Sistema de comunicaciones para una planta fotovoltaica

Las plantas solares fotovoltaicas, que son cada vez más habituales en nuestra sociedad, necesitan contar con un sistema de comunicaciones que permita la monitorización continua del funcionamiento de los diferentes equipos así como el control remoto de los mismos y la regulación de la producción. En este Proyecto se ha estudiado la estructura eléctrica y constructiva de una planta fotovoltaica genérica, prestando especial atención a los requerimientos que debe reunir el sistema de comunicaciones. El diseño del sistema de comunicaciones se ha realizado sobre una planta solar ficticia aún sin construir analizando su estructura sobre plano y aproximando la topología de red que se necesita implementar. Partiendo de esta estructura y de las cualidades de este tipo de instalaciones se ha realizado un análisis de las tecnologías disponibles, optando por una solución inalámbrica mixta, utilizando enlaces WiMAX y WiFi, manteniendo tecnología cableada únicamente para interconexión cercana de equipos. Esta elección se ha realizado con la intención de dotar a la planta de un sistema fiable, robusto y flexible sin descuidar el factor económico; para eso se ha cuidado la selección de equipamiento, su disposición en la planta y su configuración básica de funcionamiento. A partir de la solución definitiva se ha obtenido un presupuesto económico de la instalación. Se ha completado el diseño mediante simulaciones radioeléctricas, para asegurar un correcto funcionamiento de los diferentes enlaces. The photovoltaic solar power plants, which are becoming more common in our society, need a communications system that allowing continuous monitoring of the operation of the different devices as well as their remote control and regulation of the production. In this Project, electrical structure and construction of a generic photovoltaic solar plant have been studied, paying special attention to the essential requirements which must be fulfilled by the communication system. The communication system design is was carried out assuming that photovoltaic solar plant is fictitious and before its construction, analysing its structure over site plan and approximating the net topology in order to implement it. The analysis of the available technologies was performed basing on this structure as well as the qualities of this kind of facilities. As a result, a wireless mix option with WIMAX and WiFi links was chosen, using cable technology only to the close interconnection between equipments. This choice was made with the intention of giving the plant with a reliable, robust and flexible system without neglecting the economic factor, so that, the selection of equipment, the layout at the plant and operating basic configuration have been paid great attention. From the final solution is obtained a financial budget of the facility. Design is completed by radioelectric simulations to ensure the operation of the several links properly.

Diseño electrónico de la tarjeta de interfaz y control para un equipo de seguimiento en elevación en un subsistema de contramedidas electrónicas

Como apoyo al Subsistema ECM tradicional de los sistemas de Guerra Electrónica, surge el Equipo de Seguimiento en Elevación cuyo fin es la búsqueda de la amenaza en elevación. Ante la necesidad de un mayor número de líneas entre los bloques internos de este Equipo de Seguimiento, se hace necesario el diseño de una Tarjeta de Interfaz y Control. La tarjeta se ocupará de realizar el control de datos y flujo de señales de módulos RF que componen el Equipo, haciendo de interfaz entre las Tarjetas Procesadoras y Digitalizadoras, así como entre la Tarjeta de Proceso y el Bloque de Recepción. Una vez que se haya realizado el análisis de la necesidad de controlar estas señales, estudiado las especificaciones y los requisitos funcionales del Sistema, se procederá a implementar el diseño hardware y desarrollo firmware de la Tarjeta de Interfaz y Control de un Equipo de Seguimiento en Elevación para un Subsistema ECM, que constituye el objetivo de este PFC. ABSTRACT. In order to find a threat on elevation, and as a support on the basic ECM subsystems of E-war systems, the Elevation Tracking Equipment appears. To the need of a bigger number of lines between inside blocks of this Tracking Equipment, the design of an Interface and Control Board is needed. This board will deal with the data control and with the flow of RF modules signals that set up the Equipment, and will also work as an interface between the Processing and Digitalizing Board, as well as between the Process Board and the Reception Block. Once the signal control necessity analysis has been made, and once the specifications and functional System requirements have been studied, the hardware design and the firmware development will be ran as a target of PFC.

Sistema de control de tracción y salida para un monoplaza de la Fórmula SAE

En este proyecto de final de carrera se detalla el proceso de diseño, fabricación, montaje y ajuste de un dispositivo electrónico que sirva como sistema de control de tracción de un vehículo y que acoplaremos sobre un monoplaza de carreras que participa en la competición Formula SAE. La Formula SAE (Society of Automotive Engineers - Sociedad de Ingenieros de Automoción), es una competición de coches de carreras monoplaza a nivel universitario que promueve el desarrollo de la ingeniera aplicada a la automoción. Se pretende que este libro sirva de guía para el correcto manejo y desempeño del sistema fabricado. Además se ha pretendido que su lectura resulte fácil y comprensible para que la persona que lea este libro sea capaz de entender el sistema realizado para así poderlo mejorar. Gracias a la colaboración entre la Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación (ETSIST) de la Universidad Politécnica de Madrid (UPM), la Escuela de Ingenieros Industriales de esta misma Universidad (ETSII) y el Instituto Universitario de Investigación del Automóvil (INSIA), se sientan las bases de una plataforma docente en la cual se posibilita la formación y desarrollo de un vehículo tipo formula que participa en la ya mencionada competición Formula SAE. Para ello, se formo en el 2003 el equipo UPMRacing, primer representante español en el evento. El equipo se compone de más de 50 alumnos de la UPM y del Máster de Ingeniería en Automoción del INSIA. Es por tanto, en el vehículo fabricado por el equipo UPMRacing, en el que se pretende instalar este sistema de control de tracción. El control de tracción es un sistema de seguridad del automóvil diseñado para prevenir la perdida de adherencia cuando alguna rueda presenta deslizamiento, bien porque el conductor se excede en la aceleración o bien porque el firme este resbaladizo. La unidad de procesamiento del sistema de control de tracción fabricado lee la velocidad de cada rueda del vehículo mediante unos sensores y determina si existe deslizamiento, en tal caso, manda una señal a la centralita para disminuir la potencia hasta que el deslizamiento disminuya a unos valores controlados. El sistema cuenta con un control remoto que sirve como interfaz para que el piloto pueda manejarlo. Por ultimo, el dispositivo es capaz de conectarse a un bus de comunicaciones CAN para configurar ciertos parámetros. El objetivo del sistema es, básicamente, hacer que el coche no derrape en aceleraciones fuertes; concretamente en las salidas desde parado y al tomar una curva, aumentando así la velocidad en circuito y la seguridad del piloto. ABSTRACT. The purpose of this project is to describe the design, manufacture, assembly and adjustment processes of an electronic device acting as the traction control system (TCS) of a vehicle, that we will attach to a single-seater competition formula SAE car. The Formula SAE (Society of Automotive Engineers) is a graduate-level singleseater racing car competition promoting the development of automotive applied engineering. We also intend this work to serve as a technical user guide of the manufactured system. It is drafted clearly and concisely so that it will be easy for all those to whom it is addressed to understand and subject to further improvements. The close partnership among the Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación (ETSIST), Escuela de Ingenieros Industriales (ETSII) of Universidad Politécnica de Madrid (UPM), and the Instituto Universitario de Investigación del Automóvil (INSIA), lays the foundation of a teaching platform enabling the training and development of a single-seater racing car taking part in the already mentioned Formula SAE competition. In this respect, UPMRacing team was created back in 2003, first spanish representative in this event. The team consists of more than 50 students of the UPM and of INSIA Master in Automotive Engineering. It is precisely the vehicle manufactured by UPMRacing team where we intend to install our TCS. TCS is an automotive safety system designed to prevent loss of traction when one wheel has slip, either because the driver exceeds the acceleration or because the firm is slippery. The device’s central processing unit is able to detect the speed of each wheel of the vehicle via special sensors and to determine wheel slip. If this is the case, the system sends a signal to the ECU of the vehicle to reduce the power until the slip is also diminished to controlled values. The device has a remote control that serves as an interface for the pilot to handle it. Lastly, the device is able to connect to a communication bus system CAN to set up certain parameters. The system objective is to prevent skidding under strong acceleration conditions: standing-start from the starting grid or driving into a curve, increasing the speed in circuit and pilot’s safety.

Storage requirements for PV power ramp-rate control

Short-term variability in the power generated by large grid-connected photovoltaic (PV) plants can negatively affect power quality and the network reliability. New grid-codes require combining the PV generator with some form of energy storage technology in order to reduce short-term PV power fluctuation. This paper proposes an effective method in order to calculate, for any PV plant size and maximum allowable ramp-rate, the maximum power and the minimum energy storage requirements alike. The general validity of this method is corroborated with extensive simulation exercises performed with real 5-s one year data of 500 kW inverters at the 38.5 MW Amaraleja (Portugal) PV plant and two other PV plants located in Navarra (Spain), at a distance of more than 660 km from Amaraleja.

Loose Coupling Based Reference Scheme for Shop Floor-Control-System/Production-Equipment Integration.

Acoplamiento del sistema informático de control de piso de producción (SFS) con el conjunto de equipos de fabricación (SPE) es una tarea compleja. Tal acoplamiento involucra estándares abiertos y propietarios, tecnologías de información y comunicación, entre otras herramientas y técnicas. Debido a la turbulencia de mercados, ya sea soluciones personalizadas o soluciones basadas en estándares eventualmente requieren un esfuerzo considerable de adaptación. El concepto de acoplamiento débil ha sido identificado en la comunidad de diseño organizacional como soporte para la sobrevivencia de la organización. Su presencia reduce la resistencia de la organización a cambios en el ambiente. En este artículo los resultados obtenidos por la comunidad de diseño organizacional son identificados, traducidos y organizados para apoyar en la solución del problema de integración SFS-SPE. Un modelo clásico de acoplamiento débil, desarrollado por la comunidad de estudios de diseño organizacional, es resumido y trasladado al área de interés. Los aspectos claves son identificados para utilizarse como promotores del acoplamiento débil entre SFS-SPE, y presentados en forma de esquema de referencia. Así mismo, este esquema de referencia es presentado como base para el diseño e implementación de una solución genérica de acoplamiento o marco de trabajo (framework) de acoplamiento, a incluir como etapa de acoplamiento débil entre SFS y SPE. Un ejemplo de validación con varios conjuntos de equipos de fabricación, usando diferentes medios físicos de comunicación, comandos de controlador, lenguajes de programación de equipos y protocolos de comunicación es presentado, mostrando un nivel aceptable de autonomía del SFS. = Coupling shop floor software system (SFS) with the set of production equipment (SPE) becomes a complex task. It involves open and proprietary standards, information and communication technologies among other tools and techniques. Due to market turbulence, either custom solutions or standards based solutions eventually require a considerable effort of adaptation. Loose coupling concept has been identified in the organizational design community as a compensator for organization survival. Its presence reduces organization reaction to environment changes. In this paper the results obtained by the organizational de sign community are identified, translated and organized to support the SFS-SPE integration problem solution. A classical loose coupling model developed by organizational studies community is abstracted and translated to the area of interest. Key aspects are identified to be used as promoters of SFS-SPE loose coupling and presented in a form of a reference scheme. Furthermore, this reference scheme is proposed here as a basis for the design and implementation of a generic coupling solution or coupling framework, that is included as a loose coupling stage between SFS and SPE. A validation example with various sets of manufacturing equipment, using different physical communication media, controller commands, programming languages and wire protocols is presented, showing an acceptable level of autonomy gained by the SFS.

Educational Project for the Teaching of Control of Electric Traction Drives

Electric vehicles constitute a multidisciplinary subject that involves disciplines such as automotive, mechanical, electrical and control engineering. Due to this multidisciplinary technical nature, practical teaching methodologies are of special relevance. Paradoxically, in the past, the training of engineers specializing in this area has lacked the practical component represented by field tests, due to the difficulty of accessing real systems. This paper presents an educational project specifically designed for the teaching and training of engineering students with different backgrounds and experience. The teaching methodology focuses on the topology of electric traction drives and their control. It includes two stages, a simulation computer model and a scaled laboratory workbench that comprises a traction electrical drive coupled to a vehicle emulator. With this equipment, the effectiveness of different traction control strategies can be analyzed from the point of view of energy efficiency, robustness, easiness of implementation and acoustic noise.

Proprioceptive force estimation and control for teleoperation in radioactive environments

A medida que se incrementa la energía de los aceleradores de partículas o iones pesados como el CERN o GSI, de los reactores de fusión como JET o ITER, u otros experimentos científicos, se va haciendo cada vez más imprescindible el uso de técnicas de manipulación remota para la interacción con el entorno sujeto a la radiación. Hasta ahora la tasa de dosis radioactiva en el CERN podía tomar valores cercanos a algunos mSv para tiempos de enfriamiento de horas, que permitían la intervención humana para tareas de mantenimiento. Durante los primeros ensayos con plasma en JET, se alcanzaban valores cercanos a los 200 μSv después de un tiempo de enfriamiento de 4 meses y ya se hacía extensivo el uso de técnicas de manipulación remota. Hay una clara tendencia al incremento de los niveles de radioactividad en el futuro en este tipo de instalaciones. Un claro ejemplo es ITER, donde se esperan valores de 450 Sv/h en el centro del toroide a los 11 días de enfriamiento o los nuevos niveles energéticos del CERN que harán necesario una apuesta por niveles de mantenimiento remotos. En estas circunstancias se enmarca esta tesis, que estudia un sistema de control bilateral basado en fuerza-posición, tratando de evitar el uso de sensores de fuerza/par, cuyo contenido electrónico los hace especialmente sensitivos en estos ambientes. El contenido de este trabajo se centra en la teleoperación de robots industriales, que debido a su reconocida solvencia y facilidad para ser adaptados a estos entornos, unido al bajo coste y alta disponibilidad, les convierte en una alternativa interesante para tareas de manipulación remota frente a costosas soluciones a medida. En primer lugar se considera el problema cinemático de teleoperación maestro-esclavo de cinemática disimilar y se desarrolla un método general para la solución del problema en el que se incluye el uso de fuerzas asistivas para guiar al operador. A continuación se explican con detalle los experimentos realizados con un robot ABB y que muestran las dificultades encontradas y recomendaciones para solventarlas. Se concluye el estudio cinemático con un método para el encaje de espacios de trabajo entre maestro y esclavo disimilares. Posteriormente se mira hacia la dinámica, estudiándose el modelado de robots con vistas a obtener un método que permita estimar las fuerzas externas que actúan sobre los mismos. Durante la caracterización del modelo dinámico, se realizan varios ensayos para tratar de encontrar un compromiso entre complejidad de cálculo y error de estimación. También se dan las claves para modelar y caracterizar robots con estructura en forma de paralelogramo y se presenta la arquitectura de control deseada. Una vez obtenido el modelo completo del esclavo, se investigan diferentes alternativas que permitan una estimación de fuerzas externas en tiempo real, minimizando las derivadas de la posición para minimizar el ruido. Se comienza utilizando observadores clásicos del estado para ir evolucionando hasta llegar al desarrollo de un observador de tipo Luenberger-Sliding cuya implementación es relativamente sencilla y sus resultados contundentes. También se analiza el uso del observador propuesto durante un control bilateral simulado en el que se compara la realimentación de fuerzas obtenida con las técnicas clásicas basadas en error de posición frente a un control basado en fuerza-posición donde la fuerza es estimada y no medida. Se comprueba como la solución propuesta da resultados comparables con las arquitecturas clásicas y sin embargo introduce una alternativa para la teleoperación de robots industriales cuya teleoperación en entornos radioactivos sería imposible de otra manera. Finalmente se analizan los problemas derivados de la aplicación práctica de la teleoperación en los escenarios mencionados anteriormente. Debido a las condiciones prohibitivas para todo equipo electrónico, los sistemas de control se deben colocar a gran distancia de los manipuladores, dando lugar a longitudes de cable de centenares de metros. En estas condiciones se crean sobretensiones en controladores basados en PWM que pueden ser destructivas para el sistema formado por control, cableado y actuador, y por tanto, han de ser eliminadas. En este trabajo se propone una solución basada en un filtro LC comercial y se prueba de forma extensiva que su inclusión no produce efectos negativos sobre el control del actuador. ABSTRACT As the energy on the particle accelerators or heavy ion accelerators such as CERN or GSI, fusion reactors such as JET or ITER, or other scientific experiments is increased, it is becoming increasingly necessary to use remote handling techniques to interact with the remote and radioactive environment. So far, the dose rate at CERN could present values near several mSv for cooling times on the range of hours, which allowed human intervention for maintenance tasks. At JET, they measured values close to 200 μSv after a cooling time of 4 months and since then, the remote handling techniques became usual. There is a clear tendency to increase the radiation levels in the future. A clear example is ITER, where values of 450 Sv/h are expected in the centre of the torus after 11 days of cooling. Also, the new energetic levels of CERN are expected to lead to a more advanced remote handling means. In these circumstances this thesis is framed, studying a bilateral control system based on force-position, trying to avoid the use of force/torque sensors, whose electronic content makes them very sensitive in these environments. The contents of this work are focused on teleoperating industrial robots, which due its well-known reliability, easiness to be adapted to these environments, cost-effectiveness and high availability, are considered as an interesting alternative to expensive custom-made solutions for remote handling tasks. Firstly, the kinematic problem of teloperating master and slave with dissimilar kinematics is analysed and a new general approach for solving this issue is presented. The solution includes using assistive forces in order to guide the human operator. Coming up next, I explain with detail the experiments accomplished with an ABB robot that show the difficulties encountered and the proposed solutions. This section is concluded with a method to match the master’s and slave’s workspaces when they present dissimilar kinematics. Later on, the research studies the dynamics, with special focus on robot modelling with the purpose of obtaining a method that allows to estimate external forces acting on them. During the characterisation of the model’s parameters, a set of tests are performed in order to get to a compromise between computational complexity and estimation error. Key points for modelling and characterising robots with a parallelogram structure are also given, and the desired control architecture is presented. Once a complete model of the slave is obtained, different alternatives for external force estimation are review to be able to predict forces in real time, minimizing the position differentiation to minimize the estimation noise. The research starts by implementing classic state observers and then it evolves towards the use of Luenberger- Sliding observers whose implementation is relatively easy and the results are convincing. I also analyse the use of proposed observer during a simulated bilateral control on which the force feedback obtained with the classic techniques based on the position error is compared versus a control architecture based on force-position, where the force is estimated instead of measured. I t is checked how the proposed solution gives results comparable with the classical techniques and however introduces an alternative method for teleoperating industrial robots whose teleoperation in radioactive environments would have been impossible in a different way. Finally, the problems originated by the practical application of teleoperation in the before mentioned scenarios are analysed. Due the prohibitive conditions for every electronic equipment, the control systems should be placed far from the manipulators. This provokes that the power cables that fed the slaves devices can present lengths of hundreds of meters. In these circumstances, overvoltage waves are developed when implementing drives based on PWM technique. The occurrence of overvoltage is very dangerous for the system composed by drive, wiring and actuator, and has to be eliminated. During this work, a solution based on commercial LC filters is proposed and it is extensively proved that its inclusion does not introduce adverse effects into the actuator’s control.

Soporte de redes activas para un servicio integrado de multipunto fiable con control de congestión

Las limitaciones de las tecnologías de red actuales, identificadas en la Agencia de Proyectos de Investigación Avanzados para la Defensa (DARPA) durante 1995, han originado recientemente una propuesta de modelo de red denominado Redes Activas. En este modelo, los nodos proporcionan un entorno de ejecución sobre el que se ejecuta el código asociado a cada paquete. El objetivo es disponer de una tecnología de red que permita que nuevos servicios de red sean desarrollados e instalados rápidamente sin modificar los nodos de la red. Un servicio de red que se puede beneficiar de esta tecnología es la transmisión de datos en multipunto con diferentes grados fiabilidad. Las propuestas actuales de servicios de multipunto fiable proporcionan una solución específica para cada clase de aplicaciones, y los protocolos existentes extremo a extremo sufren de limitaciones técnicas relacionadas con una fiabilidad limitada, y con la ausencia de mecanismos de control de congestión efectivos. Esta tesis realiza propuestas originales conducentes a solucionar parte de las limitaciones actuales en el ámbito de Redes Activas y multipunto fiable con control de congestión. En primer lugar, se especificará un servicio genérico de multipunto fiable que, basándose en los requisitos de una serie de aplicaciones consideradas relevantes, proporcione diferentes clases de sesiones y grados de fiabilidad. Partiendo de la definición del servicio genérico especificado, se diseñará un protocolo de comunicaciones sobre la tecnología de Redes Activas que proporcione dicho servicio. El protocolo diseñado estará dotado de un mecanismo de control de congestión para que la fuente ajuste dinámicamente el tráfico inyectado a las condiciones de carga de la red. En esta tesis se pretende también profundizar en el estudio y análisis de la tecnología de Redes Activas, experimentando con dicha tecnología para proporcionar una realimentación a sus diseñadores. Dicha experimentación se realizará en tres ámbitos: el de los servicios y protocolos que puede soportar, el del modelo y arquitectura de las Redes Activas y el de las plataformas de ejecución disponibles. Como aportación adicional de este trabajo, se validarán los objetivos anteriores mediante una implementación piloto de las entidades de protocolo y de su interfaz de servicio sobre uno de los entornos de ejecución disponibles. Abstract The limitations of current networking technologies identified in the Defense Advance Research Projects Agency (DARPA) along 1995 have led to a recent proposal of a new network model called Active Networks. In this model, the nodes provide an execution environment over which the code used to process each packet is executed. The objective is a network technology that allows the fast design and deployment of new network services without requiring the modification of the network nodes. One network service that could benefit from this technology is the transmission of multicast data with different types of loss tolerance. The current proposals for reliable multicast services provide specific solutions for each application class, and existing end-to-end protocols suffer from technical drawbacks related to limited reliability and lack of an effective congestion control mechanism. This thesis contains original proposals that aim to solve part of the current drawbacks in the scope of Active Networks and reliable multicast with congestion control. Firstly, a generic reliable multicast network service will be specified. This service will be designed from the requirements of a relevant set of applications, and will provide different session classes and different types of reliability. Then, a network protocol based on Active Network technology will be designed such that it provides the specified network service. This protocol will incorporate a congestion control mechanism capable of performing an automatic adjustment of the traffic injected by the source to the available network capacity. This thesis will also contribute to a deeper study and analysis of Active Network technology, by experimenting with the technology in order to provide feedback to its designers. This experimentation will be done attending to three different scopes: support of Active Network for services and protocols, Active Network model and architecture, and currently available Active Network execution environments. As an additional contribution of this work, the previous objectives will be validated through a prototype implementation of the protocol entities and the service interface based on one of the current execution environments.

A speech interface for air traffic control terminals

Several issues concerning the current use of speech interfaces are discussed and the design and development of a speech interface that enables air traffic controllers to command and control their terminals by voice is presented. A special emphasis is made in the comparison between laboratory experiments and field experiments in which a set of ergonomics-related effects are detected that cannot be observed in the controlled laboratory experiments. The paper presents both objective and subjective performance obtained in field evaluation of the system with student controllers at an air traffic control (ATC) training facility. The system exhibits high word recognition test rates (0.4% error in Spanish and 1.5% in English) and low command error (6% error in Spanish and 10.6% error in English in the field tests). Subjective impression has also been positive, encouraging future development and integration phases in the Spanish ATC terminals designed by Aeropuertos Españoles y Navegación Aérea (AENA).

Estrategias para el control microclimático del espacio entre edificaciones en clima cálido – húmedo

La presente investigación parte del problema en las zonas de clima cálido - húmedo en las cuales se producen impactos asociados a la incomodidad térmica producto de la intensa radiación solar, altas temperaturas y elevada humedad. Estos factores reducen la calidad de los espacios abiertos y desarrollan en la población una actitud de rechazo hacia el uso del microespacio urbano entre edificaciones en los desarrollos urbanos - conjuntos urbanos - , los mismos frecuentemente admiten soluciones que al parecer no contribuyen a la realización de las actividades comunes de esparcimiento de la población residente. Por lo tanto, el objetivo de la investigación es profundizar en la temática urbano - ambiental - social y el diseño urbano vinculada a la particularidad morfológica local, las condiciones microclimáticas, el uso del microespacio y los requerimientos de los usuarios. La finalidad de desarrollar estrategias de control microclimático del microespacio entre edificios en clima cálido - húmedo en búsqueda de soluciones óptimas que satisfagan las necesidades de los usuarios de los espacios exteriores en estas áreas residenciales. La investigación se centra en el estudio de las particularidades contextuales relacionadas con el microclima y las características urbanas - morfotipológicas, básicamente los factores microclimáticos (soleamiento y ventilación), los morfológicos y edificatorios y las características de las superficies (pavimentos). En coherencia con el objetivo propuesto el trabajo se desarrolla en cuatro fases: la primera aborda la revisión documental, literatura relevante e investigaciones relativas a la calidad ambiental, medio social, medio físico, el microespacio urbano, control y diseño sostenible, modelización proyectual y estrategias sostenibles; la segunda fase se refiere al marco contextual, características urbanas, datos climáticos locales, planes y procesos urbanos, tipologías y conformación urbana. En esta fase se describe el proceso de selección, análisis y evaluación urbano - ambiental de los casos de estudio (conjuntos residenciales). En la tercera fase se aborda el marco evaluativo y estudio de casos, consideraciones físicas, climáticas y valoración térmico - ambiental de los conjuntos residenciales seleccionados. En esta fase se aplican Técnicas Estadísticas y de Simulación Computacional y se analizan los resultados obtenidos. Finalmente, la cuarta fase propositiva incluye el establecimiento de Estrategias, Principios y Lineamientos de optimación térmica y se exponen las Conclusiones parciales de la tesis, alcances y perspectivas futuras. Finalmente, los resultados obtenidos en la investigación demuestran que el análisis en las experiencias de la realidad permiten comprobar que las situaciones y alteraciones ambientales sustanciales, los niveles de afectación térmica y las condiciones de confortabilidad e impacto derivan de las características urbanas, los componentes del microespacio y de las condiciones climáticas las cuales afectan el desarrollo de las actividades y el uso efectivo del microespacio entre edificios. El análisis de los factores morfo - climáticos incidentes y el estudio de los efectos de interacción contribuyen al establecimiento de Principios y Lineamientos para la evaluación y diseño sostenible del microespacio entre edificios y el uso correcto de los elementos del clima en estas áreas urbanas destinadas a la actividad social y al esparcimiento de la población residente. ABSTRACT This research starts from the problem of hot - humid climate zones where impacts related to thermal discomfort are produced as a result from the intense solar radiation and high temperatures and humidity. These factors reduce the quality of open spaces and people develop an attitude of rejection towards the use of urban microspace among buildings within urban developments - urban complexes - . Usually, these complexes admit solutions that apparently do not contribute to the achievement of common leisure activities in the resident dwellers. Therefore, the main purpose of this research is to deepen in the urban - environmental - social issue and urban design linked to the local morphological particularity, microclimate conditions, use of microspace and users’ requirements. In order to develop microclimate control strategies of microspace among buildings in hot - humid climate to look for optimal solutions that satisfy users’ needs of outdoors spaces in these residential areas. The research focuses in the study of contextual particularities related to microclimate and urban - morphotypological characteristics. Basically, microclimate (sunlight and ventilation), morphological and building factors as well as road surface characteristics. According to the proposed objective, this research is developed in four phases: the first one considers documentary review, relevant literature and researches related to environmental quality, social environment, physical environment, urban microspace, control and sustainable design, project modelling and sustainable strategies; while the second phase refers to contextual framework, urban characteristics, local climate data, plans and urban processes, typologies and urban structure. In this phase, the process of selection, analysis and urban - environmental evaluation of case studies (residential complexes) is described. The third phase approaches the assessment framework and case studies, physical and climate considerations as well as environmental - thermal evaluation of selected residential complexes. In this phase, statistical techniques and computational simulations are applied. Likewise, results obtained are analysed. Similarly, fourth and proposing phase includes the establishment of strategies, principles and guidelines of thermal optimization and partial conclusions of the thesis, scopes and future perspectives are exposed. Finally, from the results obtained, it is demonstrated that the analysis on reality experiences allow proving that situations and substantial environmental changes, levels of thermal affectations, comfort conditions and impact derive from urban characteristics, microspace components and from climate conditions which affect the development of activities and the effective use of microspace among buildings. The analysis of incidental morpho - climate factors and the study of interaction effects contribute to the establishment of principles and guidelines for the assessment and sustainable design of microspace among buildings as well as the correct use of climate elements in these urban areas oriented to social and leisure activities of resident population.

Formal verification of safety protocol in train control system

In order to satisfy the safety-critical requirements, the train control system (TCS) often employs a layered safety communication protocol to provide reliable services. However, both description and verification of the safety protocols may be formidable due to the system complexity. In this paper, interface automata (IA) are used to describe the safety service interface behaviors of safety communication protocol. A formal verification method is proposed to describe the safety communication protocols using IA and translate IA model into PROMELA model so that the protocols can be verified by the model checker SPIN. A case study of using this method to describe and verify a safety communication protocol is included. The verification results illustrate that the proposed method is effective to describe the safety protocols and verify deadlocks, livelocks and several mandatory consistency properties. A prototype of safety protocols is also developed based on the presented formally verifying method.

Robustness Analysis of Eigenstructure Assignment Controllers on Rigid-Flexible Satellites

Flexible spacecraft with attached solar panels may exhibit undesired vibrations and structural deformations. These types of vehicles show an intrinsic coupling of the elements of the structure. The attitude maneuvers performed by flexible spacecraft may cause non-desired deflections of attached flexible elements. Any attitude and orbit control system generally solves these problems using filters that are designed to attenuate the relative deflections of flexible appendages. In this paper, we propose a method for designing attitude static controllers using an eigenstructure assignment (EA) method. A set of requirements were specified from our understanding of the system modes in an open loop. Exhaustive theoretical and numerical simulations were performed on special cases to verify the controller design procedure. In the design of the controller, we considered all of the aspects that relate to the eigenstructure assignment. The primary objective of this paper is to demonstrate the feasibility of obtaining a high degree of decoupling for some selected modes via the application of an EA method. Finally a robustness analysis is perform to the system together with the designed controller by means of a mu-analysis

Current Mode with RMS Voltage and Offset Control Loops for a Single-Phase Aircraft Inverter Suitable for Parallel and 3-Phase Operation Modes

Rms voltage regulation may be an attractive possibility for controlling power inverters. Combined with a Hall Effect sensor for current control, it keeps its parallel operation capability while increasing its noise immunity, which may lead to a reduction of the Total Harmonic Distortion (THD). Besides, as voltage regulation is designed in DC, a simple PI regulator can provide accurate voltage tracking. Nevertheless, this approach does not lack drawbacks. Its narrow voltage bandwidth makes transients last longer and it increases the voltage THD when feeding non-linear loads, such as rectifying stages. On the other hand, the implementation can fall into offset voltage error. Furthermore, the information of the output voltage phase is hidden for the control as well, making the synchronization of a 3-phase setup not trivial. This paper explains the concept, design and implementation of the whole control scheme, in an on board inverter able to run in parallel and within a 3-phase setup. Special attention is paid to solve the problems foreseen at implementation level: a third analog loop accounts for the offset level is added and a digital algorithm guarantees 3-phase voltage synchronization.

Secure access control by means of human stress detection

This paper proposes a stress detection system based on fuzzy logic and the physiological signals heart rate and galvanic skin response. The main contribution of this method relies on the creation of a stress template, collecting the behaviour of previous signals under situations with a different level of stress in each individual. The creation of this template provides an accuracy of 99.5% in stress detection, improving the results obtained by current pattern recognition techniques like GMM, k-NN, SVM or Fisher Linear Discriminant. In addition, this system can be embedded in security systems to detect critical situations in accesses as cross-border control. Furthermore, its applications can be extended to other fields as vehicle driver state-of-mind management, medicine or sport training.

Research lines in Hyperthermia at the Bioinstrumentation Laboratory of the Centre for Biomedical Technology

The Bioinstrumentation Laboratory belongs to the Centre for Biomedical Technology (CTB) of the Technical University of Madrid and its main objective is to provide the scientific community with devices and techniques for the characterization of micro and nanostructures and consequently finding their best biomedical applications. Hyperthermia (greek word for “overheating”) is defined as the phenomenon that occurs when a body is exposed to an energy generating source that can produce a rise in temperature (42-45ºC) for a given time [1]. Specifically, the aim of the hyperthermia methods used in The Bioinstrumentation Laboratory is the development of thermal therapies, some of these using different kinds of nanoparticles, to kill cancer cells and reduce the damage on healthy tissues. The optical hyperthermia is based on noble metal nanoparticles and laser irradiation. This kind of nanoparticles has an immense potential associated to the development of therapies for cancer on account of their Surface Plasmon Resonance (SPR) enhanced light scattering and absorption. In a short period of time, the absorbed light is converted into localized heat, so we can take advantage of these characteristics to heat up tumor cells in order to obtain the cellular death [2]. In this case, the laboratory has an optical hyperthermia device based on a continuous wave laser used to kill glioblastoma cell lines (1321N1) in the presence of gold nanorods (Figure 1a). The wavelength of the laser light is 808 nm because the penetration of the light in the tissue is deeper in the Near Infrared Region. The first optical hyperthermia results show that the laser irradiation produces cellular death in the experimental samples of glioblastoma cell lines using gold nanorods but is not able to decrease the cellular viability of cancer cells in samples without the suitable nanorods (Figure 1b) [3]. The generation of magnetic hyperthermia is performed through changes of the magnetic induction in magnetic nanoparticles (MNPs) that are embedded in viscous medium. The Figure 2 shows a schematic design of the AC induction hyperthermia device in magnetic fluids. The equipment has been manufactured at The Bioinstrumentation Laboratory. The first block implies two steps: the signal selection with frequency manipulation option from 9 KHz to 2MHz, and a linear output up to 1500W. The second block is where magnetic field is generated ( 5mm, 10 turns). Finally, the third block is a software control where the user can establish initial parameters, and also shows the temperature response of MNPs due to the magnetic field applied [4-8]. The Bioinstrumentation Laboratory in collaboration with the Mexican company MRI-DT have recently implemented a new research line on Nuclear Magnetic Resonance Hyperthermia, which is sustained on the patent US 7,423,429B2 owned by this company. This investigation is based on the use of clinical MRI equipment not only for diagnosis but for therapy [9]. This idea consists of two main facts: Magnetic Resonance Imaging can cause focal heating [10], and the differentiation in resonant frequency between healthy and cancer cells [11]. To produce only heating in cancer cells when the whole body is irradiated, it is necessary to determine the specific resonant frequency of the target, using the information contained in the spectra of the area of interest. Then, special RF pulse sequence is applied to produce fast excitation and relaxation mechanism that generates temperature increase of the tumor, causing cellular death or metabolism malfunction that stops cellular division