On the Use of a 3-D Fundamental Solution for Axisymmetric Steady-State Dynamic Problems

The use of 3-D fundamental solution is some axisymmetric problems is straightforward. The resulting algorithms seem to work better than the usual ones (at least for static solutions) and for dynamic cases, than those presented in the previous paragraph. The robustness of the method allows the computations for very high and very low frequencies without any noticeable difficulty.

Steady-state thermal analysis of an innovative receiver for linear Fresnel reflectors

The study of the performance of an innovative receiver for linear Fresnel reflectors is carried out in this paper, and the results are analyzed with a physics perspective of the process. The receiver consists of a bundle of tubes parallel to the mirror arrays, resulting on a smaller cross section for the same receiver width as the number of tubes increases, due to the diminution of their diameter. This implies higher heat carrier fluid speeds, and thus, a more effective heat transfer process, although it conveys higher pumping power as well. Mass flow is optimized for different tubes diameters, different impinging radiation intensities and different fluid inlet temperatures. It is found that the best receiver design, namely the tubes diameter that maximizes the exergetic efficiency for given working conditions, is similar for the cases studied. There is a range of tubes diameters that imply similar efficiencies, which can drive to capital cost reduction thanks to the flexibility of design. In addition, the length of the receiver is also optimized, and it is observed that the optimal length is similar for the working conditions considered. As a result of this study, it is found that this innovative receiver provides an optimum design for the whole day, even though impinging radiation intensity varies notably. Thermal features of this type of receiver could be the base of a new generation of concentrated solar power plants with a great potential for cost reduction, because of the simplicity of the system and the lower weigh of the components, plus the flexibility of using the receiver tubes for different streams of the heat carrier fluid.

Analysis of microscopic magnitudes of radiative blast waves launched in xenon clusters with collisional-radiative steady-state simulations

Radiative shock waves play a pivotal role in the transport energy into the stellar medium. This fact has led to many efforts to scale the astrophysical phenomena to accessible laboratory conditions and their study has been highlighted as an area requiring further experimental investigations. Low density material with high atomic mass is suitable to achieve radiative regime, and, therefore, low density xenon gas is commonly used for the medium in which the radiative shocks such as radiative blast waves propagate. In this work, by means of collisional-radiative steady-state calculations, a characterization and an analysis of microscopic magnitudes of laboratory blast waves launched in xenon clusters are made. Thus, for example, the average ionization, the charge state distribution, the cooling time or photon mean free paths are studied. Furthermore, for a particular experiment, the effects of the self-absorption and self-emission in the specific intensity emitted by the shock front and that is going through the radiative precursor are investigated. Finally, for that experiment, since the electron temperature is not measured experimentally, an estimation of this magnitude is made both for the shock shell and the radiative precursor.

Steady state analysis of a storage integrated solar thermophotovoltaic (SISTPV) system

This paper presents the theoretical analysis of a storage integrated solar thermophotovoltaic (SISTPV) system operating in steady state. These systems combine thermophotovoltaic (TPV) technology and high temperature thermal storage phase-change materials (PCM) in the same unit, providing a great potential in terms of efficiency, cost reduction and storage energy density. The main attraction in the proposed system is its simplicity and modularity compared to conventional Concentrated Solar Power (CSP) technologies. This is mainly due to the absence of moving parts. In this paper we analyze the use of Silicon as the phase change material (PCM). Silicon is an excellent candidate because of its high melting point (1680 K) and its very high latent heat of fusion of 1800 kJ/kg, which is about ten times greater than the conventional PCMs like molten salts. For a simple system configuration, we have demonstrated that overall conversion efficiencies up to ?35% are approachable. Although higher efficiencies are expected by incorporating more advanced devices like multijunction TPV cells, narrow band selective emitters or adopting near-field TPV configurations as well as by enhancing the convective/conductive heat transfer within the PCM. In this paper, we also discuss about the optimum system configurations and provide the general guidelines for designing these systems. Preliminary estimates of night time operations indicate it is possible to achieve over 10 h of operation with a relatively small quantity of Silicon.

Deviations of cup anemometer rotational speed measurements due to steady state harmonic accelerations of the rotor

The measurement deviations of cup anemometers are studied by analyzing the rotational speed of the rotor at steady state (constant wind speed). The differences of the measured rotational speed with respect to the averaged one based on complete turns of the rotor are produced by the harmonic terms of the rotational speed. Cup anemometer sampling periods include a certain number of complete turns of the rotor, plus one incomplete turn, the residuals from the harmonic terms integration within that incomplete turn (as part of the averaging process) being responsible for the mentioned deviations. The errors on the rotational speed due to the harmonic terms are studied analytically and then experimentally, with data from more than 500 calibrations performed on commercial anemometers.

Assessment of CTF boiling transition and critical heat flux modeling capabilities using the OECD/NRC BFBT and PSBT benchmark databases

The need to refine models for best-estimate calculations, based on good-quality experimental data, has been expressed in many recent meetings in the field of nuclear applications. The modeling needs arising in this respect should not be limited to the currently available macroscopic methods but should be extended to next-generation analysis techniques that focus on more microscopic processes. One of the most valuable databases identified for the thermalhydraulics modeling was developed by the Nuclear Power Engineering Corporation (NUPEC), Japan. From 1987 to 1995, NUPEC performed steady-state and transient critical power and departure from nucleate boiling (DNB) test series based on the equivalent full-size mock-ups. Considering the reliability not only of the measured data, but also other relevant parameters such as the system pressure, inlet sub-cooling and rod surface temperature, these test series supplied the first substantial database for the development of truly mechanistic and consistent models for boiling transition and critical heat flux. Over the last few years the Pennsylvania State University (PSU) under the sponsorship of the U.S. Nuclear Regulatory Commission (NRC) has prepared, organized, conducted and summarized the OECD/NRC Full-size Fine-mesh Bundle Tests (BFBT) Benchmark. The international benchmark activities have been conducted in cooperation with the Nuclear Energy Agency/Organization for Economic Co-operation and Development (NEA/OECD) and Japan Nuclear Energy Safety (JNES) organization, Japan. Consequently, the JNES has made available the Boiling Water Reactor (BWR) NUPEC database for the purposes of the benchmark. Based on the success of the OECD/NRC BFBT benchmark the JNES has decided to release also the data based on the NUPEC Pressurized Water Reactor (PWR) subchannel and bundle tests for another follow-up international benchmark entitled OECD/NRC PWR Subchannel and Bundle Tests (PSBT) benchmark. This paper presents an application of the joint Penn State University/Technical University of Madrid (UPM) version of the well-known subchannel code COBRA-TF, namely CTF, to the critical power and departure from nucleate boiling (DNB) exercises of the OECD/NRC BFBT and PSBT benchmarks

Domestic hot water consumption vs. solar thermal energy storage: the optimum size of the storage tank

Many efforts have been made in order to adequate the production of a solar thermal collector field to the consumption of domestic hot water of the inhabitants of a building. In that sense, much has been achieved in different domains: research agencies, government policies and manufacturers. However, most of the design rules of the solar plants are based on steady state models, whereas solar irradiance, consumption and thermal accumulation are inherently transient processes. As a result of this lack of physical accuracy, thermal storage tanks are sometimes left to be as large as the designer decides without any aforementioned precise recommendation. This can be a problem if solar thermal systems are meant to be implemented in nowadays buildings, where there is a shortage of space. In addition to that, an excessive storage volume could not result more efficient in many residential applications, but costly, extreme in space consumption and in some cases too heavy. A proprietary transient simulation program has been developed and validated with a detailed measurement campaign in an experimental facility. In situ environmental data have been obtained through a whole year of operation. They have been gathered at intervals of 10 min for a solar plant of 50 m2 with a storage tank of 3 m3, including the equipment for domestic hot water production of a typical apartment building. This program has been used to obtain the design and dimensioning criteria of DHW solar plants under daily transient conditions throughout a year and more specifically the size of the storage tank for a multi storey apartment building. Comparison of the simulation results with the current Spanish regulation applicable, “Código Técnico de la Edificación” (CTE 2006), offers fruitful details and establishes solar facilities dimensioning criteria.

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented.

Modelización de las propiedades radiativas e interacción de láseres ultraintensos con la materia

Desde el año 2004 el código ARWEN ha sido utilizado con éxito para simular y diseñar experimentos relacionados con blancos para fusión por confinamiento inercial [146], astrofísica de laboratorio [145], plasmas como amplificadores de láseres de rayos X [107] o plasmas creados por láser para la medición de espectros de transmisión. Para la realización de estas simulaciones es necesario, además de métodos de alto orden precisos y que presenten buenas propiedades conservativas, conocer ciertas propiedades de los plasmas. En el caso de la fluidodinámica y la conducción electrónica necesitaremos conocer la ecuación de estado [94, 49, 36], y para el transporte de la radiación será preciso disponer de los datos de absorción y emisión [104, 95, 40]. Hasta el año 2009 ARWEN dependía de códigos externos para la generación de estas tablas de opacidad, careciendo de control sobre los métodos empleados para su generación. Además estos códigos asumían equilibrio local termodinámico (LTE), limitando su validez a rangos de alta densidad y baja temperatura. En el marco de esta tesis se ha desarrollado el código BIGBART para la generación de tablas detalladas de opacidad y emisividad para su uso en el módulo de transporte de radiación. De esta forma el grupo dispondrá de su propia herramienta de generación de propiedades radiativas. El código desarrollado es capaz de tratar plasmas en estado fuera de equilibrio (non-LTE) mediante el modelo colisional-radiativo, extendiendo así el rango de validez de las tablas generadas. El trabajo desarrollado para implementar un código LTE/non-LTE estacionario es el siguiente Cálculo de estructura y datos atómicos. Se ha acoplado en código FAC a BIGBART, incorporando la capacidad para generar potenciales atómicos para una configuración y el cálculo de funciones de onda de electrones en orbitales ligados y libres. Aproximaciones y métodos para la obtención de tasas y secciones eficaces de procesos. Se han incluido y programado los modelos implementados en FAC para el cálculo de secciones eficaces de fotoionización, y tasas de decaimiento de emisión espontánea y autoionización. Además se ha incluido el modelo Plane-Wave Born (PWBA) para el cálculo de las secciones eficaces de ionización y excitación colisional. Modelos para la obtención de la distribución de estados iónicos dentro del plasma. Se ha programado un solver LTE basado en la ecuación de Saha-Boltzmann con efectos de ionización por presión debida a los iones adyacentes. También se ha implementado un modelo non-LTE colisionalradiativo para la resolución del sistema de ecuaciones que nos permite obtener la densidad de estados iónicos fuera de equilibrio. Modelo non-LTE RADIOM. Se ha implementado el modelo RADIOM para aproximar efectos de no-equilibrio mediante cálculos LTE a una temperatura equivalente, menor o igual que la temperatura electrónica real. Cálculo de las propiedades espectrales de absorción y emisión. Se han implementado los modelos para el cálculo de los perfiles espectrales de absorción y emisión para procesos entre niveles ligados, ligado-libre y librelibre. Aprovechando el trabajo realizado en este sentido, durante el transcurso de esta tesis se amplió el código BIGBART para tratar problemas con dependencia temporal. La extensión para tratar este tipo de problemas se orientó a la simulación numérica de la interacción de láseres ultra intensos en el rango XUV/rayos X. Para ello, además de adaptar el modelo non-LTE colisionalradiativo se incluyeron procesos adicionales asociados a la interacción de la materia con fotones altamente energéticos. También se han incluido modelos para el cálculo de las propiedades ópticas, y por ende las propiedades dieléctricas de la materia irradiada, de gran interés en algunas aplicaciones novedosas de estos láseres intensos. Debido a la naturaleza fuertemente fuera de equilibrio en la interacción de fotones de alta energía con la materia, se incluyó el tratamiento de la distribución de electrones libres fuera de equilibrio en la aproximación de Fokker-Planck, tanto para condiciones degeneradas como no degeneradas. El trabajo desarrollado en el código non-LTE con dependencia temporal es el siguiente Procesos asociados a láseres intensos XUV/rayos X. Se ha implementado el cálculo de procesos radiativos estimulados de absorción y emisión por el láser. También se han incluido procesos asociados a la creación de vacantes en capas internas electrónicas (Shake), además de doble autoionización y doble fotoionización. Cálculo de propiedades ópticas y dieléctricas en blancos sólidos. Se ha implementado un modelo para la absorción por bremsstrahlung inverso en blancos en estado sólido. Con el coeficiente de extinción debido a procesos de fotoabsorción resonante, fotoionización y bremsstrahlung inverso se obtiene el ´ındice de refracción mediante la relación de Kronig-Kramers. Electrones fuera de equilibrio. Se ha tratado la evolución de la distribución de electrones, cuando no está justificado asumir que es Maxwelliana o de Fermi-Dirac, mediante la aproximación de Fokker-Planck para la colisión entre electrones libres. En la resolución de la ecuación de Fokker-Planck se han incluido los procesos inelásticos por colisiones con iones y términos fuente por interacción con el láser y otros procesos. ABSTRACT Since 2004 the ARWEN code has been successfully used to simulate and design targets for inertial confinement fusion experiments [146], laboratory astrophysics [145], plasmas as X-ray lasers amplifiers [107] or laser created plasmas for measuring transmission spectra. To perform these simulations it is necessary, in addition to high order precise methods with good conservative properties, to know certain properties of plasmas. For fluid dynamic and electronic conduction we need to know the equation of state [94, 49, 36], and for radiation transport it will be necessary to have the data of the absorption and emission [104, 95, 40]. Until 2009 ARWEN depended on external codes to generate these opacity tables, lacking of control over the methods used for their generation. Besides, these codes assumed local thermodynamic equilibrium (LTE), limiting their validity ranges to high densities and low temperatures. As part of this thesis it has been developed the BIGBART code for generating detailed opacity and emissivity tables for use in the radiation transport module. This group will have its own tool for the generation of radiative properties. The developed code is capable of treating plasmas out of equilibrium (non-LTE) by means of a collisional-radiative model, extending the range of validity of the generated tables. The work to implement an LTE/non-LTE steady-state code is as follows Calculation of structure and atomic data. the FAC code was coupled to BIGBART, incorporating the ability to generate atomic potentials for calculating configuration wave functions for bound and free electrons. Approaches and methods for obtaining cross sections and processes rates. We have included and reprogrammed in Fortran the models implemented in FAC for calculation of photoionization cross sections and decay rates of spontaneous emission and autoionization. We also included the Plane- Wave Born (PWBA) model to calculate the cross sections of ionization and collisional excitation. Models for the obtention of the distribution of ionic states within the plasma. We programmed a LTE solver based on the Saha-Boltzmann equation with pressure ionization effects due to adjacent ions. It has also been implemented a non-LTE collisional-radiative model for solving the system of equations that allows us to obtain the density of ionic states out of equilibrium. Non-LTE RADIOM model. We have implemented the non-LTE RADIOM model to approximate non-equilibrium effects with LTE data at an equivalent temperature, lower or equal to the actual electronic temperature. Calculation of the spectral absorption and emission properties. Models have been implemented for the calculation of the spectral profiles of absorption and emission processes between bound levels, free-bound and free-free. Taking advantage of the work done in this direction throughout the course of this thesis the code BIGBART was extended to treat time-dependent problems. The extension to treat such problems is oriented to the numerical simulation of the interaction of ultra intense lasers in the XUV/X-ray range. For this range, in addition to adapting the non-LTE collisional-radiative model, additional processes associated with the interaction of matter with high energy photons. We also included models for calculation of the optical properties, and therefore the dielectric properties of the irradiated material, of great interest in some novel applications of these intense lasers. Due to the strong non-equilibrium nature of the interaction of high energy photons with matter, we included the treatment of the distribution of free electrons out of equilibrium in the Fokker-Planck approximation for both degenerate and non-degenerate conditions. The work in the non-LTE time-dependent code is as follows Processes associated with intense XUV/X-ray lasers. We have implemented the calculation of stimulated radiative processes in absorption and emission. Also we included processes associated with the creation of electronic vacancies in inner shells (Shake), double autoionization and double photoionization. Calculation of optical and dielectric properties in solid targets. We have implemented a model for inverse bremsstrahlung absorption in solid targets. With the extinction coefficient from resonant photoabsorption, photoionization and inverse bremsstrahlung the refractive index is obtained by the Kramers-Kronig relation. Electrons out of equilibrium. We treat the evolution of the electron distribution, when it is not justified to assume a Maxwellian or Fermi-Dirac distribution, by the Fokker-Planck approximation for collisions between electrons. When solving the Fokker-Planck equation we included inelastic collision processes with ions and source terms by interaction with the laser and other processes.

Estudio de la influencia de la relación C/N en la desnitrificación y metanogénesis de aguas residuales en un reactor anaeróbico de lecho fluidizado inverso

La nitrificación-desnitrificación es el proceso biológico tradicional para la remoción de nitrógeno de las aguas residuales (Ruiz G. et al., 2006a), siendo fundamental ya que contribuye a controlar la eutroficación de los cuerpos receptores. Debido al deterioro que sobre la disponibilidad de los recursos han ejercido las actividades antropogénicas, es necesario orientar el tratamiento de las aguas residuales hacia tecnologías que ofrezcan el mayor grado de sustentabilidad, planteando innovaciones en el tratamiento. El presente proyecto de tesis doctoral versa sobre el estudio de la influencia de la relación C/N en la desnitrificación y metanogénesis de aguas residuales urbanas en un reactor anaeróbico de lecho fluidizado inverso (RLFI). Previamente a la realización de las pruebas experimentales de variación de la relación C/N, se llevó a cabo la etapa de arranque del RLFI la cual se inició en modo batch, favoreciendo la formación y adhesión de biopelícula al medio de soporte utilizado (Extendosphere). Después, sobrevino la operación en modo continuo desde una carga volumétrica aplicada (CVA) de 0.5 g DQOs/L⋅d hasta alcanzar 4 g DQOs/L⋅d, carga volumétrica a la cual se logró la plena estabilización del reactor, siendo la alta variabilidad de la concentración de DQOs en el agua residual urbana de alimentación, la principal problemática que ocasionó retrasos en la estabilidad del reactor. A una CVA de 4 g DQOs/L⋅d en estado estacionario, el valor mínimo de eficiencia de remoción de DQOs fue del 32.36% y el máximo de 66.99%. En estas condiciones el porcentaje de metano presente en el biogás producido tuvo un valor medio de 85.57 ± 2.93%, siendo un valor alto comparado con otros porcentajes de metano encontrados en la digestión anaerobia de aguas residuales urbanas. El YCH4 tuvo un valor medio de 0.316 ± 0.110 LCH4/g DQOrem⋅día. Los porcentajes de metanización variaron en el rango de 20.50 a 100%, registrándose un valor medio de 73.42 ± 25.63%. La considerable variabilidad en el porcentaje de metanización se debió principalmente a que se presentaron eventos de lavado de soporte colonizado, lo cual propició que las actividades metabólicas fueran orientadas hacia formación de biopelícula (anabolismo) en vez de estar dirigidas hacia producción de metano (catabolismo). En relación a los ensayos con variación de la relación C/N, se manejaron relaciones DQOs/N-NO3 en el rango de 1.65 a 21.1 g DQOs/g N-NO3. La tasa de remoción anaerobia de DQOs se incrementó con la concentración de sustrato en una relación casi lineal, ajustándose a una cinética de primer orden, lo que regularmente se presenta a concentraciones bajas de sustrato. La eficiencia del proceso de desnitrificación fue por lo regular alta, incrementándose ligeramente con la concentración de DQOs en el influente, con valores en el rango de 73.8 a 99.1%. Por otra parte, la tasa de remoción por metanogénesis se incrementó con la concentración relativa de sustrato (es decir, a mayores relaciones DQOs/N-NO3), siendo más sensitiva la metanogénesis a la concentración relativa de sustrato que la desnitrificación. Conforme aumentó la relación DQOs/N-NO3, la desnitrificación, de ser la ruta metabólica principal de utilización de la materia orgánica (comparada con la metanización), empezó a combinarse con la metanización. De manera evidente, a las relaciones DQOs/N-NO3 probadas, se manifestaron más las actividades desnitrificantes, quedando reflejadas por el alto porcentaje de utilización de la DQOs removida hacia la desnitrificación. La relación experimental DQOs/N-NO3 a la cual se pudiera haber cumplido con el requerimiento de materia orgánica (en términos de DQOs) para la desnitrificación de nitratos en las aguas residuales urbanas tratadas resultó aproximadamente ser igual a 7.1 g DQOs/g N-NO3. A una CVA de 4 g DQOs/L⋅d, se obtuvo un diámetro promedio máximo de soporte colonizado igual a 266.106 ± 69.279 μm aunque, hay que indicarlo, se presentaron fluctuaciones, las cuales se reflejaron también en el espesor de la biopelícula, el cual tuvo un valor máximo de 50.099 μm y un valor promedio de 37.294 ± 11.199 μm. Estas fluctuaciones pudieron deberse a la existencia de corrientes preferenciales dentro del reactor, las cuales no permitieron un acceso equitativo del sustrato a todo el lecho. Nitrification-denitrification is the traditional biological process for nitrogen removal from wastewaters (Ruiz G. et al., 2006a), being fundamental since it contributes to control the eutrophication of the receiving waters. Due to the deterioration that on the availability of the aquatic resources the anthropogenic activities have exerted, it is necessary to orient the treatment of wastewaters towards technologies that offer the greater degree of sustainability, raising innovations in the treatment. This work studied the influence of C/N ratio on denitrification and methanogenesis of urban wastewaters in an inverse fluidized bed reactor (IFBR). Previously to the accomplishment of the experimental tests with variation of C/N ratio, the start up of the IFBR was carried out in batch way, encouraging the formation and adhesion of biofilm to Extendosphere, which it was used as support. The operation in continuous way carried out from an organic loading rate (OLR) of 0.5 g CODs/L ∙ d to 4 g CODs/L ∙ d, when the steady-state was reached. The high variability of the CODs of the urban wastewaters caused delays in the stability of the reactor. Once stationary state was reached, the removal efficiency of CODs ranged from 32.36 to 66.99% to 4 g CODs/L ∙ d. In these conditions the percentage of methane in produced biogas had an average value of 85.57 ± 2.93%, being a high value compared with other studies treating anaerobically urban wastewaters. The YCH4 had an average value of 0.316 ± 0.110 LCH4/g CODrem ∙ d. The percentage of methanisation ranged from 20.50 to 100%, with an average value of 73.42 ± 25.63%. The considerable variability in the methanisation percentage occurred mainly due events of wash-out of colonized support, which caused that the metabolic activities were oriented towards formation of biofilm (anabolism) instead of methane production (catabolism). Concerning the tests with variation of C/N ratio, CODs/NO3-N ratios from 1.65 to 21.1 g CODs/g NO3-N were proved. The CODs anaerobic removal rate increased with the substrate concentration in an almost linear relation, adjusting to a kinetic of first order, which regularly appears to low concentrations of substrate. Efficiency of the denitrification process was regularly high, and it increased slightly with the CODs concentration in the influent, ranging from 73.8 to 99.1%. On the other hand, the CODs removal rate by methanogenesis increased with the substrate relative concentration (e.g., to greater CODs/NO3-N ratios), being more sensitive the methanogenesis to the substrate relative concentration that the denitrification. When the CODs/NO3-N ratio increased, the denitrification, of being the main metabolic route of use of the organic matter (compared with the methanogenesis), began to be combined with the methanogenesis. Definitively, to the proven CODs/NO3-N ratios the denitrification processes were more pronounced, being reflected by the high percentage of use of the removed CODs towards denitrification. The experimental CODs/NO3-N ratio to which it was possible to have been fulfilled the requirement of organic matter (in terms of CODs) for the denitrification of nitrates in urban wastewaters turned out to be approximately 7.1 g CODs/g NO3-N. It was obtained a maximum average diameter of colonized support of 266.106 ± 69.279 μm to 4 g CODs/L ∙ d, although it is necessary to indicate that appeared fluctuations in the thickness of biofilm, which had a maximum value of 50.099 μm and an average value of 37.294 ± 11.199 μm. These fluctuations could be due to the existence of preferential currents within the reactor, which did not allow an equitable access of the substrate to all the bed.