A Light-Weight On-Chip Monitoring Network for Dynamic Adaptation and Calibration

Current nanometer technologies suffer within-die parameter uncertainties, varying workload conditions, aging, and temperature effects that cause a serious reduction on yield and performance. In this scenario, monitoring, calibration, and dynamic adaptation become essential, demanding systems with a collection of multi purpose monitors and exposing the need for light-weight monitoring networks. This paper presents a new monitoring network paradigm able to perform an early prioritization of the information. This is achieved by the introduction of a new hierarchy level, the threshing level. Targeting it, we propose a time-domain signaling scheme over a single-wire that minimizes the network switching activity as well as the routing requirements. To validate our approach, we make a thorough analysis of the architectural trade-offs and expose two complete monitoring systems that suppose an area improvement of 40% and a power reduction of three orders of magnitude compared to previous works.

A Monitoring Infrastructure for FPGA Self-Awareness and Dynamic Adaptation

Variabilities associated with CMOS evolution affect the yield and performance of current digital designs. FPGAs, which are widely used for fast prototyping and implementation of digital circuits, also suffer from these issues. Proactive approaches start to appear to achieve self-awareness and dynamic adaptation of these devices. To support these techniques we propose the employment of a multi-purpose sensor network. This infrastructure, through adequate use of configuration and automation tools, is able to obtain relevant data along the life cycle of an FPGA. This is realised at a very reduced cost, not only in terms of area or other limited resources, but also regarding the design effort required to define and deploy the measuring infrastructure. Our proposal has been validated by measuring inter-die and intra-die variability in different FPGA families.

Core physics and safety analysis of Generation-IV Sodium Fast Reactors using existing and newly developed computational tools

El futuro de la energía nuclear de fisión dependerá, entre otros factores, de la capacidad que las nuevas tecnologías demuestren para solventar los principales retos a largo plazo que se plantean. Los principales retos se pueden resumir en los siguientes aspectos: la capacidad de proporcionar una solución final, segura y fiable a los residuos radiactivos; así como dar solución a la limitación de recursos naturales necesarios para alimentar los reactores nucleares; y por último, una mejora robusta en la seguridad de las centrales que en definitiva evite cualquier daño potencial tanto en la población como en el medio ambiente como consecuencia de cualquier escenario imaginable o más allá de lo imaginable. Siguiendo estas motivaciones, la Generación IV de reactores nucleares surge con el compromiso de proporcionar electricidad de forma sostenible, segura, económica y evitando la proliferación de material fisible. Entre los sistemas conceptuales que se consideran para la Gen IV, los reactores rápidos destacan por su capacidad potencial de transmutar actínidos a la vez que permiten una utilización óptima de los recursos naturales. Entre los refrigerantes que se plantean, el sodio parece una de las soluciones más prometedoras. Como consecuencia, esta tesis surgió dentro del marco del proyecto europeo CP-ESFR con el principal objetivo de evaluar la física de núcleo y seguridad de los reactores rápidos refrigerados por sodio, al tiempo que se desarrollaron herramientas apropiadas para dichos análisis. Efectivamente, en una primera parte de la tesis, se abarca el estudio de la física del núcleo de un reactor rápido representativo, incluyendo el análisis detallado de la capacidad de transmutar actínidos minoritarios. Como resultado de dichos análisis, se publicó un artículo en la revista Annals of Nuclear Energy [96]. Por otra parte, a través de un análisis de un hipotético escenario nuclear español, se evalúo la disponibilidad de recursos naturales necesarios en el caso particular de España para alimentar una flota específica de reactores rápidos, siguiendo varios escenarios de demanda, y teniendo en cuenta la capacidad de reproducción de plutonio que tienen estos sistemas. Como resultado de este trabajo también surgió una publicación en otra revista científica de prestigio internacional como es Energy Conversion and Management [97]. Con objeto de realizar esos y otros análisis, se desarrollaron diversos modelos del núcleo del ESFR siguiendo varias configuraciones, y para diferentes códigos. Por otro lado, con objeto de poder realizar análisis de seguridad de reactores rápidos, son necesarias herramientas multidimensionales de alta fidelidad específicas para reactores rápidos. Dichas herramientas deben integrar fenómenos relacionados con la neutrónica y con la termo-hidráulica, entre otros, mediante una aproximación multi-física. Siguiendo este objetivo, se evalúo el código de difusión neutrónica ANDES para su aplicación a reactores rápidos. ANDES es un código de resolución nodal que se encuentra implementado dentro del sistema COBAYA3 y está basado en el método ACMFD. Por lo tanto, el método ACMFD fue sometido a una revisión en profundidad para evaluar su aptitud para la aplicación a reactores rápidos. Durante ese proceso, se identificaron determinadas limitaciones que se discutirán a lo largo de este trabajo, junto con los desarrollos que se han elaborado e implementado para la resolución de dichas dificultades. Por otra parte, se desarrolló satisfactoriamente el acomplamiento del código neutrónico ANDES con un código termo-hidráulico de subcanales llamado SUBCHANFLOW, desarrollado recientemente en el KIT. Como conclusión de esta parte, todos los desarrollos implementados son evaluados y verificados. En paralelo con esos desarrollos, se calcularon para el núcleo del ESFR las secciones eficaces en multigrupos homogeneizadas a nivel nodal, así como otros parámetros neutrónicos, mediante los códigos ERANOS, primero, y SERPENT, después. Dichos parámetros se utilizaron más adelante para realizar cálculos estacionarios con ANDES. Además, como consecuencia de la contribución de la UPM al paquete de seguridad del proyecto CP-ESFR, se calcularon mediante el código SERPENT los parámetros de cinética puntual que se necesitan introducir en los típicos códigos termo-hidráulicos de planta, para estudios de seguridad. En concreto, dichos parámetros sirvieron para el análisis del impacto que tienen los actínidos minoritarios en el comportamiento de transitorios. Concluyendo, la tesis presenta una aproximación sistemática y multidisciplinar aplicada al análisis de seguridad y comportamiento neutrónico de los reactores rápidos de sodio de la Gen-IV, usando herramientas de cálculo existentes y recién desarrolladas ad' hoc para tal aplicación. Se ha empleado una cantidad importante de tiempo en identificar limitaciones de los métodos nodales analíticos en su aplicación en multigrupos a reactores rápidos, y se proponen interesantes soluciones para abordarlas. ABSTRACT The future of nuclear reactors will depend, among other aspects, on the capability to solve the long-term challenges linked to this technology. These are the capability to provide a definite, safe and reliable solution to the nuclear wastes; the limitation of natural resources, needed to fuel the reactors; and last but not least, the improved safety, which would avoid any potential damage on the public and or environment as a consequence of any imaginable and beyond imaginable circumstance. Following these motivations, the IV Generation of nuclear reactors arises, with the aim to provide sustainable, safe, economic and proliferationresistant electricity. Among the systems considered for the Gen IV, fast reactors have a representative role thanks to their potential capacity to transmute actinides together with the optimal usage of natural resources, being the sodium fast reactors the most promising concept. As a consequence, this thesis was born in the framework of the CP-ESFR project with the generic aim of evaluating the core physics and safety of sodium fast reactors, as well as the development of the approppriated tools to perform such analyses. Indeed, in a first part of this thesis work, the main core physics of the representative sodium fast reactor are assessed, including a detailed analysis of the capability to transmute minor actinides. A part of the results obtained have been published in Annals of Nuclear Energy [96]. Moreover, by means of the analysis of a hypothetical Spanish nuclear scenario, the availability of natural resources required to deploy an specific fleet of fast reactor is assessed, taking into account the breeding properties of such systems. This work also led to a publication in Energy Conversion and Management [97]. In order to perform those and other analyses, several models of the ESFR core were created for different codes. On the other hand, in order to perform safety studies of sodium fast reactors, high fidelity multidimensional analysis tools for sodium fast reactors are required. Such tools should integrate neutronic and thermal-hydraulic phenomena in a multi-physics approach. Following this motivation, the neutron diffusion code ANDES is assessed for sodium fast reactor applications. ANDES is the nodal solver implemented inside the multigroup pin-by-pin diffusion COBAYA3 code, and is based on the analytical method ACMFD. Thus, the ACMFD was verified for SFR applications and while doing so, some limitations were encountered, which are discussed through this work. In order to solve those, some new developments are proposed and implemented in ANDES. Moreover, the code was satisfactorily coupled with the thermal-hydraulic code SUBCHANFLOW, recently developed at KIT. Finally, the different implementations are verified. In addition to those developments, the node homogenized multigroup cross sections and other neutron parameters were obtained for the ESFR core using ERANOS and SERPENT codes, and employed afterwards by ANDES to perform steady state calculations. Moreover, as a result of the UPM contribution to the safety package of the CP-ESFR project, the point kinetic parameters required by the typical plant thermal-hydraulic codes were computed for the ESFR core using SERPENT, which final aim was the assessment of the impact of minor actinides in transient behaviour. All in all, the thesis provides a systematic and multi-purpose approach applied to the assessment of safety and performance parameters of Generation-IV SFR, using existing and newly developed analytical tools. An important amount of time was employed in identifying the limitations that the analytical nodal diffusion methods present when applied to fast reactors following a multigroup approach, and interesting solutions are proposed in order to overcome them.

A self-timed multipurpose delay sensor for field programmable gate arrays (FPGAs)

This paper presents a novel self-timed multi-purpose sensor especially conceived for Field Programmable Gate Arrays (FPGAs). The aim of the sensor is to measure performance variations during the life-cycle of the device, such as process variability, critical path timing and temperature variations. The proposed topology, through the use of both combinational and sequential FPGA elements, amplifies the time of a signal traversing a delay chain to produce a pulse whose width is the sensor’s measurement. The sensor is fully self-timed, avoiding the need for clock distribution networks and eliminating the limitations imposed by the system clock. One single off- or on-chip time-to-digital converter is able to perform digitization of several sensors in a single operation. These features allow for a simplified approach for designers wanting to intertwine a multi-purpose sensor network with their application logic. Employed as a temperature sensor, it has been measured to have an error of ±0.67 °C, over the range of 20–100 °C, employing 20 logic elements with a 2-point calibration.

Engineering Computational Emotion - A Reference Model for Emotion in Artificial Systems

Emotion is generally argued to be an influence on the behavior of life systems, largely concerning flexibility and adaptivity. The way in which life systems acts in response to a particular situations of the environment, has revealed the decisive and crucial importance of this feature in the success of behaviors. And this source of inspiration has influenced the way of thinking artificial systems. During the last decades, artificial systems have undergone such an evolution that each day more are integrated in our daily life. They have become greater in complexity, and the subsequent effects are related to an increased demand of systems that ensure resilience, robustness, availability, security or safety among others. All of them questions that raise quite a fundamental challenges in control design. This thesis has been developed under the framework of the Autonomous System project, a.k.a the ASys-Project. Short-term objectives of immediate application are focused on to design improved systems, and the approaching of intelligence in control strategies. Besides this, long-term objectives underlying ASys-Project concentrate on high order capabilities such as cognition, awareness and autonomy. This thesis is placed within the general fields of Engineery and Emotion science, and provides a theoretical foundation for engineering and designing computational emotion for artificial systems. The starting question that has grounded this thesis aims the problem of emotion--based autonomy. And how to feedback systems with valuable meaning has conformed the general objective. Both the starting question and the general objective, have underlaid the study of emotion, the influence on systems behavior, the key foundations that justify this feature in life systems, how emotion is integrated within the normal operation, and how this entire problem of emotion can be explained in artificial systems. By assuming essential differences concerning structure, purpose and operation between life and artificial systems, the essential motivation has been the exploration of what emotion solves in nature to afterwards analyze analogies for man--made systems. This work provides a reference model in which a collection of entities, relationships, models, functions and informational artifacts, are all interacting to provide the system with non-explicit knowledge under the form of emotion-like relevances. This solution aims to provide a reference model under which to design solutions for emotional operation, but related to the real needs of artificial systems. The proposal consists of a multi-purpose architecture that implement two broad modules in order to attend: (a) the range of processes related to the environment affectation, and (b) the range or processes related to the emotion perception-like and the higher levels of reasoning. This has required an intense and critical analysis beyond the state of the art around the most relevant theories of emotion and technical systems, in order to obtain the required support for those foundations that sustain each model. The problem has been interpreted and is described on the basis of AGSys, an agent assumed with the minimum rationality as to provide the capability to perform emotional assessment. AGSys is a conceptualization of a Model-based Cognitive agent that embodies an inner agent ESys, the responsible of performing the emotional operation inside of AGSys. The solution consists of multiple computational modules working federated, and aimed at conforming a mutual feedback loop between AGSys and ESys. Throughout this solution, the environment and the effects that might influence over the system are described as different problems. While AGSys operates as a common system within the external environment, ESys is designed to operate within a conceptualized inner environment. And this inner environment is built on the basis of those relevances that might occur inside of AGSys in the interaction with the external environment. This allows for a high-quality separate reasoning concerning mission goals defined in AGSys, and emotional goals defined in ESys. This way, it is provided a possible path for high-level reasoning under the influence of goals congruence. High-level reasoning model uses knowledge about emotional goals stability, letting this way new directions in which mission goals might be assessed under the situational state of this stability. This high-level reasoning is grounded by the work of MEP, a model of emotion perception that is thought as an analogy of a well-known theory in emotion science. The work of this model is described under the operation of a recursive-like process labeled as R-Loop, together with a system of emotional goals that are assumed as individual agents. This way, AGSys integrates knowledge that concerns the relation between a perceived object, and the effect which this perception induces on the situational state of the emotional goals. This knowledge enables a high-order system of information that provides the sustain for a high-level reasoning. The extent to which this reasoning might be approached is just delineated and assumed as future work. This thesis has been studied beyond a long range of fields of knowledge. This knowledge can be structured into two main objectives: (a) the fields of psychology, cognitive science, neurology and biological sciences in order to obtain understanding concerning the problem of the emotional phenomena, and (b) a large amount of computer science branches such as Autonomic Computing (AC), Self-adaptive software, Self-X systems, Model Integrated Computing (MIC) or the paradigm of models@runtime among others, in order to obtain knowledge about tools for designing each part of the solution. The final approach has been mainly performed on the basis of the entire acquired knowledge, and described under the fields of Artificial Intelligence, Model-Based Systems (MBS), and additional mathematical formalizations to provide punctual understanding in those cases that it has been required. This approach describes a reference model to feedback systems with valuable meaning, allowing for reasoning with regard to (a) the relationship between the environment and the relevance of the effects on the system, and (b) dynamical evaluations concerning the inner situational state of the system as a result of those effects. And this reasoning provides a framework of distinguishable states of AGSys derived from its own circumstances, that can be assumed as artificial emotion.

Lo intermedio como lugar : lo intersticial, lo fronterizo y lo impreciso en la arquitectura contemporánea

1. Nuestra investigación se centra en el estudio de los “ámbitos o espacios intermedios” en momentos de la arquitectura contemporánea, en un período de transición entre finales de los años 80 y nuestros días. Pretendemos analizar cómo se presenta el ámbito intermedio en el objeto o lugar arquitectónico y su función o relación con el entorno cercano, desde el proyecto hasta su repercusión en la experiencia vivida. 2. El concepto de intermedio entendido como ámbito o espacio intersticial, fronterizo y ambivalente (o multivalente), atraviesa en la presente investigación el campo de la etimología, de la ciencia, del pensamiento y del arte, para detenerse en la arquitectura actual, llevándose a cabo una indagación concreta en el proceso de concepción, en la propuesta formal, espacial y funcional, así como en la percepción y demás experiencias o vivencias en el lugar arquitectónico. 3. En primer lugar nos proponemos estudiar y explorar el concepto de “intermedio” en sus características, funciones y ubicaciones dentro de la cultura contemporánea, detectando sus antecedentes culturales más importantes, para a continuación aplicarlo reflexivamente a obras significativas de arquitectura. La investigación se enfoca en la modalidad figural (imprecisa) de lo intermedio (en alusión al “figural” deleuziano), cuyas metáforas base son lo translúcido, la penumbra y la espuma, vinculadas al actual paradigma cultural de la complejidad (C. Jencks). A continuación se analizan las relaciones o implicaciones de dicha modalidad figural en obras de arquitectos como Eisenman, Holl, Tschumi, Ito, Fujimoto, Van Berkel y Bos, y Siza, comprobando su valor operativo y poniendo de manifiesto su sentido e importancia en la actualidad y en la disciplina. El estudio tiene como trasfondo el concepto de in-between de la obra de Eisenman, y utiliza conceptos de la filosofía del límite de Trías como algunos de sus principales fundamentos. 4. En cada una de las obras de arquitectura presentadas esta modalidad imprecisa se traduce en un ámbito o espacio intermedio figural específico. Son obras en las que real y virtual, matricial y objetual, arquitectura y territorio, existente y nuevo, colectivo e individual, social e íntimo, interior y exterior, y demás usos y funciones se entrelazan o funden. Son arquitecturas cuya geometría ya no se encuentra tan determinada por aspectos bi o tridimensionales del dibujo o de la construcción. A través de la manipulación de estas geometrías más o menos complejas, dinámicas e intersticiales, estas obras reflejan (o intuyen) las premisas del actual Zeitgeist: un cambio de esquemas de objetos a relaciones basado en un pensamiento más holístico, transdisciplinar, sistémico o complejo (E. Morin), y una nueva conciencia colectiva sobre la realidad que anuncia la crisis de la percepción, el cambio de paradigma y nuevos valores (F. Capra). Emerge otra forma de sentir y percibir el mundo, los lugares y los espacios, que poco a poco está cambiando el modo de pensar y dibujar la arquitectura, y consecuentemente de interaccionar con ella. 5. El sentido del espacio intermedio figural, emerge en las cada vez más complejas cualidades morfológico-espaciales y funcionales de una parte importante de la arquitectura actual. Arquitectura, geometría y tecnología informática están más entrelazadas que nunca, y de un modo más libre, para así poder indagar en nuevas formas de pensar y crear lugares en que los “espacios intermedios” que investigamos son un testimonio. El espacio arquitectónico se vuelve afectivo e interactivo, un lugar intermedio figural, formalizado por espacialidades intersticiales que parecen aludir a lo líquido, donde la forma es más matriz que configuración, el espacio más espacialidad que compartimiento, la función más versátil y multivalente que específica o autónoma, y la perplejidad, la imaginación y la evocación se entrecruzan y vuelven patentes. 6. La arquitectura de los lugares intermedios valora no solamente el “plano”, la “configuración” y la “transparencia”, sino sobre todo el “espacio” y la “relación” en sus interrelaciones con los usuarios y demás contextos. De la identidad a la relacionalidad, de la representación a la presentación, es una arquitectura que propone “otros espacios” que más que espacios son topografías y espacialidades intersticiales, de tensión, transición, transformación, relación, intercambio e interacción. Son lugares intermedios reales y virtuales, que se sirven tanto de la morfología como de la topología para conquistar nuevas espacialidades, pretendiendo salir de la estricta operación de “forming”/”morphing”/formación/”conformación” para explorar la de “spacing”/espaciamiento. Son lugares que se basan en conceptos como la zona de indiscernibilidad de Deleuze, la imagen- flujo de Buci-Glucksmann, la suspensión-entre de Sloterdijk, o el espacio no-objetivo al que se refiere José Gil, plasmándose en la arquitectura contemporánea como tropos de lo intersticial. 7. Son los lugares intermedios de la arquitectura actual, de espacialidad háptica, más “afectiva”, generativa e interactiva, donde ese ámbito intermedio transforma y es transformado, “afecta”, “con-mueve” (nos hace mover/accionar) y evoca otros lugares, otras posibilidades de espacio habitable u ocupable. Emerge lo intermedio como lugar, algo que anuncia y exhibe, de manera paradigmática y manifiesta, el monumento de Eisenman en Berlín. ABSTRACT 1. Our research focuses on the study of “in-between spaces or environments” at particular times in contemporary architecture, in a transition period from the end of the 1980’s through to today. We aim to analyse how in-between environments are presented in the architectural object or place and their function or their relationship with the nearby surroundings, from the project through to the experience had. 2. In this research, the in-between concept, understood as an interstitial, border and ambivalent (or multi-purpose) environment or space, is assessed from the viewpoint of etymology, science, thought and art, to conclude in current architecture, with specific exploration of the conception process, of the formal, spatial and functional proposal, together with the perception and other experiences in the architectural place. 3. Firstly, we aim to study and explore the “in-between” concept as regards its features, functions and locations within contemporary culture, revealing its most important cultural background, to then apply it reflexively to important works of architecture. The research focuses on the figural (imprecise) mode of in-between (in allusion to Deleuze’s “figural” approach) whose base metaphors are the translucent, semi-darkness and foam, linked to the current cultural paradigm of complexity (C. Jenks). We then go on to assess the relationships or implications of said figural mode in architectural works by Eisenman, Holl, Tschumi, Ito, Fujimoto, Van Berkel and Bos, and Siza, verifying their operational worth and revealing their meaning and importance today and in this discipline. The backdrop of the study is the in-between concept of Eisenman’s work and it also uses concepts from the philosophy of the limit of Trías as its main underpinnings. 4. In each of the architectural works presented, this imprecise mode is translated into a specific in-between environment or space. They are works in which real and virtual, matricial and objectual, architecture and territory, existing and new, collective and individual, social and intimate, interior and exterior and other uses and functions all intertwine or blend together. They are architectures the geometry of which is not so much determined by bi- or tri-dimensional aspects of the drawing or construction. Through the manipulation of these more or less complex, dynamic and interstitial geometries, these works reflect (or insinuate) the premises of the current Zeitgeist: A change in the scheme of objects to relationships towards a more holistic, transdisciplinary, systemic or complex thought (E. Morin), and a new collective conscience about the reality which announces the crisis of perception, the change in paradigm and new values (F. Capra). Another way of feeling and perceiving the world, places and spaces, which little by little is changing the way of thinking and drawing architecture and hence of interacting with it. 5. The meaning of figural in-between space emerges in the increasingly complex, morphological-spatial and functional qualities of a large part of architecture today. Architecture, geometry and computer technology are more than ever intertwined in a freer way to inquire into other ways of thinking and making places, where the “in-between” spaces we research are a testimony. Architectural space becomes affective and interactive, a figural in-between place, formed by interstitial spatiality which seems to allude to something liquid, where shape is more matrix than configuration, space more spatiality than compartment, its function more versatile and multi-purpose than specific or autonomous, and perplexity, imagination and evocation criss-cross each other, becoming obvious. 6. The architecture of in-between places values not only “flat”, “configuration” and “transparency”, but above all “space” and the “relationship” in its interrelations with users and other contexts. From identity to relationality, from representation to presentation, it is an architecture that proposes “other spaces”, which more than spaces are topographies and interstitial spatialities, of tension, transition, transformation, relation, exchange and interaction. They are real and virtual in-between places, that take in both morphology and topology to conquer new spatialities, aiming to depart from the strict “forming”/”morphing” operation in order to explore “spacing”. They are places that derive both from Deleuze’s indiscernibility zone concept, from Buci-Glucksmann´s image-flow concept, from Sloterdijk’s suspension-between, and from the non-objective space referred to by José Gil, and they are embodied in contemporary architecture as tropes of the interstitial. 7. They are the in-between places in architecture today, of haptic spatiality, more “affective”, generative and interactive, where that in-between environment transforms and is transformed, “affects”, “moves” (it makes us move/act) and evokes other places, other possibilities of habitable or occupiable space. The in-between emerges as a place, which paradigmatically and declaredly, Eisenman´s monument in Berlin announces and exhibits. RESUMO 1. A investigação centra-se no estudo dos “âmbitos ou espaços intermédios” em momentos da arquitectura contemporânea, no período de transição entre os finais dos anos 80 e os nossos dias. Pretende-se analisar como se apresenta o âmbito intermédio no objecto ou lugar arquitectónico e sua função ou relação com o meio envolvente, desde o projecto até à sua repercussão na experiencia vivenciada. 2. O conceito de intermédio entendido como âmbito ou espaço intersticial, fronteiriço e ambivalente (ou multivalente), atravessa na presente investigação o campo da etimologia, da ciência, do pensamento e da arte, para deter-se na arquitectura actual, realizando-se uma indagação concreta no processo de concepção, na proposta formal, espacial e funcional, assim como na percepção e demais experiencias ou vivencias no lugar arquitectónico. 3. Em primeiro lugar, explora-se o conceito de “intermédio” nas suas características, funções e concretizações na cultura contemporânea, detectando os seus antecedentes culturais mais importantes, para em seguida aplicá-lo reflexivamente a obras significativas de arquitectura. A investigação centra-se na modalidade figural (imprecisa) do intermédio (alusão ao figural deleuziano) cujas metáforas base são o translúcido, a penumbra e a espuma, relacionadas com o actual paradigma da complexidade (C. Jencks). Em seguida analisam-se as relações ou implicações da referida modalidade figural em obras de arquitectos como Eisenman, Holl, Tschumi, Ito, Fujimoto, Van Berkel e Bos, e Siza, como modo de comprovar o seu valor operativo e revelar o seu sentido e importância na actualidade e na disciplina. O estudo tem como referencia o conceito de in-between da obra de Eisenman, e utiliza conceitos da filosofia do limite de Trias como alguns dos seus principais fundamentos. 4. Em cada uma das obras de arquitectura apresentadas esta modalidade imprecisa traduz-se num âmbito ou espaço intermédia figural especifico. São obras nas quais real e virtual, matricial e objectual, arquitectura e território, existente e novo, colectivo e individual, social e intimo, interior e exterior, e outros usos e funções se entrelaçam ou fundem. São arquitecturas cuja geometria já não está tão determinada por aspectos bi ou tridimensionais do desenho ou da construção. Através do uso destas geometrias mais ou menos complexas, dinâmicas e intersticiais, estas obras reflectem (ou intuem) as premissas do actual zeitgeist: uma mudança de esquemas de objectos a relações para um pensamento mais holístico, transdisciplinar, sistémico ou complexo (E. Morin) e uma nova consciência colectiva sobre a realidade, que anuncia a crise da percepção, a mudança de paradigma e novos valores (F. Capra). Emerge uma outra forma de sentir e perceber o mundo, os lugares e os espaços, que gradualmente vai alterando o modo de pensar e desenhar a arquitectura, e consequentemente de interagir com ela. 5. O sentido do espaço intermédio figural, emerge nas cada vez mais complexas qualidades morfológico-espaciais e funcionais de uma parte importante da arquitectura actual. Cada vez mais, arquitectura, geometria e tecnologia informática, relacionam-se de um modo mais livre para indagar outras formas de pensar e fazer lugares, onde os espaços intermédios que investigamos são um testemunho. O espaço arquitectónico torna-se afectivo e interactivo, um lugar intermédio figural, formalizado por espacialidades intersticiais que parecem aludir ao estado liquido, onde a forma é mais matriz que configuração, o espaço mais espacialidade que compartimento, a função mais versátil e multivalente que especifica ou autónoma, e a perplexidade, a imaginação e a evocação entrecruzam-se e tornam-se patentes. 6. A arquitectura dos lugares intermédios valoriza não só o “plano”, a “configuração” e a “transparência”, mas sobretudo o” espaço” e a ”relação” nas suas inter-relações com os utentes e restante contextos. Da identidade à relacionalidade, da representação à apresentação, é uma arquitectura que propõe “outros espaços”, que além de espaços são topografias e espacialidades intersticiais, de tensão, transição, transformação, relação, intercambio e interacção. São lugares intermédios reais e virtuais que utilizam tanto a morfologia como a topologia para conquistar novas espacialidades, pretendendo ultrapassar a estrita operação de “forming”/“morphing”/formação para explorar a de “spacing”/espaçamento. São lugares que se apoiam tanto no conceito de zona de indescernibilidade de Deleuze, como na de imagem-fluxo de Buci-Glucksmann como no de suspensão–entre de Sloterdijk ou de espaço-não objectivo que refere José Gil, e se plasmam na arquitectura contemporânea como tropos do intersticial. 7. São os lugares intermédios da arquitectura actual, de espacialidade háptica, mais “afectiva”, generativa e interactiva, onde esse âmbito intermédio transforma e é transformado, “afecta”, ”co-move “(nos faz mover/agir) e evoca outros lugares, outras possibilidades de espaço habitável ou ocupável. Emerge o intermédio como lugar que, paradigmática e manifestamente, o monumento de Eisenmann em Berlim, anuncia e exibe.

Estudio y diseño de elementos acústicos para proporcionar una acústica variable en una sala multifuncional

El objetivo de este proyecto es profundizar en el estudio y diseño de sistemas relacionados con el acondicionamiento acústico para una sala multifuncional. El proyecto se compone de dos partes. Una parte teórica y una parte práctica dónde se aplican los conceptos teóricos aprendidos. La primera parte, está dividida en capítulos en los que se habla de los siguientes temas: Acústica de salas. Para obtener una acústica adecuada en un recinto destinado a varias funciones, se debe contar con una serie de características que lo definan según su uso, por lo que es necesario conocer el tiempo de reverberación y otros parámetros subjetivos para poder caracterizar ese recinto. Materiales para el acondicionamiento acústico, donde se habla de los materiales absorbentes clasificándolos según las frecuencias a las que actúan y de los distintos tipos de difusores. Métodos para conseguir una acústica variable mediante la utilización de elementos físicos variables, citando casos reales de salas multifuncionales. La segunda parte, consiste en la realización de diseños de elementos de acústica variable para una posible utilización en salas polivalentes reales. La herramienta elegida a la hora de la elaboración de estos diseños es el AutoCad. Con esta herramienta se han realizado estos diseños representados en dos y tres dimensiones. ABSTRACT. The objective of this project is to deepen the study and design of systems related to multifunctional room acoustic conditioning. The project is composed of two parts. A theoretical part and a practical part where the learned theoretical concepts are applied. The first part is divided into chapters in which we talk about the following topics: Acoustics of rooms. To obtain proper acoustics in a room intended for various functions, you must have a number of characteristics that define it according to its use, so it is necessary to know the reverberation time and other subjective parameters to characterize the hall. Materials for acoustic conditioning, where we talk about the absorbent materials classified according to frequencies that those materials act and the different types of diffusers. Methods for obtain a variable acoustic by using variable physical elements, mentioning real cases of multi-purpose rooms. The second part deals with designs execution of variable acoustic elements for a possible use in a real multipurpose room. The chosen tool to develop these designs is the AutoCad. These designs have been made with this tool, represented in two and three dimensions.

Toward Multi-Scale Object-Based Data Fusion

This paper proposes a new methodology for object based 2-D data fu- sion, with a multiscale character. This methodology is intended to be use in agriculture, specifically in the characterization of the water status of different crops, so as to have an appropriate water management at a farm-holding scale. As a first approach to its evaluation, vegetation cover vigor data has been integrated with texture data. For this purpose, NDVI maps have been calculated using a multispectral image and Lacunarity maps from the panchromatic image. Preliminary results show this methodology is viable in the integration and management of large volumes of data, which characterize the behavior of agricultural covers at farm-holding scale.

Multi-objective Estimation of Distribution Algorithm Based on Joint Modeling of Objectives and Variables

This paper proposes a new multi-objective estimation of distribution algorithm (EDA) based on joint modeling of objectives and variables. This EDA uses the multi-dimensional Bayesian network as its probabilistic model. In this way it can capture the dependencies between objectives, variables and objectives, as well as the dependencies learnt between variables in other Bayesian network-based EDAs. This model leads to a problem decomposition that helps the proposed algorithm to find better trade-off solutions to the multi-objective problem. In addition to Pareto set approximation, the algorithm is also able to estimate the structure of the multi-objective problem. To apply the algorithm to many-objective problems, the algorithm includes four different ranking methods proposed in the literature for this purpose. The algorithm is applied to the set of walking fish group (WFG) problems, and its optimization performance is compared with an evolutionary algorithm and another multi-objective EDA. The experimental results show that the proposed algorithm performs significantly better on many of the problems and for different objective space dimensions, and achieves comparable results on some compared with the other algorithms.

The CIAO Multi-Dialect Compiler and System: An Experimentation Workbench for Future (C)LP Systems

CIAO is an advanced programming environment supporting Logic and Constraint programming. It offers a simple concurrent kernel on top of which declarative and non-declarative extensions are added via librarles. Librarles are available for supporting the ISOProlog standard, several constraint domains, functional and higher order programming, concurrent and distributed programming, internet programming, and others. The source language allows declaring properties of predicates via assertions, including types and modes. Such properties are checked at compile-time or at run-time. The compiler and system architecture are designed to natively support modular global analysis, with the two objectives of proving properties in assertions and performing program optimizations, including transparently exploiting parallelism in programs. The purpose of this paper is to report on recent progress made in the context of the CIAO system, with special emphasis on the capabilities of the compiler, the techniques used for supporting such capabilities, and the results in the áreas of program analysis and transformation already obtained with the system.

Response threshold models, stochastic learning automata and ant colony optimization-based decentralized self-coordination algorithms for heterogeneous multi-tasks distribution in multi-robot systems

In recent decades, there has been an increasing interest in systems comprised of several autonomous mobile robots, and as a result, there has been a substantial amount of development in the eld of Articial Intelligence, especially in Robotics. There are several studies in the literature by some researchers from the scientic community that focus on the creation of intelligent machines and devices capable to imitate the functions and movements of living beings. Multi-Robot Systems (MRS) can often deal with tasks that are dicult, if not impossible, to be accomplished by a single robot. In the context of MRS, one of the main challenges is the need to control, coordinate and synchronize the operation of multiple robots to perform a specic task. This requires the development of new strategies and methods which allow us to obtain the desired system behavior in a formal and concise way. This PhD thesis aims to study the coordination of multi-robot systems, in particular, addresses the problem of the distribution of heterogeneous multi-tasks. The main interest in these systems is to understand how from simple rules inspired by the division of labor in social insects, a group of robots can perform tasks in an organized and coordinated way. We are mainly interested on truly distributed or decentralized solutions in which the robots themselves, autonomously and in an individual manner, select a particular task so that all tasks are optimally distributed. In general, to perform the multi-tasks distribution among a team of robots, they have to synchronize their actions and exchange information. Under this approach we can speak of multi-tasks selection instead of multi-tasks assignment, which means, that the agents or robots select the tasks instead of being assigned a task by a central controller. The key element in these algorithms is the estimation ix of the stimuli and the adaptive update of the thresholds. This means that each robot performs this estimate locally depending on the load or the number of pending tasks to be performed. In addition, it is very interesting the evaluation of the results in function in each approach, comparing the results obtained by the introducing noise in the number of pending loads, with the purpose of simulate the robot's error in estimating the real number of pending tasks. The main contribution of this thesis can be found in the approach based on self-organization and division of labor in social insects. An experimental scenario for the coordination problem among multiple robots, the robustness of the approaches and the generation of dynamic tasks have been presented and discussed. The particular issues studied are: Threshold models: It presents the experiments conducted to test the response threshold model with the objective to analyze the system performance index, for the problem of the distribution of heterogeneous multitasks in multi-robot systems; also has been introduced additive noise in the number of pending loads and has been generated dynamic tasks over time. Learning automata methods: It describes the experiments to test the learning automata-based probabilistic algorithms. The approach was tested to evaluate the system performance index with additive noise and with dynamic tasks generation for the same problem of the distribution of heterogeneous multi-tasks in multi-robot systems. Ant colony optimization: The goal of the experiments presented is to test the ant colony optimization-based deterministic algorithms, to achieve the distribution of heterogeneous multi-tasks in multi-robot systems. In the experiments performed, the system performance index is evaluated by introducing additive noise and dynamic tasks generation over time.

MOIRA-PLUS use in decision making on the long-term management of contaminated freshwater bodies and catchments

In the mid-long-term after a nuclear accident, the contamination of drinking water sources, fish and other aquatic foodstuffs, irrigation supplies and people?s exposure during recreational activities may create considerable public concern, even though dose assessment may in certain situations indicate lesser importance than for other sources, as clearly experienced in the aftermath of past accidents. In such circumstances there are a number of available countermeasure options, ranging from specific chemical treatment of lakes to bans on fish ingestion or on the use of water for crop irrigation. The potential actions can be broadly grouped into four main categories, chemical, biological, physical and social. In some cases a combination of actions may be the optimal strategy and a decision support system (DSS) like MOIRA-PLUS can be of great help to optimise a decision. A further option is of course not to take any remedial actions, although this may also have significant socio-economic repercussions which should be adequately evaluated. MOIRA-PLUS is designed to allow for a reliable assessment of the long-term evolution of the radiological situation and of feasible alternative rehabilitation strategies, including an objective evaluation of their social, economic and ecological impacts in a rational and comprehensive manner. MOIRA-PLUS also features a decision analysis methodology, making use of multi-attribute analysis, which can take into account the preferences and needs of different types of stakeholders. The main functions and elements of the system are described summarily. Also the conclusions from end-user?s experiences with the system are discussed, including exercises involving the organizations responsible for emergency management and the affected services, as well as different local and regional stakeholders. MOIRAPLUS has proven to be a mature system, user friendly and relatively easy to set up. It can help to better decisionmaking by enabling a realistic evaluation of the complete impacts of possible recovery strategies. Also, the interaction with stakeholders has allowed identifying improvements of the system that have been recently implemented.

Sensorless explicit model predictive control for multi-phase buck converters with variable output voltage

The purpose of this paper is to use the predictive control to take advantage of the future information in order to improve the reference tracking. The control attempts to increase the bandwidth of the conventional regulators by using the future information of the reference, which is supposed to be known in advance. A method for designing a controller is also proposed. A comparison in simulation with a conventional regulator is made controlling a four-phase Buck converter. Advantages and disadvantages are analyzed based on simulation results.

Development of the infrastructure for a multi-agent traffic management system simulation

This document contains detailed description of the design and the implementation of a multi-agent application controlling traffic lights in a city together with a system for simulating traffic and testing. The goal of this thesis is to design and build a simplified intelligent and distributed solution to the problem with the traffic in the big cities following different good practices in order to allow future refining of the model of the real world. The problem of the traffic in the big cities is still a problem that cannot be solved. Not only is the increasing number of cars a reason for the traffic jams, but also the way the traffic is organized. Usually, the intersections with traffic lights are replaced by roundabouts or interchanges to increase the number of cars that can cross the intersection in certain time. But still there are places where the infrastructure cannot be changed and the traffic light semaphores are the only way to control the car flows. In real life, the traffic lights have a predefined plan for change or they receive information from a centralized system when and how they have to change. But what if the traffic lights can cooperate and decide on their own when and how to change? Using this problem, the purpose of the thesis is to explore different agent-based software engineering approaches to design and build a non-conventional distributed system. From the software engineering point of view, the goal of the thesis is to apply the knowledge and use the skills, acquired during the various courses of the master program in Software Engineering, while solving a practical and complex problem such as the traffic in the cities.

Parametric and structural self-adaptation of embedded systems using evolvable hardware

Los sistemas empotrados han sido concebidos tradicionalmente como sistemas de procesamiento específicos que realizan una tarea fija durante toda su vida útil. Para cumplir con requisitos estrictos de coste, tamaño y peso, el equipo de diseño debe optimizar su funcionamiento para condiciones muy específicas. Sin embargo, la demanda de mayor versatilidad, un funcionamiento más inteligente y, en definitiva, una mayor capacidad de procesamiento comenzaron a chocar con estas limitaciones, agravado por la incertidumbre asociada a entornos de operación cada vez más dinámicos donde comenzaban a ser desplegados progresivamente. Esto trajo como resultado una necesidad creciente de que los sistemas pudieran responder por si solos a eventos inesperados en tiempo diseño tales como: cambios en las características de los datos de entrada y el entorno del sistema en general; cambios en la propia plataforma de cómputo, por ejemplo debido a fallos o defectos de fabricación; y cambios en las propias especificaciones funcionales causados por unos objetivos del sistema dinámicos y cambiantes. Como consecuencia, la complejidad del sistema aumenta, pero a cambio se habilita progresivamente una capacidad de adaptación autónoma sin intervención humana a lo largo de la vida útil, permitiendo que tomen sus propias decisiones en tiempo de ejecución. Éstos sistemas se conocen, en general, como sistemas auto-adaptativos y tienen, entre otras características, las de auto-configuración, auto-optimización y auto-reparación. Típicamente, la parte soft de un sistema es mayoritariamente la única utilizada para proporcionar algunas capacidades de adaptación a un sistema. Sin embargo, la proporción rendimiento/potencia en dispositivos software como microprocesadores en muchas ocasiones no es adecuada para sistemas empotrados. En este escenario, el aumento resultante en la complejidad de las aplicaciones está siendo abordado parcialmente mediante un aumento en la complejidad de los dispositivos en forma de multi/many-cores; pero desafortunadamente, esto hace que el consumo de potencia también aumente. Además, la mejora en metodologías de diseño no ha sido acorde como para poder utilizar toda la capacidad de cómputo disponible proporcionada por los núcleos. Por todo ello, no se están satisfaciendo adecuadamente las demandas de cómputo que imponen las nuevas aplicaciones. La solución tradicional para mejorar la proporción rendimiento/potencia ha sido el cambio a unas especificaciones hardware, principalmente usando ASICs. Sin embargo, los costes de un ASIC son altamente prohibitivos excepto en algunos casos de producción en masa y además la naturaleza estática de su estructura complica la solución a las necesidades de adaptación. Los avances en tecnologías de fabricación han hecho que la FPGA, una vez lenta y pequeña, usada como glue logic en sistemas mayores, haya crecido hasta convertirse en un dispositivo de cómputo reconfigurable de gran potencia, con una cantidad enorme de recursos lógicos computacionales y cores hardware empotrados de procesamiento de señal y de propósito general. Sus capacidades de reconfiguración han permitido combinar la flexibilidad propia del software con el rendimiento del procesamiento en hardware, lo que tiene la potencialidad de provocar un cambio de paradigma en arquitectura de computadores, pues el hardware no puede ya ser considerado más como estático. El motivo es que como en el caso de las FPGAs basadas en tecnología SRAM, la reconfiguración parcial dinámica (DPR, Dynamic Partial Reconfiguration) es posible. Esto significa que se puede modificar (reconfigurar) un subconjunto de los recursos computacionales en tiempo de ejecución mientras el resto permanecen activos. Además, este proceso de reconfiguración puede ser ejecutado internamente por el propio dispositivo. El avance tecnológico en dispositivos hardware reconfigurables se encuentra recogido bajo el campo conocido como Computación Reconfigurable (RC, Reconfigurable Computing). Uno de los campos de aplicación más exóticos y menos convencionales que ha posibilitado la computación reconfigurable es el conocido como Hardware Evolutivo (EHW, Evolvable Hardware), en el cual se encuentra enmarcada esta tesis. La idea principal del concepto consiste en convertir hardware que es adaptable a través de reconfiguración en una entidad evolutiva sujeta a las fuerzas de un proceso evolutivo inspirado en el de las especies biológicas naturales, que guía la dirección del cambio. Es una aplicación más del campo de la Computación Evolutiva (EC, Evolutionary Computation), que comprende una serie de algoritmos de optimización global conocidos como Algoritmos Evolutivos (EA, Evolutionary Algorithms), y que son considerados como algoritmos universales de resolución de problemas. En analogía al proceso biológico de la evolución, en el hardware evolutivo el sujeto de la evolución es una población de circuitos que intenta adaptarse a su entorno mediante una adecuación progresiva generación tras generación. Los individuos pasan a ser configuraciones de circuitos en forma de bitstreams caracterizados por descripciones de circuitos reconfigurables. Seleccionando aquellos que se comportan mejor, es decir, que tienen una mejor adecuación (o fitness) después de ser evaluados, y usándolos como padres de la siguiente generación, el algoritmo evolutivo crea una nueva población hija usando operadores genéticos como la mutación y la recombinación. Según se van sucediendo generaciones, se espera que la población en conjunto se aproxime a la solución óptima al problema de encontrar una configuración del circuito adecuada que satisfaga las especificaciones. El estado de la tecnología de reconfiguración después de que la familia de FPGAs XC6200 de Xilinx fuera retirada y reemplazada por las familias Virtex a finales de los 90, supuso un gran obstáculo para el avance en hardware evolutivo; formatos de bitstream cerrados (no conocidos públicamente); dependencia de herramientas del fabricante con soporte limitado de DPR; una velocidad de reconfiguración lenta; y el hecho de que modificaciones aleatorias del bitstream pudieran resultar peligrosas para la integridad del dispositivo, son algunas de estas razones. Sin embargo, una propuesta a principios de los años 2000 permitió mantener la investigación en el campo mientras la tecnología de DPR continuaba madurando, el Circuito Virtual Reconfigurable (VRC, Virtual Reconfigurable Circuit). En esencia, un VRC en una FPGA es una capa virtual que actúa como un circuito reconfigurable de aplicación específica sobre la estructura nativa de la FPGA que reduce la complejidad del proceso reconfiguración y aumenta su velocidad (comparada con la reconfiguración nativa). Es un array de nodos computacionales especificados usando descripciones HDL estándar que define recursos reconfigurables ad-hoc: multiplexores de rutado y un conjunto de elementos de procesamiento configurables, cada uno de los cuales tiene implementadas todas las funciones requeridas, que pueden seleccionarse a través de multiplexores tal y como ocurre en una ALU de un microprocesador. Un registro grande actúa como memoria de configuración, por lo que la reconfiguración del VRC es muy rápida ya que tan sólo implica la escritura de este registro, el cual controla las señales de selección del conjunto de multiplexores. Sin embargo, esta capa virtual provoca: un incremento de área debido a la implementación simultánea de cada función en cada nodo del array más los multiplexores y un aumento del retardo debido a los multiplexores, reduciendo la frecuencia de funcionamiento máxima. La naturaleza del hardware evolutivo, capaz de optimizar su propio comportamiento computacional, le convierten en un buen candidato para avanzar en la investigación sobre sistemas auto-adaptativos. Combinar un sustrato de cómputo auto-reconfigurable capaz de ser modificado dinámicamente en tiempo de ejecución con un algoritmo empotrado que proporcione una dirección de cambio, puede ayudar a satisfacer los requisitos de adaptación autónoma de sistemas empotrados basados en FPGA. La propuesta principal de esta tesis está por tanto dirigida a contribuir a la auto-adaptación del hardware de procesamiento de sistemas empotrados basados en FPGA mediante hardware evolutivo. Esto se ha abordado considerando que el comportamiento computacional de un sistema puede ser modificado cambiando cualquiera de sus dos partes constitutivas: una estructura hard subyacente y un conjunto de parámetros soft. De esta distinción, se derivan dos lineas de trabajo. Por un lado, auto-adaptación paramétrica, y por otro auto-adaptación estructural. El objetivo perseguido en el caso de la auto-adaptación paramétrica es la implementación de técnicas de optimización evolutiva complejas en sistemas empotrados con recursos limitados para la adaptación paramétrica online de circuitos de procesamiento de señal. La aplicación seleccionada como prueba de concepto es la optimización para tipos muy específicos de imágenes de los coeficientes de los filtros de transformadas wavelet discretas (DWT, DiscreteWavelet Transform), orientada a la compresión de imágenes. Por tanto, el objetivo requerido de la evolución es una compresión adaptativa y más eficiente comparada con los procedimientos estándar. El principal reto radica en reducir la necesidad de recursos de supercomputación para el proceso de optimización propuesto en trabajos previos, de modo que se adecúe para la ejecución en sistemas empotrados. En cuanto a la auto-adaptación estructural, el objetivo de la tesis es la implementación de circuitos auto-adaptativos en sistemas evolutivos basados en FPGA mediante un uso eficiente de sus capacidades de reconfiguración nativas. En este caso, la prueba de concepto es la evolución de tareas de procesamiento de imagen tales como el filtrado de tipos desconocidos y cambiantes de ruido y la detección de bordes en la imagen. En general, el objetivo es la evolución en tiempo de ejecución de tareas de procesamiento de imagen desconocidas en tiempo de diseño (dentro de un cierto grado de complejidad). En este caso, el objetivo de la propuesta es la incorporación de DPR en EHW para evolucionar la arquitectura de un array sistólico adaptable mediante reconfiguración cuya capacidad de evolución no había sido estudiada previamente. Para conseguir los dos objetivos mencionados, esta tesis propone originalmente una plataforma evolutiva que integra un motor de adaptación (AE, Adaptation Engine), un motor de reconfiguración (RE, Reconfiguration Engine) y un motor computacional (CE, Computing Engine) adaptable. El el caso de adaptación paramétrica, la plataforma propuesta está caracterizada por: • un CE caracterizado por un núcleo de procesamiento hardware de DWT adaptable mediante registros reconfigurables que contienen los coeficientes de los filtros wavelet • un algoritmo evolutivo como AE que busca filtros wavelet candidatos a través de un proceso de optimización paramétrica desarrollado específicamente para sistemas caracterizados por recursos de procesamiento limitados • un nuevo operador de mutación simplificado para el algoritmo evolutivo utilizado, que junto con un mecanismo de evaluación rápida de filtros wavelet candidatos derivado de la literatura actual, asegura la viabilidad de la búsqueda evolutiva asociada a la adaptación de wavelets. En el caso de adaptación estructural, la plataforma propuesta toma la forma de: • un CE basado en una plantilla de array sistólico reconfigurable de 2 dimensiones compuesto de nodos de procesamiento reconfigurables • un algoritmo evolutivo como AE que busca configuraciones candidatas del array usando un conjunto de funcionalidades de procesamiento para los nodos disponible en una biblioteca accesible en tiempo de ejecución • un RE hardware que explota la capacidad de reconfiguración nativa de las FPGAs haciendo un uso eficiente de los recursos reconfigurables del dispositivo para cambiar el comportamiento del CE en tiempo de ejecución • una biblioteca de elementos de procesamiento reconfigurables caracterizada por bitstreams parciales independientes de la posición, usados como el conjunto de configuraciones disponibles para los nodos de procesamiento del array Las contribuciones principales de esta tesis se pueden resumir en la siguiente lista: • Una plataforma evolutiva basada en FPGA para la auto-adaptación paramétrica y estructural de sistemas empotrados compuesta por un motor computacional (CE), un motor de adaptación (AE) evolutivo y un motor de reconfiguración (RE). Esta plataforma se ha desarrollado y particularizado para los casos de auto-adaptación paramétrica y estructural. • En cuanto a la auto-adaptación paramétrica, las contribuciones principales son: – Un motor computacional adaptable mediante registros que permite la adaptación paramétrica de los coeficientes de una implementación hardware adaptativa de un núcleo de DWT. – Un motor de adaptación basado en un algoritmo evolutivo desarrollado específicamente para optimización numérica, aplicada a los coeficientes de filtros wavelet en sistemas empotrados con recursos limitados. – Un núcleo IP de DWT auto-adaptativo en tiempo de ejecución para sistemas empotrados que permite la optimización online del rendimiento de la transformada para compresión de imágenes en entornos específicos de despliegue, caracterizados por tipos diferentes de señal de entrada. – Un modelo software y una implementación hardware de una herramienta para la construcción evolutiva automática de transformadas wavelet específicas. • Por último, en cuanto a la auto-adaptación estructural, las contribuciones principales son: – Un motor computacional adaptable mediante reconfiguración nativa de FPGAs caracterizado por una plantilla de array sistólico en dos dimensiones de nodos de procesamiento reconfigurables. Es posible mapear diferentes tareas de cómputo en el array usando una biblioteca de elementos sencillos de procesamiento reconfigurables. – Definición de una biblioteca de elementos de procesamiento apropiada para la síntesis autónoma en tiempo de ejecución de diferentes tareas de procesamiento de imagen. – Incorporación eficiente de la reconfiguración parcial dinámica (DPR) en sistemas de hardware evolutivo, superando los principales inconvenientes de propuestas previas como los circuitos reconfigurables virtuales (VRCs). En este trabajo también se comparan originalmente los detalles de implementación de ambas propuestas. – Una plataforma tolerante a fallos, auto-curativa, que permite la recuperación funcional online en entornos peligrosos. La plataforma ha sido caracterizada desde una perspectiva de tolerancia a fallos: se proponen modelos de fallo a nivel de CLB y de elemento de procesamiento, y usando el motor de reconfiguración, se hace un análisis sistemático de fallos para un fallo en cada elemento de procesamiento y para dos fallos acumulados. – Una plataforma con calidad de filtrado dinámica que permite la adaptación online a tipos de ruido diferentes y diferentes comportamientos computacionales teniendo en cuenta los recursos de procesamiento disponibles. Por un lado, se evolucionan filtros con comportamientos no destructivos, que permiten esquemas de filtrado en cascada escalables; y por otro, también se evolucionan filtros escalables teniendo en cuenta requisitos computacionales de filtrado cambiantes dinámicamente. Este documento está organizado en cuatro partes y nueve capítulos. La primera parte contiene el capítulo 1, una introducción y motivación sobre este trabajo de tesis. A continuación, el marco de referencia en el que se enmarca esta tesis se analiza en la segunda parte: el capítulo 2 contiene una introducción a los conceptos de auto-adaptación y computación autonómica (autonomic computing) como un campo de investigación más general que el muy específico de este trabajo; el capítulo 3 introduce la computación evolutiva como la técnica para dirigir la adaptación; el capítulo 4 analiza las plataformas de computación reconfigurables como la tecnología para albergar hardware auto-adaptativo; y finalmente, el capítulo 5 define, clasifica y hace un sondeo del campo del hardware evolutivo. Seguidamente, la tercera parte de este trabajo contiene la propuesta, desarrollo y resultados obtenidos: mientras que el capítulo 6 contiene una declaración de los objetivos de la tesis y la descripción de la propuesta en su conjunto, los capítulos 7 y 8 abordan la auto-adaptación paramétrica y estructural, respectivamente. Finalmente, el capítulo 9 de la parte 4 concluye el trabajo y describe caminos de investigación futuros. ABSTRACT Embedded systems have traditionally been conceived to be specific-purpose computers with one, fixed computational task for their whole lifetime. Stringent requirements in terms of cost, size and weight forced designers to highly optimise their operation for very specific conditions. However, demands for versatility, more intelligent behaviour and, in summary, an increased computing capability began to clash with these limitations, intensified by the uncertainty associated to the more dynamic operating environments where they were progressively being deployed. This brought as a result an increasing need for systems to respond by themselves to unexpected events at design time, such as: changes in input data characteristics and system environment in general; changes in the computing platform itself, e.g., due to faults and fabrication defects; and changes in functional specifications caused by dynamically changing system objectives. As a consequence, systems complexity is increasing, but in turn, autonomous lifetime adaptation without human intervention is being progressively enabled, allowing them to take their own decisions at run-time. This type of systems is known, in general, as selfadaptive, and are able, among others, of self-configuration, self-optimisation and self-repair. Traditionally, the soft part of a system has mostly been so far the only place to provide systems with some degree of adaptation capabilities. However, the performance to power ratios of software driven devices like microprocessors are not adequate for embedded systems in many situations. In this scenario, the resulting rise in applications complexity is being partly addressed by rising devices complexity in the form of multi and many core devices; but sadly, this keeps on increasing power consumption. Besides, design methodologies have not been improved accordingly to completely leverage the available computational power from all these cores. Altogether, these factors make that the computing demands new applications pose are not being wholly satisfied. The traditional solution to improve performance to power ratios has been the switch to hardware driven specifications, mainly using ASICs. However, their costs are highly prohibitive except for some mass production cases and besidesthe static nature of its structure complicates the solution to the adaptation needs. The advancements in fabrication technologies have made that the once slow, small FPGA used as glue logic in bigger systems, had grown to be a very powerful, reconfigurable computing device with a vast amount of computational logic resources and embedded, hardened signal and general purpose processing cores. Its reconfiguration capabilities have enabled software-like flexibility to be combined with hardware-like computing performance, which has the potential to cause a paradigm shift in computer architecture since hardware cannot be considered as static anymore. This is so, since, as is the case with SRAMbased FPGAs, Dynamic Partial Reconfiguration (DPR) is possible. This means that subsets of the FPGA computational resources can now be changed (reconfigured) at run-time while the rest remains active. Besides, this reconfiguration process can be triggered internally by the device itself. This technological boost in reconfigurable hardware devices is actually covered under the field known as Reconfigurable Computing. One of the most exotic fields of application that Reconfigurable Computing has enabled is the known as Evolvable Hardware (EHW), in which this dissertation is framed. The main idea behind the concept is turning hardware that is adaptable through reconfiguration into an evolvable entity subject to the forces of an evolutionary process, inspired by that of natural, biological species, that guides the direction of change. It is yet another application of the field of Evolutionary Computation (EC), which comprises a set of global optimisation algorithms known as Evolutionary Algorithms (EAs), considered as universal problem solvers. In analogy to the biological process of evolution, in EHW the subject of evolution is a population of circuits that tries to get adapted to its surrounding environment by progressively getting better fitted to it generation after generation. Individuals become circuit configurations representing bitstreams that feature reconfigurable circuit descriptions. By selecting those that behave better, i.e., with a higher fitness value after being evaluated, and using them as parents of the following generation, the EA creates a new offspring population by using so called genetic operators like mutation and recombination. As generations succeed one another, the whole population is expected to approach to the optimum solution to the problem of finding an adequate circuit configuration that fulfils system objectives. The state of reconfiguration technology after Xilinx XC6200 FPGA family was discontinued and replaced by Virtex families in the late 90s, was a major obstacle for advancements in EHW; closed (non publicly known) bitstream formats; dependence on manufacturer tools with highly limiting support of DPR; slow speed of reconfiguration; and random bitstream modifications being potentially hazardous for device integrity, are some of these reasons. However, a proposal in the first 2000s allowed to keep investigating in this field while DPR technology kept maturing, the Virtual Reconfigurable Circuit (VRC). In essence, a VRC in an FPGA is a virtual layer acting as an application specific reconfigurable circuit on top of an FPGA fabric that reduces the complexity of the reconfiguration process and increases its speed (compared to native reconfiguration). It is an array of computational nodes specified using standard HDL descriptions that define ad-hoc reconfigurable resources; routing multiplexers and a set of configurable processing elements, each one containing all the required functions, which are selectable through functionality multiplexers as in microprocessor ALUs. A large register acts as configuration memory, so VRC reconfiguration is very fast given it only involves writing this register, which drives the selection signals of the set of multiplexers. However, large overheads are introduced by this virtual layer; an area overhead due to the simultaneous implementation of every function in every node of the array plus the multiplexers, and a delay overhead due to the multiplexers, which also reduces maximum frequency of operation. The very nature of Evolvable Hardware, able to optimise its own computational behaviour, makes it a good candidate to advance research in self-adaptive systems. Combining a selfreconfigurable computing substrate able to be dynamically changed at run-time with an embedded algorithm that provides a direction for change, can help fulfilling requirements for autonomous lifetime adaptation of FPGA-based embedded systems. The main proposal of this thesis is hence directed to contribute to autonomous self-adaptation of the underlying computational hardware of FPGA-based embedded systems by means of Evolvable Hardware. This is tackled by considering that the computational behaviour of a system can be modified by changing any of its two constituent parts: an underlying hard structure and a set of soft parameters. Two main lines of work derive from this distinction. On one side, parametric self-adaptation and, on the other side, structural self-adaptation. The goal pursued in the case of parametric self-adaptation is the implementation of complex evolutionary optimisation techniques in resource constrained embedded systems for online parameter adaptation of signal processing circuits. The application selected as proof of concept is the optimisation of Discrete Wavelet Transforms (DWT) filters coefficients for very specific types of images, oriented to image compression. Hence, adaptive and improved compression efficiency, as compared to standard techniques, is the required goal of evolution. The main quest lies in reducing the supercomputing resources reported in previous works for the optimisation process in order to make it suitable for embedded systems. Regarding structural self-adaptation, the thesis goal is the implementation of self-adaptive circuits in FPGA-based evolvable systems through an efficient use of native reconfiguration capabilities. In this case, evolution of image processing tasks such as filtering of unknown and changing types of noise and edge detection are the selected proofs of concept. In general, evolving unknown image processing behaviours (within a certain complexity range) at design time is the required goal. In this case, the mission of the proposal is the incorporation of DPR in EHW to evolve a systolic array architecture adaptable through reconfiguration whose evolvability had not been previously checked. In order to achieve the two stated goals, this thesis originally proposes an evolvable platform that integrates an Adaptation Engine (AE), a Reconfiguration Engine (RE) and an adaptable Computing Engine (CE). In the case of parametric adaptation, the proposed platform is characterised by: • a CE featuring a DWT hardware processing core adaptable through reconfigurable registers that holds wavelet filters coefficients • an evolutionary algorithm as AE that searches for candidate wavelet filters through a parametric optimisation process specifically developed for systems featured by scarce computing resources • a new, simplified mutation operator for the selected EA, that together with a fast evaluation mechanism of candidate wavelet filters derived from existing literature, assures the feasibility of the evolutionary search involved in wavelets adaptation In the case of structural adaptation, the platform proposal takes the form of: • a CE based on a reconfigurable 2D systolic array template composed of reconfigurable processing nodes • an evolutionary algorithm as AE that searches for candidate configurations of the array using a set of computational functionalities for the nodes available in a run time accessible library • a hardware RE that exploits native DPR capabilities of FPGAs and makes an efficient use of the available reconfigurable resources of the device to change the behaviour of the CE at run time • a library of reconfigurable processing elements featured by position-independent partial bitstreams used as the set of available configurations for the processing nodes of the array Main contributions of this thesis can be summarised in the following list. • An FPGA-based evolvable platform for parametric and structural self-adaptation of embedded systems composed of a Computing Engine, an evolutionary Adaptation Engine and a Reconfiguration Engine. This platform is further developed and tailored for both parametric and structural self-adaptation. • Regarding parametric self-adaptation, main contributions are: – A CE adaptable through reconfigurable registers that enables parametric adaptation of the coefficients of an adaptive hardware implementation of a DWT core. – An AE based on an Evolutionary Algorithm specifically developed for numerical optimisation applied to wavelet filter coefficients in resource constrained embedded systems. – A run-time self-adaptive DWT IP core for embedded systems that allows for online optimisation of transform performance for image compression for specific deployment environments characterised by different types of input signals. – A software model and hardware implementation of a tool for the automatic, evolutionary construction of custom wavelet transforms. • Lastly, regarding structural self-adaptation, main contributions are: – A CE adaptable through native FPGA fabric reconfiguration featured by a two dimensional systolic array template of reconfigurable processing nodes. Different processing behaviours can be automatically mapped in the array by using a library of simple reconfigurable processing elements. – Definition of a library of such processing elements suited for autonomous runtime synthesis of different image processing tasks. – Efficient incorporation of DPR in EHW systems, overcoming main drawbacks from the previous approach of virtual reconfigurable circuits. Implementation details for both approaches are also originally compared in this work. – A fault tolerant, self-healing platform that enables online functional recovery in hazardous environments. The platform has been characterised from a fault tolerance perspective: fault models at FPGA CLB level and processing elements level are proposed, and using the RE, a systematic fault analysis for one fault in every processing element and for two accumulated faults is done. – A dynamic filtering quality platform that permits on-line adaptation to different types of noise and different computing behaviours considering the available computing resources. On one side, non-destructive filters are evolved, enabling scalable cascaded filtering schemes; and on the other, size-scalable filters are also evolved considering dynamically changing computational filtering requirements. This dissertation is organized in four parts and nine chapters. First part contains chapter 1, the introduction to and motivation of this PhD work. Following, the reference framework in which this dissertation is framed is analysed in the second part: chapter 2 features an introduction to the notions of self-adaptation and autonomic computing as a more general research field to the very specific one of this work; chapter 3 introduces evolutionary computation as the technique to drive adaptation; chapter 4 analyses platforms for reconfigurable computing as the technology to hold self-adaptive hardware; and finally chapter 5 defines, classifies and surveys the field of Evolvable Hardware. Third part of the work follows, which contains the proposal, development and results obtained: while chapter 6 contains an statement of the thesis goals and the description of the proposal as a whole, chapters 7 and 8 address parametric and structural self-adaptation, respectively. Finally, chapter 9 in part 4 concludes the work and describes future research paths.