SERVICE NEEDS FORECASTING: An Approach for the Motor Industry Using Analogies with Medical ER Management Models.

During the past years, the industry has shifted position and moved towards “the luxury universe” whose customers are demanding, treating individuals as unique and valued customer for the business, offering vehicles produced with the state of the art technologies and implementing the highest finishing standards. Due to the competitive level in the market, motor makers enable processes which equalizes customer services to E.R. management, being dealt with the maximum urgency that allows the comparison between both, car workshops and emergency rooms, where workshop bays or ramps will be equal to emergency boxes and skilled technicians are equivalent to the health care specialist, who will carry out tests and checks prior to afford any final operation, keeping the “patient” under control before it is back to normal utilization. This paper ratify a valid model for the automotive industry to estimate customer service demand forecasting under variable demand conditions using analogies with patient demand models used for the medical ER

Environmental assessment of low speed policies for motor vehicle mobility in city centres

streets in local residential areas in large cities, real traffic tests for pollutant emissions and fuel consumption have been carried out in Madrid city centre. Emission concentration and car activity were simultaneously measured by a Portable Emissions Measurement System. Real life tests carried out at different times and on different days were performed with a turbo-diesel engine light vehicle equipped with an oxidizer catalyst and using different driving styles with a previously trained driver. The results show that by reducing the speed limit from 50 km h-1 to 30 km h-1, using a normal driving style, the time taken for a given trip does not increase, but fuel consumption and NOx, CO and PM emissions are clearly reduced. Therefore, the main conclusion of this work is that reducing the speed limit in some narrow streets in residential and commercial areas or in a city not only increases pedestrian safety, but also contributes to reducing the environmental impact of motor vehicles and reducing fuel consumption. In addition, there is also a reduction in the greenhouse gas emissions resulting from the combustion of the fuel.

Sistema para cambiar la geometría de un motor

En este proyecto se desarrolla un sistema electrónico para variar la geometría de un motor de un monoplaza que participa en la competición Fórmula SAE. Fórmula SAE es una competición de diseño de monoplazas para estudiantes, organizado por “Society of Automotive Enginners” (SAE). Este concurso busca la innovación tecnológica de la automoción, así como que estudiantes participen en un trabajo real, en el cual el objetivo es obtener resultados competitivos cumpliendo con una serie de requisitos. La variación de la geometría de un motor en un vehículo permite mejorar el rendimiento del monoplaza consiguiendo elevar el par de potencia del motor. Cualquier mejora en del vehículo en un ámbito de competición puede resultar determinante en el desenlace de la misma. El objetivo del proyecto es realizar esta variación mediante el control de la longitud de los tubos de admisión de aire o “runners” del motor de combustión, empleando un motor lineal paso a paso. A partir de la información obtenida por sensores de revoluciones del motor de combustión y la posición del acelerador se debe controlar la distancia de dichos tubos. Integrando este sistema en el bus CAN del vehículo para que comparta la información medida al resto de módulos. Por todo esto se realiza un estudio aclarando los aspectos generales del objetivo del trabajo, para la comprensión del proyecto a realizar, las posibilidades de realización y adquisición de conocimientos para un mejor desarrollo. Se presenta una solución basada en el control del motor lineal paso a paso mediante el microcontrolador PIC32MX795F512-L. Dispositivo del fabricante Microchip con una arquitectura de 32 bits. Este dispone de un módulo CAN integrado y distintos periféricos que se emplean en la medición de los sensores y actuación sobre el motor paso a paso empleando el driver de Texas Instruments DRV8805. Entonces el trabajo se realiza en dos líneas, una parte software de programación del control del sistema, empleando el software de Microchip MPLABX IDE y otra parte hardware de diseño de una PCB y circuitos acondicionadores para la conexión del microcontrolador, con los sensores, driver, motor paso a paso y bus CAN. El software empleado para la realización de la PCB es Orcad9.2/Layout. Para la evaluación de las medidas obtenidas por los sensores y la comprobación del bus CAN se emplea el kit de desarrollo de Microchip, MCP2515 CAN Bus Monitor Demo Board, que permite ver la información en el bus CAN e introducir tramas al mismo. ABSTRACT. This project develops an electronic system to vary the geometry of a car engine which runs the Formula SAE competition. Formula SAE is a design car competition for students, organized by "Society of Automotive Engineers" (SAE). This competition seeks technological innovation in the automotive industry and brings in students to participate in a real job, in which the objective is to obtain competitive results in compliance with certain requirements. Varying engine’s geometry in a vehicle improves car’s performance raising engine output torque. Any improvement in the vehicle in a competition field can be decisive in the outcome of it. The goal of the project is the variation by controlling the length of the air intake pipe or "runners" in a combustion engine, using a linear motor step. For these, uses the information gathered by speed sensors from the combustion engine and by the throttle position to control the distance of these tubes. This system is integrated in the vehicle CAN bus to share the information with the other modules. For all this is made a study to clarify the general aspects of the project in order to understand the activities developed inside the project, the different options available and also, to acquire knowledge for a better development of the project. The solution is based on linear stepper motor control by the microcontroller PIC32MX795F512-L. Device from manufacturer Microchip with a 32-bit architecture. This module has an integrated CAN various peripherals that are used in measuring the performance of the sensors and drives the stepper motor using Texas Instruments DRV8805 driver. Then the work is done in two lines, first, control programming software system using software MPLABX Microchip IDE and, second, hardware design of a PCB and conditioning circuits for connecting the microcontroller, with sensors, driver stepper motor and CAN bus. The software used to carry out the PCB is Orcad9.2/Layout. For the evaluation of the measurements obtained by the sensors and CAN bus checking is used Microchip development kit, MCP2515 CAN Bus Monitor Demo Board, that allows you to see the information on the CAN bus and enter new frames in the bus.