Clasificación visual estructural de la madera de pino radiata procedente de Cataluña

Se han clasificado visualmente, según la norma española UNE 56544; 150 piezas de madera aserrada de pino radiata procedentes de Cataluña (España) con una sección de 80x150 mm y una longitud de 2.500 mm. Esta norma establece dos calidades visuales (ME-1 y ME-2) para piezas con grueso menor o igual que 70 mm y una única calidad visual (MEG) para gruesos mayores de 70 mm. Con el fin de conocer el efecto frontera entre la pequeña y la gran escuadría se clasificaron las piezas según ambas categorías. Se determinó la tensión de rotura en flexión, el módulo de elasticidad en flexión y la densidad de cada pieza mediante el ensayo de acuerdo con la norma UNE-EN 408 siguiendo los ajustes definidos en la norma UNE-EN 384. Un 53 % de las piezas se clasificaron como MEG con una resistencia característica a flexión de 28 N/mm2 y un valor medio del módulo de elasticidad de 9.900 N/mm2. Por otra, un 42 % de las piezas se clasificaron como ME-2 y sólo un 3 % como ME-1; en este caso las propiedades mecánicas de la calidad ME-2 no se alejan mucho de las de la calidad MEG. El elevado porcentaje de piezas rechazadas (47 % frente a la MEG) se debe principalmente al defecto de alabeo responsable de un 39 % de rechazo. Si no se considera el alabeo en la clasificación el porcentaje de rechazo desciende al 17 % y las propiedades mecánicas de la calidad MEG presentan un valor característico de resistencia a flexión de 21 N/mm2 y un módulo de elasticidad de 9.100 N/mm2. A sample of 150 pieces of radiata pine sawn timber with 180x120 mm in cross-section and 2.500 mm in length sourcing from Catalonia (Spain) were visually graded according to Spanish standard UNE 56544. This standard establish two visual grades (ME-1 and ME-2) for timber pieces with thickness equal or less than 70 mm, and one grade (MEG) for thickness bigger than 70 mm. In order to know the border effect between small and larger cross-section the pieces were graded in both categories. The modulus of rupture, modulus of elasticity and density were obtained by test according to EN 408 standard and the adjustments of EN 384. A 53 % of pieces were classified as MEG with a characteristic bending strength of 28 N/mm2 and a mean value of MOE of 9.900 N/mm2. On the other hand, a 42 % of pieces were classified as ME-2 and only a 3 % as ME-1; in this case the mechanical properties of ME-2 are not far from MEG properties. The high percentage of rejected pieces (47 % vs MEG) is mainly due to the twist defect with a 39 % of rejected pieces. If twist is not considered in the grading process the reject percentage decreases to 17 % and the mechanical properties of MEG grade present a characteristic value of bending strength of 21 N/mm2 and a MOE of 9.100 N/mm2.

Discriminant Analysis of Geographical Origin of Cork Planks and Stoppers by Near Infrared Spectroscopy

The objective of this study was to assess the potential of visible and near infrared spectroscopy (VIS+NIRS) combined with multivariate analysis for identifying the geographical origin of cork. The study was carried out on cork planks and natural cork stoppers from the most representative cork-producing areas in the world. Two training sets of international and national cork planks were studied. The first set comprised a total of 479 samples from Morocco, Portugal, and Spain, while the second set comprised a total of 179 samples from the Spanish regions of Andalusia, Catalonia, and Extremadura. A training set of 90 cork stoppers from Andalusia and Catalonia was also studied. Original spectroscopic data were obtained for the transverse sections of the cork planks and for the body and top of the cork stoppers by means of a 6500 Foss-NIRSystems SY II spectrophotometer using a fiber optic probe. Remote reflectance was employed in the wavelength range of 400 to 2500 nm. After analyzing the spectroscopic data, discriminant models were obtained by means of partial least square (PLS) with 70% of the samples. The best models were then validated using 30% of the remaining samples. At least 98% of the international cork plank samples and 95% of the national samples were correctly classified in the calibration and validation stage. The best model for the cork stoppers was obtained for the top of the stoppers, with at least 90% of the samples being correctly classified. The results demonstrate the potential of VIS + NIRS technology as a rapid and accurate method for predicting the geographical origin of cork plank and stoppers

Gas discharges for continental Spain: geochemical and isotopic features

In this work the results of a geochemical and isotopic survey of 37 gas discharges was carried out in continental Spain are presented and discussed. On the basis of the gas chemical composition, four different areas can be distinguished, as follows: 1) Selva-Emborda (SE) region; 2) Guadalentin Valley (GV); 3) Campo de Calatrava (CC) and 3) the inner part of Spain (IS). The SE, GV and CC areas are characterized by CO2-rich gases, while IS has N2 as main gas compound. The CO2-rich gases can be distinguished at their turn on the basis on the helium and carbon isotopic composition. The SE and CC areas have a strong mantle signature (up to 3 Ra). Nevertheless, the carbon isotopic composition of CC is within the mantle range and that of SE is slightly more negative (down to -8‰ PDB). The GV gases have a lower mantle signature (61 Ra) with respect to SE and CC and more negative carbon isotopes (6-10‰ PDB). It is worth to mention that the SE, GV and CC areas are related to the youngest volcanic activity in continental Spain, for example the Garrotxa Volcanic Field in Catalonia records the latest event dated at 10,000 years, and the isotopic features, particularly those of helium, are suggesting the presence of magmatic bodies still cooling at depth. The N2-rich gases, i.e. those from the IS area, has an atmospheric origin, as highlighted by the N2/Ar ratio that ranges between those of air and ASW (Air Saturated Water). The isotopic composition of carbon is distinctly negative (down to -21‰ PDB) and that of helium is typically crustal (0.02-0.08 Ra), confirming that these gas discharges are related to a relatively shallow source.

The spanish professional soccer foundations. (Las fundaciones clubes de futbol profesionales en España)

Sports foundations aiming at promoting sports activities partly outline the nonprofit area with specific concern. This study attempts to know the functions, general interests of professional soccer foundations in Spain, to describe their main characteristics and to ascertain if there are significant differences among them, according to their descriptive features. A document survey and analysis was carried out, with an assistance of own establishment of documental database. The findings not only indicate a significant difference between the classification of Spanish soccer foundations and their antiquities, but also manifest the tendency of the existence of physical person in members of founders with regard to its antiquity. The results of the present work implied that there were great dissimilarities of the elaboration of regulations depending on different regions in Spain.

Quantification of impacts in artistic gymnastics with accelerometry: an approximation

Intensity and volume of training in Artisti Gymnastics are increasing as the sooner athlete's age of incorporation creating some disturbance in them.

First steps of Roman Cement in Spain

Natural cement was patented in 1796 but it didn’t arrive in Spain until 1835. No one knows exactly where the production started in Spain, because it emerged independently at the same time in many places. Most of these outbreaks are concentrated in the north and northwest of Spain: Basque Country (Zumaya and Rezola) and Catalonia (San Celoní and San Juan de las Abadesas).Natural cement was extensively used to decorate historical buildings during the nineteenth and beginning of twentieth century in Madrid. It was the building material which realised the architects and builders dreams of mass-produced cast elements in a wide variety of styles. Its arrival replaced traditional materials that were used previously (lime, gypsum and hydraulic limes). However, its use was not extended in time, and soon it was replaced by the use of artificial Portland cements. During 20th century this building material disappeared from use. What remains is it’s memory, in thousands and thousands of “stone witnesses” in our cities. Final properties of the cement largely depend on raw materials used and its combustion temperature. However, it was characterised by an easily implementation on facade masonry, fast-setting (about 15 minutes), good resistance , an agreeable structural consistency and colour.This article aims to show first steps, evolution and decay of Natural Cement Industry in Spain and its application in Madrid.

The late Miocene macroflora of the La Cerdaña Basin, Eastern Pirenees, Spain. Towards a Synthesis

The fossil plant-bearing beds of the Tortonian (late Miocene) intramontane basin of La Cerdanya (Eastern Pyrenees, Catalonia, Spain) have been investigated for more than a century, and 165 species from 12 outcrops have been described in previous publications. The sediments with rich plant fossil assemblages, which correspond to lacustrine diatomitic deposits, contain large numbers of plant remains, mainly leaf compressions and impressions. These assemblages are well preserved, a consequence of the rapid accumulation of plant remains in the sediments of the basin's ancient lake, and the often close proximity of its shores to wetland and upland vegetation. This paper provides a comprehensive taxonomic and nomenclatural review of the historic and new collections of late Miocene macroflora for the La Cerdanya Basin. Examination of the newer materials allowed emendments to be made to the diagnoses ofAbies saportana, Acer pyrenakum,Alnus occidentalis, Quercus hispanka and Tilia vidali provided by REROLLE for the basin at the end of the 19th century. In addition, 24 species of vascular plants are identified for the basin for the first time, including one horsetail, three conifers, 19 arboreal or bushy dicotyledonous angiosperms, and one monocotyledonous angiosperm. Indeed, this is the first time that Cedrela helkonia (UNGER) KNOBLOCH, Decodon sp„ Hedera cf multinervis KOLAKOVSKII, Mahonia cf pseudosimplex KVACEK & WALTHER, Smilax cf. aspera L. vm.fossilis and Ulmus cf. plurinervia UNGER have been recorded anywhere in the Iberian Peninsula. The La Cerdanya Basin plant assemblages of the late Miocene mainly consisted of conifers and deciduous broadleaved taxa of Arctotertiary origin; evergreen Palaeotropical elements were less well represented. This flora is similar to those recorded at coeval sites in northern Greece, northern Italy and central and eastern France. Within the Iberian Peninsula, the late Miocene macroflora reported for the nearby Seu d'Urgell Basin is the most similar.

Interconexión monolítica de módulos fotovoltaicos de silicio amorfo en lámina delgada sobre vidrio mediante ablación láser en régimen de nanosegundos

Esta tesis se centra en el estudio de una secuencia de procesos basados en la tecnología láser y ejecutados en dispositivos fotovoltaicos, que son imprescindibles para el desarrollo en general de las tecnologías fotovoltaicas basadas en lámina delgada y, en particular, de aquellas que utilizan silicio amorfo como absorbente, así como en aplicaciones posteriores de estas tecnologías de alto valor añadido como es la integración arquitectónica de este tipo de dispositivos. En gran parte de las tecnologías FV de lámina delgada, y muy particularmente en la de silicio amorfo, el material se deposita sobre un substrato en un área lo suficientemente grande para que se requiera de un proceso de subdivisión del dispositivo en células de tamaño adecuado, y su posterior conexión en serie para garantizar las figuras eléctricas nominales del dispositivo. Este proceso se ha desarrollado industrialmente hace años, pero no ha habido un esfuerzo científico asociado que permitiera conocer en profundidad los efectos que los procesos en si mismos tiene de forma individualizada sobre los materiales que componen el dispositivo y sus características finales. Este trabajo, desarrollado durante años en el Centro Láser de la UPM, en estrecha colaboración con Centro de Investigaciones Energéticas y Medioambientales (CIEMAT), la Universidad de Barcelona (UB), y la Universidad Politécnica de Cataluña (UPC), se centra justamente en un estudio detallado de dichos procesos, denominados habitualmente P1, P2, P3 y P4 atendiendo al orden en el que se realizan en el dispositivo. Este estudio incluye tanto la parametrización de los procesos, el análisis del efecto que los mismos producen sobre los materiales que componen el dispositivo y su comportamiento fotoeléctrico final, así como la evaluación del potencial uso de fuentes láser de última generación (ultrarrápidas) frente al estándar industrial en la actualidad que es el empleo de fuentes láser convencionales de ancho temporal en el rango de los nanosegundos. En concreto se ha estudiado en detalle las ventajas y limitaciones del uso de sistemas con diferentes rangos espectrales (IR, VIS y UV) y temporales (nanosegundos y picosegundos) para diferentes tipos de configuraciones y disposiciones tecnológicas (entendiendo por estas las habituales configuraciones en substrato y superestrato de este tipo de dispositivos). La caracterización individual de los procesos fue realizada primeramente en células de laboratorio específicamente diseñadas, abriendo nuevos planteamientos y conceptos originales para la mejora de los procesos láser de interconexión y posibilitando el empleo y desarrollo de técnicas y métodos avanzados de caracterización para el estudio de los procesos de ablación en las distintas láminas que conforman la estructura de los dispositivos fotovoltaicos, por lo que se considera que este trabajo ha propuesto una metodología completamente original, y que se ha demostrado efectiva, en este ámbito. Por último el trabajo aborda un tema de particular interés, como es el posible uso de los procesos desarrollados, no para construir los módulos fotovoltaicos en sí, sino para personalizarlos en forma y efectos visuales para potenciar su uso mediante elementos integrables arquitectónicamente, lo que es un ámbito de gran potencial de desarrollo futuro de las tecnologías fotovoltaicas de lámina delgada. En concreto se presentan estudios de fabricación de dispositivos integrables arquitectónicamente y plenamente funcionales no solo en dispositivos de silicio amorfo con efectos de transparencias y generación de formas libres, si no que también se incluye la posibilidad de hacer tales dispositivos con células de silicio cristalino estándar que es la tecnología fotovoltaica de mayor presencia en mercado. Es importante, además, resaltar que la realización de este trabajo ha sido posible gracias a la financiación obtenida con dos proyectos de investigación aplicada, MICROSIL (PSE-120000-2008-1) e INNDISOL (IPT-420000-2019-6), y los correspondientes al Plan Nacional de I+D+I financiados por el ministerio de Ciencia e Innovación y el Ministerio de Economía y Competitividad: CLÁSICO (ENE 2007- 67742-C04-04) y AMIC ENE2010-21384-C04-02. De hecho, y en el marco de estos proyectos, los resultados de este trabajo han ayudado a conseguir algunos de los hitos más importantes de la tecnología fotovoltaica en nuestro país en los últimos años, como fue en el marco de MICROSIL la fabricación del primer módulo de silicio amorfo con tecnología íntegramente española (hecho en colaboración con el CIEMAT), o la fabricación de los dispositivos para integración arquitectónica con geometrías libres que se describen en esta Tesis y que fueron parte de los desarrollos del proyecto INNDISOL. ABSTRACT This thesis focuses on the study of a sequence of laser-based technology and processes executed in photovoltaic devices, which are essential for the overall development of photovoltaic technologies based on thin film and, in particular, those using amorphous silicon as absorbent and subsequent applications of these technologies with high added value such as the architectural integration of such devices. In much of the PV thin film technologies, and particularly in the amorphous silicon material is deposited on a substrate in an area large enough so that it requires a process of subdivision of the device in cells of appropriate size, and subsequent serial connection to ensure nominal device power figures. This process has been industrially developed years ago, but there has been an associate scientific effort that would learn more about the effects that the processes themselves have either individually on the materials that make up the device and its final characteristics. This work, developed over years in the Laser Center of the UPM, in close collaboration with Centre for Energy and Environmental Research (CIEMAT), the University of Barcelona (UB) and the Polytechnic University of Catalonia (UPC)., Focuses precisely in a detailed study of these processes, usually they called P1, P2, P3 and P4 according to the order in which they perform on the device. This study includes both the parameters of the processes, the analysis of the effect they produce on the materials making up the device and its final photoelectric behavior as well as the potential use of EVALUATION of next-generation laser sources (ultrafast) versus standard industry today is the use of conventional laser sources temporal width in the range of nanoseconds. In particular we have studied in detail the advantages and limitations of using systems with different spectral ranges (IR, UV and VIS) and time (nanosecond and picosecond) for different configurations and technological provisions (meaning these typical configurations in substrate and superstrate such devices). Individual characterization of the processes was conducted primarily in laboratory cells specifically designed, opening new approaches and original concepts for improving laser interconnection processes and enabling the use and development of advanced techniques and characterization methods for studying the processes ablation in the different sheets making up the structure of the photovoltaic devices, so it is considered that this work has proposed a completely original methodology, which has proven effective in this area. Finally, the paper addresses a topic of particular interest, as is the possible use of lso developed processes, not to build the photovoltaic modules themselves but to customize fit and visual effects to enhance their use by integrated architectural elements, which is an area of great potential for future development of thin film photovoltaic technologies. Specifically studies manufacture of integrated architecturally and fully functional not only in amorphous silicon devices with transparency effects and generating freeform devices occur, if not also include the ability to make such devices with cells of standard crystalline silicon photovoltaic technology is more visible in the market. It is also important to note that the completion of this work has been possible thanks to the financing obtained with two applied research projects, Microsil (PSE-120000- 2008-1) and INNDISOL (IPT-420000-2019-6), and those for the National R & D funded by the Ministry of Science and Innovation and the Ministry of Economy and Competitiveness: CLASSIC (ENE 2007-67742-C04-04) and AMIC ENE2010-21384-C04- 02. In fact, within the framework of these projects, the results of this work have helped get some of the most important milestones of photovoltaic technology in our country in recent years, as it was under Microsil making the first module Amorphous silicon technology with entirely Spanish (made in collaboration with CIEMAT), or the manufacture of devices for architectural integration with free geometries that are described in this thesis and that were part of the project Inndisol developments.

Determination of selected pharmaceutical compounds in biosolids bysupported liquid extraction and gas chromatography?tandem massspectrometry

In this work, an analytical method was developed for the determination of pharmaceutical drugs inbiosolids. Samples were extracted with an acidic mixture of water and acetone (1:2, v/v) and supportedliquid extraction was used for the clean-up of extracts, eluting with ethyl acetate:methanol (90:10, v/v).The compounds were determined by gas chromatography?tandem mass spectrometry using matrix-match calibration after silylation to form their t-butyldimethylsilyl derivatives. This method presentsvarious advantages, such as a fairly simple operation for the analysis of complex matrices, the use ofinexpensive glassware and low solvent volumes. Satisfactory mean recoveries were obtained with thedeveloped method ranging from 70 to 120% with relative standard deviations (RSDs) ? 13%, and limitsof detection between 0.5 and 3.6 ng g?1. The method was then successfully applied to biosolids samplescollected in Madrid and Catalonia (Spain). Eleven of the sixteen target compounds were detected in thestudied samples, at levels up to 1.1 ?g g?1(salicylic acid). Ibuprofen, caffeine, paracetamol and fenofibratewere detected in all of the samples analyzed.