Power system stability of a small sized isolated network supplied by a combined wind-pumped storage generation system: a case study in the Canary Islands

Massive integration of renewable energy sources in electrical power systems of remote islands is a subject of current interest. The increasing cost of fossil fuels, transport costs to isolated sites and environmental concerns constitute a serious drawback to the use of conventional fossil fuel plants. In a weak electrical grid, as it is typical on an island, if a large amount of conventional generation is substituted by renewable energy sources, power system safety and stability can be compromised, in the case of large grid disturbances. In this work, a model for transient stability analysis of an isolated electrical grid exclusively fed from a combination of renewable energy sources has been studied. This new generation model will be installed in El Hierro Island, in Spain. Additionally, an operation strategy to coordinate the generation units (wind, hydro) is also established. Attention is given to the assessment of inertial energy and reactive current to guarantee power system stability against large disturbances. The effectiveness of the proposed strategy is shown by means of simulation results.

Stability of vacancy clusters in FeCr alloys: A study of the Cr concentration dependence

Fe–Cr based alloys are the leading structural material candidates in the design of next generation reactors due to their high resistance to swelling and corrosion. Despite these good properties there are others, such as embrittlement, which require a higher level of understanding in order to improve aspects such as safety or lifetime of the reactors. The addition of Cr improves the behavior of the steels under irradiation, but not in a monotonic way. Therefore, understanding the changes in the Fe–Cr based alloys microstructure induced by irradiation and the role played by the alloying element (Cr) is needed in order to predict the response of these materials under the extreme conditions they are going to support. In this work we perform a study of the effect of Cr concentration in a bcc Fe–Cr matrix on formation and binding energies of vacancy clusters up to 5 units. The dependence of the calculated formation and binding energy is investigated with two empirical interatomic potentials specially developed to study radiation damage in Fe–Cr alloys. Results are very similar for both potentials showing an increase of the defect stability with the cluster size and no real dependence on Cr concentration for the binding energy.

Safety and operability of small fishing vessels: study of a series of stability-related accidents

The intact stability of five small Spanish fishing vessels with ages between 3 and 8 years old which sunk in stability related accidents between 2004 and 2007 is compared to the stability of the fishing vessels which were retired from service to build those. The seakeeping performance of both sets of vessels is also compared. The differences found between the results obtained by the two methods have been analyzed. The suitability of seakeeping methods to assess stability performance is discussed.

Fishing effort control regulations influence on stability, safety and operability of small fishing vessels: study of a series of stability related accidents occurred in Spain between 2004 and 2007

Entre los años 2004 y 2007 se hundieron por problemas de estabilidad cinco pesqueros españoles de pequeña eslora, de características parecidas, de relativamente poca edad, que habían sido construidos en un intervalo de pocos años. La mayoría de los tripulantes de esos pesqueros fallecieron o desaparecieron en esos accidentes. Este conjunto de accidentes tuvo bastante repercusión social y mediática. Entre ingenieros navales y marinos del sector de la pesca se relacionó estos accidentes con los condicionantes a los diseños de los pesqueros impuestos por la normativa de control de esfuerzo pesquero. Los accidentes fueron investigados y publicados sus correspondientes informes; en ellos no se exploró esta supuesta relación. Esta tesis pretende investigar la relación entre esos accidentes y los cambios de la normativa de esfuerzo pesquero. En la introducción se expone la normativa de control de esfuerzo pesquero analizada, se presentan datos sobre la estructura de la flota pesquera en España y su accidentalidad, y se detallan los criterios de estabilidad manejados durante el trabajo, explicando su relación con la seguridad de los pesqueros. Seguidamente se realiza un análisis estadístico de la siniestralidad en el sector de la pesca para establecer si el conjunto de accidentes estudiados supone una anomalía, o si por el contrario el conjunto de estos accidentes no es relevante desde el punto de vista estadístico. Se analiza la siniestralidad a partir de diversas bases de datos de buques pesqueros en España y se concluye que el conjunto de accidentes estudiados supone una anomalía estadística, ya que la probabilidad de ocurrencia de los cinco sucesos es muy baja considerando la frecuencia estimada de pérdidas de buques por estabilidad en el subsector de la flota pesquera en el que se encuadran los cinco buques perdidos. A continuación el trabajo se centra en la comparación de los buques accidentados con los buques pesqueros dados de baja para construir aquellos, según exige la normativa de control de esfuerzo pesquero; a estos últimos buques nos referiremos como “predecesores” de los buques accidentados. Se comparan las dimensiones principales de cada buque y de su predecesor, resultando que los buques accidentados comparten características de diseño comunes que son sensiblemente diferentes en los buques predecesores, y enlazando dichas características de diseño con los requisitos de la nueva normativa de control del esfuerzo pesquero bajo la que se construyeron estos barcos. Ello permite establecer una relación entre los accidentes y el mencionado cambio normativo. A continuación se compara el margen con que se cumplían los criterios reglamentarios de estabilidad entre los buques accidentados y los predecesores, encontrándose que en cuatro de los cinco casos los predecesores cumplían los criterios de estabilidad con mayor holgura que los buques accidentados. Los resultados obtenidos en este punto permiten establecer una relación entre el cambio de normativa de esfuerzo pesquero y la estabilidad de los buques. Los cinco buques accidentados cumplían con los criterios reglamentarios de estabilidad en vigor, lo que cuestiona la relación entre esos criterios y la seguridad. Por ello se extiende la comparativa entre pesqueros a dos nuevos campos relacionados con la estabilidad y la seguridad delos buques: • Movimientos a bordo (operatividad del buque), y • Criterios de estabilidad en condiciones meteorológicas adversas El estudio de la operatividad muestra que los buques accidentados tenían, en general, una mayor operatividad que sus predecesores, contrariamente a lo que sucedía con el cumplimiento de los criterios reglamentarios de estabilidad. Por último, se comprueba el desempeño de los diez buques en dos criterios específicos de estabilidad en caso de mal tiempo: el criterio IMO de viento y balance intenso, y un criterio de estabilidad de nueva generación, incluyendo la contribución original del autor de considerar agua en cubierta. Las tendencias observadas en estas dos comparativas son opuestas, lo que permite cuestionar la validez del último criterio sin un control exhaustivo de los parámetros de su formulación, poniendo de manifiesto la necesidad de más investigaciones sobre ese criterio antes de su adopción para uso regulatorio. El conjunto de estos resultados permite obtener una serie de conclusiones en la comparativa entre ambos conjuntos de buques pesqueros. Si bien los resultados de este trabajo no muestran que la aprobación de la nueva normativa de esfuerzo pesquero haya significado una merma general de seguridad en sectores enteros de la flota pesquera, sí se concluye que permitió que algunos diseños de buques pesqueros, posiblemente en busca de la mayor eficiencia compatible con dicha normativa, quedaran con una estabilidad precaria, poniendo de manifiesto que la relación entre seguridad y criterios de estabilidad no es unívoca, y la necesidad de que éstos evolucionen y se adapten a los nuevos diseños de buques pesqueros para continuar garantizando su seguridad. También se concluye que la estabilidad es un aspecto transversal del diseño de los buques, por lo que cualquier reforma normativa que afecte al diseño de los pesqueros o su forma de operar debería estar sujeta a evaluación por parte de las autoridades responsables de la seguridad marítima con carácter previo a su aprobación. ABSTRACT Between 2004 and 2007 five small Spanish fishing vessels sank in stability related accidents. These vessels had similar characteristics, had relatively short age, and had been built in a period of a few years. Most crewmembers of these five vessels died or disappeared in those accidents. This set of accidents had significant social and media impact. Among naval architects and seamen of the fishing sector these accidents were related to the design constraints imposed by the fishing control effort regulations. The accidents were investigated and the official reports issued; this alleged relationship was not explored. This thesis aims to investigate the relationship between those accidents and changes in fishing effort control regulations. In the introduction, the fishing effort control regulation is exposed, data of the Spanish fishing fleet structure and its accident rates are presented, and stability criteria dealt with in this work are explained, detailing its relationship with fishing vessel safety. A statistical analysis of the accident rates in the fishing sector in Spain is performed afterwards. The objective is determining whether the set of accidents studied constitute an anomaly or, on the contrary, they are not statistically relevant. Fishing vessels accident rates is analyzed from several fishing vessel databases in Spain. It is concluded that the set of studied accidents is statistically relevant, as the probability of occurrence of the five happenings is extremely low, considering the loss rates in the subsector of the Spanish fishing fleet where the studied vessels are fitted within. From this point the thesis focuses in comparing the vessels lost and the vessels that were decommissioned to build them as required by the fishing effort control regulation; these vessels will be referred to as “predecessors” of the sunk vessels. The main dimensions between each lost vessel and her predecessor are compared, leading to the conclusion that the lost vessels share design characteristics which are sensibly different from the predecessors, and linking these design characteristics with the requirements imposed by the new fishing control effort regulations. This allows establishing a relationship between the accidents and this regulation change. Then the margin in fulfilling the regulatory stability criteria among the vessels is compared, resulting, in four of the five cases, that predecessors meet the stability criteria with greater clearance than the sunk vessels. The results obtained at this point would establish a relationship between the change of fishing effort control regulation and the stability of vessels. The five lost vessels complied with the stability criteria in force, so the relation between these criteria and safety is put in question. Consequently, the comparison among vessels is extended to other fields related to safety and stability: • Motions onboard (operability), and • Specific stability criteria in rough weather The operability study shows that the lost vessels had in general greater operability than their predecessors, just the opposite as when comparing stability criteria. Finally, performance under specific rough weather stability criteria is checked. The criteria studied are the IMO Weather Criterion, and one of the 2nd generation stability criteria under development by IMO considering in this last case the presence of water on deck, which is an original contribution by the author. The observed trends in these two cases are opposite, allowing to put into question the last criterion validity without an exhaustive control of its formulation parameters; indicating that further research might be necessary before using it for regulatory purposes. The analysis of this set of results leads to some conclusions when comparing both groups of fishing vessels. While the results obtained are not conclusive in the sense that the entry into force of a new fishing effort control in 1998 caused a generalized safety reduction in whole sectors of the Spanish fishing fleet, it can be concluded that it opened the door for some vessel designs resulting with precarious stability. This evidences that the relation between safety and stability criteria is not univocal, so stability criteria needs to evolve for adapting to new fishing vessels designs so their safety is still guaranteed. It is also concluded that stability is a transversal aspect to ship design and operability, implying that any legislative reform affecting ship design or operating modes should be subjected to assessing by the authorities responsible for marine safety before being adopted.

Validation Study of the Use of Matlab/Simulink Synchronous-Machine Block for Accurate Power-Plant Stability Studies

This paper presents results of the validity study of the use of MATLAB/Simulink synchronous-machine block for power-system stability studies. Firstly, the waveforms of the theoretical synchronous-generator short-circuit currents are described. Thereafter, the comparison between the currents obtained through the simulation model in the sudden short-circuit test, are compared to the theoretical ones. Finally, the factory tests of two commercial generating units are compared to the response of the synchronous generator simulation block during sudden short-circuit, set with the same real data, with satisfactory results. This results show the validity of the use of this generator block for power plant simulation.

Study of the foundations, bearing soil and stability of the minaret-tower of Cordobas Mosque

This research in Cordoba's mosque tower main objective was to analyze and characterize the foundations and the underlying soil, calculating the stability of the monument as well as the settlement and deformations performed, using traditional calculation methods and also by finite elements, and to determine differences between both, as well as the stability factor of the Minaret Tower. The works done to study the soil, were drill bores and dynamic penetration tests, classification of samples by size, Atterberg limits, physical and chemical analysis, showing the typical geotechnical composition of the Guadalquivir valley: an alluvial material composed by sand, gravels and silt clays. To study the foundations, inclined bore samples were extracted with 10-65º, showing calcarenite stone ashlars and lime concrete alternating with stone and brick masonry.

An experimental study of the breakage of liquid bridges at stability limit of minimum volume

An experimental apparatus to study the breaking process of axisymmetric liquid bridges has been developed, and the breaking sequences of a large number of liquid bridge configurations at minimum-volume stability limit have been analyzed. Experimental results show that very close to the breaking moment the neck radius of the liquid bridge varies as t1/3, where t is the time to breakage, irrespective of the value of the distance between the solid disks that support the liquid column.

Analytical study of the thermal behaviour and stability of a small satellite

In this work the thermal analysis of a small satellite orbiting around the Earth has been approached by direct integration of the heat balance equations of a two-node reduced model, obtaining a linearized second order ODE problem, similar in form to the classical case of the forced vibration of a damped system. As the thermal loads (solar radiation, albedo, etc.) are harmonic, the problem is solved by means of Fourier analysis methods. Research on that field can be directly applied to the analysis of thermal problems and the results obtained are satisfactory. Working on the frequency domain streamlines the analysis, simplifies the study and facilitates the experimental testing. The transfer functions are obtained for the two-node case but the study can be extended to an n-node model.

Interstitial defects stability in FeCr alloys vs Cr concentration

Finding adequate materials to withstand the demanding conditions in the future fusion and fission reactors is a real challenge in the development of these technologies. Structural materials need to sustain high irradiation doses and temperatures that will change the microstructure over time. A better understanding of the changes produced by the irradiation will allow for a better choice of materials, ensuring a safer and reliable future power plants. High-Cr ferritic/martensitic steels head the list of structural materials due to their high resistance to swelling and corrosion. However, it is well known that these alloys present a problem of embrittlement, which could be caused by the presence of defects created by irradiation as these defects act as obstacles for dislocation motion. Therefore, the mechanical response of these materials will depend on the type of defects created during irradiation. In this work, we address a study of the effect Cr concentration has on single interstitial defect formation energies in FeCr alloys.

Clean Coal Technologies Scenario and Evaluation of Present CO2 Dwindling Initiatives to Approach Zero Emission Power Stations By Coal Combustion. Deployment Situation and Evaluation Study

In the present uncertain global context of reaching an equal social stability and steady thriving economy, power demand expected to grow and global electricity generation could nearly double from 2005 to 2030. Fossil fuels will remain a significant contribution on this energy mix up to 2050, with an expected part of around 70% of global and ca. 60% of European electricity generation. Coal will remain a key player. Hence, a direct effect on the considered CO2 emissions business-as-usual scenario is expected, forecasting three times the present CO2 concentration values up to 1,200ppm by the end of this century. Kyoto protocol was the first approach to take global responsibility onto CO2 emissions monitoring and cap targets by 2012 with reference to 1990. Some of principal CO2emitters did not ratify the reduction targets. Although USA and China spur are taking its own actions and parallel reduction measures. More efficient combustion processes comprising less fuel consuming, a significant contribution from the electricity generation sector to a CO2 dwindling concentration levels, might not be sufficient. Carbon Capture and Storage (CCS) technologies have started to gain more importance from the beginning of the decade, with research and funds coming out to drive its come in useful. After first researching projects and initial scale testing, three principal capture processes came out available today with first figures showing up to 90% CO2 removal by its standard applications in coal fired power stations. Regarding last part of CO2 reduction chain, two options could be considered worthy, reusing (EOR & EGR) and storage. The study evaluates the state of the CO2 capture technology development, availability and investment cost of the different technologies, with few operation cost analysis possible at the time. Main findings and the abatement potential for coal applications are presented. DOE, NETL, MIT, European universities and research institutions, key technology enterprises and utilities, and key technology suppliers are the main sources of this study. A vision of the technology deployment is presented.

The scenario of two-dimensional instabilities of the cylinder wake under EHD forcing: A linear stability analysis

We propose to study the stability properties of an air flow wake forced by a dielectric barrier discharge (DBD) actuator, which is a type of electrohydrodynamic (EHD) actuator. These actuators add momentum to the flow around a cylinder in regions close to the wall and, in our case, are symmetrically disposed near the boundary layer separation point. Since the forcing frequencies, typical of DBD, are much higher than the natural shedding frequency of the flow, we will be considering the forcing actuation as stationary. In the first part, the flow around a circular cylinder modified by EHD actuators will be experimentally studied by means of particle image velocimetry (PIV). In the second part, the EHD actuators have been numerically implemented as a boundary condition on the cylinder surface. Using this boundary condition, the computationally obtained base flow is then compared with the experimental one in order to relate the control parameters from both methodologies. After validating the obtained agreement, we study the Hopf bifurcation that appears once the flow starts the vortex shedding through experimental and computational approaches. For the base flow derived from experimentally obtained snapshots, we monitor the evolution of the velocity amplitude oscillations. As to the computationally obtained base flow, its stability is analyzed by solving a global eigenvalue problem obtained from the linearized Navier–Stokes equations. Finally, the critical parameters obtained from both approaches are compared.

Study of the Mechanical Strength Improvement of Wafers for EWT Solar Cells by Chemical Etching after the Drilling Process

Mechanical stability of EWT solar cells deteriorates when holes are created in the wafer. Nevertheless, the chemical etching after the hole generation process improves the mechanical strength by removing part of the damage produced in the drilling process. Several sets of wafers with alkaline baths of different duration have been prepared. The mechanical strength has been measured by the ring on ring bending test and the failure stresses have been obtained through a FE simulation of the test. This paper shows the comparison of these groups of wafers in order to obtain an optimum value of the decreased thickness produced by the chemical etching

Floating zone stability

The present state of de preparation of an experiment on floating liquid zones to be performed in the first Spacelab flight is presented. In this experiment,a liquid bridge is to be placed between two parallel coaxial disks (in the Fluid Physics Module)and subjected to very precise disturbances in order to check the theoretical predictions about its stability limits and behavior under mechanical inputs: stretching of the zone, filling or removing the liquid,axial vibration, rotation, disalignment, etc. Several aspects of the research are introduced:1) Relevance of the study. 2) Theoretical predictions of the liquid behavior regarding the floating-zone stability limits and the expected response to vibrational and rotational disturbances. 3) Ground support experiments using the Plateau technique or the small scale simulation. 4) Instrumental aspects of the experimentation: the Fluid Physics Module utilization and post-flight data analysis.5)Research program for future flights.

Comparative study of breakwater crown wall – calculation methods

An investigation was undertaken consisting of a state-of-the-art and comparative analysis of currently available methods for calculating the structural stability of wave walls in sloping breakwaters. A total of six design schemes are addressed. The conditions under which the formulations and ranges of validity are explicitly indicated by their authors, are given. The lack of definition in parameters to be used and aspects not taken into account in their investigations are discussed and the results of this analysis are given in a final table.

Study of the effect of different hole sizes on mechanical strength of wafers for back contact solar cells

Drilling process on wafers to produce EWT or MWT solar cells is a critical fabrication step, which affects on their mechanical stability. The amount of damage introduced during drilling process depends on the density of holes, their size and the chemical process applied afterwards. To quantify the relation between size of the holes and reduction of mechanical strength, several sets of wafers have been prepared, with different hole diameter. The mechanical strength of these sets has been measured by the ring on ring bending test, and the stress state in the moment of failure has been deduced by FE simulation.