Power system stability of a small sized isolated network supplied by a combined wind-pumped storage generation system: a case study in the Canary Islands

Massive integration of renewable energy sources in electrical power systems of remote islands is a subject of current interest. The increasing cost of fossil fuels, transport costs to isolated sites and environmental concerns constitute a serious drawback to the use of conventional fossil fuel plants. In a weak electrical grid, as it is typical on an island, if a large amount of conventional generation is substituted by renewable energy sources, power system safety and stability can be compromised, in the case of large grid disturbances. In this work, a model for transient stability analysis of an isolated electrical grid exclusively fed from a combination of renewable energy sources has been studied. This new generation model will be installed in El Hierro Island, in Spain. Additionally, an operation strategy to coordinate the generation units (wind, hydro) is also established. Attention is given to the assessment of inertial energy and reactive current to guarantee power system stability against large disturbances. The effectiveness of the proposed strategy is shown by means of simulation results.

An Intelligent Assistant for Public Transport Management

This paper describes the architecture of a computer system conceived as an intelligent assistant for public transport management. The goal of the system is to help operators of a control center in making strategic decisions about how to solve problems of a fleet of buses in an urban network. The system uses artificial intelligence techniques to simulate the decision processes. In particular, a complex knowledge model has been designed by using advanced knowledge engineering methods that integrates three main tasks: diagnosis, prediction and planning. Finally, the paper describes two particular applications developed following this architecture for the cities of Torino (Italy) and Vitoria (Spain).

Estudio de rehabilitación acústica de los edificios del barrio de Lavapiés

Los tejidos urbanos, los barrios y los edificios en proceso de degradación física, social o ambiental requieren acciones de rehabilitación urbana que garanticen el bienestar de las personas. La sociedad demanda, cada vez más, el derecho al descanso y a una vida sin ruidos, como signo de desarrollo y progreso. Es por ello, que se debe conducir el comportamiento de la edificación y del metabolismo urbano hacia unos mínimos de calidad acústica que permitan mejorar las deficiencias de aislamiento acústico que presentan los edificios existentes de gran parte de las ciudades y sus centros históricos. En este sentido, el objetivo de este Trabajo de Fin de Máster es el de contribuir al estudio de las acciones de rehabilitación y las soluciones técnicas que permitan desarrollar edificios acústicamente eficientes en el barrio de Lavapiés. Como punto de partida se realizará la caracterización urbanística del barrio, analizando la calidad de la edificación, la geometría de las calles, los principales viarios, para posteriormente estudiar la cartografía acústica de Lavapiés a través de los Mapas Estratégicos de Ruido. Porque el ruido tiene una importante componente subjetiva, se realizará además una encuesta de calidad acústica para conocer la opinión del ciudadano de Lavapiés, tratando de comprender la problemática de ruido en el barrio y cómo afecta ésta a sus vecinos. Por último se desarrollarán unas directrices generales para la rehabilitación acústica de los edificios existentes, y se llevarán a la práctica realizando una propuesta de rehabilitación acústica de un edificio del siglo XIX situado en la Calle Ave María de Lavapiés. Cada obra de rehabilitación es una oportunidad de mejorar las deficientes condiciones acústicas de los edificios dentro de lo viable técnica y económicamente, a pesar de que puede que no se lleguen a alcanzar los niveles exigidos en el DB HR. SUMMARY. The urban network, the neighborhoods and the buildings in progress of physical, social and environmental degradation require actions of urban restoration to guarantee people’s welfare. Society demands, more every time, the right to rest and to life without noise, as an evidence of development and progress. That is why, the behavior of building and the urban metabolism must be lead to the best acoustic quality allowing to improve the acoustic sound proofing deficiencies that now a days some of the existing buildings present in most of the cities and its historical downtowns. In this direction, the goal of this “Trabajo de Fin de Master” is to contribute to the study of the rehabilitation actions and the technical solutions that will make possible to develop acoustically efficient buildings in Lavapies area. To begin a urbanistic classification of the neighborhood will be done, analyzing the quality of construction, the geometry of the streets, the main road routes to study, afterwards,the acoustic cartography of Lavapies through the Strategic Maps of Noise. Also because noise has an important subjective component, a survey about acoustic quality will be made to know the opinion of Lavapies citizens, trying to understand the problems of noise in the neighborhood and how this may affect its neighbors. Finally some general guidelines of the acoustic rehabilitation of the buildings will be shown and materialized in a proposal of an acoustic rehabilitation of a XIX century building placed in Ave María Street in Lavapies. Each rehabilitation work is a chance to improve the insufficient acoustic conditions of the buildings within technical and economical possibilities, despite of the fact that it might not be possible to reach the levels demand by the DB HR anyway.

Bioaccessibility of heavy metals and risk assessment in urban gardens of Madrid

Human health problems and solutions. Urban gardening has spread worldwide in recent years as it enhances food security and selfsupply and promotes community integration. However urban soils are significantly enriched in trace elements relative to background levels. Exposure to the soil in urban gardens may therefore result in adverse health effects depending on the degree of contact during gardening, infant recreational activities and ingestion of vegetables grown in them. In order to evaluate this potential risk, 36 composite samples were collected from the top 20 cm of the soil of 6 urban gardens in Madrid. The aqua regia (pseudototal) and glycine-extractable (bioaccessible) concentrations of Co, Cr, Cu, Ni, Pb and Zn were determined by atomic absorption spectrophotometry. Additionally, pH, texture, Fe, Ca, and Mn concentrations, and organic matter and calcium carbonate contents were determined in all urban gardens and their influence on trace element bioaccessibility was analyzed.

El vacío entre infraestructuras lineales y ciudad: espacios anómalos como oportunidad para lo colectivo

Partiendo del estudio del vacío del muro de Berlín en el Laboratorio de Paisaje como infraestructura lineal y espacio anómalo, se pretende profundizar la investigación de los vacíos generados por las infraestructuras lineales que atraviesan nuestras ciudades, espacios marginales, olvidados o apartados de la trama urbana pero llenos de identidad y significado donde se pueden generar nuevas oportunidades para el espacio público. A través de un estudio de casos se intentará analizar la potencialidad de este tipo de espacios intermedios como nuevos espacios para la colectividad a través de su re-significación y de su conexión con la red de espacios publicos urbanos. ABSTRACT. Based on the study of the void within the Berlin Wall at the Lab in the first semester as linear infrastructure and anomalous space, this research aims to study the gaps generated by linear infrastructures that pass through our cities, marginal spaces, forgotten or disconnected from the urban network but full of identity and meaning where new opportunities can be created for the public space. Through a case study will analyze the potential of such gaps as new spaces for the community through its re-signification and its connection with the network of urban public spaces.

Metodología para el análisis de los efectos de la rotura de un depósito en entorno urbano y clasificación de su riesgo potencial

El riesgo asociado a la rotura de un depósito de agua en entorno urbano (como la ocurrida, por ejemplo, en la Ciudad Autónoma de Melilla en Noviembre de 1997) y los potenciales daños que puede causar, pone en duda la seguridad de este tipo de infraestructuras que, por necesidades del servicio de abastecimiento de agua, se construyen habitualmente en puntos altos y cercanos a los núcleos de población a los que sirven. Sin embargo, la baja probabilidad de que se produzca una rotura suele rebajar los niveles de alerta asociados a los depósitos, haciéndose hincapié en la mejora de los métodos constructivos sin elaborar metodologías que, como en el caso de las presas y las balsas de riego, establezcan la necesidad de clasificar el riesgo potencial de estas infraestructuras en función de su emplazamiento y de estudiar la posible construcción de medidas mitigadoras de una posible rotura. Por otro lado, para establecer los daños que pueden derivarse de una rotura de este tipo, se hace imprescindible la modelización bidimensional de la ola de rotura por cuanto la malla urbana a la que afectaran no es susceptible de simulaciones unidimensionales, dado que no hay un cauce que ofrezca un camino preferente al agua. Este tipo de simulación requiere de una inversión económica que no siempre está disponible en la construcción de depósitos de pequeño y mediano tamaño. Esta tesis doctoral tiene como objetivo el diseño de una metodología simplificada que, por medio de graficas y atendiendo a las variables principales del fenómeno, pueda estimar un valor para el riesgo asociado a una posible rotura y sirva como guía para establecer si un deposito (existente o de nueva implantación) requiere de un modelo de detalle para estimar el riesgo y si es conveniente implantar alguna medida mitigadora de la energía producida en una rotura de este tipo. Con carácter previo se ha establecido que las variables que intervienen en la definición de riesgo asociado a la rotura, son el calado y la velocidad máxima en cada punto sensible de sufrir daños (daños asociados al vuelco y arrastre de personas principalmente), por lo que se ha procedido a estudiar las ecuaciones que rigen el problema de la rotura del depósito y de la transmisión de la onda de rotura por la malla urbana adyacente al mismo, así como los posibles métodos de resolución de las mismas y el desarrollo informático necesario para una primera aproximación a los resultados. Para poder analizar las condiciones de contorno que influyen en los valores resultantes de velocidad y calado, se ha diseñado una batería de escenarios simplificados que, tras una modelización en detalle y un análisis adimensional, han dado como resultado que las variables que influyen en los valores de calado y velocidad máximos en cada punto son: la altura de la lamina de agua del depósito, la pendiente del terreno, la rugosidad, la forma del terreno (en términos de concavidad) y la distancia del punto de estudio al deposito. Una vez definidas las variables que influyen en los resultados, se ha llevado a cabo una segunda batería de simulaciones de escenarios simplificados que ha servido para la discusión y desarrollo de las curvas que se presentan como producto principal de la metodología simplificada. Con esta metodología, que solamente necesita de unos cálculos simples para su empleo, se obtiene un primer valor de calado y velocidad introduciendo la altura de la lámina de agua máxima de servicio del depósito cuyo riesgo se quiere evaluar. Posteriormente, y utilizando el ábaco propuesto, se obtienen coeficientes correctores de los valores obtenidos para la rugosidad y pendiente media del terreno que se esta evaluando, así como para el grado de concavidad del mismo (a través de la pendiente transversal). Con los valores obtenidos con las curvas anteriores se obtienen los valores de calado y velocidad en el punto de estudio y, aplicando la formulación propuesta, se obtiene una estimación del riesgo asociado a la rotura de la infraestructura. Como corolario a la metodología mencionada, se propone una segunda serie de gráficos para evaluar, también de forma simplificada, la reducción del riesgo que se obtendría con la construcción de alguna medida mitigadora como puede ser un dique o murete perimetral al depósito. Este método de evaluación de posible medidas mitigadoras, aporta una guía para analizar la posibilidad de disminuir el riesgo con la construcción de estos elementos, o la necesidad de buscar otro emplazamiento que, si bien pueda ser no tan favorable desde el punto de vista de la explotación del depósito, presente un menor riesgo asociado a su rotura. Como complemento a la metodología simplificada propuesta, y además de llevar a cabo la calibración de la misma con los datos obtenidos tras la rotura del depósito de agua de Melilla, se ha realizado una serie de ejemplos de utilización de la metodología para, además de servir de guía de uso de la misma, poder analizar la diferencia entre los resultados que se obtendrían con una simulación bidimensional detallada de cada uno de los casos y el método simplificado aplicado a los mismos. The potential risk of a catastrophic collapse of a water supply reservoir in an urban area (such as the one occurred in Melilla in November 1997) and the damages that can cause, make question the security in this kind of infrastructures, which, by operational needs, are frequently built in high elevations and close to the urban areas they serve to. Since the likelihood of breakage is quite low, the alert levels associated to those infrastructures have also been downgraded focussing on the improvement of the constructive methods without developing methodologies (like the ones used in the case of dams or irrigation ponds) where there is a need of classifying the potential risk of those tanks and also of installing mitigating measures. Furthermore, to establish the damages related to a breakage of this kind, a twodimensional modelling of the breakage wave becomes imperative given that the urban layout does not provide a preferential way to the water. This kind of simulation requires financial investment that is not always available in the construction of small and medium sized water tanks. The purpose of this doctoral thesis is to design a simplified methodology, by means of charts and attending to the main variables of the phenomenon, that could estimate a value to the risk associated to a possible breakage. It can also be used as a guidance to establish if a reservoir (existing or a new one) requires a detailed model to estimate the risk of a breakage and the benefits of installing measures to mitigate the breakage wave effects. Previously, it has been established that the variables involved in the risk associated to a breakage are the draft and the maximum speed in every point susceptible to damages (mainly damages related to people). Bellow, the equations ruling the problem of the reservoir breakage have been studied as well as the transmission of the breakage wave through the urban network of the city and the possible methods to solve the equations and the computer development needed to a first approach to the results. In order to be able to analyse the boundary conditions affecting the values resulting (speed and draft), a set of scenarios have been designed. After a detailed modelling and a dimensionless analysis it has been proved that the variables that influence the operational draughts and the maximum speed in every point are the water level in the tank, the slope, the roughness and form (in terms of concavity) of the terrain and the distance between the tank and the control point. Having defined the involving variables, a second set of simulations of the simplified scenarios has been carried out and has helped to discuss and develop the curves that are here presented as the final product of the simplified methodology. This methodology only needs some simple calculations and gives a first value of draft and speed by introducing the maximum water level of the tank being evaluated. Subsequently, using the suggested charts, the method gives correction coefficients of the measured values for roughness and average slope of the assessed terrain as well as the degree of concavity (through transverse gradient).With the values from the previous curves (operational draughts and speed at the point of survey) and applying the proposed formulation, an estimation of the risk associated to the breakage of the infrastructure is finally obtained. As a corollary of the mentioned methodology, another set of diagrams is proposed in order to evaluate, in a simplified manner also, the risk reduction that could be gained with the construction of some mitigating measures such as dikes or retaining walls around the reservoir. This evaluating method provides a guide to analyse the possibility to reduce the risk, constructing those elements or even looking for a different site that could be worse in terms of exploitation of the tank but much safer. As a complement to the simplified methodology here proposed, and apart from completing its calibration with the obtained data after the reservoir breakage in Melilla, a number of examples of the use of the methodology have been made to be used as a user guide of the methodology itself, as well as giving the possibility of analysing the different results that can be obtained from a thorough two-dimensional simulation or from the simplified method applied to the examples.

Ventilation and FFFS fire tests for “Calle 30” road tunnels

Between 2003 and 2007 an urban network or road tunnels with a total constructed tubes length of 45 km was built in the city of Madrid. This amazing engineering work, known as "Calle 30 Project" counted with different kinds of tunnel typologies and ventilation systems. Due to the length of the tunnels and the impact of the work itself, the tunnels were endowed with a great variety of installations to provide the maximum levels of safety both for users and the infrastructure includieng, in some parts of the tunnel, fixed fire fighting system based on water mist. Whithin this framework a large-scale programme of fire tests was planned to study different aspects related to fire safety in the tunnels including the phenomena of the interaction between ventilation and extinguishing system. In addition, these large scale fire tests allowed fire brigades of the city of Madrid an opportunity to define operational procedures for specific fire fighting in tunnels and evaluate the possibilities of fixed fire fighting systems. The tests were carried out in the Center of Experimentation "San pedro of Anes" which includes a 600 m tunnel with a removable false ceiling for reproducing different ceiling heights and ventilation conditions (transverse and longitudinal ones). Interesting conclusions on the interaction of ventilation and water mist systems were obtained but also on other aspects including performance of water mist system in terms of reduction of gas temperatures or visibility conditions. This paper presents a description of the test's programme carried out and some previous results obtained.

Large Scale Fire Tests for the “Calle 30 Project"

Between 2003 and 2007 an urban network of road tunnels with a total constructed tubes length of 45 km was built in the city of Madrid. This amazing engineering work, known as “Calle30 Project” counted with different kinds of tunnel typologies and ventilation systems. Due to the length of the tunnels and the impact of the work itself, the tunnels were endowed with a great variety of installations to provide the maximum levels of safety both for users and the infrastructure including,in some parts of the tunnel, fixed fire fighting system based on water mist. Within this framework a large-scale campaign of fire tests were planned to study different aspects related to fire safety in the tunnels including the phenomena of the interaction between ventilation and extinction system. In addition, this large scale fire tests allowed fire brigades of the city of Madrid an opportunity to define operational procedures for specific fire fighting in tunnels and evaluate the possibilities of fixed fire fighting systems. The tests were carried out in the Center of Experimentation "San Pedro of Anes" which counts with a 600 m tunnel with a removable false ceiling for reproducing different ceiling heights and ventilation conditions (transverse and longitudinal ones). Interesting conclusions on the interaction of ventilation and water mist systems were obtained but also on other aspects including performance of water mist system in terms of reduction of gas temperatures or visibility conditions. This paper presents a description of the test’s campaign carried out and some previous results obtained.

Relaciones entre los usos del suelo, las infraestructuras y la planificación: incidencia de la red viaria y el planeamiento en la aparición del terciario para el caso de la N-VI

Esta tesis examina el papel de la red viaria y el planeamiento urbanístico en la localización de las actividades terciarias. A partir de los años sesenta se produce una modificación de los patrones de comportamiento espacial de las actividades productivas. En la raíz de estos cambios está los procesos de globalización e internacionalización de la economía y un importante aumento de la utilización vehículos privados. Todo ello da lugar a una preocupación entre los profesionales por la identificación de variables en esa organización espacial, y por la búsqueda de modelos que mejorasen las condiciones de competitividad en el entramado urbano, reclamado también la formulación de conceptos diferentes, capaces de entender los cambios territoriales de la reestructuración permanente en que viven las economías capitalistas avanzadas. En este marco, hay un aumento importante de las actividades terciarias o proceso de terciarización; que es el principio basilar para la suburbanización de este sector. Consiste, en buena medida, en unas necesidades de descentralización y dispersión de las actividades terciarias por todo el territorio, con demandas de nuevos espacios para todo tipo de actividades empresariales. Se va así generando un espacio urbano complejo, con nuevas actividades, distintas de la residencial, y con tipologías edificatorias diferentes: centros comerciales, hipermercados, zocos o edificios de empresas dedicadas a servicios avanzados y altamente cualificados. Adquiere, por tanto, un fuerte protagonismo los espacios periféricos de las grandes ciudades. En la transformación de este territorio interviene el planeamiento urbanístico porque prevé la ocupación del suelo y la forma de uso. Y también la carretera considerada clave en el desarrollo histórico de la ciudad. Consecuentemente, se impulsan una plétora de nuevas líneas de investigación y nuevas formas de aproximación al estudio de las relaciones entre las infraestructuras viarias y los usos del suelo. El interés del proyecto de investigación es, por todo ello, estudiar en que medida la localización del terciario depende del planeamiento urbano y de las variaciones en la red viaria. Es decir, la hipótesis de este trabajo se puede enunciar diciendo que: en la aparición del terciario inciden dos variables, el planeamiento urbanístico y la red viaria; lógicamente siendo consciente de la dificultad intrínseca de separar algún parámetro y sus relaciones de un sistema funcional urbano. Centrando este enfoque sobre el caso particular del corredor de la carretera de La Coruña (N-VI) situado en el oeste de la Comunidad de Madrid. Es un ámbito suburbano que comprende los términos municipales de Las Rozas y Majadahonda, un segmento del municipio de Madrid (abarca los barrios de Aravaca, el Plantío y Valdemarín, y una pequeña superficie de la Casa de Campo, Ciudad Universitaria y El Pardo), y la mitad septentrional del municipio de Pozuelo de Alarcón. La conclusión general a la que se ha llegado es que se trata de un fenómeno complejo, en el que se detecta que: A) La aprobación de un nuevo Plan Urbanístico no supone un cambio inmediato en la evolución cuantitativa de la implantación de actividades terciarias en edificio exclusivo en el área de estudio. B) Se evidencia una relación directa entre la implantación de una nueva infraestructura de transporte o modificación de algún elemento importante y el crecimiento de la localización de actividades terciarias. C) Resulta difícil verificar que cuando confluyen mejoras o nuevas construcciones en la red viaria y una estrategia en el planeamiento dirigida a la ordenación e intervención del espacio terciario, el número de edificios terciarios aumente. ABSTRACT This thesis examines the role of road networks and urban planning in the location of tertiary activities. Since the sixties there is a modification of spatial behavior patterns of production activities. At the root of these changes is the process of globalization and internationalization of the economy and a significant increase in private car use. This leads to a concern among professionals in the identification of variables in the spatial organization, and the search for models that would improve the competitive conditions in the urban framework, also called for the formulation of different concepts, able to understand the changes territorial restructuring that live permanently in the advanced capitalist economies. In this context, there is a significant increase in tertiary activities or process outsourcing, which is the beginning basilar to the suburbanization of the sector. It consists, in large part, on the Needs of decentralization and dispersal of tertiary activities throughout the territory, demands for new spaces for all types of business activities. It is thus generating a complex urban area, with new activities, other than residential and with different building typologies: shopping malls, hypermarkets, souks and buildings of companies engaged in advanced and highly skilled services. Thus takes strong role peripheral areas of big cities. In the transformation of this region is involved in providing for urban planning land use and how to use. And the road is considered key in the historical development of the city. Consequently, they are promoting a plethora of new research and new ways of approaching the study of the relationship between road infrastructure and land use. The interest of the research project is, for all that, consider to what extent depends on the location of tertiary urban planning and changes in the road network. That is, the hypothesis of this work can be stated by saying that: the emergence of two variables affecting tertiary, urban planning and road network, of course being aware of the inherent difficulty of separating any parameters and functional relationships of an urban. Approach focusing on the particular case of the road corridor from La Coruña (N-VI) located in the west of Madrid. It is a suburban area comprising the municipalities of Las Rozas and Majadahonda, a segment of the city of Madrid (covering the districts of Aravaca, the planting and Valdemarín, and a small area of the Casa de Campo, Ciudad Universitaria and El Pardo) , and the northern half of the town of Pozuelo de Alarcón. The general conclusion has been reached is that this is a complex phenomenon, which is detected: A) The approval of a new Urban Plan is not an immediate change in the quantitative evolution of the implementation of tertiary activities in exclusive building in the study area. B) It shows a direct relationship between the introduction of a new transport infrastructure or amendment to an important and growing element of the location of tertiary activities. C) It is difficult to verify that when improvements or new construction come together in the road network and planning a strategy aimed at the management and intervention of third space, the number of commercial buildings increases.

Rebalancing urban mobility: a tale of four cities

The key of mobility in urban planning is not in dispute. Integrated strategies that take into account the interrelations among land use, transport supply and demand and the different transportation modes are more necessary than ever. In Europe, regulatory tools such as local mobility plans or traffic plans have been enforced for a long time, evolving into so-called sustainable urban transport plans (SUTP) ? that is, plans thatmerge urban planning,mobility governance, social awareness and environmental safeguards to develop a vision based on sustainability and equity. Indeed, SUTP are aimed at solving typical problems in current land use, such as urban sprawl, which make clear the need for a paradigm shift from transport (or mobility) planning to land use (or city) planning, thereby producing urban mobility plans that are fully aligned with integrated urban development plans. This paper describes how SUTP are articulated across Europe according to four case studies: Peterborough (UK), Chambe¿ry (France), Ferrara (Italy) and Pinto (Spain), to highlight variations and commonalities, both among the four national legal frameworks and the actual planning processes at the local level. Objectives, measures and indicators used in the monitoring and evaluation phases have been analysed and the results assessed. The main conclusion of the paper is that, as seen in these real-life examples, the lack of integration between spatial planning and transport strategies results in the unsustainability of urban areas and, therefore, in a significant loss of competitiveness.

Management of Urban Mobility to Control Climate Change in Cities

The need of decarbonization of urban mobility is one of the main priorities for all countries to achieve greenhouse gas (GHG) emissions reduction targets. In general, the transport modes which have experienced the most growth in recent years tend to be the most polluting. Most efforts have been focused on the vehicle efficiency improvements and vehicle fleet renewal; nevertheless more emphasis should be placed on strategies related to the management of urban mobility and modal share. Research of individual travel which analyzes CO2 emissions and car and public transport share in daily mobility will enable better assessments of the potential of urban mobility measures introduced to limit GHG emissions produced by transport in cities. This paper explores the sustainability impacts of daily mobility in Spain using data from two National Travel Surveys (NTSs) (2000 and 2006) and includes a method by which to estimate the CO2 emissions associated with each journey and each surveyed individual. The results demonstrate that in the 2000 to 2006 period, there has been an increase in daily mobility which has led to a 17% increase in CO2 emissions. When separated by transport mode, cars prove to be the main contributor to that increase, followed by public transport. More focus should be directed toward modal shift strategies which not only take the number of journeys into account but also consider distance. The contributions of this paper have potential applications in the assessment of current and future urban transport policies.

Management of urban mobility to control climate change in cities in Spain

The need to decarbonize urban mobility is one of the main motivations for all countries to achieve reduction targets for greenhouse gas (GHG) emissions. In general, the transport modes that have experienced the most growth in recent years tend to be the most polluting. Most efforts have focused on improvements in vehicle efficiency and on the renewal of vehicle fleets; more emphasis should be placed on strategies related to the management of urban mobility and modal share. Research of individual travel that analyzes carbon dioxide (CO2) emissions and car and public transport share in daily mobility will enable better assessments of the potential of urban mobility measures introduced to limit GHG emissions produced by transport in cities. The climate change impacts of daily mobility in Spain are explored with data from two national travel surveys in 2000 and 2006, and a method for estimating the CO2 emissions associated with each journey and each surveyed individual is provided. The results demonstrate that from 2000 to 2006, daily mobility has increased and has led to a 17% increase in CO2 emissions. When these results are separated by transport mode, cars prove to be the main contributor to that increase, followed by public transport. More focus should be directed toward modal shift strategies, which take into account not only the number of journeys but also the distance traveled. These contributions have potential applications in the assessment of current and future urban transport policies related to low-carbon urban transportation.

Urban agriculture in the new framework of green cities.

Urban Agriculture was a common practice in the old times. However after a period of low interest by urban population there is a movement of renaissance of urban agriculture especially in the new megalopolis. It is important to understand the role of UA in the new framework, and the interface of urban and rural agricultures, with their comparative advantages. Thus, we describe the impact of UA in several scenarios: political, socioeconomic and environmental. As a consequence several actions should be developed for improving the situation, with the stimulus to UA: urban planning, food value chain, appropriate technology, education and extension services, entertainment and leisure, selection of botanic varieties and agrochemical inputs, design and landscape and good farming practices. As a complement, there is an analysis of the Urban Greening Value Organization in our society. In the paper there is a description of the situation of urban agriculture in Spain (located mainly in roofs, walls, indoor and ground places) the existence of local regulations, barriers and opportunities in the new situation. Due to the social dimension of urban agriculture there are some comments about the role of the more significant stakeholders, and the goals and the structure of the neighbor communities.

Urban trees and atmospheric pollutants in big cities: Effects in Madrid

Una investigación sobre la mejora de la contaminación del aire (CA) por medio de arbolado urbano se realizó en Madrid, una ciudad con casi 4 M de habitantes, 2,8 M de vehículos y casi 3 M de árboles de mantenimiento público. La mayoría de los árboles estaban en dos bosques periurbanos. Los 650.000 restantes era pies de alineación y parques. Los taxones estudiados fueron Platanus orientalis (97.205 árboles), Ulmus sp. (70.557), Pinus pinea (49.038), Aesculus hippocastanum (22.266), Cedrus sp. (13.678) y Quercus ilex (1.650), de calles y parques. Muestras foliares se analizaron en diferentes épocas del año, así como datos de contaminación por PM10 de 28 estaciones de medición de la contaminación durante 30 años, y también la intensidad del tráfico (IMD) en 2.660 calles. La acumulación de metales pesados (MP) sobre hojas y dentro de estas se estimó en relación con la CA y del suelo y la IMD del tráfico. La concentración media de Ba, Cd, Cr, Cu, Mn, Ni, Pb y Zn en suelo (materia seca) alcanzó: 489,5, 0,7, 49,4, 60,9, 460,9, 12,8, 155,9 y 190,3 mg kg-1 respectivamente. Los árboles urbanos, particularmente coníferas (debido a la mayor CA en invierno) contribuyen significativamente a mejorar la CA sobre todo en calles con alta IMD. La capacidad de las seis sp. para capturar partículas de polvo en su superficies foliares está relacionada con la IMD del tráfico y se estimó en 16,8 kg/año de MP tóxicos. Pb y Zn resultaron ser buenos marcadores antrópicos en la ciudad en relación con el tráfico, que fue la principal fuente de contaminación en los árboles y suelos de Madrid. Las especies de árboles variaron en función de su capacidad para capturar partículas (dependiendo de las propiedades de sus superficies foliares) y acumular los MP absorbidos de los suelos. Las concentraciones foliares de Pb y Zn estuvieron por encima de los límites establecidos en diferentes sitios de la ciudad. La microlocalización de Zn mediante microscópico mostró la translocación al xilema y floema. Se detectaron puntos de contaminación puntual de Cu and Cr en antiguos polígonos industriales y la distribución espacial de los MP en los suelos de Madrid mostró que en incluso en zonas interiores del El Retiro había ciertos niveles elevados de [Pb] en suelo, tal vez por el emplazamiento la Real Fábrica de Porcelana en la misma zona hace 200 años. Distintas áreas del centro de la ciudad también alcanzaron niveles altos de [Pb] en suelo. Según los resultados, el empleo de una combinación de Pinus pinea con un estrato intermedio de Ulmus sp. y Cedrus sp. puede ser la mejor recomendación como filtro verde eficiente. El efecto del ozono (O3) sobre el arbolado en Madrid fue también objeto de este estudio. A pesar de la reducción de precursores aplicada en muchos países industrializados, O3 sigue siendo la principal causa de CA en el hemisferio norte, con el aumento de [O3] de fondo. Las mayores [O3] se alcanzaron en regiones mediterráneas, donde el efecto sobre la vegetación natural es compensado por el xeromorfismo y la baja conductancia estomática en respuesta los episodios de sequía estival característicos de este clima. Durante una campaña de monitoreo, se identificaron daños abióticos en hojas de encina parecidos a los de O3 que estaban plantadas en una franja de césped con riego del centro de Madrid. Dada la poca evidencia disponible de los síntomas de O3 en frondosas perennifolias, se hizo un estudio que trató de 1) confirman el diagnóstico de daño de O3, 2) investigar el grado de los síntomas en encinas y 3) analizar los factores ambientales que contribuyeron a los daños por O3, en particular en lo relacionado con el riego. Se analizaron los marcadores macro y micromorfológicos de estrés por O3, utilizando las mencionadas encinas a modo de parcela experimental. Los síntomas consistieron en punteado intercostal del haz, que aumentó con la edad. Además de un punteado subyacente, donde las células superiores del mesófilo mostraron reacciones características de daños por O3. Las células próximas a las zonas dañadas, presentaron marcadores adicionales de estrés oxidativo. Estos marcadores morfológicos y micromorfológicos de estrés por O3 fueron similares a otras frondosas caducifolias con daños por O3. Sin embargo, en nuestro caso el punteado fue evidente con AOT40 de 21 ppm•h, asociada a riego. Análisis posteriores mostraron que los árboles con riego aumentaron su conductancia estomática, con aumento de senescencia, manteniéndose sin cambios sus características xeromórficas foliares. Estos hallazgos ponen de relieve el papel primordial de la disponibilidad de agua frente a las características xeromórficas a la hora de manifestarse los síntomas en las células por daños de O3 en encina. ABSTRACT Research about air pollution mitigation by urban trees was conducted in Madrid (Spain), a southern European city with almost 4 M inhabitants, 2.8 M daily vehicles and 3 M trees under public maintenance. Most trees were located in two urban forests, while 650'000 trees along urban streets and in parks. The urban taxa included Platanus orientalis (97'205 trees), Ulmus sp. (70’557), Pinus pinea (49'038), Aesculus hippocastanum (22’266), Cedrus sp. (13'678 and Quercus ilex (1'650) along streets and parks. Leave samples were analysed sequentially in different seasons, PM10 data from 28 air monitoring stations during 30 years and traffic density estimated from 2’660 streets. Heavy metal (HM) accumulation on the leaf surface and within leaves was estimated per tree related to air and soil pollution, and traffic intensity. Mean concentration of Ba, Cd, Cr, Cu, Mn, Ni, Pb and Zn in topsoil samples (dry mass) amounted in Madrid: 489.5, 0.7, 49.4, 60.9, 460.9, 12.8, 155.9 and 190.3 mg kg-1 respectively. Urban trees, particularly conifers (due to higher pollution in winter) contributed significantly to alleviate air pollution especially near to high ADT roads. The capacity of the six urban street trees species to capture air-born dust on the foliage surface as related to traffic intensity was estimated to 16.8 kg of noxious metals from exhausts per year. Pb and Zn pointed to be tracers of anthropic activity in the city with vehicle traffic as the main source of diffuse pollution on trees and soils. Tree species differed by their capacity to capture air-borne dust (by different leaf surface properties) and to allocate HM from soils. Pb and Zn concentrations in the foliage were above limits in different urban sites and microscopic Zn revelation showed translocation in xylem and phloem tissue. Punctual contamination in soils by Cu and Cr was identified in former industrial areas and spatial trace element mapping showed for central Retiro Park certain high values of [Pb] in soils even related to a Royal pottery 200 years ago. Different areas in the city centre also reached high levels [Pb] in soils. According to the results, a combination of Pinus pinea with understorey Ulmus sp. and Cedrus sp. layers can be recommended for the best air filter efficiency. The effects of ozone (O3) on trees in different areas of Madrid were also part of this study. Despite abatement programs of precursors implemented in many industrialized countries, ozone remained the main air pollutant throughout the northern hemisphere with background [O3] increasing. Some of the highest ozone concentrations were measured in regions with a Mediterranean climate but the effect on the natural vegetation is alleviated by low stomatal uptake and frequent leaf xeromorphy in response to summer drought episodes characteristic of this climate. During a bioindication survey, abiotic O3-like injury was identified in foliage. Trees were growing on an irrigated lawn strip in the centre of Madrid. Given the little structural evidence available for O3 symptoms in broadleaved evergreen species, a study was undertaken in 2007 with the following objectives 1) confirm the diagnosis, 2) investigate the extent of symptoms in holm oaks growing in Madrid and 3) analyse the environmental factors contributing to O3 injury, particularly, the site water supply. Therefore, macro- and micromorphological markers of O3 stress were analysed, using the aforementioned lawn strip as an intensive study site. Symptoms consisted of adaxial and intercostal stippling increasing with leaf age. Underlying stippling, cells in the upper mesophyll showed HR-like reactions typical of ozone stress. The surrounding cells showed further oxidative stress markers. These morphological and micromorphological markers of ozone stress were similar to those recorded in deciduous broadleaved species. However, stippling became obvious already at an AOT40 of 21 ppm•h and was primarily found at irrigated sites. Subsequent analyses showed that irrigated trees had their stomatal conductance increased and leaf life-span reduced whereas their leaf xeromorphy remained unchanged. These findings suggest a central role of water availability versus leaf xeromorphy for ozone symptom expression by cell injury in holm oak.

Study of PM10 and PM2.5 levels in three European cities: Analysis of intra and inter urban variations

In the present paper, 1-year PM10 and PM 2.5 data from roadside and urban background monitoring stations in Athens (Greece), Madrid (Spain) and London (UK) are analysed in relation to other air pollutants (NO,NO2,NOx,CO,O3 and SO2)and several meteorological parameters (wind velocity, temperature, relative humidity, precipitation, solar radiation and atmospheric pressure), in order to investigate the sources and factors affecting particulate pollution in large European cities. Principal component and regression analyses are therefore used to quantify the contribution of both combustion and non-combustion sources to the PM10 and PM 2.5 levels observed. The analysis reveals that the EU legislated PM 10 and PM2.5 limit values are frequently breached, forming a potential public health hazard in the areas studied. The seasonal variability patterns of particulates varies among cities and sites, with Athens and Madrid presenting higher PM10 concentrations during the warm period and suggesting the larger relative contribution of secondary and natural particles during hot and dry days. It is estimated that the contribution of non-combustion sources varies substantially among cities, sites and seasons and ranges between 38-67% and 40-62% in London, 26-50% and 20-62% in Athens, and 31-58% and 33-68% in Madrid, for both PM10 and PM 2.5. Higher contributions from non-combustion sources are found at urban background sites in all three cities, whereas in the traffic sites the seasonal differences are smaller. In addition, the non-combustion fraction of both particle metrics is higher during the warm season at all sites. On the whole, the analysis provides evidence of the substantial impact of non-combustion sources on local air quality in all three cities. While vehicular exhaust emissions carry a large part of the risk posed on human health by particle exposure, it is most likely that mitigation measures designed for their reduction will have a major effect only at traffic sites and additional measures will be necessary for the control of background levels. However, efforts in mitigation strategies should always focus on optimal health effects.