Rammed earth walls in the late middle age castles in the actual province of Soria, Spain

This paper analyzed the building techniques based in the use of rammed earth in the Late Medieval fortifications in the province of Soria, Spain. The manorial castles of Serón de Nágima and Yanguas were built completely with rammed earth. However, these techinques are different. Through the study of the constructive signals, we can reconstruct the constructive process and made an hypothesis of the auxiliary scaffolding necessary for the construction. After, other four cases in which there is presence of rammed earth are described: Ágreda, Arcos de Jalón, Caracena and the tower of Martín González or castle of La Raya (the Border). Rammed earth is used in some secondary architectural elements and also as a filling of the masonry walls, but somtimes there are ancient rammed earth walls overlaid with stone masonry.

Hontoria’s stone (Burgos, Spain): Characteristics and weathering

This paper deals with petrological and petrophysical features of the Hontaria's stone, Burgos (Spain), with which many important monuments were built in northern Spain, in orderr to establish a basis for individual monument restoration. The study contains an historical reference to sorne buildings in which this stone was employed, geological considerations of the origin area, laboratory analysis of the samples, and results of the most common characterization tests. As a conclusion, it can be stated that the Hontoria's stone is apure limestone, with good mechanical and hydrological behaviour, resistent to weathering, easy to quarry (underground mining) and with large resources

Estudio experimental del Sistema de Albañilería Integral en la construcción de viviendas sismorresistentes. Experimental study of the Integral Masonry System in the construction of earthquake resistant houses

This paper presents the application of the Integral Masonry System (IMS) to the construction of earthquake resistant houses and its experimental study. To verify the security of this new type of building in seismic areas of the third world two prototypes have been tested, one with adobe and the other with hollow brick. In both cases it’s a two-story 6x6x6 m3 house built to scale 1/2. The tests are carried out at the Laboratory of Antiseismic Structures of the Department of Engineering, Pontifical Catholic University of Peru in Lima, in collaboration with the UPM (Technical University of Madrid). This article shows the design process of the prototypes to test, including the sizing of the reinforcements, the characteristics of the tests and the results obtained. These results show that the IMS with adobe or brick remains stable with no significant cracks faced with a severe earthquake, with an estimated acceleration of 1.8 g. Este artículo presenta una aplicación del Sistema de Albañilería Integral (SAI) a la construcción de viviendas sismorresistentes y su estudio experimental. Para verificar su seguridad para su construcción en zonas sísmicas del tercer mundo se han ensayado dos prototipos, uno con adobe, y otro con ladrillo hueco. Se trata de una vivienda de 6x6x6 m3 y dos plantas que se construyen a escala 1/2. Los ensayos se realizaron en el Laboratorio de Estructuras Antisísmicas del Departamento de Ingeniería de la Pontificia Católica Universidad del Perú (PUCP) de Lima en colaboración con la UPM (Universidad Politécnica de Madrid). Este artículo muestra el proceso de diseño de los prototipos a ensayar, incluido el dimensionado de los refuerzos, las características de los ensayos y los resultados obtenidos. Estos resultados muestran que el SAI con adobe o ladrillo permanece estable sin grietas significativas ante un sismo severo, con una aceleración estimada de 1,8 g.

Bovedas Encamonadas: Origen, Evolucion, Geometria y Construccion entre los Siglos XVII y XVIII en el Virreinato de Perú

Desde la creación del Virreinato del Perú, en el siglo XVI, los arcos, bóvedas y cúpulas se acostumbraban a levantar con piedra y fábrica. Sin embargo estas tierras eran sacudidas periodicamente por terremotos, produciendo el colapso de la mayoría de estas edificaciones. Para el siglo XVII los alarifes ya habían experimentado diversas maneras de levantar bóvedas, sin haberse encontrado una respuesta razonable en términos de tiempo, economía y estabilidad frente a los sismos. En medio de este panorama se produjo la introducción de las bóvedas encamonadas a mediados del siglo XVII, consolidandose en el resto de la centuria hasta el punto de terminar convirtiéndose en un recurso tradicional y de estimada elaboración dentro de la arquitectura virreinal peruana. Las bóvedas encamonadas se realizaban con tablas de madera (camones) que se solapaban entre sí para formar arcos (cerchas), los cuales definían la forma que tendrían las bóvedas, y eran estabilizados lateralmente mediante correas. Sobre los arcos y correas se colocaba un cerramiento que podía ser un entablado, unos listones de madera o simplemente un tendido a base de cañas. En la mayoría de casos se finalizaba con un recubrimiento aislante de barro por el extradós y otro decorativo de yeso por el intradós. Precisamente estas bóvedas constituyen el objeto de la presente tesis, específicamente en su devenir histórico entre los siglos XVII y XVIII en el ámbito territorial del Virreinato del Perú, partiendo del examen de los tratados de arquitectura coetáneos y del estudio de las bóvedas de madera en España, para finalizar con el análisis de las características geométricas y constructivas que lograron definir en ellas los alarifes peruanos. Since the creation of the Viceroyalty of Peru, in the sixteenth century, arches, vaults and domes were accustomed to build with stone and masonry. However, these lands were periodically shaken by earthquakes, causing the collapse of most of these buildings. For the seventeenth century the master masons had already experienced several ways to build vaults, without having found a reasonable response in terms of time, economy and stability against earthquakes. Into this context the master carpenters introduced the wooden vaults since seventeenth century, and this constructive system was consolidated around the rest of the century to the end point of becoming a traditional and estimated resource of the Peruvian colonial architecture. The wooden vaults were made with timber planks (camones) that overlapped each other to form arches (cerchas), which defined the shape of the vaults, and were stabilized laterally by purlins. Above the arches and purlins placed planks, wooden strips or just cane. In most cases ended with a mud plaster insulating the extrados and a decorative gypsum plaster on the intrados. Precisely these vaults are the subject of this thesis, specifically in its historical way between the seventeenth and eighteenth centuries in the territory of the Viceroyalty of Peru. Since an examination of the architectural treatises and the Spanish wooden vaults, and concluding with the analysis of the geometric and constructive system that Peruvian builders were able to define on them.

The Ciborium or Lantern Tower of Valencia Cathedral: Geometry, Construction and Stability

Early 18th century treatise writer Tomas Vicente Tosca1 includes in his Tratado de la montea y cortes de Canteria [On Masonry Design and Stone Cutting], what is an important documentary source about the lantern of Valencia Cathedral. Tosca writes about this lantern as an example of vaulting over cross arches without the need of buttresses. A geometrical description is followed by an explanation of the structural behavior which manifests his deep understanding of the mechanics of masonry structures. He tries to demonstrate the absence of buttresses supporting his thesis on the appropriate distribution of loads which will reduce the "empujos" [horizontal thrusts] to the point of not requiring more than the thickness of the walls to stand (Tosca [1727] 1992, 227-230). The present article2 assesses T osca' s appreciation studying how loads and the thrusts they generate are transmitted through the different masonry elements that constitute this ciborium. In order to do so, we first present a geometrical analysis and make considerations regarding its materials and construction methods to, subsequently, analyze its stability adopting an equilibrium approach within the theoretical framework of the lower bound limit analysis.

The Ciborium or Lantern Tower of Valencia Cathedral: Geometry, Construction and Stability

Early 18th century treatise writer Tomas Vicente Tosca1 includes in his Tratado de la montea y cortes de Canteria [On Masonry Design and Stone Cutting], what is an important documentary source about the lantern of Valencia Cathedral. Tosca writes about this lantern as an example of vaulting over cross arches without the need of buttresses. A geometrical description is followed by an explanation of the structural behavior which manifests his deep understanding of the mechanics of masonry structures. He tries to demonstrate the absence of buttresses supporting his thesis on the appropriate distribution of loads which will reduce the "empujos" [horizontal thrusts] to the point of not requiring more than the thickness of the walls to stand (Tosca [1727] 1992, 227-230). The present article2 assesses T osca' s appreciation studying how loads and the thrusts they generate are transmitted through the different masonry elements that constitute this ciborium. In order to do so, we first present a geometrical analysis and make considerations regarding its materials and construction methods to, subsequently, analyze its stability adopting an equilibrium approach within the theoretical framework of the lower bound limit analysis.

Numerical analysis of mixe-mode fracture of brickwork masonry with embedded discontinuity elements

One of the common pathologies of brickwork masonry structural elements and walls is the cracking associated with the differential settlements and/or excessive deflections of the slabs along the life of the structure. The scarce capacity of the masonry in order to accompany the structural elements that surround it, such as floors, beams or foundations, in their movements makes the brickwork masonry to be an element that frequently presents this kind of problem. This problem is a fracture problem, where the wall is cracked under mixed mode fracture: tensile and shear stresses combination, under static loading. Consequently, it is necessary to advance in the simulation and prediction of brickwork masonry mechanical behaviour under tensile and shear loading. The quasi-brittle behaviour of the brickwork masonry can be studied using the cohesive crack model whose application to other quasibrittle materials like concrete has traditionally provided very satisfactory results.

Normalización del análisis de la piedra y conservación del patrimonio cultural. The Standardization of Stone Analysis and Conservation of Cultural Heritage

La normalización de los métodos de análisis y de los principales aspectos relacionados con la conservación de los bienes culturales ha empezado en 2004 con la creación del comité europeo de normalización, CEN/TC 346 Conservation of Cultural Property, que tiene la responsabilidad no solamente de redactar protocolos de ensayos en laboratorio, sino también proponer las recomendaciones más adecuadas para designarlos de forma consensual y conservarlos de la forma más apropiada. Se comentan los aspectos relacionados con el origen de estas normas, el trabajo desarrollado y que muchas de ellas, aunque no estén dirigidas específicamente a la piedra, tienen en cuenta la presencia de este material en objetos arqueológicos, obras de arte, estructuras de fábricas y elementos ornamentales.

Wedges and plate-bandes: mechanical theories after De la Hire

Plate-bandes are straight masonry arches (they are called, also, flat arches or lintel arches). Ideally they have the surfaces of extrados and intrados plane and horizontal. The stones or bricks have radial joints converging usually in one centre. The voussoirs have the form of wedges and in French they are called "claveaux". A plate-bande is, in fact, a lintel made of several stones and the proportions of lintels and plate-bandes are similar. Proportions of plate-bandes, that is the relationship between the thickness t and the span s (t/s)varies, typically between 1/4–1/3 in thick plate-bandes, and is less than 1/20 in the most slender ones. A ratio of circa 1/8 was usual in the 18th Century and follows a simple geometrical rule: the centre form with the intrados an equilateral triangle and the plate-bande should contain an arc of circle. The joints are usually plane, but in some cases present a «rebated» or «stepped» form. Plate-bandes exert an inclined thrust as any masonry arch. This thrust is usually very high and it requires either massive buttresses, or to be built in the middle of thick walls. Master builders and architects have tried since antiquity to calculate the abutment necessary for any arch. A modern architect or engineer will measure the arch thrust in units of force, kN or tons. Traditionally, the thrust has been measured as the size of the buttresses to resist it safely. Old structural rules, then, addressed the design problem establishing a relationship between the span and the depth of the buttress. These were empirical rules, particular for every type of arch or structure in every epoch. Thus, the typical gothic buttress is 1/4 of the vault span, but a Renaissance or baroque barrel vault will need more than 1/3 of the span. A plate-bande would require more than one half of the span; this is precisely the rule cited by the French engineer Gautier, who tried unsuccessfully to justify it by static reasons. They were used, typically, to form the lintels of windows or doors (1-2 m, typically); in Antiquity they were used, also, though rarely, at the gates of city walls or in niches (ca. 2 m, reaching 5.2 m). Plate-bandes may show particular problems: it is not unusual that some sliding of the voussoirs can be observed, particularly in thick plate-bandes. The stepped joints on Fig. 1, left, were used to avoid this problem. There are other «hidden» methods, like iron cramps or the use of stone wedges, etc. In seismic zones these devices were usual. Another problem relates to the deformation; a slight yielding of the abutments, or even the compression of the mortar joints, may lead to some cracking and the descent of the central keystone. Even a tiny descent will convert the original straight line of the intrados in a broken line with a visible «kink» or angle in the middle. Of course, both problems should be avoided. Finally, the wedge form of the voussoirs lead to acute angles in the stones and this can produce partial fractures; this occurs usually at the inferior border of the springers at the abutments. It follows, that to build a successful plate-bande is not an easy matter. Also, the structural study of plate-bandes is far from simple, and mechanics and geometry are related in a particular way. In the present paper we will concentrate on the structural aspects and their constructive consequences, with a historical approach. We will outline the development of structural analysis of plate-bandes from ca. 1700 until today. This brief history has a more than purely academic interest. Different approaches and theories pointed to particular problem, and though the solution given may have been incorrect, the question posed was often pertinent. The paper ends with the application of modern Limit Analysis of Masonry Structures, developed mainly by professor Heyman in the last fifty years. The work aims, also, to give some clues for the actual architect and engineer involved in the analysis or restoration of masonry buildings.

Experimental and Analytical Study of Masonry Infill Reinforced Concrete Frames Retrofitted with Steel Braces

In the present work a seismic retrofitting technique is proposed for masonry infilled reinforced concrete frames based on the replacement of infill panels by K-bracing with vertical shear link. The performance of this technique is evaluated through experimental tests. A simplified numerical model for structural damage evaluation is also formulated according to the notions and principles of continuum damage mechanics. The proposed model is calibrated with the experimental results. The experimental results have shown an excellent energy dissipation capacity with the proposed technique. Likewise, the numerical predictions with the proposed model are in good agreement with experimental results.

Modelling the spatio-temporal pattern of primary dispersal in stone pine (Pinus pinea L.) stands in the Northern Plateau (Spain)

Natural regeneration in stone pine (Pinus pinea L.) managed forests in the Spanish Northern Plateau is not achieved successfully under current silviculture practices, constituting a main concern for forest managers. We modelled spatio-temporal features of primary dispersal to test whether (a) present low stand densities constrain natural regeneration success and (b) seed release is a climate-controlled process. The present study is based on data collected from a 6 years seed trap experiment considering different regeneration felling intensities. From a spatial perspective, we attempted alternate established kernels under different data distribution assumptions to fit a spatial model able to predict P. pinea seed rain. Due to P. pinea umbrella-like crown, models were adapted to account for crown effect through correction of distances between potential seed arrival locations and seed sources. In addition, individual tree fecundity was assessed independently from existing models, improving parameter estimation stability. Seed rain simulation enabled to calculate seed dispersal indexes for diverse silvicultural regeneration treatments. The selected spatial model of best fit (Weibull, Poisson assumption) predicted a highly clumped dispersal pattern that resulted in a proportion of gaps where no seed arrival is expected (dispersal limitation) between 0.25 and 0.30 for intermediate intensity regeneration fellings and over 0.50 for intense fellings. To describe the temporal pattern, the proportion of seeds released during monthly intervals was modelled as a function of climate variables – rainfall events – through a linear model that considered temporal autocorrelation, whereas cone opening took place over a temperature threshold. Our findings suggest the application of less intensive regeneration fellings, to be carried out after years of successful seedling establishment and, seasonally, subsequent to the main rainfall period (late fall). This schedule would avoid dispersal limitation and would allow for a complete seed release. These modifications in present silviculture practices would produce a more efficient seed shadow in managed stands.

Low-cost retrofitting solutions for RC frames using masonry infill panels

A large number of reinforced concrete (RC) frame structures built in earthquake-prone areas such as Haiti are vulnerable to strong ground motions. Structures in developing countries need low-cost seismic retrofit solutions to reduce their vulnerability. This paper investigates the feasibility of using masonry infill walls to reduce deformations and damage caused by strong ground motions in brittle and weak RC frames designed only for gravity loads. A numerical experiment was conducted in which several idealized prototypes representing RC frame structures of school buildings damaged during the Port-au-Prince earthquake (Haiti, 2010) were strengthened by adding elements representing masonry infill walls arranged in different configurations. Each configuration was characterized by the ratio Rm of the area of walls in the direction of the ground motion (in plan) installed in each story to the total floor area. The numerical representations of these idealized RC frame structures with different values of Rm were (hypothetically) subjected to three major earthquakes with peak ground accelerations of approximately 0.5g. The results of the non-linear dynamic response analyses were summarized in tentative relationships between Rm and four parameters commonly used to characterize the seismic response of structures: interstory drift, Park and Ang indexes of damage, and total amount of energy dissipated by the main frame. It was found that Rm=4% is a reasonable minimum design value for seismic retrofitting purposes in cases in which available resources are not sufficient to afford conventional retrofit measures.

A Damage Model for Masonry Infilled Frames

The effect of infill walls on the behaviour of frames is widely recognized, and, for several decades now, has been the subject of numerous experimental investigations. However, the analytical modeling of infilled panels and frames under in-plane loading is difficult and generally unreliable. From the point of view of the simulation technique the models may be divided into micromodels and simplified (or macro-) models. Based on the equivalent strut approach (simplified model), in this paper a damage model is proposed for the characterization of masonry walls submitted to lateral cyclic loads. The model, developed along the lines of the Continuum Damage Mechanics, have the advantages of including explicitly the coupling between damage and mechanical behaviour and so is consistent with the definition of damage as a phenomenon with mechanical consequences.

Fundamentos constructivos de las fortificaciones fronterizas entre las coronas de Castilla y Aragón de los siglos XII al XV en la actual provincia de Soria

La tesis doctoral desarrolla una investigación original, dentro del marco disciplinario de la historia de la construcción, sobre los fundamentos constructivos de las fortificaciones bajomedievales fronterizas entre las Coronas de Castilla y Aragón en la actual provincia de Soria. En el título de la tesis ya queda expresado el objeto fundamental y fundacional, así como el ámbito temporal —desde la reconquista del oriente soriano por parte de Alfonso I el Batallador a principios del siglo XII hasta la unificación de las coronas hispánicas en el siglo XV bajo el común mandato de los Reyes Católicos— y la extensión territorial que delimita la investigación: aquéllas comarcas castellanas lindantes con Aragón pertenecientes a la actual provincia de Soria. Durante este período bajomedieval se produjeron una serie de enfrentamientos fronterizos que obligó a fortificar la frontera y las vías de comunicación entre ambas coronas. La falta de estudios de conjunto de estas fortificaciones entendiéndolas como participantes en un sistema fortificado ha constituido la justificación de la investigación, que se realiza en varios niveles de análisis: territorial, histórico, arquitectónico, poliorcético y constructivo. Así mismo, se ha detectado cierta falta de rigor acompañada de inexactitudes en las consideraciones constructivas publicadas sobre algunas de las fortificaciones del ámbito de estudio, lo que ha provocado errores en su datación al no más haber elementos de corte artístico o estilístico que marquen indudablemente la pertenencia a una época. En la tesis se ponen en duda las dataciones tradicionalmente aceptadas planteando la hipótesis que da pie a la investigación: ante la falta de elementos artísticos o estilísticos en unos sobrios edificios eminentemente funcionales es posible establecer con suficiente aproximación la fecha de construcción en base a criterios constructivos una vez formada una clasificación cronotipológica de cada técnica constructiva. La hipótesis, por lo tanto, plantea un objetivo principal —el estudio de la razón constructiva del sistema fortificado fronterizo— desarrollado en una serie de objetivos específicos cuya consecución programa los sucesivos niveles de análisis: - Conocer y detallar los elementos históricos que originaron los enfrentamientos entre las Coronas de Castilla y Aragón y su desarrollo mediante herramientas historiográficas y analizar las características naturales del territorio en litigio mediante instrumentos cartográficos. - Conocer y analizar los tipos arquitectónicos y las tradiciones constructivas empleadas en las construcciones castrenses en el ámbito temporal en que se enmarca la investigación. - Localizar, documentar y seleccionar para su análisis las fortalezas y construcciones militares erigidas durante dichas luchas fronterizas en la actual provincia de Soria a través del trabajo de campo y métodos cartográficos y bibliográficos. - Realizar un estudio general sobre el sistema fortificado a escala territorial - Investigar la tipología arquitectónica, poliorcética y constructiva del conjunto de estas fortificaciones bajomedievales fronterizas. - Analizar los fundamentos constructivos de los casos de estudio seleccionados entre estas construcciones y caracterizarlas en cuanto al material, elementos, sistemas y procesos constructivos. - Ordenar la información histórica dispersa y corregir errores para hacer una base sobre la que establecer un discurso histórico de cada caso de estudio. - Comparar y relacionar las técnicas constructivas empleadas en estas fortalezas con los utilizados en el mismo ámbito temporal. - Difundir para su debate los resultados de la investigación por los foros científicos habituales. El método empleado combina los trabajos de gabinete con una intensa labor de campo, en la que se han documentado cincuenta fortificaciones y se han redactado sus correspondientes fichas de toma de datos. La recopilación de datos se ha incluido en una base de datos que incluye aspectos generales, tipológicos, constructivos y bibliográficos básicos del conjunto, a modo de inventario, de fortificaciones de la provincia. Las fortificaciones seleccionadas se agrupan según una clasificación tipológica y constructiva que marca las líneas de estudio posteriores. Se desarrolla un capítulo de antecedentes en el que se estudia la historia de la construcción fortificada medieval tanto en Europa como en España analizando la evolución de los tipos arquitectónicos y las múltiples influencias culturales que surcaron el Mediterráneo desde el Oriente cruzado e islámico al Poniente donde se desarrollaba la empresa reconquistadora que mantuvo en estado de guerra continuo a la Península Ibérica durante ochocientos años. El análisis del territorio como contenedor del hecho fortificado revela que hay una relación íntima entre la ubicación de las fortificaciones y las formas naturales que definen las vías de comunicación entre los valles del Duero, del Ebro y del Tajo. En efecto, el ámbito de estudio ha supuesto desde la Antigüedad un territorio de paso fundamental en la articulación de las comunicaciones en la Península Ibérica. Este carácter de paso más que de frontera explica las inquietudes y la preocupación por su control tanto por Roma como por el califato cordobés como por los reinos cristianos medievales. El análisis de los elementos históricos se complementa con el estudio detallado de los enfrentamientos fronterizos entre Castilla y Aragón así como los aspectos sociales y políticos que provocaron la fortificación como sistema de definición de la frontera y de organización espacial, jurisdiccional, social y administrativa del territorio. La arquitectura fortificada es esencialmente funcional: su cometido es la defensa. En este sentido, tras un estudio morfológico de los castillos seleccionados se realiza un extenso análisis poliorcético de sus elementos, investigando su origen y aplicación para servir también de parámetros de datación. Siendo el objeto inaugural de la tesis el estudio de los fundamentos constructivos, se explican los distintos materiales de construcción empleados y se agrupan las fábricas de las fortificaciones seleccionadas en dos grandes grupos constructivos: las fábricas aparejadas y las fábricas encofradas. Se han destacado y estudiado la evolución histórica y la tipología y mensiología constructiva de tres técnicas destacadas: el uso del ladrillo, la tapia de cal y canto o mampostería encofrada y la tapia de tierra. Para el estudio de la componente histórica y de la dimensión constructiva de cada técnica ha sido necesario documentar numerosos casos tanto en el ámbito de estudio como en la Península Ibérica con el fin de establecer grupos cronotipológicos constructivos entre los que poder ubicar las fábricas de estas técnicas presentes en el ámbito de estudio. Se ha observado una evolución dimensional de las fábricas de tapia que es más evidente en las hispanomusulmanas al modularse en codos pero que también se advierte significativamente en las cristianas bajomedievales. De cada una de las técnicas analizadas se ha seleccionado un caso de estudio singular y representativo. El castillo de Arcos de Jalón es un ejemplo significativo del empleo de la fábrica mixta de mampostería con verdugadas de ladrillo, así como las murallas de la ciudad fortificada de Peñalcázar lo es de la fábrica de mampostería encofrada y el castillo de Serón de Nágima constituye un caso característico y principal de la utilización de la tapia de tierra en la arquitectura militar bajomedieval. Cada uno de estos tres casos de estudios se examina bajo los mismos cuatro niveles anteriormente mencionados: territorial, histórico, arquitectónico y defensivo y constructivo. El sistemático método de estudio ha facilitado el orden en la investigación y la obtención de unos resultados y conclusiones que verifican la hipótesis y cumplen los objetivos marcados al comienzo. Se ha revisado la datación en la construcción de las fortificaciones analizadas mediante el estudio cronotipológico de sus fábricas, pudiendo trasladarse el método a otros sistemas fortificados. La tesis abre, finalmente, dos vías principales de investigación encaminadas a completar el estudio del sistema fortificado fronterizo bajomedieval en la raya oriental soriana de Castilla: la caracterización y datación por métodos físico-químicos de las muestras de piezas de madera de construcción que se conservan embebidas en las fábricas y la búsqueda documental y archivística que pueda revelar nuevos datos respecto a la fundación, reparación, venta o cualquier aspecto económico, legislativo, organizativo o administrativo relativo a las fortificaciones en documentos coetáneos. ABSTRACT The doctoral thesis develops an original research, held in the field of the Construction History, about the constructive reason of the frontier fortifications in the Late Middle Age between the Crowns of Castile and Aragón in the actual province of Soria, Spain. In the title is expressed the main objective, and also the temporal scope —from the reconquest in the 12th Century by Alfonso the First of Aragón to the unification under the common kingdom of the Catholic Kings— and the territorial extension that the research delimits: those Castilian regions in the border with Aragón in the actual province of Soria. During this period, a series of border wars were been, and this is the reason for the fortification of the border line and the main roads between both Crowns. The lack of studies of these fortifications as participants in a fortified system is the justification of the research. There is several analysis levels: territorial, historical, architectonic, defensive and constructive. Likewise, there is a lack of strictness and inaccuracy in the constructive items in the publications about several fortifications of this study field. This aspect has caused mistakes in the dating because there is neither artistic nor stylistic elements which determines a epoch. The traditionally accepted datings are challenged. An hypothesis is formulated: in the absence of artistic or stylistic elements in a sober and functional buildings is possible to date the time of construction with sufficiently approximation based on construction criteria once formed a cronotypologic classification of each building technique. The hypothesis, therefore, propose a main aim: the study of the constructive reason of the fortified border system. This aim is developed in a series of specifically targets whose achievement programs the analysis levels: - To know and to detail the historical elements which started the wars between Castile and Aragon and its development using historiographical tools, and to analyze the natural characteristic of the territory through cartographical tools. - To understand and to analyze the different architectural types and the building traditions employed in the military buildings in the time researched. - To locate, to document, and to select for their analysis the fortresses and military constructions erected during these border wars in the actual province of Soria through fieldwork and bibliographical and cartographical methods. - To conduct a general study on the fortified system in territorial scale. - To research the architectural, constructive and defensive typology of the system of these border late medieval fortifications. - To analyze the construction logic of the selected case studies and to characterize in the items of material, elements, systems and construction processes. - To sort scattered historical information and to correct mistakes to make a base by which to establish a historic speech of each case study. - To compare and to relate the construction techniques employed in these fortresses with those used in the same time range . - To spread for discussion the research results in the usual scientists forums. The method combines the destock work with an intense fieldwork. Fifty fortifications have been documented and it has written their corresponding data collection card. Data collection has been included in a database that includes general aspects, typological, constructive and basic bibliographical data, as an inventory of fortifications in the province. The selected fortifications are grouped according to a typological and constructive classification which lead the lines of the later study. There is a chapter for the antecedents in which the history of the medieval fortified construction in Europe and in Spain is studied by analyzing the evolution of architectural types and the many cultural influences along the opposite seasides of the Mediterranean Sea, from the Islamic and Crusader East to the Iberian Peninsula in where there were a long and continuous war during eight hundred years. The territory is analyzed as a container of fortifications. This analysis reveals that there is an intimate relationship between the location of the fortifications and the natural forms that define the communication roads between the Duero, Ebro and Tajo valleys. Indeed, the study area has been a cross-territory from ancient times more than a frontierterritory. This communication character explains the concerns about its control both by Rome and by the Muslims of Córdoba as medieval Christian kingdoms. The analysis of historical elements is supplemented by detailed study of border war between Castile and Aragon and the social and political issues that led to the fortification as border definition system and spatial, jurisdictional, social and administrative planning. The fortified architecture is essentially functional: it is responsible for defense. In this sense, after a morphological study of selected castles is performed an extensive analysis of its defensive elements, investigating its origin and application. This analisis serves for the definition of parameters for dating. The purpose of the thesis is the study of the constructive logic. First, various building materials are explained. Then, masonry is grouped into two major constructive groups: rigged masonry and formwork masonry. The historical evolution and the constructive typology and mensiology are studied for each one of the three main techniques: the use of brickwork, the mortar wall and rammed-earth. Many case studies have been documented along the Iberian Peninsula and also in the study area. As conclusion, there is a dimensional evolution of the rammed-earth walls. This evolution is more evident into the Muslim masonry than in the late medieval walls: the reason is the use of the cubit as module. From each of the techniques discussed, a singular and representative case of study has been selected. The castle of Arcos de Jalon is a significant example of mix masonry of stone and brick rows. The walled city of Peñalcázar is built with masonry formwork. Serón de Nágima castle, at last, is a typical and main case of the use of the rammedearth wall of late medieval military architecture. Each of these three case studies were examined under the same four analysis levels above mentioned: territorial, historical, architectural and defensive and constructive. The systematic method of study has facilitated the order in the research and the obtaining of results and conclusions that verify the hypotheses and achieve the research objectives. Dating of the fortifications construction has been revised by studying the cronotypological issues of its masonry. The method can be transferred to the study of other fortified systems. Finally, the thesis describes two main research new ways aimed at completing the study of the late medieval fortified border of Castile in the actual province of Soria. The first of them is the characterization and datig by physicochemical methods the sample pieces of wood construction preserved embedded in the masonry. The second research way is the investigation of the documents in archives that may reveal new information about the foundation, repair, sale or any aspect to economic, legal, organizational or administrative concerning fortifications in contemporary documents.

Study of packing lines for stone fruits and citrus using two instrumented spheres in some cooperatives in the region of Murcia (Spain).

Two instrumented spheres IS 100 were used to evaluate the quality of post-harvest operations. Results obtained from measurements made with both IS (8.8 cm 0 and 6.2 cm 0) show significant differences. Both IS measure the same values of the same variables for soft materials, but not for hard surfaces. Four packing lines belonging to different cooperatives of the region of Murcia (two for stone fruits and two for citrus) were tested. IS values obtained in transfers belonging to the tested lines lay well above 50 g's in most of them Much higher impact intensities are registered in citrus lines than in stone fruit packing lines. To study the incidence of a certain packing line on different products an interaction fruit-packing line test was perf01med. In all cases, more than 50% of fruits belonging to the post-handling sample showed some kind of damage. Bruises evolve after 48 hours storage at room temperature.