An experimental and theoretical study of unsteady flow (gust) effects on structures

The gust wind tunnel at IDR, Universidad Politécnica de Madrid (UPM), has been enhanced and the impact of the modification has been characterized. Several flow quality configurations have been tested. The problems in measuring gusty winds with Pitot tubes have been considered. Experimental results have been obtained and compared with theoretically calculated results (based on potential flow theory). A theoretical correction term has been proposed for unsteady flow measurements obtained with Pitot tubes. The effect of unsteady flow on structures and laying bodies on the ground has been also considered. A theoretical model has been proposed for a semi-circular cylinder and experimental tests have been performed to study the unsteady flow effects, which can help in clarifying the phenomenon.

Gust wind tunnel study on ballast pick-up by high-speed trains

This paper describes the experimental setup, procedure, and results obtained, concerning the dynamics of a body lying on a floor, attached to a hinge, and exposed to an unsteady flow, which is a model of the initiation of rotational motion of ballast stones due to the wind generated by the passing of a high-speed train. The idea is to obtain experimental data to support the theoretical model developed in Sanz-Andres and Navarro-Medina (J Wind Eng Ind Aerodyn 98, 772–783, (2010), aimed at analyzing the initial phase of the ballast train-induced-wind erosion (BATIWE) phenomenon. The experimental setup is based on an open circuit, closed test section, low-speed wind tunnel, with a new sinusoidal gust generator mechanism concept, designed and built at the IDR/UPM. The tunnel’s main characteristic is the ability to generate a flow with a uniform velocity profile and sinusoidal time fluctuation of the speed. Experimental results and theoretical model predictions are in good agreement.

The Dynamics of High-Speed Railway Bridges: A Review of Design Issues and New Research for Lateral Dynamics

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for the consideration of safe running conditions for the trains. In this work we start by reviewing the relevance of some basic design aspects. The significance of impact factor envelopes for moving loads is considered first. Resonance which may be achieved for high-speed trains requires dynamic analysis, for which some key aspects are discussed. The relevance of performing a longitudinal distribution of axle loads, the number of modes taken in analysis, and the consideration of vehicle-structure interaction are discussed with representative examples. The lateral dynamic effects of running trains on bridges is of importance for laterally compliant viaducts, such as some very tall structures erected in new high-speed lines. The relevance of this study is mainly for the safety of the traffic, considering both internal actions such as the hunting motion as well as external actions such as wind or earthquakes [1]. These studies require three-dimensional dynamic coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework [2]. The wheel-rail contact has been considered using a FastSim algorithm which provides a compromise between accuracy and computational cost, and captures the main nonlinear response of the contact interface. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the dynamic interaction between bridge and vehicle. The second application is to a real HS viaduct with a long continuous deck and tall piers and high lateral compliance [3]. The results show the safety of the traffic as well as the importance of considering features such as track alignment irregularities.

Criteria for Ballast Flight Initiation Induced by High Speed Trains

One of the phenomena that limit the velocity of trains in high speed lines is the so- called “ballast pick-up”. It is a ballast train-induced-wind erosion (or BATIWE) that can produce damage to the train under body and the infrastructure surrounding the tracks. The analysis of the measurements taken during several passes of the train allows for a criterion of ballast flight initiation to be obtained. The first rotation of a ballast stone occurs when the impulse given to the stone (arising from the aerodynamic loading produced by the wind gust genera ted by the passing train) overpasses a critical impulse. This impulse depends on the physical properties of the stone (mass, shape, moment of inertia, etc. ...) and its posture on the track bed. The aim of this paper is to report on the experimental results obtained in the ADIF’S Brihuega (Guadalajara) test station, in the Madrid to Barcelona high speed line, and the way they can be used to support the feasibility of the definition of a criterion to evaluate the BA TIWE capability of trains. The results obtained show the feasibility of the proposed method, and contribute to a method of BATIWE characterization, which can be relevant for the development of train interoperability standardization.

Analysis of lateral dynamics of railway vehicles on viaducts with coupled models

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a br idge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle. The second application is to a real viaduct in a high-speed line, with a long continuous deck and tall piers with high lateral compliance. The results show the safety of the traffic as well as the relevance of considering the wind action and the nonlinear response.

Coupled models for the dynamics of bridges under high-speed rail traffic

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for determining safe running conditions of trains. In this work we start by reviewing the relevance of some basic moving load models for the dynamic action of vertical traffic loads. The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models and consideration of wheel to rail contact. We describe here a fully nonlinear coupled model, formulated in absolute coordinates and incorporated into a commercial finite element framework. An application example is presented for a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Aerodynamic loads on bluff bodies under wind gusts

Esta tesis doctoral se ha centrado en el estudio de las cargas aerodinámicas no estacionario en romos cuerpos o no aerodinámicos (bluff bodies). Con este objetivo se han identificado y analizado los siguientes puntos: -Caracterización del flujo medido con diferentes tipos de tubos de Pitot y anemómetro de hilo caliente en condiciones de flujo no estacionario inestable generado por un túnel aerodinamico de ráfagas. -Diseño e integración de los montajes experimentales requeridos para medir las cargas de viento internas y externas que actúan sobre los cuerpos romos en condiciones de flujo de viento con ráfagas. -Implementación de modelos matemáticos semi-empíricos basados en flujo potencial y las teorías fenomenológicas pertinentes para simular los resultados experimentales. -En diversan condiciones de flujo con ráfagas, la identificación y el análisis de la influencia de los parámetros obtenida a partir de los modelos teóricos desarrollados. -Se proponen estimaciones empíricas para averiguar los valores adecuados de los parámetros que influyente, mediante el ajuste de los resultados experimentales y los predichos teóricamente. Los montajes experimentales se has reakizado en un tunel aerodinamico de circuito abierto, provisto de baja velocidad, cámara de ensayes cerrada, un nuevo concepto de mecanismo generador de ráfaga sinusoidal, diseñado y construido en el Instituto de Microgravedad "Ignacio Da Riva" de la Universidad Politécnica de Madrid, (IDR / UPM). La principal característica de este túnel aerodynamico es la capacidad de generar un flujo con un perfil de velocidad uniforme y una fluctuación sinusoidal en el tiempo. Se han realizado pruebas experimentales para estudiar el efecto de los flujos no estacionarios en cuerpos romos situados en el suelo. Se han propuesto dos modelos teóricos para diterminar las cargas de presión externas e internas respectivamente. Con el fin de satisfacer la necesidad de la crea ráfagas de viento sinusoidales para comprobar las predicciones de los modelos teóricos, se han obtenido velocidades de hasta 30 m/s y frecuencias ráfaga de hasta 10 Hz. La sección de la cámara de ensayos es de 0,39 m x 0,54 m, dimensiónes adecuadas para llevar a cabo experimentos con modelos de ensayos. Se muestra que en la gama de parámetros explorados los resultados experimentales están en buen acuerdo con las predicciones de los modelos teóricos. Se han realizado pruebas experimentales para estudiar los efectos del flujo no estacionario, las cuales pueden ayudar a aclarar el fenómeno de las cargas de presión externa sobre los cuerpos romos sometidos a ráfagas de viento: y tambien para determinan las cargas de presión interna, que dependen del tamaño de los orificios de ventilación de la construcción. Por último, se ha analizado la contribución de los términos provenientes del flujo no estacionario, y se han caracterizado o los saltos de presión debido a la pérdida no estacionario de presión a través de los orificios de ventilación. ABSTRACT This Doctoral dissertation has been focused to study the unsteady aerodynamic loads on bluff bodies. To this aim the following points have been identified and analyzed: -Characterization of the flow measured with different types of Pitot tubes and hot wire anemometer at unsteady flow conditions generated by a gust wind tunnel. -Design and integrating of the experimental setups required to measure the internal and external wind loads acting on bluff bodies at gusty wind flow conditions. -Implementation of semi-empirical mathematical models based on potential flow and relevant phenomenological theories to simulate the experimental results.-At various gusty flow conditions, extracting and analyzing the influence of parameters obtained from the developed theoretical models. -Empirical estimations are proposed to find out suitable values of the influencing parameters, by fitting the experimental and theoretically predicted results. The experimental setups are performed in an open circuit, closed test section, low speed wind tunnel, with a new sinusoidal gust generator mechanism concept, designed and built at the Instituto de Microgravedad “Ignacio Da Riva” of the Universidad Politécnica de Madrid, (IDR/UPM). The main characteristic of this wind tunnel is the ability to generate a flow with a uniform velocity profile and a sinusoidal time fluctuation of the speed. Experimental tests have been devoted to study the effect of unsteady flows on bluff bodies lying on the ground. Two theoretical models have been proposed to measure the external and internal pressure loads respectively. In order to meet the need of creating sinusoidal wind gusts to check the theoretical model predictions, the gust wind tunnel maximum flow speed and, gust frequency in the test section have been limited to 30 m/s and 10 Hz, respectively have been obtained. The test section is 0.39 m × 0.54 m, which is suitable to perform experiments with testing models. It is shown that, in the range of parameters explored, the experimental results are in good agreement with the theoretical model predictions. Experimental tests have been performed to study the unsteady flow effects, which can help in clarifying the phenomenon of the external pressure loads on bluff bodies under gusty winds: and also to study internal pressure loads, which depend on the size of the venting holes of the building. Finally, the contribution of the unsteady flow terms in the theoretical model has been analyzed, and the pressure jumps due to the unsteady pressure losses through the venting holes have been characterized.

Aerodynamic external pressure loads on a semi-circular bluff body under wind gusts

This brief communication concerns the unsteady aerodynamic external pressure loads acting on a semi-circular bluff body lying on a floor under wind gusts and describes the theoretical model, experimental setup, and experimental results obtained. The experimental setup is based on an open circuit, closed test section, low speed wind tunnel, which includes a sinusoidal gust generating mechanism, designed and built at the Instituto de Microgravedad “Ignacio Da Riva” of the Universidad Politécnica de Madrid (IDR/UPM). Based on the potential flow theory, a theoretical model has been proposed to analyse the problem, and experimental tests have been performed to study the unsteady aerodynamic loads on a semi-circular bluff body. By fitting the theoretical model predictions with the experimental results, influencing parameters of the unsteady aerodynamic loads are ascertained. The values of these parameters can help in clarifying the phenomenon of the external pressure loads on semi-circular bluff body under various gust frequencies. The theoretical model proposed allows the pressure variation to be split into two contributions, a quasi-steady term and an unsteady term with a simple physical meaning

Método computacional para la aceleración de análisis paramétricos de modificaciones locales en estructuras complejas sometidas a cargas dinámicas

Dentro del análisis y diseño estructural surgen frecuentemente problemas de ingeniería donde se requiere el análisis dinámico de grandes modelos de elementos finitos que llegan a millones de grados de libertad y emplean volúmenes de datos de gran tamaño. La complejidad y dimensión de los análisis se dispara cuando se requiere realizar análisis paramétricos. Este problema se ha abordado tradicionalmente desde diversas perspectivas: en primer lugar, aumentando la capacidad tanto de cálculo como de memoria de los sistemas informáticos empleados en los análisis. En segundo lugar, se pueden simplificar los análisis paramétricos reduciendo su número o detalle y por último se puede recurrir a métodos complementarios a los elementos .nitos para la reducción de sus variables y la simplificación de su ejecución manteniendo los resultados obtenidos próximos al comportamiento real de la estructura. Se propone el empleo de un método de reducción que encaja en la tercera de las opciones y consiste en un análisis simplificado que proporciona una solución para la respuesta dinámica de una estructura en el subespacio modal complejo empleando un volumen de datos muy reducido. De este modo se pueden realizar análisis paramétricos variando múltiples parámetros, para obtener una solución muy aproximada al objetivo buscado. Se propone no solo la variación de propiedades locales de masa, rigidez y amortiguamiento sino la adición de grados de libertad a la estructura original para el cálculo de la respuesta tanto permanente como transitoria. Adicionalmente, su facilidad de implementación permite un control exhaustivo sobre las variables del problema y la implementación de mejoras como diferentes formas de obtención de los autovalores o la eliminación de las limitaciones de amortiguamiento en la estructura original. El objetivo del método se puede considerar similar a los que se obtienen al aplicar el método de Guyan u otras técnicas de reducción de modelos empleados en dinámica estructural. Sin embargo, aunque el método permite ser empleado en conjunción con otros para obtener las ventajas de ambos, el presente procedimiento no realiza la condensación del sistema de ecuaciones, sino que emplea la información del sistema de ecuaciones completa estudiando tan solo la respuesta en las variables apropiadas de los puntos de interés para el analista. Dicho interés puede surgir de la necesidad de obtener la respuesta de las grandes estructuras en unos puntos determinados o de la necesidad de modificar la estructura en zonas determinadas para cambiar su comportamiento (respuesta en aceleraciones, velocidades o desplazamientos) ante cargas dinámicas. Por lo tanto, el procedimiento está particularmente indicado para la selección del valor óptimo de varios parámetros en grandes estructuras (del orden de cientos de miles de modos) como pueden ser la localización de elementos introducidos, rigideces, masas o valores de amortiguamientos viscosos en estudios previos en los que diversas soluciones son planteadas y optimizadas, y que en el caso de grandes estructuras, pueden conllevar un número de simulaciones extremadamente elevado para alcanzar la solución óptima. Tras plantear las herramientas necesarias y desarrollar el procedimiento, se propone un caso de estudio para su aplicación al modelo de elementos .nitos del UAV MILANO desarrollado por el Instituto Nacional de Técnica Aeroespacial. A dicha estructura se le imponen ciertos requisitos al incorporar un equipo en aceleraciones en punta de ala izquierda y desplazamientos en punta de ala derecha en presencia de la sustentación producida por una ráfaga continua de viento de forma sinusoidal. La modificación propuesta consiste en la adición de un equipo en la punta de ala izquierda, bien mediante un anclaje rígido, bien unido mediante un sistema de reducción de la respuesta dinámica con propiedades de masa, rigidez y amortiguamiento variables. El estudio de los resultados obtenidos permite determinar la optimización de los parámetros del sistema de atenuación por medio de múltiples análisis dinámicos de forma que se cumplan de la mejor forma posible los requisitos impuestos con la modificación. Se comparan los resultados con los obtenidos mediante el uso de un programa comercial de análisis por el método de los elementos .nitos lográndose soluciones muy aproximadas entre el modelo completo y el reducido. La influencia de diversos factores como son el amortiguamiento modal de la estructura original, el número de modos retenidos en la truncatura o la precisión proporcionada por el barrido en frecuencia se analiza en detalle para, por último, señalar la eficiencia en términos de tiempo y volumen de datos de computación que ofrece el método propuesto en comparación con otras aproximaciones. Por lo tanto, puede concluirse que el método propuesto se considera una opción útil y eficiente para el análisis paramétrico de modificaciones locales en grandes estructuras. ABSTRACT When developing structural design and analysis some projects require dynamic analysis of large finite element models with millions of degrees of freedom which use large size data .les. The analysis complexity and size grow if a parametric analysis is required. This problem has been approached traditionally in several ways: one way is increasing the power and the storage capacity of computer systems involved in the analysis. Other obvious way is reducing the total amount of analyses and their details. Finally, complementary methods to finite element analysis can also be employed in order to limit the number of variables and to reduce the execution time keeping the results as close as possible to the actual behaviour of the structure. Following this third option, we propose a model reduction method that is based in a simplified analysis that supplies a solution for the dynamic response of the structure in the complex modal space using few data. Thereby, parametric analysis can be done varying multiple parameters so as to obtain a solution which complies with the desired objetive. We propose not only mass, stiffness and damping variations, but also addition of degrees of freedom to the original structure in order to calculate the transient and steady-state response. Additionally, the simple implementation of the procedure allows an in-depth control of the problem variables. Furthermore, improvements such as different ways to obtain eigenvectors or to remove damping limitations of the original structure are also possible. The purpose of the procedure is similar to that of using the Guyan or similar model order reduction techniques. However, in our method we do not perform a true model order reduction in the traditional sense. Furthermore, additional gains, which we do not explore herein, can be obtained through the combination of this method with traditional model-order reduction procedures. In our procedure we use the information of the whole system of equations is used but only those nodes of interest to the analyst are processed. That interest comes from the need to obtain the response of the structure at specific locations or from the need to modify the structure at some suitable positions in order to change its behaviour (acceleration, velocity or displacement response) under dynamic loads. Therefore, the procedure is particularly suitable for parametric optimization in large structures with >100000 normal modes such as position of new elements, stiffness, mass and viscous dampings in previous studies where different solutions are devised and optimized, and in the case of large structures, can carry an extremely high number of simulations to get the optimum solution. After the introduction of the required tools and the development of the procedure, a study case is proposed with use the finite element model (FEM) of the MILANO UAV developed by Instituto Nacional de Técnica Aeroespacial. Due to an equipment addition, certain acceleration and displacement requirements on left wing tip and right wing tip, respectively, are imposed. The structure is under a continuous sinusoidal wind gust which produces lift. The proposed modification consists of the addition of an equipment in left wing tip clamped through a rigid attachment or through a dynamic response reduction system with variable properties of mass, stiffness and damping. The analysis of the obtained results allows us to determine the optimized parametric by means of multiple dynamic analyses in a way such that the imposed requirements have been accomplished in the best possible way. The results achieved are compared with results from a commercial finite element analysis software, showing a good correlation. Influence of several factors such as the modal damping of the original structure, the number of modes kept in the modal truncation or the precission given by the frequency sweep is analyzed. Finally, the efficiency of the proposed method is addressed in tems of computational time and data size compared with other approaches. From the analyses performed, we can conclude that the proposed method is a useful and efficient option to perform parametric analysis of possible local modifications in large structures.

Comparative study of the effect of several trains on the ballast rotation

The ballast pick-up (or ballast train-induced-wind erosion (BTE)) phenomenon is a limiting factor for the maximum allowed operational train speed. The determination of the conditions for the initiation of the motion of the ballast stones due to the wind gust created by high-speed trains is critical to predict the start of ballast pick-up because, once the motion is initiated, a saltation-like chain reaction can take place. The aim of this paper is to present a model to evaluate the effect of a random aerodynamic impulse on stone motion initiation, and an experimental study performed to check the capability of the proposed model to classify trains by their effect on the ballast due to the flow generated by the trains. A measurement study has been performed at kp 69 + 500 on the Madrid – Barcelona High Speed Line. The obtained results show the feasibility of the proposed method, and contribute to a technique for BTE characterization, which can be relevant for the development of train interoperability standards

Pedestrian wind comfort: feasibility study of criteria homogenisation

One of the aims of COST C14 action is the assessment and evaluation of pedestrian wind comfort. At present there is no general rule available that is applied across Europe. There are several criteria that have been developed and applied in different countries. These criteria are based on the definition of two independent parameters, a threshold effective wind speed and a probability of exceedence of this threshold speed. The difficulty of the criteria comparison arises from the two-dimensional character of the criteria definition. An effort is being made to compare these criteria, trying both to find commonalities and to clearly identify differences, in order to build up the basis for the next step: to try to define common criteria (perhaps with regional and seasonal variations). The first point is to define clearly the threshold effective wind speed (mean velocity definition parameters: averaging interval and reference height) and equivalence between different ways of defining the threshold effective wind speed (mean wind speed, gust equivalent mean, etc.) in comparable terms (as far as possible). It can be shown that if the wind speed at a given location is defined in terms of a probability distribution, e.g. Weibull function, a given criterion is satisfied by an infinite set of wind conditions, that is, of probability distributions. The criterion parameters and the Weibull function parameters are linked to each other, establishing a set called iso-criteria lines (the locus of the Weibull function parameters that fulfil a given criterion). The relative position of iso-criteria lines when displayed in a suitable two-dimensional plane facilitates the comparison of comfort criteria. The comparison of several wind comfort criteria, coming from several institutes is performed, showing the feasibility and limitations of the method.