Optical and structural properties of InAlN/GaN Bragg reflectors examined by transmission electron microscopy and electron energy loss spectroscopy

Molecular beam epitaxy growth of ten-period lattice-matched InAlN/GaN distributed Bragg reflectors (DBRs) with peak reflectivity centered around 400nm is reported including optical and transmission electron microscopy (TEM) measurements [1]. Good periodicity heterostructures with crack-free surfaces were confirmed, but, also a significant residual optical absorption below the bandgap was measured. The TEM characterization ascribes the origin of this problem to polymorfism and planar defects in the GaN layers and to the existence of an In-rich layer at the InAlN/GaN interfaces. In this work, several TEM based techniques have been combined.

Three-dimensional spatial distribution of synapses in the neocortex: A dual-beam electron microscopy study

In the cerebral cortex, most synapses are found in the neuropil, but relatively little is known about their 3-dimensional organization. Using an automated dual-beam electron microscope that combines focused ion beam milling and scanning electron microscopy, we have been able to obtain 10 three-dimensional samples with an average volume of 180 µm(3) from the neuropil of layer III of the young rat somatosensory cortex (hindlimb representation). We have used specific software tools to fully reconstruct 1695 synaptic junctions present in these samples and to accurately quantify the number of synapses per unit volume. These tools also allowed us to determine synapse position and to analyze their spatial distribution using spatial statistical methods. Our results indicate that the distribution of synaptic junctions in the neuropil is nearly random, only constrained by the fact that synapses cannot overlap in space. A theoretical model based on random sequential absorption, which closely reproduces the actual distribution of synapses, is also presented.

Estimation of the solubility parameters of model plant surfaces and agrochemicals: a valuable tool for understanding plant surface interactions

Background Most aerial plant parts are covered with a hydrophobic lipid-rich cuticle, which is the interface between the plant organs and the surrounding environment. Plant surfaces may have a high degree of hydrophobicity because of the combined effects of surface chemistry and roughness. The physical and chemical complexity of the plant cuticle limits the development of models that explain its internal structure and interactions with surface-applied agrochemicals. In this article we introduce a thermodynamic method for estimating the solubilities of model plant surface constituents and relating them to the effects of agrochemicals. Results Following the van Krevelen and Hoftyzer method, we calculated the solubility parameters of three model plant species and eight compounds that differ in hydrophobicity and polarity. In addition, intact tissues were examined by scanning electron microscopy and the surface free energy, polarity, solubility parameter and work of adhesion of each were calculated from contact angle measurements of three liquids with different polarities. By comparing the affinities between plant surface constituents and agrochemicals derived from (a) theoretical calculations and (b) contact angle measurements we were able to distinguish the physical effect of surface roughness from the effect of the chemical nature of the epicuticular waxes. A solubility parameter model for plant surfaces is proposed on the basis of an increasing gradient from the cuticular surface towards the underlying cell wall. Conclusions The procedure enabled us to predict the interactions among agrochemicals, plant surfaces, and cuticular and cell wall components, and promises to be a useful tool for improving our understanding of biological surface interactions.

Estimation of the solubility parameters of model plant surfaces and agrochemicals: a valuable tool for understanding plant surface interactions

Background Most aerial plant parts are covered with a hydrophobic lipid-rich cuticle, which is the interface between the plant organs and the surrounding environment. Plant surfaces may have a high degree of hydrophobicity because of the combined effects of surface chemistry and roughness. The physical and chemical complexity of the plant cuticle limits the development of models that explain its internal structure and interactions with surface-applied agrochemicals. In this article we introduce a thermodynamic method for estimating the solubilities of model plant surface constituents and relating them to the effects of agrochemicals. Results Following the van Krevelen and Hoftyzer method, we calculated the solubility parameters of three model plant species and eight compounds that differ in hydrophobicity and polarity. In addition, intact tissues were examined by scanning electron microscopy and the surface free energy, polarity, solubility parameter and work of adhesion of each were calculated from contact angle measurements of three liquids with different polarities. By comparing the affinities between plant surface constituents and agrochemicals derived from (a) theoretical calculations and (b) contact angle measurements we were able to distinguish the physical effect of surface roughness from the effect of the chemical nature of the epicuticular waxes. A solubility parameter model for plant surfaces is proposed on the basis of an increasing gradient from the cuticular surface towards the underlying cell wall. Conclusions The procedure enabled us to predict the interactions among agrochemicals, plant surfaces, and cuticular and cell wall components, and promises to be a useful tool for improving our understanding of biological surface interactions.

Highly conductive coatings of carbon black/silica composites obtained by a sol-gel process

Conductive submicronic coatings of carbon black (CB)/silica composites have been prepared by a sol-gel process and deposited by spray-coating on glazed porcelain tiles. Stable CB dispersions with surfactant were rheologically characterized to determine the optimum CB-surfactant ratio. The composites were analyzed by Differential Thermal and Thermogravimetric Analysis and Hg-Porosimetry. Thin coatings were thermally treated in the temperature range of 300-500degC in air atmosphere. The microstructure of the coatings was determined by scanning electron microscopy and the structure evaluated by confocal Raman spectroscopy. The electrical characterization of the samples was carried out using dc intensity-voltage curves. The coatings exhibit good adhesion, high density and homogeneous distribution of the conductive filler (CB) in the insulate matrix (silica) that protects against the thermal degradation of the CB nanoparticles during the sintering process. As consequence, the composite coatings show the lowest resistivity values for CB-based films reported in the literature, with values of ~7times10 -5Omegam.

Fungal biodeterioration of colour cinematographic films of the cultural heritage of Cuba

Until recently, cinematographic film was largely cellulose-triacetate-based. However, this material is highly susceptible to biodeterioration, thus placing historic film collections, an important part of the cultural heritage of many countries, at risk. In the present study, samples taken from several biodeteriorated color cinematographic films belonging to the collection of the Cuban Institute for Cinematographic Industry and Arts (ICAIC) were investigated. Infrared spectroscopy showed that all films were of the same composition, i.e., a gelatin emulsion coating one side of a cellulose-triacetate-based film support. The films were analyzed by environmental scanning electron microscopy and scanning electron microscopy to determine the degree of biodeterioration and the type of colonizing microorganisms. Significant fungal colonization was found on both sides of the films in all samples, with a higher concentration of fungi on the gelatin emulsion side. Epifluorescence microscopy of fluorochrome-dyed films demonstrated that some of the fungi were still active, indicating that the films under study, and probably others at the ICAIC, are at risk of further deterioration. Fungi were identified by molecular biology techniques. The fungi mainly responsible for the observed biodeterioration were those belonging to the genera Aspergillus and Cladosporium, although other genera, such as Microascus and Penicillium, were identified as well. In accordance with the findings described herein, the existing guidelines for the prevention and control of film biodeterioration are discussed.

Diseño y evaluación de un procedimiento on-line para la biorremediación de aguas radiactivas en centrales nucleares

Recientemente se ha demostrado la existencia de microorganismos en las piscinas de almacenamiento de combustible nuclear gastado en las centrales nucleares utilizando técnicas convencionales de cultivo en el laboratorio. Estudios posteriores han puesto de manifiesto que los microorganismos presentes eran capaces de colonizar las paredes de acero inoxidable de las piscinas formando biopelículas. Adicionalmente se ha observado la capacidad de estas biopelículas de retener radionúclidos, lo que hace pensar en la posibilidad de utilizarlas en la descontaminación de las aguas radiactivas de las piscinas. En la presente tesis se plantea conocer más profundamente la biodiversidad microbiana de las biopelículas utilizando técnicas de biología molecular como la clonación, además de desarrollar un sistema de descontaminación a escala piloto con el objetivo de valorar si el proceso podría resultar escalable a nivel industrial. Para ello se diseñaron y fabricaron dos biorreactores en acero inoxidable compatibles con las condiciones específicas de seguridad sísmica y protección frente a la radiación en la zona controlada de una central nuclear. Los biorreactores se instalaron en la Central Nuclear de Cofrentes (Valencia) en las proximidades de las piscinas de almacenamiento de combustible nuclear gastado y precediendo a las resinas de intercambio iónico, de forma que reciben el agua de las piscinas permitiendo el análisis in situ de la radiación eliminada del agua de las mismas. Se conectó una lámpara de luz ultravioleta a uno de los biorreactores para poder comparar el desarrollo de bipelículas y la retención de radiactividad en ambas condiciones. En estos biorreactores se introdujeron ovillos de acero inoxidable y de titanio que se extrajeron a diversos tiempos, hasta 635 días para los ovillos de acero inoxidable y hasta 309 días para los ovillos de titanio. Se analizaron las biopelículas desarrolladas sobre los ovillos por microscopía electrónica de barrido y por microscopía de epifluorescencia. Se extrajo el ADN de las biopelículas y, tras su clonación, se identificaron los microorganismos por técnicas independientes de cultivo. Asimismo se determinó por espectrometría gamma la capacidad de las biopelículas para retener radionúclidos. Los microorganismos radiorresistentes identificados pertenecen a los grupos filogenéticos Alpha-proteobacteria, Gamma-proteobacteria, Actinobacteria, Deinococcus-Thermus y Bacteroidetes. Las secuencias de estos microorganismos se han depositado en el GenBank con los números de acceso KR817260-KR817405. Se ha observado una distribución porcentual ligeramente diferente en relación con el tipo de biorreactor. Las biopelículas han retenido fundamentalmente radionúclidos de activación. La suma de Co-60 y Mn-54 ha llegado en ocasiones al 97%. Otros radionúclidos retenidos han sido Cr-51, Co-58, Fe-59, Zn-65 y Zr-95. Se sugiere un mecanismo del proceso de retención de radionúclidos relacionado con el tiempo de formación y desaparición de las biopelículas. Se ha valorado que el proceso escalable puede ser económicamente rentable. ABSTRACT The existence of microorganisms in spent nuclear fuel pools has been demonstrated recently in nuclear power plants by using conventional microbial techniques. Subsequent studies have revealed that those microorganisms were able to colonize the stainless steel pool walls forming biofilms. Additionally, it has been observed the ability of these biofilms to retain radionuclides, which suggests the possibility of using them for radioactive water decontamination purposes. This thesis presents deeper knowledge of microbial biofilms biodiversity by using molecular biology techniques such as cloning, and develops a decontamination system on a pilot scale, in order to assess whether the process could be scalable to an industrial level. Aiming to demonstrate this was feasible, two stainless steel bioreactors were designed and manufactured, both were compatible with seismic and radiation protection standards in the controlled zone of a nuclear plant. These bioreactors were installed in the Cofrentes Nuclear Power Plant (Valencia) next to the spent nuclear fuel pools and preceding (upstream) ion exchange resins. This configuration allowed the bioreactors to receive water directly from the pools allowing in situ analysis of radiation removal. One ultraviolet lamp was connected to one of the bioreactors to compare biofilms development and radioactivity retention in both conditions. Stainless steel and titanium balls were introduced into these bioreactors and were removed after different time periods, up to 635 days for stainless steel balls and up to 309 days for titanium. Biofilms developed on the balls were analyzed by scanning electron microscopy and epifluorescence microscopy. DNA was extracted from the biofilms, was cloned and then the microorganisms were identified by independent culture techniques. Biofilms ability to retain radionuclides was also determined by gamma spectrometry. The identified radioresistant organisms belong to the phylogenetic groups Alphaproteobacteria, Gamma-proteobacteria, Actinobacteria, Deinococcus-Thermus and Bacteroidetes. The sequences of these microorganisms have been deposited in GenBank (access numbers KR817260-KR817405). A different distribution of microorganisms was observed in relation to the type of bioreactor. Biofilms have essentially retained activation radionuclides. Sometimes the sum of Co-60 and Mn-54 reached 97%. Cr-51, Co-58, Fe-59, Zn-65 and Zr-95 have also been retained. A radionuclide retention process mechanism related to biofilms formation and disappearance time is suggested. It has been assessed that the scalable process can be economically profitable.

ESPINA: a tool for the automated segmentation and counting of synapses in large stacks of electron microscopy images

The synapses in the cerebral cortex can be classified into two main types, Gray’s type I and type II, which correspond to asymmetric (mostly glutamatergic excitatory) and symmetric (inhibitory GABAergic) synapses, respectively. Hence, the quantification and identification of their different types and the proportions in which they are found, is extraordinarily important in terms of brain function. The ideal approach to calculate the number of synapses per unit volume is to analyze 3D samples reconstructed from serial sections. However, obtaining serial sections by transmission electron microscopy is an extremely time consuming and technically demanding task. Using focused ion beam/scanning electron microscope microscopy, we recently showed that virtually all synapses can be accurately identified as asymmetric or symmetric synapses when they are visualized, reconstructed, and quantified from large 3D tissue samples obtained in an automated manner. Nevertheless, the analysis, segmentation, and quantification of synapses is still a labor intensive procedure. Thus, novel solutions are currently necessary to deal with the large volume of data that is being generated by automated 3D electron microscopy. Accordingly, we have developed ESPINA, a software tool that performs the automated segmentation and counting of synapses in a reconstructed 3D volume of the cerebral cortex, and that greatly facilitates and accelerates these processes.