Plataforma de simulación en Matlab-Simulink de un accionamiento regulado para emular aerogeneradores

En este proyecto se desarrolla un modelo de simulación de un accionamiento controlado que emula el comportamiento de una turbina eólica, el cual se ha llevado a cabo a través del programa para simulación Matlab/Simulink. Su desarrollo se ha estructurado de la siguiente forma: Tras una breve introducción a la energía eólica y a las máquinas eléctricas objeto de estudio en este proyecto, se procede a la caracterización y representación de dichas maquinas dentro de la plataforma de simulación virtual Simulink. Posteriormente se explican posibles estrategias de control de la máquina de inducción, las cuales son aplicadas para la realización de un control de velocidad. Asimismo, se realiza un control vectorial de par de la máquina de inducción de modo que permita un seguimiento efectivo del par de referencia demandado por el usuario, ante distintas condiciones. Finalmente, se añade el modelo de turbina eólica de manera que, definiendo los valores de velocidad de viento, ángulo de paso y velocidad del eje, permite evaluar el par mecánico desarrollado por la turbina. Este modelo se valida comprobando su funcionamiento para diferentes puntos de operación ante diversas condiciones del par de carga. Las condiciones de carga se establecen acoplando al modelo de la turbina, un generador síncrono de imanes permanentes conectado a una carga resistiva. ! II! ABSTRACT In this project, the simulation model of a controlled drive that emulates the behaviour of a wind turbine is developed. It has been carried out through the platform for multidomian simulation called Matlab/Simulink. Its development has been structured as follows: After a brief introduction to the wind energy and the electrical machines studied in this project, these machines are characterized and represented into the virtual simulation platform, Simulink. Subsequently, the possible control strategies for the induction machine are explained and applied in order to carry out a speed control. Additionally, a torque vector control of the induction machine is performed, so as to enable an effective monitoring of the reference torque requested by the user, under different conditions. Finally, the wind turbine model is implemented so as to assess the turbine mechanical torque, after defining the wind speed, the pitch angle and the shaft speed values. This model is validated by testing its functionality for different operating points under various load torques. The load conditions are set up by attaching a permanent magnets synchronous machine, with a resistive load, to the turbine model.

Wind turbine wakes for wind energy

During recent years, wind energy has moved from an emerging technology to a nearly competitive technology. This fact, coupled with an increasing global focus on environmental concern and a political desire of a certain level of diversification in the energy supply, ensures wind energy an important role in the future electricity market. For this challenge to be met in a cost-efficient way, a substantial part of new wind turbine installations is foreseen to be erected in big onshore or offshore wind farms. This fact makes the production, loading and reliability of turbines operating under such conditions of particular interest.

Analysis of the Behaviour of Biofuel-Fired Gas Turbine Power Plants

The utilisation of biofuels in gas turbines is a promising alternative to fossil fuels for power generation. It would lead to significant reduction of CO2 emissions using an existing combustion technology, although significant changes seem to be needed and further technological development is necessary. The goal of this work is to perform energy and exergy analyses of the behaviour of gas turbines fired with biogas, ethanol and synthesis gas (bio-syngas), compared with natural gas. The global energy transformation process (i.e. from biomass to electricity) has also been studied. Furthermore, the potential reduction of CO2 emissions attained by the use of biofuels has been determined, considering the restrictions regarding biomass availability. Two different simulation tools have been used to accomplish the aims of this work. The results suggest a high interest and the technical viability of the use of Biomass Integrated Gasification Combined Cycle (BIGCC) systems for large scale power generation.

An Experimental and Numerical Study of Ballistic Impacts on a Turbine Casing Material at Varying Temperatures

An experimental and numerical study of ballistic impacts on steel plates at various temperatures (700ºC, 400ºC and room temperature) has been carried out. The motivation for this work is the blade‐off event that may occur inside a jet engine turbine. However, as a first attempt to understand this complex loading process, a somewhat simpler approach is carried out in the present work. The material used in this study is the FV535 martensitic stainless steel, which is one of the most commonly used materials for turbine casings. Based on material test data, a Modified Johnson‐Cook (MJC) model was calibrated for numerical simulations using the LS‐DYNA explicit finite element code (see Figure 1). To check the mesh size sensitivity, 2D axisymmetric finite element models with three different mesh sizes and configurations were used for the various temperatures. Two fixed meshes with 64 and 128 elements over the 2mm thick plate and one mesh with 32 elements over the thickness with adaptive remeshing were used in the simulations. The formation of adiabatic shear bands in the perforation process has been found critical in order to achieve good results. Adiabatic shear bands are formed by the temperature rise due to the accumulation of plastic strain during impact (see Figure 2). The influence of the thermal softening in the plastic model has hence been analyzed for the room temperature impact tests, where the temperature gradient is highest

Implementación de instrumentación virtual con LaBVIEW

El objetivo del PFC es el diseño e implementación de una aplicación que funcione como osciloscopio, analizador de espectro y generador de funciones virtual, todo dentro de la misma aplicacion. Mediante una tarjeta de adquisición de datos tomaremos muestras de señales del mundo real (sistema analógico) para generar datos que puedan ser manipulados por un ordenador (sistema digital). Con esta misma tarjeta también se podrán generar señales básicas, tales como señales senoidales, cuadradas.... y además se ha añadido la funcionalidad de generar señales moduladas en frecuencia, señales tipo Chirp (usadas comúnmente tanto en aplicaciones sonar y radar, como en transmisión óptica) o PRN (ruido pseudo-aleatorio que consta de una secuencia determinista de pulsos que se repite cada periodo, usada comúnmente en receptores GPS), como también señales ampliamente conocidas como el ruido blanco Gaussiano o el ruido blanco uniforme. La aplicación mostrará con detalle las señales adquiridas y analizará de diversas maneras esas señales. Posee la función de enventanado de los tipos de ventana mas comunes, respuesta en frecuencia, transformada de Fourier, etc. La configuración es elegida por el usuario en un entorno amigable y de visualización atractiva. The objective of the PFC is the design and implementation of an application that works as oscilloscope, spectrum analyzer and virtual signal generator, all within the same application. Through a data acquisition card, the user can take samples of real-world signals (analog system) to generate data that can be manipulated by a computer (digital system). This same card can also generate basic signals, such as sine waves, square waves, sawtooth waves.... and further has added other functionalities as frequency modulated signals generation, Chirp signals type generation (commonly used in both sonar and radar applications, such as optical transmission) or PRN (pseudo-random noise sequence comprising a deterministic pulse that repeats every period, commonly used in GPS receivers). It also can generate widely known as Gaussian white noise signals or white noise uniform signals. The application will show in detail the acquired signals and will analyze these signals in different ways selected by the user. Windowing function has the most common window types, frequency response, Fourier transform are examples of what kind of analyzing that can be processed. The configuration is chosen by the user throught friendly and attractive displays and panels.

Comparison of turbulence models for the computational fluid dynamics simulation of wind turbine wakes in the atmospheric boundary layer

An elliptic computational fluid dynamics wake model based on the actuator disk concept is used to simulate a wind turbine, approximated by a disk upon which a distribution of forces, defined as axial momentum sources, is applied on an incoming non-uniform shear flow. The rotor is supposed to be uniformly loaded with the exerted forces estimated as a function of the incident wind speed, thrust coefficient and rotor diameter. The model is assessed in terms of wind speed deficit and added turbulence intensity for different turbulence models and is validated from experimental measurements of the Sexbierum wind turbine experiment.

Sistema de instrumentação e controle para células a combustível

Este trabajo presenta un estudio sobre el funcionamiento y aplicaciones de las células de combustible de membrana tipo PEM, o de intercambio de protones, alimentadas con hidrógeno puro y oxigeno obtenido de aire comprimido. Una vez evaluado el proceso de dichas células y las variables que intervienen en el mismo, como presión, humedad y temperatura, se presenta una variedad de métodos para la instrumentación de tales variables así como métodos y sistemas para la estabilidad y control de las mismas, en torno a los valores óptimos para una mayor eficacia en el proceso. Tomando como variable principal a controlar la temperatura del proceso, y exponiendo los valores concretos en torno a 80 grados centígrados entre los que debe situarse, es realizado un modelo del proceso de calentamiento y evolución de la temperatura en función de la potencia del calentador resistivo en el dominio de la frecuencia compleja, y a su vez implementado un sistema de medición mediante sensores termopar de tipo K de respuesta casi lineal. La señal medida por los sensores es amplificada de manera diferencial mediante amplificadores de instrumentación INA2126, y es desarrollado un algoritmo de corrección de error de unión fría (error producido por la inclusión de nuevos metales del conector en el efecto termopar). Son incluidos los datos de test referentes al sistema de medición de temperatura , incluyendo las desviaciones o error respecto a los valores ideales de medida. Para la adquisición de datos y implementación de algoritmos de control, es utilizado un PC con el software Labview de National Instruments, que permite una programación intuitiva, versátil y visual, y poder realizar interfaces de usuario gráficas simples. La conexión entre el hardware de instrumentación y control de la célula y el PC se realiza mediante un interface de adquisición de datos USB NI 6800 que cuenta con un amplio número de salidas y entradas analógicas. Una vez digitalizadas las muestras de la señal medida, y corregido el error de unión fría anteriormente apuntado, es implementado en dicho software un controlador de tipo PID ( proporcional-integral-derivativo) , que se presenta como uno de los métodos más adecuados por su simplicidad de programación y su eficacia para el control de este tipo de variables. Para la evaluación del comportamiento del sistema son expuestas simulaciones mediante el software Matlab y Simulink determinando por tanto las mejores estrategias para desarrollar el control PID, así como los posibles resultados del proceso. En cuanto al sistema de calentamiento de los fluidos, es empleado un elemento resistor calentador, cuya potencia es controlada mediante un circuito electrónico compuesto por un detector de cruce por cero de la onda AC de alimentación y un sistema formado por un elemento TRIAC y su circuito de accionamiento. De manera análoga se expone el sistema de instrumentación para la presión de los gases en el circuito, variable que oscila en valores próximos a 3 atmosferas, para ello es empleado un sensor de presión con salida en corriente mediante bucle 4-20 mA, y un convertidor simple corriente a tensión para la entrada al sistema de adquisición de datos. Consecuentemente se presenta el esquema y componentes necesarios para la canalización, calentamiento y humidificación de los gases empleados en el proceso así como la situación de los sensores y actuadores. Por último el trabajo expone la relación de algoritmos desarrollados y un apéndice con información relativa al software Labview. ABTRACT This document presents a study about the operation and applications of PEM fuel cells (Proton exchange membrane fuel cells), fed with pure hydrogen and oxygen obtained from compressed air. Having evaluated the process of these cells and the variables involved on it, such as pressure, humidity and temperature, there is a variety of methods for implementing their control and to set up them around optimal values for greater efficiency in the process. Taking as primary process variable the temperature, and exposing its correct values around 80 degrees centigrade, between which must be placed, is carried out a model of the heating process and the temperature evolution related with the resistive heater power on the complex frequency domain, and is implemented a measuring system with thermocouple sensor type K performing a almost linear response. The differential signal measured by the sensor is amplified through INA2126 instrumentation amplifiers, and is developed a cold junction error correction algorithm (error produced by the inclusion of additional metals of connectors on the thermocouple effect). Data from the test concerning the temperature measurement system are included , including deviations or error regarding the ideal values of measurement. For data acquisition and implementation of control algorithms, is used a PC with LabVIEW software from National Instruments, which makes programming intuitive, versatile, visual, and useful to perform simple user interfaces. The connection between the instrumentation and control hardware of the cell and the PC interface is via a USB data acquisition NI 6800 that has a large number of analog inputs and outputs. Once stored the samples of the measured signal, and correct the error noted above junction, is implemented a software controller PID (proportional-integral-derivative), which is presented as one of the best methods for their programming simplicity and effectiveness for the control of such variables. To evaluate the performance of the system are presented simulations using Matlab and Simulink software thereby determining the best strategies to develop PID control, and possible outcomes of the process. As fluid heating system, is employed a heater resistor element whose power is controlled by an electronic circuit comprising a zero crossing detector of the AC power wave and a system consisting of a Triac and its drive circuit. As made with temperature variable it is developed an instrumentation system for gas pressure in the circuit, variable ranging in values around 3 atmospheres, it is employed a pressure sensor with a current output via 4-20 mA loop, and a single current to voltage converter to adequate the input to the data acquisition system. Consequently is developed the scheme and components needed for circulation, heating and humidification of the gases used in the process as well as the location of sensors and actuators. Finally the document presents the list of algorithms and an appendix with information about Labview software.

Analysis of calibration results from cup and propeller anemometers. Influence on wind turbine Annual Energy Production (AEP) calculations

The calibration coefficients of several models of cup and propeller anemometers were analysed. The analysis was based on a series of laboratory calibrations between January 2003 and August 2007. Mean and standard deviation values of calibration coefficients from the anemometers studied were included. Two calibration procedures were used and compared. In the first, recommended by the Measuring network of Wind Energy Institutes (MEASNET), 13 measurement points were taken over a wind speed range of 4 to 16  m  s−1. In the second procedure, 9 measurement points were taken over a wider speed range of 4 to 23  m  s−1. Results indicated no significant differences between the two calibration procedures applied to the same anemometer in terms of measured wind speed and wind turbines' Annual Energy Production (AEP). The influence of the cup anemometers' design on the calibration coefficients was also analysed. The results revealed that the slope of the calibration curve, if based on the rotation frequency and not the anemometer's output frequency, seemed to depend on the cup center rotation radius.

Unidad de efectos de audio en Simulink

La tecnología moderna de computación ha permitido cambiar radicalmente la investigación tecnológica en todos los ámbitos. El proceso general utilizado previamente consistía en el desarrollo de prototipos analógicos, creando múltiples versiones del mismo hasta llegar al resultado adecuado. Este es un proceso costoso a nivel económico y de carga de trabajo. Es por ello por lo que el proceso de investigación actual aprovecha las nuevas tecnologías para lograr el objetivo final mediante la simulación. Gracias al desarrollo de software para la simulación de distintas áreas se ha incrementado el ritmo de crecimiento de los avances tecnológicos y reducido el coste de los proyectos en investigación y desarrollo. La simulación, por tanto, permite desarrollar previamente prototipos simulados con un coste mucho menor para así lograr un producto final, el cual será llevado a cabo en su ámbito correspondiente. Este proceso no sólo se aplica en el caso de productos con circuitería, si bien es utilizado también en productos programados. Muchos de los programas actuales trabajan con algoritmos concretos cuyo funcionamiento debe ser comprobado previamente, para después centrarse en la codificación del mismo. Es en este punto donde se encuentra el objetivo de este proyecto, simular algoritmos de procesado digital de la señal antes de la codificación del programa final. Los sistemas de audio están basados en su totalidad en algoritmos de procesado de la señal, tanto analógicos como digitales, siendo estos últimos los que están sustituyendo al mundo analógico mediante los procesadores y los ordenadores. Estos algoritmos son la parte más compleja del sistema, y es la creación de nuevos algoritmos la base para lograr sistemas de audio novedosos y funcionales. Se debe destacar que los grupos de desarrollo de sistemas de audio presentan un amplio número de miembros con cometidos diferentes, separando las funciones de programadores e ingenieros de la señal de audio. Es por ello por lo que la simulación de estos algoritmos es fundamental a la hora de desarrollar nuevos y más potentes sistemas de audio. Matlab es una de las herramientas fundamentales para la simulación por ordenador, la cual presenta utilidades para desarrollar proyectos en distintos ámbitos. Sin embargo, en creciente uso actualmente se encuentra el software Simulink, herramienta especializada en la simulación de alto nivel que simplifica la dificultad de la programación en Matlab y permite desarrollar modelos de forma más rápida. Simulink presenta una completa funcionalidad para el desarrollo de algoritmos de procesado digital de audio. Por ello, el objetivo de este proyecto es el estudio de las capacidades de Simulink para generar sistemas de audio funcionales. A su vez, este proyecto pretende profundizar en los métodos de procesado digital de la señal de audio, logrando al final un paquete de sistemas de audio compatible con los programas de edición de audio actuales. ABSTRACT. Modern computer technology has dramatically changed the technological research in multiple areas. The overall process previously used consisted of the development of analog prototypes, creating multiple versions to reach the proper result. This is an expensive process in terms of an economically level and workload. For this reason actual investigation process take advantage of the new technologies to achieve the final objective through simulation. Thanks to the software development for simulation in different areas the growth rate of technological progress has been increased and the cost of research and development projects has been decreased. Hence, simulation allows previously the development of simulated protoypes with a much lower cost to obtain a final product, which will be held in its respective field. This process is not only applied in the case of circuitry products, but is also used in programmed products. Many current programs work with specific algorithms whose performance should be tested beforehand, which allows focusing on the codification of the program. This is the main point of this project, to simulate digital signal processing algorithms before the codification of the final program. Audio systems are entirely based on signal processing, both analog and digital systems, being the digital systems which are replacing the analog world thanks to the processors and computers. This algorithms are the most complex part of every system, and the creation of new algorithms is the most important step to achieve innovative and functional new audio systems. It should be noted that development groups of audio systems have a large number of members with different roles, separating them into programmers and audio signal engineers. For this reason, the simulation of this algorithms is essential when developing new and more powerful audio systems. Matlab is one of the most important tools for computer simulation, which has utilities to develop projects in different areas. However, the use of the Simulink software is constantly growing. It is a simulation tool specialized in high-level simulations which simplifies the difficulty of programming in Matlab and allows the developing of models faster. Simulink presents a full functionality for the development of algorithms for digital audio processing. Therefore, the objective of this project is to study the posibilities of Simulink to generate funcional audio systems. In turn, this projects aims to get deeper into the methods of digital audio signal processing, making at the end a software package of audio systems compatible with the current audio editing software.

Implementación del modelo de digestión anaerobia ADM1 en MATLAB/SIMULINK

Este trabajo tiene por objeto la implementación del modelo ADM1 (The IWA Anaerobic Digestion Model No.1), para evaluar su capacidad de simular el proceso de digestión anaerobia de lodos de agua residual. Para implementar el modelo ADM1 se eligió el software Matlab y su herramienta Simulink, por su capacidad para simular sistemas dinámicos. Los resultados demostraron que la simulación a través de la implementación del modelo ADM1, es capaz de predecir la mayoría de los valores medios correspondientes a los parámetros de control más comunes del proceso de digestión anaerobia que se lleva a cabo en la Estación de depuración de aguas residuales (EDAR) sur de Madrid. Se deduce del estudio que la implementación del modelo ADM1 desarrollada mediante Matlab/Simulink, es capaz de simular el proceso dinámico de digestión anaerobia de cualquier EDAR, si se ajustan algunos de los parámetros del modelo para cada caso concreto. Abstract This work aims at the implementation of The IWA Anaerobic Digestion Model No.1 (ADM1) in order to assess its ability to simulate the anaerobic digestion process of wastewater sludge. A Matlab/Simulink implementation of the ADM1 was developed, the simulations results shows that the ADM1 is able to predict the average values of the most common control parameters of the anaerobic digestion process that takes place in the Waste water treatment plant (WWTP) south of Madrid. It is deduced of the estudy that the Matlab implementation of the ADM1 developed, is able to simulate the anaerobic digestion dynamic process of a WWTP, if some of the model parameters are fitted for each specific case.

Diseño de una aplicación labview para la gestión de datos audiométricos

El objetivo principal de este proyecto, es permitir a un amplio conjunto de usuarios, conectarse y mantenerinteracciones con bases de datos audiométricas desde distantes posiciones espaciales. Para ello se procederá al diseño una aplicación en LabVIEW, que permita el acceso de usuarios locales y/o remotos a unas determinadas bases de datos audiométricos. Permitiéndoles la ejecución de una serie de funciones, contra las bases de datos, en función de sus privilegios. Para el desarrollo del diseño se han utilizado las versiones 6.0i y 6.1 de LabVIEW. Para interactuar con las bases de datos, se ha optado por la utilización del lenguaje de comandos para bases de datos denominado SQL. No obstante, como nuestro programa se diseñara en LabVIEW, ha sido necesaria la inclusión del kit de SQL que posee la propia empresa National Intruments para dicho programa. Para la comunicación se emplea el protocolo de transmisión DataSocket que es un protocolo de comunicación punto a punto, que se monta sobre TCP/IP. Este protocolo permite una mayor comodidad y sencillez a la hora de comunicar e interactuar entre dos ordenadores.

The development of a wind tunnel DAQ system by using Labview tools

This paper presents the experimental three-year learning activity developed by a group of teachers in a wind tunnel facility. The authors, leading a team of students, carried out a project consisting of the design, assembly and testing of a wind tunnel. The project included all stages of the process from its initial specifications to its final quality flow assessments, going through the calculation of each element, and the building of the whole wind tunnel. The group of (final year) students was responsible for the whole wind tunnel project as a part of their bachelor degree project. The paper focuses on the development of wind tunnel data acquisition software. This automatic tool is essential to improve the automation of the data acquisition of the wind tunnel facility systems, in particular for a 6DOF multi-axis force/torque sensor. This work can be considered as a typical example of real engineering practice: a set of specifications that has to be modified due to the constraints imposed throughout the project, in order to obtain the final result

Permanent deformation estimates of dynamic equipment foundations: Application to a gas turbine in granular soils

Permanent displacements of a gas turbine founded on a fine, poorly graded, and medium density sand are studied. The amplitudes and modes of vibration are computed using Barkan´s formulation, and the “High-Cycle Accumulation” (HCA) model is employed to account for accumulated deformations due to the high number of cycles. The methodology is simple: it can be easily incorporated into standard mathematical software, and HCA model parameters can be estimated based on granulometry and index properties. Special attention is devoted to ‘transient’ situations at equipment´s start-up, during which a range of frequencies – including frequencies that could be similar to the natural frequencies of the ground – is traversed. Results show that such transient situations could be more restrictive than stationary situations corresponding to normal operation. Therefore, checking the stationary situation only might not be enough, and studying the influence of transient situations on computed permanent displacements is needed to produce a proper foundation design

Validation Study of the Use of Matlab/Simulink Synchronous-Machine Block for Accurate Power-Plant Stability Studies

This paper presents results of the validity study of the use of MATLAB/Simulink synchronous-machine block for power-system stability studies. Firstly, the waveforms of the theoretical synchronous-generator short-circuit currents are described. Thereafter, the comparison between the currents obtained through the simulation model in the sudden short-circuit test, are compared to the theoretical ones. Finally, the factory tests of two commercial generating units are compared to the response of the synchronous generator simulation block during sudden short-circuit, set with the same real data, with satisfactory results. This results show the validity of the use of this generator block for power plant simulation.

Desarrollo de un sistema de control por DSP para regular generadores sincronos de imanes permanentes

En el siguiente proyecto se va a llevar a cabo la simulación en la plataforma Matlb Simulink de una maquina síncrona de imanes permanentes (MSIP) en su funcionamiento como generador, emulando un aerogenerador con tecnología SGFC. El generador tendrá como variable de consigna la velocidad de giro del eje y se ajustara el sistema de control para que sea capaz de seguir la señal de consigna ante cambios bruscos del par. Posteriormente se va a detallar y construir todos los elementos que se consideren necesarios para, en proyectos futuros, llevar a la práctica en una maquina real este sistema de control ABSTRACT The object of this Project is to carry a simulation in Matlab Simulink of a synchronous permanent magnets machine (MSIP) in its operation as a generator, emulating a wind turbine technology SGFC. The variable setpoint will be the rotational speed of the shaft, the control system will fit so that it is capable of following the setpoint signal before sudden changes of the pair. Afterward the elements considered necessary for to put into practice this control system in a real machine will be detailed.