Study of the Mechanical Strength Improvement of Wafers for EWT Solar Cells by Chemical Etching after the Drilling Process

Mechanical stability of EWT solar cells deteriorates when holes are created in the wafer. Nevertheless, the chemical etching after the hole generation process improves the mechanical strength by removing part of the damage produced in the drilling process. Several sets of wafers with alkaline baths of different duration have been prepared. The mechanical strength has been measured by the ring on ring bending test and the failure stresses have been obtained through a FE simulation of the test. This paper shows the comparison of these groups of wafers in order to obtain an optimum value of the decreased thickness produced by the chemical etching

Embryogenic suspensions of adult cork oak: the first step towards mass propagation.

Abstract Protocols have been established to clone adult cork oak trees by somatic embryogenesis using semisolid medium. However, for economically viable mass propagation, embryogenic cultures in liquid medium need to be developed. In this study, suspension cultures were initiated from embryo clusters obtained by secondary embryogenesis on a gelled medium lacking plant growth regulators. After 6 days of culture, these embryo clusters generated high cell density suspensions that also contained small organized structures (embryos and embryogenic clumps). As the culture duration increased, tissue necrosis and fewer embryogenic structures were observed and the establishment of suspension cultures failed. An alternative method was found adequate for initiation of embryogenic suspensions: embryo clusters from gelled medium were briefly shaken in liquid medium and detached cells and embryogenic masses of 41?800 lm were used as inoculum. Maintenance of embryogenic suspensions was achieved using a low-density inoculum (43 mg l-1) by subculturing four embryogenic clumps of 0.8?1.2 mm per 70 ml of medium. Proliferation ability was maintained for almost 1 year through ten consecutive subcultures. The initiation and maintenance protocols first developed for a single genotype were effective when tested on 11 cork oak genotypes.

Defect engineering during the contact co-firing step in an industrial belt furnace

This work implements an optimization of the phosphorus gettering effect during the contact co-firing step by means of both simulations and experiments in an industrial belt furnace. An optimized temperature profile, named ‘extended co-firing step’, is presented. Simulations show that the effect of the short annealing on the final interstitial iron concentration depends strongly on the initial contamination level of the material and that the ‘extended co-firing’ temperature profile can enhance the gettering effect within a small additional time. Experimental results using sister wafers from the same multicrystalline silicon ingot confirm these trends and show the potential of this new defect engineering tool to improve the solar cell efficiency.

Damage reduction of the laser drilling process on back contact solar cells by chemical treatment

Production of back contact solar cells requires holes generations on the wafers to keep both positive and negative contacts on the back side of the cell. This drilling process weakens the wafer mechanically due to the presence of the holes and the damage introduced during the process as microcracks. In this study, several chemical processes have been applied to drilled wafers in order to eliminate or reduce the damage generated during this fabrication step. The treatments analyzed are the followings: alkaline etching during 1, 3 and 5 minutes, acid etching for 2 and 4 minutes and texturisation. To determine mechanical strength of the samples a common mechanical study has been carried out testing the samples by the Ring on Ring bending test and obtaining the stress state in the moment of failure by FE simulation. Finally the results obtained for each treatment were fitted to a three parameter Weibull distribution

Resonant absorption in a plasma step profile

Resonant absorption of p-polarized light shined on a plane-layered plasma with a step profile, is discussed as a function of wavelength (or critical density n,) of the light: for simplicity the incidence angle is assumed small. If n, lies within or above the step, the absorption A is given by Ginzburg’s result modified by strong reflections at the foot and top of the step. The absorption above is total for particular values of nc and U. For n, crossing the top of the density step the absorption is not monotonical: it exhibits a minimum that vanishes for zero radius of curvature U there and zero collision frequency 1’ (A - Iln VI-’). The results are applied to the profile produced by irradiating a solid target with a high-intensity pulse that steepens the plasma by radiation pressure.

Image analysis by moment invariants using a set of step-like basis functions

Moment invariants have been thoroughly studied and repeatedly proposed as one of the most powerful tools for 2D shape identification. In this paper a set of such descriptors is proposed, being the basis functions discontinuous in a finite number of points. The goal of using discontinuous functions is to avoid the Gibbs phenomenon, and therefore to yield a better approximation capability for discontinuous signals, as images. Moreover, the proposed set of moments allows the definition of rotation invariants, being this the other main design concern. Translation and scale invariance are achieved by means of standard image normalization. Tests are conducted to evaluate the behavior of these descriptors in noisy environments, where images are corrupted with Gaussian noise up to different SNR values. Results are compared to those obtained using Zernike moments, showing that the proposed descriptor has the same performance in image retrieval tasks in noisy environments, but demanding much less computational power for every stage in the query chain.

Transport of Pru p 3 across gastrointestinal epithelium - an essential step towards the induction of food allergy?

Background Since intestinal absorption of food protein can trigger an allergic reaction, the effect of plant food allergen on intestinal epithelial cell permeability and its ability to cross the epithelial monolayer was evaluated. Objective To study the interaction of Pru p 3 with intestinal epithelium, its natural entrance, analyzing transport kinetics and cellular responses that trigger. Methods This was achieved using Pru p 3, the peach LTP, as a model. Enterocytic monolayers were established by culturing Caco 2 cells, as a model of enterocytes, on permeable supports that separate the apical and basal compartments. Pru p 3 was added to the apical compartment, the transepithelial resistance (TEER) was measured, and the transport was quantified. Results The peach allergen that crossed the cell monolayer was detected in the cell fraction and in the basal medium by immunodetection with specific antibodies and the quantity was measured by ELISA assay. Pru p 3 was able to cross the monolayer without disturbing the integrity of the tight junctions. This transport was significantly higher than that of a non-allergenic peach LTP, LTP1, and occurred via lipid raft pathway. The incubation of Caco 2 cells with Pru p 3 and LTP1 produced the expression of epithelial-specific cytokines TSLP, IL33 and IL25. Conclusion These results suggest that Pru p 3 was able to cross the cell monolayer by the transcellular route and then induce the production of Th2 cytokines. The results of the present study represent a step towards clarifying the importance of Pru p 3 as a sensitizer. Clinical relevance The capacity of food allergens to cross the intestinal monolayer could explain their high allergenic capacity and its fast diffusion through the body associating to severe symptoms.

Estudio de las propiedades mecánicas de obleas de silicio

En esta tesis se propone un procedimiento para evaluar la resistencia mecánica de obleas de silicio cristalino y se aplica en diferentes casos válidos para la industria. En el sector de la industria fotovoltaica predomina la tecnología basada en paneles de silicio cristalino. Estos paneles están compuestos por células solares conectadas en serie y estas células se forman a partir de obleas de silicio. Con el objetivo de disminuir el coste del panel, en los últimos años se ha observado una clara tendencia a la reducción del espesor de las obleas. Esta reducción del espesor modifica la rigidez de las obleas por lo que ha sido necesario modificar la manera tradicional de manipularlas con el objetivo de mantener un bajo ratio de rotura. Para ello, es necesario conocer la resistencia mecánica de las obleas. En la primera parte del trabajo se describen las obleas de silicio, desde su proceso de formación hasta sus propiedades mecánicas. Se muestra la influencia de la estructura cristalográfica en la resistencia y en el comportamiento ya que el cristal de silicio es anisótropo. Se propone también el método de caracterización de la resistencia. Se utiliza un criterio probabilista basado en los métodos de dimensionamiento de materiales frágiles en el que la resistencia queda determinada por los parámetros de la ley de Weibull triparamétrica. Se propone el procedimiento para obtener estos parámetros a partir de campañas de ensayos, modelización numérica por elementos finitos y un algoritmo iterativo de ajuste de los resultados. En la segunda parte de la tesis se describen los diferentes tipos de ensayos que se suelen llevar a cabo con este material. Se muestra además, para cada uno de los ensayos descritos, un estudio comparativo de diferentes modelos de elementos finitos simulando los ensayos. Se comparan tanto los resultados aportados por cada modelo como los tiempos de cálculo. Por último, se presentan tres aplicaciones diferentes donde se ha aplicado este procedimiento de estudio. La primera aplicación consiste en la comparación de la resistencia mecánica de obleas de silicio en función del método de crecimiento del lingote. La resistencia de las tradicionales obleas monocristalinas obtenidas por el método Czochralski y obleas multicristalinas es comparada con las novedosas obleas quasi-monocristalinas obtenidas por métodos de fundición. En la segunda aplicación se evalúa la profundidad de las grietas generadas en el proceso de corte del lingote en obleas. Este estudio se realiza de manera indirecta: caracterizando la resistencia de grupos de obleas sometidas a baños químicos de diferente duración. El baño químico reduce el espesor de las obleas eliminando las capas más dañadas. La resistencia de cada grupo es analizada y la comparación permite obtener la profundidad de las grietas generadas en el proceso de corte. Por último, se aplica este procedimiento a un grupo de obleas con características muy especiales: obleas preparadas para formar células de contacto posterior EWT. Estas obleas presentan miles de agujeros que las debilitan considerablemente. Se aplica el procedimiento de estudio propuesto con un grupo de estas obleas y se compara la resistencia obtenida con un grupo de referencia. Además, se propone un método simplificado de estudio basado en la aplicación de una superficie de intensificación de tensiones. ABSTRACT In this thesis, a procedure to evaluate the mechanical strength of crystalline silicon wafers is proposed and applied in different studies. The photovoltaic industry is mainly based on crystalline silicon modules. These modules are composed of solar cells which are based on silicon wafers. Regarding the cost reduction of solar modules, a clear tendency to use thinner wafers has been observed during last years. Since the stiffness varies with thickness, the manipulation techniques need to be modified in order to guarantee a low breakage rate. To this end, the mechanical strength has to be characterized correctly. In the first part of the thesis, silicon wafers are described including the different ways to produce them and the mechanical properties of interest. The influence of the crystallographic structure in the strength and the behaviour (the anisotropy of the silicon crystal) is shown. In addition, a method to characterize the mechanical strength is proposed. This probabilistic procedure is based on methods to characterize brittle materials. The strength is characterized by the values of the three parameters of the Weibull cumulative distribution function (cdf). The proposed method requires carrying out several tests, to simulate them through Finite Element models and an iterative algorithm in order to estimate the parameters of the Weibull cdf. In the second part of the thesis, the different types of test that are usually employed with these samples are described. Moreover, different Finite Element models for the simulation of each test are compared regarding the information supplied by each model and the calculation times. Finally, the method of characterization is applied to three examples of practical applications. The first application consists in the comparison of the mechanical strength of silicon wafers depending on the ingot growth method. The conventional monocrystalline wafers based on the Czochralski method and the multicrystalline ones are compared with the new quasi-monocrystalline substrates. The second application is related to the estimation of the crack length caused by the drilling process. An indirect way is used to this end: several sets of silicon wafers are subjected to chemical etchings of different duration. The etching procedure reduces the thickness of the wafers removing the most damaged layers. The strength of each set is obtained by means of the proposed method and the comparison permits to estimate the crack length. At last, the procedure is applied to determine the strength of wafers used for the design of back-contact cells of type ETW. These samples are drilled in a first step resulting in silicon wafers with thousands of tiny holes. The strength of the drilled wafers is obtained and compared with the one of a standard set without holes. Moreover, a simplified approach based on a stress intensification surface is proposed.

Review and Comparison of Step-Up Transformerless Topologies for Photovoltaic AC-Module Application

This paper presents a comprehensive review of stepup single-phase non-isolated inverters suitable for ac-module applications. In order to compare the most feasible solutions of the reviewed topologies, a benchmark is set. This benchmark is based on a typical ac-module application considering the requirements for the solar panels and the grid. The selected solutions are designed and simulated complying with the benchmark obtaining passive and semiconductor components ratings in order to perform a comparison in terms of size and cost. A discussion of the analyzed topologies regarding the obtained ratings as well as ground currents is presented. Recommendations for topological solutions complying with the application benchmark are provided.

Deriving the full-reducing Krivine machine from the small-step operational semantics of normal order

We derive by program transformation Pierre Crégut s full-reducing Krivine machine KN from the structural operational semantics of the normal order reduction strategy in a closure-converted pure lambda calculus. We thus establish the correspondence between the strategy and the machine, and showcase our technique for deriving full-reducing abstract machines. Actually, the machine we obtain is a slightly optimised version that can work with open terms and may be used in implementations of proof assistants.

Moiré-Fourier deflectometry for local heat transfer measurement over a backward-facing step

This paper explores the possibility of using the Moire-Fourier deflectometry for measuring the local heat transfer coefficient inside small confined flows (micro-channels) and their relevance for checking theoretical models. This optical technique, supplemented with a digital image processing method of fringes, is applied for studying the local heat transfer over a backward facing step. The experimental results are compared with numerical results obtained from a commercial code, which has been contrasted with relevant solutions from the literature and bulk fluid temperature measurements at the inlet and outlet sections. In order to show the possibilities of the experimental technique, the influence of assuming an adiabatic wall on the numerical heat-transfer model is examined and the degree of agreement is discussed. As a result, the paper shows that the proposed Moiré-Fourier technique is a simple experimental setup suitable for temperature measurements with an accuracy similar to the thermocouples but with a spatial resolution near 0.01 mm.Moiré-Fourier deflectometry for local heat transfer measurement over a backward-facing step

Deep reactive ion etching of auxetic structures: present capabilities and challenges

Auxetic materials (or metamaterials) have negative Poisson ratios (NPR) and display the unexpected properties of lateral expansion when stretched, and equal and opposing densification when compressed. Such auxetic materials are being used more frequently in the development of novel products, especially in the fields of intelligent expandable actuators, shape-morphing structures, and minimally invasive implantable devices. Although several micromanufacturing technologies have already been applied to the development of auxetic materials and devices, additional precision is needed to take full advantage of their special mechanical properties. In this study, we present a very promising approach for the development of auxetic materials and devices based on the use of deep reactive ion etching (DRIE). The process stands out for its precision and its potential applications to mass production. To our knowledge, it represents the first time this technology has been applied to the manufacture of auxetic materials with nanometric details. We take into account the present capabilities and challenges linked to the use of DRIE in the development of auxetic materials and auxetic-based devices.

Effect of field damping layer on two step absorption of quantum dots solar cells

Multi-stacked InAs/AlGaAs quantum dot solar cells (QDSCs) introduced with field damping layers (FDL) which sustain the junction built-in potential have been studied. Without an external bias condition, the external quantum efficiency (EQE) of QD layers are reduced by introducing the thick FDL, because the carrier escape due to built-in electric field was suppressed. On the other hand, the photocurrent production due to two-step absorption is increased by the formation of flat-band QD structure for QDSC with thick FDL.

Multifunctional core–shell Co–SiO2 nanowires via electrodeposition and sol–gel techniques

In this work, we propose a new strategy for the synthesis of multifunctional nanowires using a combination of sol–gel and electrodeposition techniques, based on a two-step procedure. First of all, nanotubes of SiO2 are synthesized via a sol–gel technique using polycarbonate membranes as templates. Homogenous nanotubes are obtained after centrifugation and thermal annealing. Afterwards, a ferromagnetic cobalt core is grown using potentiostatic electrodeposition. Finally, the core–shell Co–SiO2 nanowires are released by dissolving the template using wet-etching. These nanodevices can be used for many detection and sensing purposes. As a proof of concept, we have developed a pH nanosensor by including a pH-sensitive organic dye in the SiO2 shell. The sensing principle is based on the optical response of the organic dye towards pH when added to a solution. The magnetic core allows the recovery of the nanosensors after use. These nanowires can therefore be used as recoverable pH nanosensors. By changing the dye molecule to another molecule or receptor, the procedure described in the paper can be used to synthesize nanodevices for many different applications.