High-efficiency voltage regulator and stabilizer for outdoor lighting installations

This paper presents a high performance system of regulation and stabilization of luminous flux for public street lighting installations. Its purpose is to reduce the luminous flux of the luminaries efficiently by reducing their voltage supply, resulting in the improvement of energy efficiency in the installation. The system is basically composed of electromagnetic components which provide robustness and high-performance to the device, as well as minimum maintenance requirements. However, the voltage regulation is based on the application of voltage steps. Aging studies of the luminaries have been carried out to analyze the impact of this discrete voltage regulation. A specific prototype of this voltage and stabilizer regulator have been in operation in a real outdoor lighting installation for more than one year.

Experience with PV-diesel hybrid village power systems in southern Morocco

In October 2002, under the auspices of Spanish Cooperation, a pilot electrification project put into operation two centralised PV-diesel hybrid systems in two different Moroccan villages. These systems currently provide a full-time energy service and supply electricity to more than a hundred of families, six community buildings, street lighting and one running water system. The appearance of the electricity service is very similar to an urban one: one phase AC supply (230V/50Hz) distributed up to each dwelling using a low-voltage mini-grid, which has been designed to be fully compatible with a future arrival of the utility grid. The management of this electricity service is based on a “fee-for-service” scheme agreed between a local NGO, partner of the project, and electricity associations created in each village, which are in charge of, among other tasks, recording the daily energy production of systems and the monthly energy consumption of each house. This register of data allows a systematic evaluation of both the system performance and the energy consumption of users. Now, after four years of operation, this paper presents the experience of this pilot electrification project and draws lessons that can be useful for designing, managing and sizing this type of small village PV-hybrid system

Desarrollo de sistema de gestión de alumbrado público mediante WSN

Este proyecto surge de la búsqueda de un campo de aplicación de las Redes de Sensores Inalámbricos, WSN, aplicadas a la vida cotidiana. Dicha aplicación consistirá en un sistema de gestión de alumbrado público a través del cual se buscará una reducción del consumo energético y del gasto económico, así como una gestión en tiempo de real de la operativa del alumbrado. Para ello se desarrollará un sistema basado en nodos instalados en farolas, los cuales se comunicarán entre sí para funcionar de la forma más optimizada posible, complementándose todo ello con un “nodo base”, que se encargará de servir de nexo entre la red y los diferentes elementos necesarios para la configuración de los nodos y la recogida de información. Esta información servirá para que una página web pueda mostrar al usuario final toda la información necesaria para tener un control sobre el estado actual de funcionamiento de cada una de las farolas, control del consumo, así como detección de averías. En este proyecto se describen las tecnologías actuales relacionadas con el campo de las WSN y los sensores, presentando aplicaciones que en la actualidad se encuentran desplegadas. Se expone también una propuesta real de despliegue presentada al Ayuntamiento de una localidad, Pedro Muñoz, para implementar un proyecto piloto en varias de sus calles. Se describe el entorno, tanto hardware como software, explicando los algoritmos utilizados para las asociaciones entre nodos, diagramas de funcionamiento en las distintas fases de la que está compuesta la operativa de los nodos, la codificación de los programas que se necesitan ejecutar para el correcto funcionamiento del sistema. Por último, debido a que el campo de las WSN está en constante evolución, se presentarán diversas ideas para implementar diversas mejoras que pudieran ser desplegadas en un futuro, ampliando la oferta de aplicaciones a ofrecer al usuario final. ABSTRACT. This project results from the development for an application field of wireless Sensor Networks (WSN), applied to daily life. That application will consist of a system of street lighting management, through which it will seek a reduction in energy consumption and economic cost, and a real-time management of the operative of the street lighting. To do this, a system based on nodes installed in streetlights will be developed. These nodes will communicate with each other to operate in the most optimized way possible, complementing all with a Base-station, which will act as a link between the network and the components required for configuring the nodes and collecting data from them. This information will help a website to show the end user all the information needed to have a control on the current operating status of each of the streetlights, consumption control and troubleshooting. To this end, this project will describe the current technologies related to the field of WSN and sensors, presenting applications that are currently deployed. It will be also exposed a real proposal submitted to a city council to deploy a pilot project in many of its streets. Will be described the environment, both hardware and software, explaining the algorithms used for the associations between nodes, operating diagrams in the different phases of the nodes operation, and the coding of programs that are needed for proper system performance. Finally, because the field of WSN is in constant evolution, will be presented different ideas to implement various improvements which could be deployed in the future, extending the range of applications to provide to end-users.

Caracterización de LEDs mediante el uso y programación de espectrómetro

En la búsqueda de dispositivos cada vez más eficientes, de larga duración y bajo coste de mantenimiento en el mundo de la iluminación, aparecen los LEDs. Estos pequeños dispositivos van poco a poco sustituyendo a las bombillas tradicionales de incandescencia, tomando un papel cada vez más importante entre las fuentes de iluminación. Las primeras funciones prácticas que tuvieron estos LEDs fueron como indicadores, y sus primeros usos fueron en pantallas de calculadoras, electrodomésticos, etcétera, y más adelante, con el desarrollo de nuevos materiales, se empezaron a utilizar como dispositivos de iluminación. Ha sido en estos últimos años cuando se ha producido un salto cuantitativo gracias a la aparición de los POWER LED (LEDs de potencia) o de alto brillo, que son los que han permitido ampliar el uso de estos dispositivos como fuentes de iluminación en, por ejemplo, hogares, alumbrado público, e incluso llegando a sustituir los faros halógenos de vehículos por iluminación LED en algunos modelos. Es por ello que mientras su potencia lumínica va aumentado, su rango de utilización también lo hace. Para caracterizar estas fuentes lumínicas y otras a las que se les pueden dar diferentes usos, se desarrolla este proyecto mediante el análisis de su espectro. Para ello, además, se hará un análisis del resto de instrumentación necesaria que forma parte del proyecto. Este análisis abarca el estudio del propio espectrómetro tanto a nivel de hardware como de software, que modificaremos según los intereses del proyecto. También se estudiará la fibra óptica y el driver para controlar los dispositivos LEDs de potencia, así como los propios LEDs. Para ello se medirán las características de estos LEDs y se compararán con las facilitadas por el fabricante. ABSTRACT. Searching for more efficient, long lasting an low-maintenance devices in lighting world, LEDs appear. These small devices are gradually replacing traditional incandescent bulbs. LEDs are taking an increasingly important role between the light sources. At the begining they were only used as indicators and their first use were in screens calculators, appliances, etc., and later, with the development of new materials, were progressively used as lighting devices. Nowadays a great development has happened in LED lighting with the apparition of the POWER LED or high bright. Power LEDs are allowed to extend the use of these devices as lighting sources for example for homes, street lighting, and even coming to replace halogen headlights LED lighting in vehicles of some models. That's the reason the more their lighting power increases the more their use increases too. The aim of this project is to characterize these light sources and others that can be given different uses by analyzing its spectrum. Moreover, necessary instruments will also be analysed. This study involves both hardware and software spectrometer analysis itself by modifying its software according to the interests of the project. Furthermore, optical fiber and the driver to control LED power devices will be studied by measuring LEDs characteristics and comparing with those provided by the manufacturer.

Implementación y análisis de luminarias LED

En este proyecto se abordan el diseño y análisis, con sus diferentes etapas, de varias configuraciones de prototipos para luminarias LED enfocadas al ámbito domestico e industrial. Se realizarán montajes sobre diferentes materiales para evaluar los resultados y decidir que soporte es más adecuado para cada circunstancia. Inicialmente expondremos el estado actual de esta tecnología y caracterizaremos, de forma preliminar, los dispositivos que vamos a utilizar para elaborar los prototipos que posteriormente analizaremos. Seguidamente detallaremos el proceso de construcción de cada prototipo, indicando especialmente las diferencias y similitudes entre ellos que, en siguientes secciones, serán analizadas. Trabajaremos con dos rangos de potencia para las luminarias. El primero de ellos se centra en obtener la máxima potencia lumínica, con valores comprendidos entre 40W y 50W, considerando un uso industrial, alumbrado público, etc. El segundo rango de potencias, se enfocará al ámbito doméstico, adecuando la temperatura de color a este entorno, para combinar la potencia, de entre 9W y 12W, con una iluminación más cálida. Finalmente someteremos los prototipos elaborados a una serie de análisis y, ante los resultados, concluiremos cuales serán aptos para el uso al que se pretenden dedicar y aquellos que deberán ser modificados. En el entorno de laboratorio, donde se llevaran a cabo análisis térmicos, eléctricos y lumínicos, emplearemos instrumental especializado para cada tipo de análisis así como su software correspondiente. A excepción de las mediciones relacionadas con el espectro de radiación lumínica, el resto serán obtenidas mediante la plataforma LabVIEW®, un completo software grafico para el desarrollo de instrumentación virtual. Como sección final, expondremos una evaluación sobre el cumplimiento de los objetivos establecidos para el proyecto, posibles mejoras o trabajos futuros y conclusiones obtenidas. ABSTRACT. This project concerns the design and analysis, with its different stages, of various configurations of LED luminaries prototypes focused on domestic and industrial environments. Mounts on different materials will be made to evaluate the results and decide which material is most appropriate for each circumstance. Initially we will expose the current state of this technology and characterize, in a preliminary way, the devices that we will use to produce the prototypes which subsequently will analyze. Later we detail the process of construction of each prototype, especially indicating the differences and similarities between them. In the following sections, we will analyze these characteristics. We will work with two power ranges for luminaries. The first one focuses on maximum light output, with values between 40W and 50W, thinking about industrial use, street lighting, etc. The second power range will focus on the domestic environment, adjusting the color temperature in this environment to combine power, between 9W and 12W, with warm lighting. Finally the prototypes will submit a series of analyzes and, with the results obtained, we conclude if will be suitable for the intended use and those that should be modified. In laboratory environment, where thermal, electrical and lighting analyzes were carried out, we will use specialized instruments for each type of analysis as well as the corresponding software. Except for measurements related to the spectrum of light radiation, the rest of information will be obtained by LabVIEW®, complete graphical development software for virtual instrumentation. As a final section, we will present an evaluation of compliance with the project objectives, possible future work, or improvements, and conclusions.

Geochemistry and risk assessment of street dust in Luanda, Angola, a tropical urban environment

A total of 92 samples of street dust were collected in Luanda, Angola, were sieved below 100 μm, and analysed by ICP-MS for 35 elements after an aqua-regia digestion. The concentration and spatial heterogeneity of trace elements in the street dust of Luanda are generally lower than in most industrialized cities in the Northern hemisphere. These observations reveal a predominantly “natural” origin for the street dust in Luanda, which is also manifested in that some geochemical processes that occur in natural soils are preserved in street dust: the separation of uranium from thorium, and the retention of the former by carbonate materials, or the high correlation between arsenic and vanadium due to their common mode of adsorption on solid particles in the form of oxyanions. The only distinct anthropogenic fingerprint in the composition of Luanda's street dust is the association Pb–Cd–Sb–Cu (and to a lesser extent, Ba–Cr–Zn). The use of risk assessment strategies has proved helpful in identifying the routes of exposure to street dust and the trace elements therein of most concern in terms of potential adverse health effects. In Luanda the highest levels of risk seem to be associated (a) with the presence of As and Pb in the street dust and (b) with the route of ingestion of dust particles, for all the elements included in the study except Hg, for which inhalation of vapours presents a slightly higher risk than ingestion. However, given the large uncertainties associated with the estimates of toxicity values and exposure factors, and the absence of site-specific biometric factors, these results should be regarded as preliminary and further research should be undertaken before any definite conclusions regarding potential health effects are drawn.

Origin and patterns of distribution of trace elements in street dust. Unleaded petrol and urban lead

The elemental composition, patterns of distribution and possible sources of street dust are not common to all urban environments, but vary according to the peculiarities of each city. The common features and dissimilarities in the origin and nature of street dust were investigated through a series of studies in two widely different cities, Madrid (Spain) and Oslo (Norway), between 1990 and 1994. The most comprehensive sampling campaign was carried out in the Norwegian capital during the summer of 1994. An area of 14 km2, covering most of downtown Oslo and some residential districts to the north of the city, was divided into 1 km2 mapping units, and 16 sampling increments of approximately 150 g were collected from streets and roads in each of them. The fraction below 100 μm was acid-digested and analysed by ICP-MS. Statistical analyses of the results suggest that chemical elements in street dust can be classified into three groups: “urban” elements (Ba, Cd, Co, Cu, Mg, Pb, Sb, Ti, Zn), “natural” elements (Al, Ga, La, Mn, Na, Sr, Th, Y) and elements of a mixed origin or which have undergone geochemical changes from their original sources (Ca, Cs, Fe, Mo, Ni, Rb, Sr, U). Soil resuspension and/or mobilisation appears to be the most important source of “natural” elements, while “urban” elements originate primarily from traffic and from the weathering and corrosion of building materials. The data for Pb seem to prove that the gradual shift from leaded to unleaded petrol as fuel for automobiles has resulted in an almost proportional reduction in the concentration of Pb in dust particles under 100 μm. This fact and the spatial distribution of Pb in the city strongly suggest that lead sources other than traffic (i.e. lead accumulated in urban soil over the years) may contribute as much lead, if not more, to urban street dust.

Variation of PM2.5 concentrations in relation to street washing activities

Several studies conducted in urban areas have pointed out that road dust resuspension contributes significantly to PM concentration levels. Street washing is one of the methods proposed to reduce resuspended road dust contributions to ambient PM concentrations. As resuspended particles are mainly found in the coarse mode, published studies investigating the effects of street washing have focused on PM10 size fraction. As the PM2.5 mass fraction of particles originating from mechanical abrasion processes may still be significant we conducted a study in order to evaluate the effects of street washing on the mitigation of resuspension of fine particles. The PM2.5 mass concentration data were examined and integrated with the occurrence of street washing activities. In addition, the effect of the meteorological variability, traffic flow and street washing activities, on ambient PM2.5 levels was valuated by means of a multivariate regression model. The results revealed that traffic low is the most important factor that controls PM2.5 hourly concentrations while street washing activities did not influence fine particle mass levels.

Smooth light extraction in lighting optical fibre

Smooth light extraction in lighting optical fibre

Advances in optics for solid state lighting

Optics and LEDs, design Methods, design examples, conclusions

Lighting technology

From the economic point of view, additional lighting at night causes enormous costs and is responsible for using up a massive percentage of the worlds energy resources. During recent years, development trends in the field of LED technology have paved the way for novel concepts impacting on the subject oflight. In this way, the abovementioned issues can be greatly reduced resulting in a better balance between the environment and human needs.

Los dibujos de arquitectura gótica española de George E. Street

Between 1861 and 1863 the British architect George E. Street made several trips in order to study the Spanish gothic architecture, not so well known until then. He published afterwards, in 1865, a book entitled Some Account of Gothic Architecture in Spain which became the standard reference on the issue for generations of British and Spanish scholars. His work was supported by an incredible amount of reliable drawings he managed to create on the spot, that were enthusiastically greeted by critics and historians of the architecture. In this paper we will trace the path of his journeys and present the catalogue of his Spanish sketchbooks, analyzing his technique -in the context of his forerunners- and its reception in the academic world, both in Spain and England.

Correction of the Colour Variations under Uncontrolled Lighting Conditions

Esta tesis trata sobre métodos de corrección que compensan la variación de las condiciones de iluminación en aplicaciones de imagen y video a color. Estas variaciones hacen que a menudo fallen aquellos algoritmos de visión artificial que utilizan características de color para describir los objetos. Se formulan tres preguntas de investigación que definen el marco de trabajo de esta tesis. La primera cuestión aborda las similitudes que se dan entre las imágenes de superficies adyacentes en relación a su comportamiento fotométrico. En base al análisis del modelo de formación de imágenes en situaciones dinámicas, esta tesis propone un modelo capaz de predecir las variaciones de color de la región de una determinada imagen a partir de las variaciones de las regiones colindantes. Dicho modelo se denomina Quotient Relational Model of Regions. Este modelo es válido cuando: las fuentes de luz iluminan todas las superficies incluídas en él; estas superficies están próximas entre sí y tienen orientaciones similares; y cuando son en su mayoría lambertianas. Bajo ciertas circunstancias, la respuesta fotométrica de una región se puede relacionar con el resto mediante una combinación lineal. No se ha podido encontrar en la literatura científica ningún trabajo previo que proponga este tipo de modelo relacional. La segunda cuestión va un paso más allá y se pregunta si estas similitudes se pueden utilizar para corregir variaciones fotométricas desconocidas en una región también desconocida, a partir de regiones conocidas adyacentes. Para ello, se propone un método llamado Linear Correction Mapping capaz de dar una respuesta afirmativa a esta cuestión bajo las circunstancias caracterizadas previamente. Para calcular los parámetros del modelo se requiere una etapa de entrenamiento previo. El método, que inicialmente funciona para una sola cámara, se amplía para funcionar en arquitecturas con varias cámaras sin solape entre sus campos visuales. Para ello, tan solo se necesitan varias muestras de imágenes del mismo objeto capturadas por todas las cámaras. Además, este método tiene en cuenta tanto las variaciones de iluminación, como los cambios en los parámetros de exposición de las cámaras. Todos los métodos de corrección de imagen fallan cuando la imagen del objeto que tiene que ser corregido está sobreexpuesta o cuando su relación señal a ruido es muy baja. Así, la tercera cuestión se refiere a si se puede establecer un proceso de control de la adquisición que permita obtener una exposición óptima cuando las condiciones de iluminación no están controladas. De este modo, se propone un método denominado Camera Exposure Control capaz de mantener una exposición adecuada siempre y cuando las variaciones de iluminación puedan recogerse dentro del margen dinámico de la cámara. Los métodos propuestos se evaluaron individualmente. La metodología llevada a cabo en los experimentos consistió en, primero, seleccionar algunos escenarios que cubrieran situaciones representativas donde los métodos fueran válidos teóricamente. El Linear Correction Mapping fue validado en tres aplicaciones de re-identificación de objetos (vehículos, caras y personas) que utilizaban como caracterísiticas la distribución de color de éstos. Por otra parte, el Camera Exposure Control se probó en un parking al aire libre. Además de esto, se definieron varios indicadores que permitieron comparar objetivamente los resultados de los métodos propuestos con otros métodos relevantes de corrección y auto exposición referidos en el estado del arte. Los resultados de la evaluación demostraron que los métodos propuestos mejoran los métodos comparados en la mayoría de las situaciones. Basándose en los resultados obtenidos, se puede decir que las respuestas a las preguntas de investigación planteadas son afirmativas, aunque en circunstancias limitadas. Esto quiere decir que, las hipótesis planteadas respecto a la predicción, la corrección basada en ésta y la auto exposición, son factibles en aquellas situaciones identificadas a lo largo de la tesis pero que, sin embargo, no se puede garantizar que se cumplan de manera general. Por otra parte, se señalan como trabajo de investigación futuro algunas cuestiones nuevas y retos científicos que aparecen a partir del trabajo presentado en esta tesis. ABSTRACT This thesis discusses the correction methods used to compensate the variation of lighting conditions in colour image and video applications. These variations are such that Computer Vision algorithms that use colour features to describe objects mostly fail. Three research questions are formulated that define the framework of the thesis. The first question addresses the similarities of the photometric behaviour between images of dissimilar adjacent surfaces. Based on the analysis of the image formation model in dynamic situations, this thesis proposes a model that predicts the colour variations of the region of an image from the variations of the surrounded regions. This proposed model is called the Quotient Relational Model of Regions. This model is valid when the light sources illuminate all of the surfaces included in the model; these surfaces are placed close each other, have similar orientations, and are primarily Lambertian. Under certain circumstances, a linear combination is established between the photometric responses of the regions. Previous work that proposed such a relational model was not found in the scientific literature. The second question examines whether those similarities could be used to correct the unknown photometric variations in an unknown region from the known adjacent regions. A method is proposed, called Linear Correction Mapping, which is capable of providing an affirmative answer under the circumstances previously characterised. A training stage is required to determine the parameters of the model. The method for single camera scenarios is extended to cover non-overlapping multi-camera architectures. To this extent, only several image samples of the same object acquired by all of the cameras are required. Furthermore, both the light variations and the changes in the camera exposure settings are covered by correction mapping. Every image correction method is unsuccessful when the image of the object to be corrected is overexposed or the signal-to-noise ratio is very low. Thus, the third question refers to the control of the acquisition process to obtain an optimal exposure in uncontrolled light conditions. A Camera Exposure Control method is proposed that is capable of holding a suitable exposure provided that the light variations can be collected within the dynamic range of the camera. Each one of the proposed methods was evaluated individually. The methodology of the experiments consisted of first selecting some scenarios that cover the representative situations for which the methods are theoretically valid. Linear Correction Mapping was validated using three object re-identification applications (vehicles, faces and persons) based on the object colour distributions. Camera Exposure Control was proved in an outdoor parking scenario. In addition, several performance indicators were defined to objectively compare the results with other relevant state of the art correction and auto-exposure methods. The results of the evaluation demonstrated that the proposed methods outperform the compared ones in the most situations. Based on the obtained results, the answers to the above-described research questions are affirmative in limited circumstances, that is, the hypothesis of the forecasting, the correction based on it, and the auto exposure are feasible in the situations identified in the thesis, although they cannot be guaranteed in general. Furthermore, the presented work raises new questions and scientific challenges, which are highlighted as future research work.

Spatial and temporal variations of trace element distribution in soils and street dust of an industrial town in NW Spain: 15 years of study

Extensive spatial and temporal surveys, over 15 years, have been conducted in soil in urban parks and street dusts in one of the most polluted cities in western Europe, Avilés (NW Spain). The first survey was carried out in 1996, and since then monitoring has been undertaken every five years. Whilst the sampling site is a relatively small town, industrial activities (mainly the steel industry and Zn and Al metallurgy) and other less significant urban sources, such as traffic, strongly affect the load of heavy metals in the urban aerosol. Elemental tracers have been used to characterise the influence of these sources on the composition of soil and dust. Although PM10 has decreased over these years as a result of environmental measures undertaken in the city, some of the “industrial” elements still remain in concentrations of concern for example, up to 4.6% and 0.5% of Zn in dust and soil, respectively. Spatial trends in metals such as Zn and Cd clearly reflect sources from the processing industries. The concentrations of these elements across Europe have reduced over time, however the most recent results from Avilés revealed an upward trend in concentration for Zn, Cd, Hg and As. A risk assessment of the soil highlighted As as an element of concern since its cancer risk in adults was more than double the value above which regulatory agencies deem it to be unacceptable. If children were considered to be the receptors, then the risk nearly doubles from this element.

Road Dust Emission Sources and Assessment of Street Washing Effect

Although previous studies report on the effect of street washing on ambient particulate matter levels, there is a lack of studies investigating the results of street washing on the emission strength of road dust. A sampling campaign was conducted in Madrid urban area during July 2009 where road dust samples were collected in two sites, namely Reference site (where the road surface was not washed) and Pelayo site (where street washing was performed daily during night). Following the chemical characterization of the road dust particles the emission sources were resolved by means of Positive Matrix Factorization, PMF (Multilinear Engine scripting) and the mass contribution of each source was calculated for the two sites. Mineral dust, brake wear, tire wear, carbonaceous emissions and construction dust were the main sources of road dust with mineral and construction dust being the major contributors to inhalable road dust load. To evaluate the effectiveness of street washing on the emission sources, the sources mass contributions between the two sites were compared. Although brake wear and tire wear had lower concentrations at the site where street washing was performed, these mass differences were not statistically significant and the temporal variation did not show the expected build-up after dust removal. It was concluded that the washing activities resulted merely in a road dust moistening, without effective removal and that mobilization of particles took place in a few hours between washing and sampling. The results also indicated that it is worth paying attention to the dust dispersed from the construction sites as they affect the emission strength in nearby streets.