Room temperature absorption in laterally biased Quantum Infrared Detectors fabricated by MBE regrowth

In this paper, we show room temperature operation of a quantum well infrared photodetector (QWIP) using lateral conduction through ohmic contacts deposited at both sides of two n-doped quantum wells. To reduce the dark current due to direct conduction in the wells, we apply an electric field between the quantum wells and two pinch-off Schottky gates, in a fashion similar to a field effect device. Since the normal incidence absorption is strongly reduced in intersubband transitions in quantum wells, we first analyze the response of a detector based on quantum dots (QD). This QD device shows photocurrent signal up to 150 K when it is processed in conventional vertical detector. However, it is possible to observe room temperature signal when it is processed in a lateral structure. Finally, the room temperature photoresponse of the QWIP is demonstrated, and compared with theory. An excellent agreement between the estimated and measured characteristics of the device is found

Twinning and grain subdivision during dynamic deformation of a Mg AZ31 sheet alloy at room temperature

The microstructural evolution of an AZ31 rolled sheet during dynamic deformation at strain rates of ∼103 s−1 has been investigated by electron backscatter diffraction, X-ray and neutron diffraction. The influence of orientation on the predominant deformation mechanisms and on the recovery processes taking place during deformation has been systematically examined. The results have been compared with those corresponding to the same alloy tested quasi-statically under equivalent conditions. It has been found that strain rate enhances the activation of extension twinning dramatically, while contraction and secondary twinning are not significantly influenced. The polarity of extension twinning is even reversed in some grains under selected testing conditions. Significant grain subdivision by the formation of geometrically necessary boundaries (GNBs) takes place during both quasi-static and dynamic deformation of this AZ31 alloy. It is remarkable that GNBs of high misorientations form even at the highest strain rates. The phenomenon of recovery has been found to be orientation dependent

Gas sensor based on room temperature optical properties of Surface QDs

Self-organized InGaAs QDs are intensively studied for optoelectronic applications. Several approaches are in study to reach the emission wavelengths needed for these applications. The use of antimony (Sb) in either the capping layer or into the dots is one example. However, these studies are normally focused on buried QD (BQD) where there are still different controversial theories concerning the role of Sb. Ones suggest that Sb incorporates into the dot [1], while others support the hypothesis that the Sb occupies positions surrounding the dot [2] thus helping to keep their shape during the capping growth.

Room temperature photoluminescence of InGaAs Surface Quantum Dots

Self-assembled InGaAs quantum dots show unique physical properties such as three dimensional confinement, high size homogeneity, high density and low number of dislocations. They have been extensively used in the active regions of laser devices for optical communications applications [1]. Therefore, buried quantum dots (BQDs) embedded in wider band gap materials have been normally studied. The wave confinement in all directions and the stress field around the dot affect both optical and electrical properties [2, 3]. However, surface quantum dots (SQDs) are less affected by stress, although their optical and electrical characteristics have a strong dependence on surface fluctuation. Thus, they can play an important role in sensor applications

Epidemiological characteristics and diagnostic approach in patients admitted to the emergency room for transient loos of consciousness: Group for Syncope Study in the Emergency Room (GESINUR) study

Aims: To assess the clinical presentation and acute management of patients with transient loss of consciousness (T-LOC) in the emergency department (ED). Methods and results: A multi-centre prospective observational study was carried out in 19 Spanish hospitals over 1 month. The patients included were 14 years old and were admitted to the ED because of an episode of T-LOC. Questionnaires and corresponding electrocardiograms (ECGs) were reviewed by a Steering Committee (SC) to unify diagnostic criteria, evaluate adherence to guidelines, and diagnose correctly the ECGs. We included 1419 patients (prevalence, 1.14%).ECG was performed in 1335 patients (94%) in the ED: 498 (37.3%) ECGs were classified as abnormal. The positive diagnostic yield ranged from 0% for the chest X-ray to 12% for the orthostatic test. In the ED, 1217 (86%) patients received a final diagnosis of syncope, whereas the remaining 202 (14%) were diagnosed of non-syncopal transient lossof consciousness (NST-LOC). After final review by the SC, 1080 patients (76%) were diagnosed of syncope, whereas 339 (24%) were diagnosed of NST-LOC (P , 0.001). Syncope was diagnosed correctly in 84% of patients. Only 25% of patients with T-LOC were admitted to hospitals. Conclusion Adherence to clinical guidelines for syncope management was low; many diagnostic tests were performed with low diagnostic yield. Important differences were observed between syncope diagnoses at the ED and by SC decision.

Rectangular room dimensions estimation using narrowband signal and sectorized antennas

A system for estimation of unknown rectangular room dimensions based on two radio transceivers, both capable of full duplex operations, is presented. The approach is based on CIR measurements taken at the same place where the signal is transmitted (generated), commonly known as self- to-self CIR. Another novelty is the receiver antenna design which consists of eight sectorized antennas with 45° aperture in the horizontal plane, whose total coverage corresponds to the isotropic one. The dimensions of a rectangular room are reconstructed directly from radio impulse responses by extracting the information regarding features like round trip time, received signal strength and reverberation time. Using radar approach the estimation of walls and corners positions are derived. Additionally, the analysis of the absorption coefficient of the test environment is conducted and a typical coefficient for office room with furniture is proposed. Its accuracy is confirmed through the results of volume estimation. Tests using measured data were performed, and the simulation results confirm the feasibility of the approach.

Scale model research for room acoustics purposes

In the field of Room Acoustics it is common using scale models to study a room. Through this method it is possible to predict its behavior, which may be very useful to detect and correct any problem prior to build it, saving many resources. Nowadays this method has been relegated to a secondary position due to the peak of simulation software, which makes possible studying rooms in a cheap, flexible and simple way, as well as it is potentially less time consuming. Nevertheless, the scale model method is still under study, as it may give some additional information. This project intends to focus in pedagogic possibilities of the scale model method. This method offers the student the opportunity of study and grasp some of the most important phenomena in Room Acoustics, in a more intuitive way than just a software simulation. Furthermore most of the existing software in this field is aimed to the technician working in the lab, as efficiently as possible, not to the student trying to understand and learn something. Here, the facilities and resources of Syddansk Universitet regarding this matter will be studied and evaluated, as well as the procedure for the experiments, paying special attention not only to its reliability and accuracy, but also to its didactic possibilities. Besides, if possible, any improvement that could help to enhance any of the listed aspects will be suggested. En el ámbito de la Acústica Arquitectónica es común el uso de modelos a escala para estudiar un recinto determinado. Mediante esta técnica es posible por ejemplo predecir el comportamiento del recinto y detectar problemas antes de su construcción, con el consecuente ahorro de recursos. Actualmente el uso de modelos a escala está desplazado a un segundo plano por el uso de software simulación, debido a la sencillez y flexibilidad que puede aportar la simulación por ordenador, así como a la economía de tiempo y recursos que supone. Sin embargo sigue siendo objeto de estudio, dado que puede aportar información muy valiosa para el ingeniero. Este proyecto se centra en las posibilidades pedagógicas de dicho método. El uso de modelos a escala brinda la oportunidad a los estudiantes de estudiar y comprender algunos de los fenómenos más importantes en la Acústica Arquitectónica de una forma más directa e intuitiva que una simulación por ordenador. Se pretende estudiar y evaluar los medios al alcance de los estudiantes en la Syddansk Universitet, así como los métodos usados, atendiendo no sólo a su precisión y fiabilidad, si no a su potencial pedagógico. Así mismo, si es posible, se propondrán cambios que puedan suponer una mejora en cualquiera de estos aspectos. Así el proyecto se divide en varias secciones claramente diferenciadas. En el apartado Background and Theoretical Basis se introduce el tema del estudio y simulación de recintos acústicos. Se explica su importancia y utilidad, y se comenta la situación actual de estas técnicas, abordando diferentes métodos usados así como sus bases teóricas y principales ventajas e inconvenientes. Bajo el apartado de Project se analizan diferentes factores relacionados con el problema. Se estudian los recursos a disposición del alumno, desde el software y hardware implicados hasta el equipo de medida y otros recursos necesarios para la realización de las prácticas. Es en esta parte donde se centra la parte más importante del trabajo, consistente en la medición y comprobación de las características más relevantes del equipo implicado. Haciendo posible así confirmar su validez y precisión, tanto desde el punto de vista técnico como pedagógico, así como estableciendo los límites dentro de los que se puede considerar fiable el modelo. Al final de este apartado se aborda la influencia de la absorción del aire en altas frecuencias, y la variación en los coeficientes de absorción y dispersión de los materiales respecto de la frecuencia. Por último se realiza una verificación subjetiva del sistema completo, debido a que por limitaciones técnicas no ha sido posible evaluar el montaje en el rango equivalente a toda la banda audible, y que los métodos estudiados tienen como meta última asegurar una buena percepción por parte del oyente en el recinto dado. Dentro del apartado Conclusions se hace un breve resumen de las conclusiones extraídas anteriormente, y se valora el rendimiento y utilidad general del modelo, que a pesar de algunos problemas de precisión y repetibilidad lógicos debido a los medios usados, es válido para ilustrar los fenómenos físicos que se quieren enseñar al alumno. En la sección de Future Work se proponen diferentes vías de trabajo para futuros proyectos en la Syddansk Universitet que podrían ser útiles confirmar el trabajo realizado en este proyecto, mejorar la precisión y fiabilidad del montaje o enriquecer las posibilidades pedagógicas de las prácticas relacionadas. Por último se encuentra, tras el apartado de referencias, los anexos con tablas y gráficas relativas a las medidas realizadas en diferentes partes del trabajo. También se puede encontrar información y material relacionado con el proyecto en el CD adjunto.

Estudios termodinámicos de los procesos de vitrificación en la crioconservación de germoplasma vegetal=Thermodynamic studies of vitrification processes in plant germplasm cryopreservation

En la actualidad, las técnicas de crioconservación poseen una importancia creciente para el almacenamiento a largo plazo de germoplasma vegetal. En las dos últimas décadas, estos métodos experimentaron un gran desarrollo y se han elaborado protocolos adecuados a diferentes sistemas vegetales, utilizando diversas estrategias como la vitrificación, la encapsulación-desecación con cuentas de alginato y el método de “droplet”-vitrificación. La presente tesis doctoral tiene como objetivo aumentar el conocimiento sobre los procesos implicados en los distintos pasos de un protocolo de crioconservación, en relación con el estado del agua presente en los tejidos y sus cambios, abordado mediante diversas técnicas biofísicas, principalmente calorimetría diferencial de barrido (DSC) y microscopía electrónica de barrido a baja temperatura (crio-SEM). En un primer estudio sobre estos métodos de crioconservación, se describen las fases de enfriamiento hasta la temperatura del nitrógeno líquido y de calentamiento hasta temperatura ambiente, al final del periodo de almacenamiento, que son críticas para la supervivencia del material crioconservado. Tanto enfriamiento como calentamiento deben ser realizados lo más rápidamente posible pues, aunque los bajos contenidos en agua logrados en etapas previas de los protocolos reducen significativamente las probabilidades de formación de hielo, éstas no son del todo nulas. En ese contexto, se analiza también la influencia de las velocidades de enfriamiento y calentamiento de las soluciones de crioconservación de plantas en sus parámetros termofísicos referente a la vitrificación, en relación su composición y concentración de compuestos. Estas soluciones son empleadas en la mayor parte de los protocolos actualmente utilizados para la crioconservación de material vegetal. Además, se estudia la influencia de otros factores que pueden determinar la estabilidad del material vitrificado, tales como en envejecimiento del vidrio. Se ha llevado a cabo una investigación experimental en el empleo del crio-SEM como una herramienta para visualizar el estado vítreo de las células y tejidos sometidos a los procesos de crioconservación. Se ha comparado con la más conocida técnica de calorimetría diferencial de barrido, obteniéndose resultados muy concordantes y complementarios. Se exploró también por estas técnicas el efecto sobre tejidos vegetales de la adaptación a bajas temperaturas y de la deshidratación inducida por los diferentes tratamientos utilizados en los protocolos. Este estudio permite observar la evolución biofísica de los sistemas en el proceso de crioconservación. Por último, se estudió la aplicación de películas de quitosano en las cuentas de alginato utilizadas en el protocolo de encapsulación. No se observaron cambios significativos en su comportamiento frente a la deshidratación, en sus parámetros calorimétricos y en la superficie de las cuentas. Su aplicación puede conferir propiedades adicionales prometedoras. ABSTRACT Currently, cryopreservation techniques have a growing importance for long term plant germplasm storage. These methods have undergone great progress during the last two decades, and adequate protocols for different plant systems have been developed, making use of diverse strategies, such as vitrification, encapsulation-dehydration with alginate beads and the dropletvitrification method. This PhD thesis has the goal of increasing the knowledge on the processes underlying the different steps of cryopreservation protocols, in relation with the state of water on tissues and its changes, approached through diverse biophysical techniques, especially differential scanning calorimetry (DSC) and low-temperature scanning electron microscopy (cryo-SEM). The processes of cooling to liquid nitrogen temperature and warming to room temperature, at the end of the storage period, critical for the survival of the cryopreserved material, are described in a first study on these cryopreservation methods. Both cooling and warming must be carried out as quickly as possible because, although the low water content achieved during previous protocol steps significantly reduces ice formation probability, it does not completely disappear. Within this context, the influence of plant vitrification solutions cooling and warming rate on their vitrification related thermophysical parameters is also analyzed, in relation to its composition and component concentration. These solutions are used in most of the currently employed plant material cryopreservation protocols. Additionally, the influence of other factors determining the stability of vitrified material is studied, such as glass aging. An experimental research work has been carried out on the use of cryo-SEM as a tool for visualizing the glassy state in cells and tissues, submitted to cryopreservation processes. It has been compared with the better known differential scanning calorimetry technique, and results in good agreement and complementary have been obtained. The effect on plant tissues of adaptation to low temperature and of the dehydration induced by the different treatments used in the protocols was explored also by these techniques. This study allows observation of the system biophysical evolution in the cryopreservation process. Lastly, the potential use of an additional chitosan film over the alginate beads used in encapsulation protocols was examined. No significant changes could be observed in its dehydration and calorimetric behavior, as well as in its surface aspect; its application for conferring additional properties to gel beads is promising.

Optimization methods for the operating room management under uncertainty: stochastic programming vs. decomposition approach

The operating theatres are the engine of the hospitals; proper management of the operating rooms and its staff represents a great challenge for managers and its results impact directly in the budget of the hospital. This work presents a MILP model for the efficient schedule of multiple surgeries in Operating Rooms (ORs) during a working day. This model considers multiple surgeons and ORs and different types of surgeries. Stochastic strategies are also implemented for taking into account the uncertain in surgery durations (pre-incision, incision, post-incision times). In addition, a heuristic-based methods and a MILP decomposition approach is proposed for solving large-scale ORs scheduling problems in computational efficient way. All these computer-aided strategies has been implemented in AIMMS, as an advanced modeling and optimization software, developing a user friendly solution tool for the operating room management under uncertainty.

Demonstration of the operation principles of intermediate band solar cells at room temperature

In this work we report, for the first time at room temperature, experimental results that prove, simultaneously in the same device, the two main physical principles involved in the operation of intermediate band solar cells: (1) the production of sub-bandgap photocurrent by two optical transitions through the intermediate band; (2) the generation of an output voltage which is not limited by the photon energy absorption threshold. These principles, which had always required cryogenic temperatures to be evidenced all together, are now demonstrated at room temperature on an intermediate band solar cell based on InAs quantum dots with Al0.3Ga0.7As barriers.