations to simulate the effect on mesophyll conductance (gm) of accounting for the resistance to refixation of CO2. The diffusive limitations to CO2, dominated by the stomata, were the most important constraints to An. Full recovery of An was reached after re-watering, characterized by quick recovery of gm and even higher biochemical capacity, in contrast to the slower recovery of gsw. The acclimation to long-term WS led to decreased mesophyll and biochemical limitations, in contrast to studies in which stress was imposed more rapidly. Finally, we provide evidence that higher gm under WS contributes to higher intrinsic water-use efficiency (iWUE) and reduces the leaf oxidative stress, highlighting the importance of gm as a target for breeding/genetic engineering.

Induced thermo-mechanical stress in CPV receivers with cycled high intensity light

CPV receivers are made of materials with very different lineal expansion coefficients. Strong variations in DNI due to the passage of clouds can cause sudden temperature changes that creates mechanical stress. For common solder and metal filled polymers the plastic limit could be reached causing substantial fatigue. The best forecast of receiver reliability is therefore achieved by applying an intermittent light source with nominal irradiance level and a number of cycles equal to the expected cloud passages for a given site. The UPM has developed specialized equipment, dubbed the LYSS (Light cYcling Stressing Source), for carrying out such experiments. The small thermal capacity of receivers allows simulating more than 25000 cycles per week. The number of deep transients expected for Madrid in 30 years operation, based on available data, is about 45000. We are currently using the system to cycle a ?Ge/Ag Epoxy/aluminum? receiver, which shows no degradation after 20000 cycles. The equipment can cast up to 200 and 70 W/cm2 on 0.1 and 1 cm2 cells, respectively.

Respuesta transcripcional de Populus a bifenilos policlorados: Aspectos aplicados a la fitorremediación

La degradación del suelo ha adquirido una magnitud preocupante. Los métodos tradicionales de descontaminación, son costosos e insuficientes. La fitorremediación representa una alternativa eficaz, de bajo coste, respetuosa con el medio ambiente, que además mejora las propiedades del suelo, si bien ha habido desarrollos relevantes en la última década. Desde el punto de vida científico, el reto principal es descifrar las rutas metabólicas implicadas en respuesta a contaminantes y comprender su regulación. Esta información es imprescindible si aspiramos a mejorar las capacidades naturales de algunas especies vegetales para remediar los suelos contaminados. Los estudios de esta Tesis se han centrado en Populus, el mejor modelo forestal disponible a raíz de la secuenciación de su genoma completo. Por otra parte, Populus tiene una gran capacidad natural para la degradación de contaminantes orgánicos, lo que explica su predominio en los programas forestales de fitorremediación que se desarrollan actualmente. Hemos elegido en concreto al híbrido Populus tremula x P. alba, por la facilidad con que se cultiva y su particular interés biotecnológico. La presente Tesis plantea un estudio comprehensivo de la respuesta molecular a bifenilos policlorados (PCBs), una familia de contaminantes orgánicos persistentes de particular relevancia a escala mundial. Se ha utilizado para ello una aproximación transcriptómica, basada en tecnología RNA-seq, para identificar los genes implicados en el metabolismo de los compuestos in planta y cuantificar sus niveles de activación en distintas situaciones controladas. La tesis pretende asimismo definir el control transcripcional subyacente a la respuesta bioquímica frente a este tipo de contaminantes. Resulta sorprendente que dicha respuesta sea prácticamente desconocida a nivel molecular, a pesar de su gran potencial aplicado en el contexto de la tecnología fitorremediadora. Para desarrollar este proyecto aplicamos a nuestros cultivos de chopo híbridos concentraciones diferentes de Aroclor 1221, una mezcla de PCBs muy utilizada a nivel comercial durante décadas, su uso está prohibido hoy internacionalmente. Y tomamos muestras de RNA a dos concentraciones y dos momentos distintos de exposición al contaminante, generando así una matriz de cuatro elementos con sus controles correspondientes. Con el fin de incrementar la especificidad de nuestro análisis, consideramos sobre todo los genes diferencialmente expresados más significativos según cuatro algoritmos estadísticos distintos. Por otra parte, realizamos análisis funcionales con herramientas bioinformáticas basadas en comparaciones de secuencias y en redes de co-expresión génica. La respuesta de los genes de particular interés fue validada mediante tecnología qRT-PCR (reacción de la polimerasa en cadena cuantitativa en tiempo real). Se trata del primer estudio comprehensivo de la respuesta de un organismo vegetal ante la presencia de PCBs. Este estudio nos ha permitido identificar una cantidad considerable de genes estructurales y reguladores, definiendo nuevos factores de transcripción cuya expresión es proporcional a la concentración de contaminante en el medio o al tiempo de exposición al mismo. Los análisis de correlación nos permiten afirmar en que la respuesta metabólica a PCBs, incluyendo posibles rutas degradadoras, participan en al menos quince factores de transcripción y unas cuarenta proteínas o enzimas que resultan particularmente inducidas. Entre las familias implicadas destacan los citocromos P450, la glutatión transferasas, las deshidrogenasas reductasas (short-chain dehydrogenase reductase) y las proteínas MDR (multi-drug resistance). Mientras que los factores de transcripción encontrados pertenecen a la familia de ZF-TF, MYBs, WRKYs entre otros. También identificamos proteínas de función desconocida que no se habían vinculado previamente a este tipo de respuestas en plantas, como la CSP (cold-shock domain proteins). Para estudiar su posible relación con la presencia de PCBs, se caracterizó un gen de esta familia detectado mediante espectrometría de masas en tándem (MS/MS) a partir de mapas IEF x SDS-PAGE (isoelectro focusing x sodium dodecyl sulphate- polyacrylamide gel electrophoresis) de alta resolución. Mediante qRT-PCR pudimos confirmar la inducción del gen correspondiente, ortólogo a PtCSP4 de P. trichocarpa (Potri.004g172600), en respuesta a Aroclor 1221. El análisis fenotípico de las líneas transgénicas de Arabidopsis thaliana que sobre-expresaba la proteína CSP de chopo híbrido confirmó un papel para la misma tolerancia a PCBs, posiblemente a través de mecanismos reguladores que activan proteínas MDR. Este trabajo, además de aportar datos novedosos sobre los mecanismos moleculares desencadenados por la presencia de un PCB en Populus, utilizado aquí como sistema modelo. Con ello se demuestra el potencial de las especies arbóreas no solo como agentes descontaminantes, ya explotado comercialmente, sino también como fuente potencial de genes interesantes. Entre los genes identificados en esta Tesis hay candidatos evidentes a participar en mecanismos de tolerancia al estrés inducido por la contaminación y también rutas metabólicas degradadores de PCBs. Precisamente la posibilidad de degradar al contaminante confiere particular interés a este tipo de estudios frente a la fitorremediación de metales pesados y otros contaminantes elementales. La comparación de los datos generados en este estudio con estudios análogos que se realicen en el futuro con otras especies y xenobióticos, contribuirán a definir mejor la respuesta de las plantas ante la contaminación orgánica y mejorar su potencial descontaminante. ABSTRACT Soil degradation has acquired a disturbing magnitude. Traditional methods of decontamination are expensive and insufficient. Phytoremediation represent an effective alternative, low cost, respectful of the environment, that also improves soil properties, although there have been relevant developments in the last decade. From a life scientist, the challenge is to decipher the major metabolic pathways involved in response to pollutants and understand their regulation. This information is essential if we desire to enhance the natural abilities of some plant species to remediate contaminated soils. This thesis studies have focused on Populus, the best available forestry model following the sequencing of the entire genome. Moreover, Populus has a natural ability to degrade organic pollutants, which explains its predominance in phytoremediation forestry programs currently being developed. We have chosen specifically to hybrid Populus tremula x P. alba, the ease with which it is grown and its particular biotechnological interest. This thesis presents a comprehensive study of the molecular response to polychlorinated biphenyls (PCBs), a family of persistent organic pollutants of particular relevance worldwide. It has been used for a transcriptomic approach using RNA-seq technology, to identify genes involved in the metabolism of compounds in plant and quantify their levels of activation in different controlled situations. The thesis also aims to define the underlying transcriptional control the biochemical response to these pollutants. It is surprising that the response is virtually unknown at the molecular level, despite its great potential applied in the context of phytoremediation technology. To develop this project we applied our hybrid poplar crops different concentrations of Aroclor 1221, a mixture of PCBs widely used commercially for decades, its use is now banned internationally. And we RNA samples at two different concentrations and times of exposure to the pollutant, generating an array of four elements with their corresponding controls. In order to increase the specificity of our analysis, we consider mainly the most significant differentially expressed genes in four different statistical algorithms. Moreover, functional analyzes conducted with bioinformatics tools based on sequence comparisons and networks gene co-expression. The response of genes of particular interest was validated by qRT-PCR (polymerase reaction chain in real-time quantitative. This is the first comprehensive study of the response of a plant organism in the presence of PCBs. This study allowed us to identify a considerable amount of structural and regulatory genes, defining new transcription factors whose expression is proportional to the concentration of contaminant in the middle or at the time of exposure. Correlation analyzes allow us to affirm that the metabolic response to PCBs, including possible degradative pathways, at least fifteen involved in transcription factors and forty proteins or enzymes which are particularly induced. Among the families involved include cytochromes P450, the glutathione transferases, dehydrogenases reductases (short -chain dehydrogenase reductase) and MDR proteins (multi - drug resistance). While transcription factors belong to the family found ZF-TF, MYBs, WRKYs among others. We also identify proteins of unknown function that had not been previously linked to such responses in plants such as CSP (cold- shock domain proteins). To study their possible relationship with the presence of PCBs, a gene in this family was characterized and was detected by tandem mass spectrometry (MS/MS) from maps IEF x SDS -PAGE (sodium dodecyl isoelectro x sulphate- polyacrylamide gel electrophoresis) of high resolution. By qRT -PCR could confirm the induction of the corresponding gene, ortholog to PtCSP4 of P. trichocarpa (Potri.004g172600), in response to Aroclor 1221. Phenotypic analysis of transgenic Arabidopsis thaliana lines over- expressing the protein CSP poplar hybrid confirmed a role for PCBs same tolerance, possibly through regulatory mechanisms activated MDR proteins. This work, in addition to providing new data on the molecular mechanisms triggered by the presence of PCBs in Populus, used here as a model system. Thus the potential of tree species not only as decontamination agents, and commercially exploited, but also as a potential source of interesting genes is shown. Among the genes identified in this thesis there are evident candidates to participate in tolerance mechanisms to stress induced by pollution and degrading metabolic pathways of PCBs. Precisely the possibility of degrading the pollutant attaches particular interest to this type of study off the phytoremediation of heavy metals and other elemental pollutants. The comparison of the data generated in this study with similar studies carried out in the future with other species and xenobiotics contribute to better define the response of plants to organic pollution and improve their decontamination potential.

Sunflower meal and spring pea ruminal degradation protection using malic acid or orthophosphoric acid-heat treatments

The effects of solutions of malic or orthophosphoric acids (0.752 Eqg/kg of feed) and heat to protect proteins of sunflower meal (SFM) and spring pea (SP) against ruminal degradation were studied using particle transit, 15N infusion, in situ and electrophoretic techniques. Three wethers fitted with rumen and duodenum cannulae were successively fed three isoproteic diets including SFM and SP, untreated or treated with malic or orthophosphoric acids. Incubations of tested meals were only performed while feeding the respective diet. Estimates of the ruminally undegraded fraction (RU) and its intestinal digestibility of dry matter, organic matter (only for RU), crude protein and starch (only in SP) were obtained considering ruminal microbial contamination and particle comminution and outflow rates. When corrected for microbial contamination, estimates of RU and intestinal digestibility decreased in all tested fractions for both feeds. All RU estimates increased with the protective treatments, whereas intestinal digestibility-dry matter also increased in SFM. Low intestinal digestibility-crude protein values suggested the presence of antitrypsin factors in SP. Protective treatments of both feeds led to consistent increases in the intestinal digested fraction of dry matter and crude protein, being only numerically different for SP-starch (60.5% as average). However, treatments also reduced the organic matter fermentation, which may decrease ruminal microbial protein synthesis. Electrophoretic studies showed albumin disappearance in both SFM and SP, whereas changes in other RU proteins were more pronounced in SP than SFM.

Improvement of root architecture under abiotic stress through control of auxin homeostasis in Arabidopsis and Brassica crops

Auxin plays an important role in many aspects of plant development including stress responses. Here we briefly summarize how auxin is involved in salt stress, drought (i.e. mostly osmotic stress), waterlogging and nutrient deficiency in Brassica plants. In addition, some mechanisms to control auxin levels and signaling in relation to root formation (under stress) will be reviewed. Molecular studies are mainly described for the model plant Arabidopsis thaliana, but we also like to demonstrate how this knowledge can be transferred to agriculturally important Brassica species, such as Brassica rapa, Brassica napus and Brassica campestris. Moreover, beneficial fungi could play a role in the adaptation response of Brassica roots to abiotic stresses. Therefore, the possible influence of Piriformospora indica will also be covered since the growth promoting response of plants colonized by P. indica is also linked to plant hormones, among them auxin.