Flammability properties of thermally dried sewage sludge

The treatment and disposal of sewage sludge is becoming an urgent need whereby different technologies were developed and integrated into the waste cycle all over the world. One of the most used technologies is the thermal drying of the sludge. Thermally dried sewage sludge has interesting properties that allow its use as an alternative fuel, but also needs some consideration from the point of view of its safe operation. The aim of this study was the research on the flammability properties of sewage sludge, including ignition sensitivity, explosion severity, thermal sensitivity and thermal stability. Furthermore relationships among those properties and composition parameters have been determined, added to the study of their variation depending on their origin or season. Finally, properties related to spontaneous combustion were determined. To study these relationships and characteristics sludge samples were selected from different locations in Spain and taken during different seasons.

Behaviour of dolomite, olivine and alumina as primary catalysts in air-steam gasification of sewage sludge

Sewage sludge gasification assays were performed in an atmospheric fluidised bed reactor using air and air–steam mixtures as the gasifying agents. Dolomite, olivine and alumina are three well known tar removal catalysts used in biomass gasification processing. However, little information is available regarding their performance in sewage sludge gasification. The aim of the current study was to learn about the influence of these three catalysts in the product distribution and tar production during sewage sludge gasification. To this end, a set of assays was performed in which the temperature (750–850 °C), the in-bed catalyst content (0, 10 and 15 wt.%) and the steam–biomass ratio (SB) in the range of 0–1 were varied with a constant equivalence ratio (ER) of 0.3. The results were compared to the results from gasification without a catalyst. We show that dolomite has the highest activity in tar elimination, followed by alumina and olivine. In addition to improving tar removal, the presence of water vapour and the catalysts increased the content of H2 in the gases by nearly 60%.

Air-steam gasification of sewage sludge in a bubbling bed reactor: Effect of alumina as a primary catalyst

Numerous references can be found in scientific literature regarding biomass gasification. However, there are few works related to sludge gasification. A study of sewage sludge gasification process in a bubbling fluidised bed gasifier on a laboratory scale is here reported. The aim was to find the optimum conditions for reducing the production of tars and gain more information on the influx of different operating variables in the products resulting from the gasification of this waste. The variables studied were the equivalence ratio (ER), the steam-biomass ratio (SB) and temperature. Specifically, the ER was varied from 0.2 to 0.4, the SB from 0 to 1 and the temperature from 750 °C (1023 K) to 850 °C (1123 K). Although it was observed that tar production could be considerably reduced (up to 72%) by optimising the gasification conditions, the effect of using alumina (aluminium oxide, of proven efficacy in destroying the tar produced in biomass gasification) as primary catalyst in air and air-steam mixture tests was also verified. The results show that by adding small quantities of alumina to the bed (10% by weight of fed sludge) considerable reductions in tar production can be obtained (up to 42%) improving, at the same time, the lower heating value (LHV) of the gas and carbon conversion.

Análisis de parámetros de fendas para la estimación de las propiedades mecánicas de vigas de madera de Pinus sylvestris L. Analysis of parameters for assessing drying fissures to estimate their influence on the mechanical properties of Pinus sylvestris L. wooden beams

El principal objetivo de este estudio es evaluar la influencia de las fendas de secado en las propiedades mecánicas de vigas de madera. Para esto, se utilizan 40 vigas de Pino silvestre (Pinus sylvestris L) de 4200 mm de longitud y 150x200 mm de sección que fueron ensayadas según norma EN 408. Las fendas se registran detalladamente atendiendo a su longitud y posición en cada cara de la viga, y midiendo el espesor y la profundidad cada 100mm a lo largo de la viga. Solo el 10% de la muestra es rechazada por las fendas, según los criterios establecidos por la norma española de clasificación visual UNE 56544. Para evaluar la influencia de las fendas en las propiedades mecánicas, se usan tres parámetros globales basados en el área, el volumen o la profundad de la fenda, y dos locales basados en la profundidad máxima y la profundidad en la zona de rotura. Además se determina la densidad de las piezas. Estos parámetros se comparan con las propiedades mecánicas (tensión de rotura, módulo de elasticidad y energía de rotura) y se encuentra escasa relación entre ellos. Las mejores correlaciones se encuentran entre los parámetros relacionados con la profundidad de las fendas, tanto con el módulo de elasticidad como con la tensión de rotura. The aim of this study is the evaluation of the influence of drying fissures on the mechanical properties of timber beams. For that purpose, 40 sawn timber pieces of Scots pine (Pinus sylvestris L.) with 150x200 mm in cross-section and 4200 mm in length have been tested according to EN 408, obtaining MOR and MOE. The fissures were registered in detail measuring their length and position in each face of the beam, and the thickness and depth every 100 mm in length. Only 10 % of the pieces were rejected because fissures, according to UNE 56544 Spanish visual grading standard. To evaluate the influence of fissures in mechanical properties three global parameters: Fissures Area Ratio or ratio between the area occupied by fissures and the total area in the neutral axis plane of the beam; Fissures Volume Ratio or ratio between volume of fissures and the total volume of the beam; Fissures Average Depth and two local parameters were used: Fissures Maximum Depth in the beam, and Fissures Depth in the broken zone of the beam. Also the density of the beams was registered. These parameters were compared with mechanical properties (tensile strength, elasticity modulus, and rupture energy) and the relationship between them had not been founded. The best relationship was founded between the elasticity modulus y the tensile strength with the parameters which included the depth of the fissures.

Sewage sludge gasification. Dolomite performance under different operating conditions

Gasification is a technology that can replace traditional management alternatives used up to date to deal with this waste (landfilling, composting and incineration) and which fulfils the social, environmental and legislative requirements. The main products of sewage sludge gasification are permanent gases (useful to generate energy or to be used as raw material in chemical synthesis processes), liquids (tars) and char. One of the main problems to be solved in gasification is tar production. Tars are organic impurities which can condense at relatively high temperatures making impossible to use the produced gases for most applications. This work deals with the effect of some primary tar removal processes (performed inside the gasifier) on sewage sludge gasification products. For this purpose, analysis of the gas composition, tar production, cold gas efficiency and carbon conversion were carried out. The tests were performed with air in a laboratory scale plant consisting mainly of a bubbling bed gasifier. No catalyzed and catalyzed (10% wt of dolomite in the bed and in the feeding) tests were carried out at different temperatures (750ºC, 800ºC and 850ºC) in order to know the effect of these parameters in the gasification products. As far as tars were concerned, qualitative and quantitative tar composition was determined. In all tests the Equivalence Ratio (ER) was kept at 0.3. Temperature is one of the most influential variables in sewage sludge gasification. Higher temperatures favoured hydrogen and CO production while CO2 content decreased, which might be partially explained by the effect of the cracking, Boudouard and CO2 reforming reactions. At 850ºC, cold gas efficiency and carbon conversion reached 49% and 76%, respectively. The presence of dolomite as catalyst increased the production of H2 reaching contents of 15.5% by volume at 850 °C. Similar behaviour was found for CO whereas CO2 and CnHm (light hydrocarbons) production decreased. In the presence of dolomite, a tar reduction of up to 51% was reached in comparison with no catalyzed tests, as well as improvements on cold gas efficiency and carbon conversion. Several assays were developed in order to test catalyst performance under more rough gasification conditions. For this purpose, the throughput value (TR), defined as kg sludge “as received” fed to the gasifier per hour and per m2 of cross sectional area of the gasifier, was modified. Specifically, the TR values used were 110 (reference value), 215 and 322 kg/h·m2. When TR increased, the H2, CO and CH4 production decreased while the CO2 and the CnHm production increased. Tar production increased drastically with TR during no catalysed tests what is related to the lower residence time of the gas inside the reactor. Nevertheless, even at TR=322 kg/h·m2, tar production decreased by nearly 50% with in-bed use of dolomite in comparison with no catalyzed assays under the same operating conditions. Regarding relative tar composition, there was an increase in benzene and naphthalene content when temperature increased while the content of the rest of compounds decreased. The dolomite seemed to be effective all over the range of molecular weight studied showing tar removal efficiencies between 35-55% in most cases. High values of the TR caused a significant increase in tar production but a slight effect on tar composition.

Sludge treatment system in the city of Wukro (Ethiopia).

This cooperation project aims to improve the sanitation facilities of the city of Wukro (located in the Tigray Region, northern Ethiopia), particularly the management of latrine wastes, by designing a sludge treatment plant in the city. It is framed within the Final Project Department of the E.T.S.I. de Caminos, Canales y Puertos, in collaboration with Wukro’s St. Mary’s College and the Mission of Ángel Olaran, that are part of the Ethiopian Catholic Church Diocese of Adigrat (ECCA). The present city, of about 42,000 inhabitants, was founded by the Italians in 1936. Due to its geographic location, which makes the city suitable for industrial and agricultural activities, Wukro is becoming an important administrative and economic center in the region, with a fast growing population.

Carbon dioxide adsorption in chemically activated carbon from sewage sludge

In this work, sewage sludge was used as precursor in the production of activated carbon by means of chemical activation with KOH and NaOH. The sludge-based activated carbons were investigated for their gaseous adsorption characteristics using CO2 as adsorbate. Although both chemicals were effective in the development of the adsorption capacity, the best results were obtained with solid NaOH (SBAT16). Adsorption results were modeled according to the Langmuir and Freundlich models, with resulting CO2 adsorption capacities about 56 mg/g. The SBAT16 was characterized for its surface and pore characteristics using continuous volumetric nitrogen gas adsorption and mercury porosimetry. The results informed about the mesoporous character of the SBAT16 (average pore diameter of 56.5 Å). The Brunauer-Emmett-Teller (BET) surface area of the SBAT16 was low (179 m2/g) in comparison with a commercial activated carbon (Airpel 10; 1020 m2/g) and was mainly composed of mesopores and macropores. On the other hand, the SBAT16 adsorption capacity was higher than that of Airpel 10, which can be explained by the formation of basic surface sites in the SBAT16 where CO2 experienced chemisorption. According to these results, it can be concluded that the use of sewage-sludge-based activated carbons is a promising option for the capture of CO2. Implications: Adsorption methods are one of the current ways to reduce CO2 emissions. Taking this into account, sewage-sludge-based activated carbons were produced to study their CO2 adsorption capacity. Specifically, chemical activation with KOH and NaOH of previously pyrolyzed sewage sludge was carried out. The results obtained show that even with a low BET surface area, the adsorption capacity of these materials was comparable to that of a commercial activated carbon. As a consequence, the use of sewage-sludge-based activated carbons is a promising option for the capture of CO2 and an interesting application for this waste.

Characterization of spontaneous combustuion tendency of dried sewage sludge

The general purpose of this study was the determination of the safety conditions to avoid the presence of explosive atmospheres in the wastewater industry. Eight Spanish plants located in Madrid, Barcelona and Málaga were considered and several sludge samples were taken in different seasons. The base for the assessment of the spontaneous ignition behaviour of dust accumulations is the experimental determination of the self-ignition temperature under isothermal conditions. Self-ignition temperatures at four volumes were obtained for one sample of sewage sludge, allowing their extrapolation to large storage facilities. A simple test method, based also on an isothermal study of samples, is the UN classification of substances liable to spontaneous combustion. Two different samples were so tested, obtaining unlike results if transported in packages of different volumes. By means of thermogravimetric techniques it is possible to analyse the thermal susceptibility of dried sewage sludge. Apparent activation energy can be obtained from the rate of weight loss. It is also applied to the study of self-ignition susceptibility by modifying test conditions when oxygen stream is introduced. As a consequence of this oxidant contribution, sample behaviour can be very different during testing and a step drop or sudden loss of weight is observed at a characteristic temperature for every substance, associated to a rapid combustion. Plotting both the activation energy and the characteristic temperature, a map of self-ignition risk was obtained for 10 samples, showing different risk levels for samples taken in different locations and at different seasons. A prediction of the self-ignition risk level can be also determined.

Optimización de la aplicación de lodos de depuración de aguas residuales al abonado o mejora de suelos

El objetivo de este trabajo de investigación fue evaluar el efecto de la aplicación de lodos residuales procedentes de una planta de tratamiento de aguas residuales acondicionados como biosólido para el abonado de tres cultivos agrícolas. Esto se realizó a través del estudio de las variables de producción (desarrollo vegetal de cada cultivo) y de la comparación de las características de los suelos utilizados antes y después de los ensayos experimentales. A través de la investigación se confirmó la mejora en la calidad del suelo y mejor rendimiento de cultivo debido a los biosólidos procedentes de tratamiento de aguas residuales. Este trabajo de investigación de tipo descriptivo y experimental, utilizó lodos optimizados que fueron aplicados a tres cultivos agrícolas de ciclo corto. Fueron evaluados dos cultivos (sandía y tomate) bajo riego y un cultivo (arroz) en secano. En la primera fase del trabajo se realizó la caracterización de los lodos, para ellos se realizaron pruebas físico químicas y microbiológicas. Fue utilizado el método de determinación de metales por espectrometría de emisión atómica de plasma acoplado inductivamente, (ICP-AES) para conocer las concentraciones de metales. La caracterización microbiológica para coliformes totales y fecales se realizó utilizando la técnica del Número más probable (NMP), y para la identificación de organismos patógenos se utilizó el método microbiológico propuesto por Kornacki & Johnson (2001), que se fundamenta en dos procesos: pruebas presuntivas y prueba confirmativa. Tanto los resultados para la determinación de metales y elementos potencialmente tóxicos; como las pruebas para la determinación de microorganismos potencialmente peligrosos, estuvieron por debajo de los límites considerados peligrosos establecidos por la normativa vigente en Panama (Reglamento Técnico COPANIT 47-2000). Una vez establecido la caracterización de los lodos, se evalúo el potencial de nutrientes (macro y micro) presentes en los biosólidos para su potencial de uso como abono en cultivos agrícolas. El secado de lodos fue realizado a través de una era de secado, donde los lodos fueron deshidratados hasta alcanzar una textura pastosa. “La pasta de lodo” fue transportada al área de los ensayos de campo para continuar el proceso de secado y molida. Tres ensayos experimentales fueron diseñados al azar con cinco tratamientos y cuatro repeticiones para cada uno de los tres cultivos: sandía, tomate, arroz, en parcelas de 10m2 (sandía y tomate) y 20 m2 (arroz) para cada tratamiento. Tres diferentes dosis de biosólidos fueron evaluadas y comparadas con un tratamiento de fertilizante comercial y un tratamiento control. La dosis de fertilizante comercial utilizada en cada cultivo fue la recomendada por el Instituto de Investigación Agropecuaria de Panamá. Los ensayos consideraron la caracterización inicial del suelo, la preparación del suelo, semilla, y arreglo topográfico de los cultivos siguiendo las recomendaciones agronómicas de manejo de cultivo establecida por el Instituto de Investigación Agropecuaria. Para los ensayos de sandía y tomate se instaló el sistema de riego por goteo. Se determinaron los ácidos húmicos presentes en los cultivos, y se estudiaron las variables de desarrollo de cada cultivo (fructificación, cosecha, peso de la cosecha, dimensiones de tamaño y color de las frutas, rendimiento, y la relación costo – rendimiento). También se estudiaron las variaciones de los macro y micro nutrientes y las variaciones de pH, textura de suelo y MO disponible al inicio y al final de cada uno de los ensayos de campo. Todas las variables y covariables fueron analizadas utilizando el programa estadístico INFOSAT (software para análisis estadístico de aplicación general) mediante el análisis de varianza, el método de comparaciones múltiples propuesto por Fisher (LSD Fisher) para comparar las medias de los cultivares y el coeficiente de correlación de Pearson que nos permite analizar si existe una asociación lineal entre dos variables. En la evaluación de los aportes del biosólido a los cultivos se observó que los macronutrientes N y P se encontraban de los límites requeridos en cada uno de los cultivos, pero que los niveles de K estuvieron por debajo de los requerimientos de los cultivos. A nivel de la fertilización tradicional con fertilizante químico se observó que la dosis recomendada para cada uno de los cultivos del estudio estaba sobreestimada en los tres principales macronutrientes: Nitrógeno, Fosforo y Potasio. Contenían concentraciones superiores de N, P y K a las requeridas teóricamente por el cultivo. El nutriente que se aporta en exceso es el Fósforo. Encontramos que para el cultivo de sandía era 18 veces mayor a lo requerido por el cultivo, en tomate fue 12 veces mayor y en el cultivo de arroz, 34 veces mayor. El fertilizante comercial tuvo una influencia en el peso final y rendimiento final en cada uno de los cultivos del estudio. A diferencia, los biosólidos tuvieron una influencia directa en el desarrollo de los cultivos (germinación, coloración, tamaño, longitud, diámetro, floración y resistencia a enfermedades). Para el caso de la sandía la dosis de biosólido más cercana al óptimo para el cultivo es la mayor dosis aplicada en este ensayo (97.2 gramos de biosólido por planta). En el caso de tomate, el fertilizante comercial obtuvo los mejores valores, pero las diferencias son mínimas con relación al tratamiento T1, de menor dosis de biosólido (16.2 gramos de biosólido por planta). Los resultados generales del ensayo de tomate estuvieron por debajo del rendimiento esperado para el cultivo. Los tratamientos de aplicación de biosólidos aportaron al desarrollo del cultivo en las variables tamaño, color y resistencia a las enfermedades dentro del cultivo de tomate. Al igual que el tomate, en el caso del arroz, el tratamiento comercial obtuvo los mejores resultados. Los resultados finales de peso y rendimiento del cultivo indican que el tratamiento (T2), menor dosis de biosólido (32.4 gramos por parcela), no tuvo diferencias significativas con los resultados obtenidos en las parcelas con aplicación de fertilizante comercial (T1). El tratamiento T4 (mayor dosis de biosólido) obtuvo los mejores valores para las variables germinación, ahijamiento y espigamiento del cultivo, pero al momento de la maduración obtuvo los menores resultados. Los biosólidos aportan nutrientes a los cultivos y al final del ensayo se observó que permanecen disponibles en el suelo, aportando a la mejora del suelo final. En los tres ensayos, se pudo comprobar que los aportes de los biosólidos en el desarrollo vegetativo de los cultivos. También se encontró en todos los ensayos que no hubo diferencias significativas (p > 0.05) entre los tratamientos de biosólidos y fertilizante comercial. Para obtener mejores resultados en estos tres ensayos se requeriría que a la composición de biosólidos (utilizada en este ensayo) se le adicione Potasio, Calcio y Magnesio en las cantidades requeridas por cada uno de los cultivos. ABSTRACT The objective of this investigation was to evaluate the effect of residual sewage sludge obtained from the residual water of a treatment plant conditioned as Biosolid used on three reliable agricultural crops. The effect of the added sewage sludge was evaluated through the measurement of production variables such as crop plant development and the comparison of the soil characteristics used before and after the experimental tests. This investigation confirmed that biosolids from wastewater treatment can contribute to the growth of these crops. In this experimental approach, optimized sludge was applied to three short-cycle crops including two low-risk crops (watermelon and tomato) and one high-risk crop (rice) all grown on dry land. In the first phase of work, the characteristics of the sludge were assessed using chemical, physical and microbiological tests. The concentrations of metals were determined by atomic emission spectrometry inductively coupled plasma, (ICP-AES). Microbiological characterization was performed measuring total coliform and fecal count using the most probable number technique (NMP) and microbiological pathogens were identified using Kornacki & Johnson (2001) method based on two processes: presumptive and confirmatory tests. Both the results for the determination of metals and potentially toxic elements, as testing for the determination of potentially dangerous microorganisms were below the limits established by the applicable standard in Panama (Technical Regulate COPANIT 47-2000). After the metal and bacterial characterization of the sludge, the presence of macro or micronutrients in biosolids was measured to evaluate its potential for use as fertilizer in the growth of agricultural crops. The sludge was dehydrated via a drying process into a muddy slurry. The pulp slurry was transported to the field trial area to continue the process of drying and grinding. Three randomized experimental trials were designed to test with five treatment regimens and four replications for each of the crops: watermelon, tomato, rice. The five treatment regimens evaluated were three different doses of bio solid with commercial fertilizer treatment control and no fertilizer treatment control. Treatment areas for the watermelon and tomato were 10m2 plots land and for rice was 20m2. The amount of commercial fertilizer used to treat each crop was based on the amount recommended by Agricultural Research Institute of Panama. The experimental trials considered initial characterization of soil, soil preparation, seed, and crop topographical arrangement following agronomic crop management recommendations. For the tests evaluating the growth of watermelons and tomatoes and drip irrigation system was installed. The amount of humic acids present in the culture were determined and developmental variable of each crop were studied (fruiting crop harvest weight, size dimensions and color of the fruit, performance and cost effectiveness). Changes in macro and micronutrients and changes in pH, soil texture and OM available were measured at the beginning and end of each field trial. All variables and covariates were analyzed using INFOSAT statistical program (software for statistical analysis of general application) by analysis of variance, multiple comparisons method as proposed by Fisher (LSD Fisher) to compare the means of cultivars and the Pearson ratio that allows us to analyze if there is a linear association between two variables. In evaluating the contribution of biosolids to agricultural crops, the study determined that the macronutrients N & P were within the requirements of crops, but K levels were below the requirements of crops. In terms of traditional chemical fertilizer fertilization, we observed that the recommended dose for each study crop was overestimated for the three major nutrients: nitrogen, phosphorus and potassium. Higher concentrations containing N, P and K to the theoretically required by the crop. The recommended dose of commercial fertilizer for crops study contained greater amounts of phosphorus, crops that need. The level of phosphorous was found to be18 times greater than was required for the cultivation of watermelon; 12 times higher than required for tomato, and 34 times higher than required for rice cultivation. Phosphorus inputs of commercial fertilizer were a primary influence on the weight and performance of each crop. Unlike biosolids had a direct influence on crop development (germination, color, size, length, diameter, flowering and disease resistance). In the case of growth of watermelons, the Biosolid dose closest to the optimum for cultivation was applied the highest dose in this assay (97.2 grams of bio solids per plant). In the case of tomatoes, commercial fertilizer had the best values but the differences were minimal when compared to treatment T1, the lower dose of sewage sludge (Biosolid 16.2 grams per plant). The overall results for the tomato crop yield of the trial were lower than expected. Additionally, the application of biosolids treatment contributed to the development of fruit of variable size, color and disease resistance in the tomato crops. Similar to the tomato crop, commercial fertilizer treatment provided the best results for the rice crop. The final results of weight and crop yield for rice indicated that treatment with T2 amount of biosolids (34.2 grams per plot) was not significantly different from the result obtained in the application plot given commercial fertilizer (T1). The T4 (higher dose of bio solid) treatment had the best values for the germination, tillering and bolting variables of the rice crop but for fruit ripening yielded lower results. In all three trials, biosolids demonstrated the ability to contribute in the vegetative growth of crops. It was also found in all test no significant differences (p>0.05) between treatment of bio solid and commercial fertilizer. Biosolids provided nutrients to the crops and even at the end of the trial remained available in the ground soil, contributing to the improvement of the final ground. The best results from these three trials is that the use of bio solids such as those used in this assay would require the addition of potassium, calcium and magnesium in quantities required for each crop.