The lead salt quantum dot intermediate band solar cell

We propose a new kind of quantum dot (QD) materials for the implementation of the intermediate band solar cell (IBSC) [1]. The materials are formed by lead salt QDs of the family IV-VI (PbTe, PbSe or PbS) embedded in a semiconductor of the family II-VI (Cd1-xMgxTe, CdxZn1-xTe, and CdS1-xSex or ZnSe1-xTex, respectively). These QDs are not nucleated due to lattice mismatch, as it is the case of the InAs/GaAs QD material system grown by the Stranski-Krastanov (S-K) mode. In these materials, the QDs precipitate due to the difference in lattice type: the QD lead salt material crystallizes in the rocksalt structure, while the II-VI host material has the zincblende structure [2]. Therefore, it is possible to use lattice-matched QD/host combinations, avoiding all the strain-related problems found in previous QD-IBSC developments. In this paper we discuss the properties of the lead salt QD materials and propose that they are appropriate to overcome the fundamental drawbacks of present III-V-based QD-IBSC prototypes. We also calculate the band diagram for some examples of IV-VI/II-VI QD materials. The detailed balance efficiency limit of QD-IBSCs based on the studied materials is found to be over 60% under maximum concentration.

Isotopic prediction calculation methodologies: application to Vandellos-II Reactor cycles 7-11

Determining as accurate as possible spent nuclear fuel isotopic content is gaining importance due to its safety and economic implications. Since nowadays higher burn ups are achievable through increasing initial enrichments, more efficient burn up strategies within the reactor cores and the extension of the irradiation periods, establishing and improving computation methodologies is mandatory in order to carry out reliable criticality and isotopic prediction calculations. Several codes (WIMSD5, SERPENT 1.1.7, SCALE 6.0, MONTEBURNS 2.0 and MCNP-ACAB) and methodologies are tested here and compared to consolidated benchmarks (OECD/NEA pin cell moderated with light water) with the purpose of validating them and reviewing the state of the isotopic prediction capabilities. These preliminary comparisons will suggest what can be generally expected of these codes when applied to real problems. In the present paper, SCALE 6.0 and MONTEBURNS 2.0 are used to model the same reported geometries, material compositions and burn up history of the Spanish Van de llós II reactor cycles 7-11 and to reproduce measured isotopies after irradiation and decay times. We analyze comparisons between measurements and each code results for several grades of geometrical modelization detail, using different libraries and cross-section treatment methodologies. The power and flux normalization method implemented in MONTEBURNS 2.0 is discussed and a new normalization strategy is developed to deal with the selected and similar problems, further options are included to reproduce temperature distributions of the materials within the fuel assemblies and it is introduced a new code to automate series of simulations and manage material information between them. In order to have a realistic confidence level in the prediction of spent fuel isotopic content, we have estimated uncertainties using our MCNP-ACAB system. This depletion code, which combines the neutron transport code MCNP and the inventory code ACAB, propagates the uncertainties in the nuclide inventory assessing the potential impact of uncertainties in the basic nuclear data: cross-section, decay data and fission yields

Fabrication of sub-100 nm IDT SAW devices on insulating, semiconducting and conductive substrates

This work describes the electron-beam (e-beam) lithography process developed to manufacture nano interdigital transducers (IDTs) to be used in high frequency (GHz) surface acoustic wave (SAW) applications. The combination of electron-beam (e-beam) lithography and lift-off process is shown to be effective in fabricating well-defined IDT finger patterns with a line width below 100 nm with a good yield. Working with insulating piezoelectric substrates brings about e-beam deflection. It is also shown how a very thin organic anti-static layer works well in avoiding this charge accumulation during e-beam lithography on the resist layer. However, the use of this anti-static layer is not required with the insulating piezoelectric layer laying on a semiconducting substrate such as highly doped silicon. The effect of the e-beam dose on a number of different layers (of insulating, insulating on semiconducting, semiconducting, and conductive natures) is provided. Among other advantages, the use of reduced e-beam doses increases the manufacturing time. The principal aim of this work is to explain the interrelation among e-beam dose, substrate nature and IDT structure. An extensive study of the e-beam lithography of long IDT-fingers is provided, in a wide variety of electrode widths, electrode numbers and electrode pitches. It is worthy to highlight that this work shows the influence of the e-beam dose on five substrates of different conductive nature

Comportamiento estructural de elementos de fábrica reforzados con materiales compuestos avanzados solicitados a flexión y flexocompresión

El refuerzo de estructuras existentes mediante el encolado exterior de láminas de polímeros reforzados con fibras (FRP) se ha convertido en la aplicación más común de los materiales compuestos avanzados en construcción. Estos materiales presentan muchas ventajas frente a los materiales convencionales (sin corrosión, ligeros, de fácil aplicación, etc.). Pero a pesar de las numerosas investigaciones realizadas, aún persisten ciertas dudas sobre algunos aspectos de su comportamiento y las aplicaciones prácticas se llevan a cabo sólo con la ayuda de guías, sin que haya una normativa oficial. El objetivo de este trabajo es incrementar el conocimiento sobre esta técnica de refuerzo, y más concretamente, sobre el refuerzo a flexión de estructuras de fábrica. Con frecuencia el elemento reforzado es de hormigón armado y las láminas de FRP encoladas al exterior sirven para mejorar su resistencia a flexión, cortante o compresión (encamisados). Sin embargo su empleo en otros materiales como las estructuras de fábrica resulta muy prometedor. Las fábricas se caracterizan por soportar muy bien los esfuerzos de compresión pero bastante mal los de tracción. Adherir láminas de materiales compuestos puede servir para mejorar la capacidad resistente de elementos de fábrica sometidos a esfuerzos de flexión. Pero para ello, debe quedar garantizada una correcta adherencia entre el FRP y la fábrica, especialmente en edificios antiguos cuya superficie puede estar deteriorada por encontrarse a la intemperie o por el propio paso del tiempo. En el capítulo II se describen los objetivos fundamentales del trabajo y el método seguido. En el capítulo III se hace una amplia revisión del estado de conocimiento sobre el tema. En el apartado III.1 se detallan las principales características y propiedades mecánicas de fibras, matrices y materiales compuestos así como sus principales aplicaciones, haciendo especial hincapié en aspectos relativos a su durabilidad. En el apartado III.2 se incluye una revisión histórica de las líneas de investigación, tanto teóricas como empíricas, publicadas sobre estructuras de hormigón reforzadas a flexión encolando materiales compuestos. El apartado III.3 se centra en el aspecto fundamental de la adherencia refuerzo-soporte. Se hace un repaso a distintos modelos propuestos para prevenir el despegue distinguiendo si éste se inicia en la zona de anclaje o si está inducido por fisuras en la zona interior del elemento. Se observa falta de consenso en las propuestas. Además en este punto se relatan las campañas experimentales publicadas acerca de la adherencia entre materiales compuestos y fábricas. En el apartado III.4 se analizan las particularidades de las estructuras de fábrica. Además, se revisan algunas de las investigaciones relativas a la mejora de su comportamiento a flexión mediante láminas de FRP. El comportamiento mecánico de muros reforzados solicitados a flexión pura (sin compresión) ha sido documentado por varios autores, si bien es una situación poco frecuente en fábricas reales. Ni el comportamiento mecánico de muros reforzados solicitados a flexocompresión ni la incidencia que el nivel de compresión soportado por la fábrica tiene sobre la capacidad resistente del elemento reforzado han sido suficientemente tratados. En cuanto a los trabajos teóricos, las diferentes propuestas se basan en los métodos utilizados para hormigón armado y comparten los principios habituales de cálculo. Sin embargo, presentan diferencias relativas, sobre todo, a tres aspectos: 1) la forma de modelar el comportamiento de la fábrica, 2) el valor de deformación de cálculo del refuerzo, y 3) el modo de fallo que se considera recomendable buscar con el diseño. A pesar de ello, el ajuste con la parte experimental de cada trabajo suele ser bueno debido a una enorme disparidad en las variables consideradas. Cada campaña presenta un modo de fallo característico y la formulación que se propone resulta apropiada para él. Parece necesario desarrollar un método de cálculo para fábricas flexocomprimidas reforzadas con FRP que pueda ser utilizado para todos los posibles fallos, tanto atribuibles a la lámina como a la fábrica. En el apartado III.4 se repasan algunas lesiones habituales en fábricas solicitadas a flexión y se recogen ejemplos de refuerzos con FRP para reparar o prevenir estos daños. Para mejorar el conocimiento sobre el tema, se llevan a cabo dos pequeñas campañas experimentales realizadas en el Instituto de Ciencias de la Construcción Eduardo Torroja. La primera acerca de la adherencia de materiales compuestos encolados a fábricas deterioradas (apartado IV.1) y la segunda sobre el comportamiento estructural a flexocompresión de probetas de fábrica reforzadas con estos materiales (apartado IV.2). En el capítulo V se analizan algunos de los modelos de adherencia propuestos para prevenir el despegue del extremo del refuerzo. Se confirma que las predicciones obtenidas con ellos resultan muy dispares. Se recopila una base de datos con los resultados experimentales de campañas sobre adherencia de FRP a fábricas extraídas de la literatura y de los resultados propios de la campaña descrita en el punto IV.1. Esta base de datos permite conocer cual de los métodos analizados resulta más adecuado para dimensionar el anclaje de láminas de FRP adheridas a fábricas. En el capítulo VI se propone un método para la comprobación en agotamiento de secciones de fábrica reforzadas con materiales compuestos sometidas a esfuerzos combinados de flexión y compresión. Está basado en el procedimiento de cálculo de la capacidad resistente de secciones de hormigón armado pero adaptado a las fábricas reforzadas. Para ello, se utiliza un diagrama de cálculo tensión deformación de la fábrica de tipo bilineal (acorde con el CTE DB SE-F) cuya simplicidad facilita el desarrollo de toda la formulación al tiempo que resulta adecuado para predecir la capacidad resistente a flexión tanto para fallos debidos al refuerzo como a la fábrica. Además se limita la deformación de cálculo del refuerzo teniendo en consideración ciertos aspectos que provocan que la lámina adherida no pueda desarrollar toda su resistencia, como el desprendimiento inducido por fisuras en el interior del elemento o el deterioro medioambiental. En concreto, se propone un “coeficiente reductor por adherencia” que se determina a partir de una base de datos con 68 resultados experimentales procedentes de publicaciones de varios autores y de los ensayos propios de la campaña descrita en el punto IV.2. También se revisa la formulación propuesta con ayuda de la base de datos. En el capítulo VII se estudia la incidencia de las principales variables, como el axil, la deformación de cálculo del refuerzo o su rigidez, en la capacidad final del elemento. Las conclusiones del trabajo realizado y las posibles líneas futuras de investigación se exponen en el capítulo VIII. ABSTRACT Strengthening of existing structures with externally bonded fiber reinforced polymers (FRP) has become the most common application of advanced composite materials in construction. These materials exhibit many advantages in comparison with traditional ones (corrosion resistance, light weight, easy to apply, etc.). But despite countless researches have been done, there are still doubts about some aspects of their behaviour and applications are carried out only with the help of guidelines, without official regulations. The aim of this work is to improve the knowledge on this retrofitting technique, particularly in regard to flexural strengthening of masonry structures. Reinforced concrete is often the strengthened material and external glued FRP plates are used to improve its flexural, shear or compressive (by wrapping) capacity. However the use of this technique on other materials like masonry structures looks promising. Unreinforced masonry is characterized for being a good material to support compressive stresses but really bad to withstand tensile ones. Glue composite plates can improve the flexural capacity of masonry elements subject to bending. But a proper bond between FRP sheet and masonry must be ensured to do that, especially in old buildings whose surface can be damaged due to being outside or ageing. The main objectives of the work and the methodology carried out are described In Chapter II. An extensive overview of the state of art is done in Chapter III. In Section III.1 physical and mechanical properties of fibers, matrix and composites and their main applications are related. Durability aspects are especially emphasized. Section III.2 includes an historical overview of theoretical and empirical researches on concrete structures strengthened gluing FRP plates to improve their flexural behaviour. Section III.3 focuses on the critical point of bonding between FRP and substrate. Some theoretical models to prevent debonding of FRP laminate are reviewed, it has made a distinction between models for detachment at the end of the plate or debonding in the intermediate zones due to the effects of cracks. It is observed a lack of agreement in the proposals. Some experimental studies on bonding between masonry and FRP are also related in this chapter. The particular characteristics of masonry structures are analyzed in Section III.4. Besides some empirical and theoretical investigations relative to improve their flexural capacity with FRP sheets are reviewed. The mechanical behaviour of strengthened walls subject to pure bending (without compression) has been established by several authors, but this is an unusual situation for real masonry. Neither mechanical behaviour of walls subject to bending and compression nor influence of axial load in the final capacity of the strengthened element are adequately studied. In regard to theoretical studies, the different proposals are based on reinforced concrete analytical methods and share common design principles. However, they present differences, especially, about three aspects: 1) the constitutive law of masonry, 2) the value of ultimate FRP strain and 3) the desirable failure mode that must be looked for. In spite of them, a good agreement between each experimental program and its theoretical study is often exhibited due to enormous disparity in considered test parameters. Each experimental program usually presents a characteristic failure mode and the proposed formulation results appropriate for this one. It seems necessary to develop a method for FRP strengthened walls subject to bending and compression enable for all failure modes (due to FRP or masonry). Some common damages in masonry subject to bending are explained in Section III.4. Examples of FRP strengthening to repair or prevent these damages are also written. Two small experimental programs are carried out in Eduardo Torroja Institute to improve the knowledge on this topic. The first one is concerned about the bond between FRP plates and damaged masonry (section IV.1) and the second one is related to the mechanical behaviour of the strengthened masonry specimens subject to out of plane bending combined with axial force (section IV.2). In the Chapter V some bond models to prevent the debonding at the FRP plate end are checked. It is confirmed that their predictions are so different. A pure-shear test database is compiled with results from the existing literature and others from the experimental program described in section IV.1. This database lets know which of the considered model is more suitable to design anchorage lengths of glued FRP to masonry. In the Chapter VI a method to check unreinforced masonry sections with external FRP strengthening subject to bending and compression to the ultimate limit state is proposed. This method is based on concrete reinforced one, but it is adapted to strengthened masonry. A bilinear constitutive law is used for masonry (according to CTE DB SE-F). Its simplicity helps to develop the model formulation and it has proven to be suitable to predict bending capacity either for FRP failures or masonry crushing. With regard to FRP, the design strain is limited. It is taken into account different aspects which cause the plate can’t reach its ultimate strength, like intermediate FRP debonding induced by opening cracking or environmental damage. A “bond factor” is proposed. It is obtained by means of an experimental bending test database that includes 68 results from the existing literature and from the experimental program described in section IV.2. The proposed formulation has also been checked with the help of bending database. The effects of the main parameters, like axial load, FRP design effective strain or FRP stiffness, on the bending capacity of the strengthened element are studied in Chapter VII. Finally, the main conclusions from the work carried out are summarized in Chapter VIII. Future lines of research to be explored are suggested as well.

Propellantless de orbiting of space debris by bare electrodynamic tethers

A 3-year Project started on November 1 2010, financed by the European Commision within the FP-7 Space Program, and aimed at developing an efficient de-orbit system that could be carried on board by future spacecraft launched into LEO, will be presented. The operational system will deploy a thin uninsulated tape-tether to collect electrons as a giant Langmuir probe, using no propellant/no power supply, and generating power on board. This project will involve free-fall tests, and laboratory hypervelocity-impact and tether-current tests, and design/Manufacturing of subsystems: interface elements, electric control and driving module, electron-ejecting plasma contactor, tether-deployment mechanism/end-mass, and tape samples. Preliminary results to be presented involve: i) devising criteria for sizing the three disparate tape dimensions, affecting mass, resistance, current-collection, magnetic self-field, and survivability against debris itself; ii) assessing the dynamical relevance of tether parameters in implementing control laws to limit oscillations in /off the orbital plane, where passive stability may be marginal; iii) deriving a law for bare-tape current from numerical simulations and chamber tests, taking into account ambient magnetic field, ion ram motion, and adiabatic electron trapping; iv) determining requirements on a year-dormant hollow cathode under long times/broad emission-range operation, and trading-off against use of electron thermal emission; v) determining requirements on magnetic components and power semiconductors for a control module that faces high voltage/power operation under mass/volume limitations; vi) assessing strategies to passively deploy a wide conductive tape that needs no retrieval, while avoiding jamming and ending at minimum libration; vii) evaluating the tape structure as regards conductive and dielectric materials, both lengthwise and in its cross-section, in particular to prevent arcing in triple-point junctions.

Nuevos datos documentales sobre la construcción de la mezquita de Córdoba en el reinado de Abd Al-Rahman II

Nuevos datos documentales sobre la construcción de la mezquita de Córdoba en el reinado de Abd Al-Rahman II

Technical evolution of 3d modular construction from the nineteenth century to world war II

3D Modular construction is poorly known and scarcely published in technical literature. In spite of that there are an increasing number of manufacturers offering their products in different countries. This method has largely evolved from early examples such as the American Gold Rush prefabrication in the nineteenth century, the Sears precut homes or Voisin´s prototypes for modular homes, to the end of the first half of the twentieth century. In this period a non negligible number of attempts in 3D modular construction have been carried out, ranging from theoretical proposals to several hundred or thousand units produced. Selected examples of modular architecture will be analyses in order to illustrate its technical evolution, concerning materials, structure, transportation and on site assembly. Success and failure factors of the different systems will be discussed. Conclusions about building criteria shown in them and their applicability in current architecture will be drawn.

Estudio de los materiales que componen el sistema constructivo de las viviendas del casco histórico de Maracaibo (Venezuela)

En este trabajo de investigación que se presenta para optar al grado de Doctor, se analizan y estudian los materiales que conforman las viviendas de mampostería de arenisca “Piedra de Ojo” del casco histórico de Maracaibo, Venezuela, construidas en el siglo XIX. No existe una bibliografía descriptiva técnico-constructiva del sistema constructivo, por lo que esta tesis complementa la escasa descripción estilística existente donde apenas se mencionan algunos materiales de construcción. Definido el marco histórico y las manzanas del área en donde se encontraban las viviendas preseleccionadas a estudiar, en la visita de campo se seleccionaron 12 que se encontraban en estado de deterioro, y que permitieron recolectar las muestras más fácilmente. Para realizar la caracterización y comportamientos de los diferentes materiales utilizados: piedra y morteros en los cerramientos, maderas en armaduras de tejados, techos y carpintería de puertas y ventanas, cerámicos en muros y acabados, etc. Para complementar lo antes dicho se ha dividido esta tesis en seis capítulos: En el capítulo I se desarrolla el estado del arte a nivel nacional e internacional de trabajos de investigación, similares. Se aborda la memoria histórica, que es una reseña de la evolución de la vivienda en la ciudad de Maracaibo. En el capítulo II se describe la metodología empleada en la tesis, de acuerdo a los objetivos, tanto generales como específicos de la investigación. Que ha cubierto diferentes frentes: consulta bibliográfica, levantamiento planimétrico, toma de muestras, análisis de visu, caracterización físico-química y correlación de resultados. Se ha desarrollado el trabajo tanto in situ como en laboratorio y despacho. El capítulo III presenta la caracterización de la arenisca “Piedra de Ojo”, se desarrolla: la descripción geológica y caracterización petrológica. Se reseñan los ensayos realizados en laboratorio como: caracterización de visu, caracterización petrográfica, estudio petrográfico por microcopia óptica de trasmisión, estudio petrográfico por microcopia electrónica de barrido, microscopia electrónica de barrido en modo electrones secundarios (SSE) y microscopia electrónica de barrido en modo electrones retrodispersados. También las propiedades escalares de los mampuestos y los siguientes valores: densidades, porosidades y resistencia mecánicas, entre otros. En el capítulo IV se analizan las características de los morteros aplicados en las viviendas, y la patología o lesiones que presentan. Se clasifican en tres tipos: mortero de junta o asiento, de enfoscado y revoco. Se documenta la realización de los ensayos físicos y químicos, resistencia mecánica y de granulometría; se explican sus componentes principales: conglomerante de cal, áridos y aditivos y la tecnología de fabricación, así como las características físicas, hídricas, químicas y granulométricas. El capítulo V, contiene las aplicaciones constructivas de los materiales de albañilería, Se describen otros elementos de la vivienda como; cimentaciones, muros mixtos, molduras, apliques y pinturas y finalmente pavimentos. Y en el capítulo VI se analizan las especies de madera más representativas usadas en las armaduras de las cubiertas, así como los elementos de cubrición. De igual forma se describe la carpintería de puertas y ventanas, así como sus dinteles o cargaderos de madera y se realiza la identificación anatómica, las propiedades físicas y mecánicas de las utilizadas. Entre los resultados y conclusiones se determinó que el 90% de los materiales utilizados en su construcción proceden de zonas cercanas a la construcción de la vivienda, como la formación El Milagro convertida en cantera de piedra y que el resto de los materiales provenían de la Isla de Toas y de la exportación de las islas del Caribe y de Europa como el cemento. El principal aporte de esta investigación es el análisis técnico constructivo y la caracterización física, mecánica y química de los materiales de la vivienda, con el fin de que dicha información sea usada para definir los materiales nuevos a utilizar en las restauraciones de las viviendas y en futuras líneas de investigación. ABSTRACT In this research paper submitted to opt to the degree of Doctor, the materials that make the “Piedra de Ojo” sandstone masonry houses of the historical center of Maracaibo, Venezuela, built in the XIX century, are analyzed and studied. There exists no technical-constructive descriptive literature of the constructive system, so this thesis complements the very limited existing stylistic description, where barely some construction materials are mentioned. With the historical context and the blocks of the area where the preselected houses to be studied being defined, 12 of these houses that were in a state of decay (deterioration) were selected and this condition allowed to collect samples more easily, in order to carry out the characterization and behavior of the different materials used: stone and mortars in the walls, wood trusses in roofs, ceilings and woodwork of doors and windows, walls and ceramic finishes, etc. To complement the foregoing, this thesis has been divided in six chapters: In Chapter I, the state of art at national and international levels of similar research is developed, which is a review of the evolution of housing in the city of Maracaibo. In Chapter II, the methodology used in the thesis is described, according to the research’s objectives, general and specific ones, which have covered several fronts: literature survey, planimetric survey, sampling, visu analysis, physical-chemical characterization and correlation of results. Chapter III presents the characterization of the “Piedra de Ojo” sandstone; geological description and petrologic characterization are developed. Essays performed in the laboratory are reviewed, such as: visu characterization, petrographic characaterization, petrographic study by optical microscopy of transmission, petrographic study by electronic scanning microscopy in secondary electron mode (SSE) and electron microscopy scaning by backscattered electron mode. Also scalar properties of the masonry and the following: density, porosity and mechanical resistance, among others. In Chapter IV, characteristics of the mortars used in the houses are analyzed and pathology or damages are presented. They are classified into three types: grout, cement render and plaster. Physical and chemical testing, mechanical strength and grain size (granulometric) is documented; its main components are explained: lime binder, aggregates and additives and manufacturing technology as well as the physical, water, chemical and granulometric characteristics. Chapter V contains the constructive applications of masonry materials. Other housing elements are described, such as; foundations, mixed walls, moldings, wall paintings and finally floorings (pavements). And in chapter VI the most representative species of wood used in the overhead fixtures and cover elements are analyzed. Likewise, woodwork of doors and windows and their wooden lintels or landings are described; anatomical identification and physical and mechanical properties of the ones used is made. The results and conclusions determined that 90% of the materials used in its construction came from areas near the construction of housing, such as El Milagro formation, converted into stone quarry and other materials came from the Toas Island and from the export of the Caribbean islands and Europe, such as cement. The main contribution of this research is the constructive technical analysis and physical, mechanical and chemical characterization of the materials of the houses, in order that such information is used to define the new materials to be used in the housing restoration and future research lines.