Spatial analysis of geometric design consistency and road sight distance

Because of the high number of crashes occurring on highways, it is necessary to intensify the search for new tools that help in understanding their causes. This research explores the use of a geographic information system (GIS) for an integrated analysis, taking into account two accident-related factors: design consistency (DC) (based on vehicle speed) and available sight distance (ASD) (based on visibility). Both factors require specific GIS software add-ins, which are explained. Digital terrain models (DTMs), vehicle paths, road centerlines, a speed prediction model, and crash data are integrated in the GIS. The usefulness of this approach has been assessed through a study of more than 500 crashes. From a regularly spaced grid, the terrain (bare ground) has been modeled through a triangulated irregular network (TIN). The length of the roads analyzed is greater than 100 km. Results have shown that DC and ASD could be related to crashes in approximately 4% of cases. In order to illustrate the potential of GIS, two crashes are fully analyzed: a car rollover after running off road on the right side and a rear-end collision of two moving vehicles. Although this procedure uses two software add-ins that are available only for ArcGIS, the study gives a practical demonstration of the suitability of GIS for conducting integrated studies of road safety.

Metodología para la evaluación de la consistencia del trazado de carreteras interurbanas de dos carriles

La consistencia del trazado puede interpretarse como la relación entre las características geométricas de una carretera y lo que espera encontrar el conductor que circula por ella. Si hay una correspondencia entre estos dos aspectos, la conducción puede hacerse de modo continuo, sin sobresaltos, lo que incide favorablemente sobre la seguridad en la circulación. Si bien hay una serie de recomendaciones desde el punto de vista geométrico para obtener trazados consistentes, esto no siempre se logra, y sólo en los últimos años se ha iniciado el estudio de metodologías para evaluar ésto, tanto en vías existentes como en vías proyectadas. La mayor parte de estas metodologías sólo considera el trazado en planta, olvidándose del trazado en alzado y de la coordinación entre los mismos. En esta Tesis doctoral se ha desarrollado una metodología para evaluar la consistencia del trazado en carreteras interurbanas de dos carriles que considera dichos aspectos. Para ello, se hizo un análisis exhaustivo de los índices de trazado, los cuales evalúan las características geométricas en planta y en alzado. Los índices se correlacionaron con la accidentalidad, para determinar cuál de ellos tiene mayor incidencia, encontrándose que es el cambio de curvatura vertical (VCCR); a este índice se le estableció un rango de calificación. Como elemento de evaluación complementario de análisis se seleccionó el perfil de velocidades de operación, procedimiento que ha sido probado en diferentes investigaciones, y del cual se desarrolló un modelo aplicado a Colombia. Para la coordinación de trazados en planta y alzado se evaluaron diferentes combinaciones geométricas, algunas de las cuales generaron reapariciones del trazado. Se ha definido un nuevo índice (Irt) que permite determinar numéricamente la posibilidad de que se presente esta situación, indeseable desde el punto de vista de la seguridad vial. La combinación de estos tres elementos permite una evaluación integral de los diferentes aspectos que inciden sobre la consistencia del trazado de una carretera. La metodología desarrollada se aplicó en el estudio de consistencia del trazado en algunas carreteras españolas y colombianas, ubicadas en distintos tipos de terreno. ABSTRACT Geometric Design Consistency can be defined as the relationship between the geometric characteristics of a road and what the driver expects to find when driving. If there is a correspondence between these two aspects, driving is smoother and unexpected events are minimized, which increases traffic safety conditions. Although from the geometric point of view there are several recommendations to ensure consistent designs, this is not always successfully applied. The study of methods to evaluate design consistency in existing and future routes has only begun in recent years. Most existing methods only consider the horizontal alignment of the road and overlook both the vertical alignment and the coordination that must exist between the vertical and the horizontal. The present Doctoral Thesis proposes a method to evaluate the geometric design consistency of a two-lane rural highway which considers all three of these aspects: the horizontal alignment, the vertical alignment and the coordination that must exist between them. In order to achieve this, several different alignment indices, that evaluate horizontal and vertical geometric characteristics, were thoroughly analyzed to determine their correlation with traffic accidents. The Vertical Curvature Change Rate (VCCR) index showed the highest correlation, and rating thresholds for this index have been established. To complement the evaluation, the operating speed profile, was chosen. This procedure has been extensively tested by several researchers. An operating speed prediction model adapted to Colombia was developed. To study the coordination between the horizontal and the vertical alignments of the road, several geometric combinations of the two were used. Some of these combinations generate undesirable losses of visibility. For this reason, a new index (Irt) was defined to numerically detect those cases, which are undesirable from the point of view of traffic safety. The combination of these three factors allows a comprehensive evaluation of the different aspects that affect the geometric design consistency of a highway. The methodology was applied to some Spanish and Colombian roads located in different types of terrain.

Implementación de algoritmos para la manipulación de curvas concoides en diseño geométrico

Este proyecto se enmarca dentro de la Computación Simbólica y de los fundamentos matemáticos del Diseño Geométrico Asistido por ordenador (CAGD). Se abordara uno de los problemas principales en el ámbito del CAGD y que es la manipulación de las Curvas Concoide. La importancia del avance en la manipulación de las curvas concoide radica en el papel fundamental que desempeñan en múltiples aplicaciones en la actualidad dentro de campos de diversa índole tales como la medicina, la óptica, el electromagnetismo, la construcción, etc. El objetivo principal de este proyecto es el diseño e implementación de algoritmos para el estudio, cálculo y manipulación de curvas concoides, utilizando técnicas propias del Calculo Simbólico. Esta implementación se ha programado utilizando el sistema de computación simbólica Maple. El proyecto consiste en dos partes bien diferenciadas, una parte teórica y otra más practica. La primera incluye la descripción geométrica y definición formal de curvas concoide, así como las ideas y propiedades básicas. De forma más precisa, se presenta un estudio matemático sobre el análisis de racionalidad de estas curvas, explicando los algoritmos que serán implementados en las segunda parte, y que constituye el objetivo principal de este proyecto. Para cerrar esta parte, se presenta una pequeña introducción al sistema y a la programación en Maple. Por otro lado, la segunda parte de este proyecto es totalmente original, y en ella el autor desarrolla las implementaciones en Maple de los algoritmos presentados en la parte anterior, así como la creación de un paquete Maple que las recoge. Por último, se crean las paginas de ayudas en el sistema Maple para la correcta utilización del paquete matemático anteriormente mencionado. Una vez terminada la parte de implementación, se aplican los algoritmos implementados a una colección de curvas clásicas conocidas, recogiendo los datos y resultados obtenidos en un atlas de curvas. Finalmente, se presenta una recopilación de las aplicaciones más destacadas en las que las concoides desempeñan un papel importante así como una breve reseña sobre las concoides de superficies, objeto de varios estudios en la actualidad y a los que se considera que el presente proyecto les puede resultar de gran utilidad. Abstract This project is set up in the framework of Symbolic Computation as well as in the implementation of algebraic-geometric problems that arise from Computer Aided Geometric Design (C.A.G.D.) applications. We address problems related to conchoid curves. The importance of these curves is the fundamental role that they play in current applications as medicine, optics, electromagnetism, construction, etc. The main goal of this project is to design and implement some algorithms to solve problems in studying, calculating and generating conchoid curves with symbolic computation techniques. For this purpose, we program our implementations in the symbolic system “Maple". The project consists of two differentiated parts, one more theoretical part and another part more practical. The first one includes the description of conchoid curves as well as the basic ideas about the concept and its basic properties. More precisely, we introduce in this part the mathematical analysis of the rationality of the conchoids, and we present the algorithms that will be implemented. Furthermore, the reader will be brie y introduced in Maple programming. On the other hand, the second part of this project is totally original. In this more practical part, the author presents the implemented algorithms and a Maple package that includes them, as well as their help pages. These implemented procedures will be check and illustrated with some classical and well known curves, collecting the main properties of the conchoid curves obtained in a brief atlas. Finally, a compilation of the most important applications where conchoids play a fundamental role, and a brief introduction to the conchoids of surfaces, subject of several studies today and where this project could be very useful, are presented.

Modelización y simulación numérica de sistemas geotérmicos planos

En el presente proyecto se estudiará la conveniencia de utilizar simulación numérica para evaluar, diseñar y mejorar el diseño de instalaciones geotérmicas planas. Para ello, se modelizará el conjunto de terreno y sistema geotérmico mediante el acoplamiento de un modelo tridimensional (terreno) y un modelo unidimensional, formado por la red de tubería geotérmica, que estará dispuesta en un plano cuya orientación dependerá de las aplicaciones. Para la simulación numérica se utilizará un software de análisis y resolución por elementos finitos tipo comercial. Finalmente, se definirán unos parámetros geométricos de diseño y, teniendo en cuenta las propiedades térmicas de cada material, se realizarán estudios paramétricos para determinar la influencia de cada grupo de parámetros. Ello requerirá la realización de cientos de simulaciones numéricas que permitirán optimizar el rendimiento de sistemas geotérmicos planos tanto horizontales (soleras), como verticales (muros pantalla). ABSTRACT In this project it is going to be studied the convenience of numerical simulation as to evaluate, design and improve the design of geothermal planar installations. With this purpose, the terrain and the geothermal system will be modeled by coupling a three-dimensional model (terrain) and a one-dimensional model formed by the geothermal piping network disposed in a plane with an orientation which will depend on the applications. For the numerical simulation commercial software of analyzing and resolving by finite elements will be used. Finally, geometric design parameters will be defined, and taking into account the thermal properties of each material, parametric studies will be performed to determine the influence of each group of parameters. This will require the completion of hundreds of numerical simulations which will enhance the performance of both horizontal (slabs) and vertical (diaphragm walls) geothermal systems.

Conchoid surfaces of spheres

The conchoid of a surface F with respect to given xed point O is roughly speaking the surface obtained by increasing the radius function with respect to O by a constant. This paper studies conchoid surfaces of spheres and shows that these surfaces admit rational parameterizations. Explicit parameterizations of these surfaces are constructed using the relations to pencils of quadrics in R3 and R4. Moreover we point to remarkable geometric properties of these surfaces and their construction.

Diseño de un modelo para la identificación y análisis de tramos de carreteras sin accidentes : una nueva visión de la seguridad vial

El planteamiento tradicional de análisis de la accidentalidad en carretera pasa por la consideración de herramientas paliativas, como son la identificación y gestión de los puntos negros o tramos de concentración de accidentes, o preventivas, como las auditorías e inspecciones de seguridad vial. En esta tesis doctoral se presenta un planteamiento complementario a estas herramientas, desde una perspectiva novedosa: la consideración de los tramos donde no se producen accidentes; son los denominados Tramos Blancos. La tesis persigue demostrar que existen determinados parámetros del diseño de las carreteras y del tráfico que, bajo características generales similares de las vías, tienen influencia en el hecho de que se produzcan o no accidentes, adicionalmente a la exposición al riesgo, como factor principal, y a otros factores. La propia definición de los Tramos Blancos, entendidos como tramos de carreteras de longitud representativa donde no se han producido accidentes con víctimas mortales o heridos graves durante un periodo largo de tiempo, garantiza que esta situación no se produzca como consecuencia de la aleatoriedad de los accidentes, sino que pudiera deberse a una confluencia específica de determinados parámetros de la geometría de la vía y del tráfico total y de vehículos pesados. Para el desarrollo de esta investigación se han considerado la red de autopistas de peaje y las carreteras convencionales de la Red del Estado de España, que supone un total de 17.000 kilómetros, y los datos de accidentes con víctimas mortales y heridos graves en el periodo 2006-2010, ambos incluidos, en estas redes (un total de 10.000 accidentes). La red viaria objeto de análisis supone el 65% de la longitud de la Red de Carreteras del Estado, por la que circula el 33% de su tráfico; en ella se produjeron en el año 2013 el 47% de los accidentes con víctimas y el 60% de las víctimas mortales de la Red de Carreteras del Estado. Durante la investigación se ha desarrollado una base de datos de 250.130 registros y más de 3.5 millones de datos en el caso de las autopistas de peaje de la Red de Carreteras del Estado y de 935.402 registros y más de 14 millones de datos en el caso de la red convencional del Estado analizada. Tanto las autopistas de peaje como las carreteras convencionales han sido clasificadas según sus características de tráfico, de manera que se valoren vías con nivel de exposición al riesgo similar. Para cada tipología de vía, se ha definido como longitud de referencia para que un tramo se considere Tramo Blanco la longitud igual al percentil 95 de las longitudes de tramos sin accidentes con heridos graves o víctimas mortales durante el periodo 2006-2010. En el caso de las autopistas de peaje, en la tipología que ha sido considerada para la definición del modelo, esta longitud de referencia se estableció en 14.5 kilómetros, mientras que en el caso de las carreteras convencionales, se estableció en 7.75 kilómetros. Para cada uno de los tipos de vía considerados se han construido una base de datos en la que se han incluido las variables de existencia o no de Tramo Blanco, así como las variables de tráfico (intensidad media diaria total, intensidad de vehículos pesados y porcentaje de vehículos pesados ), la velocidad media y las variables de geometría (número de carriles, ancho de carril, ancho de arcén derecho e izquierdo, ancho de calzada y plataforma, radio, peralte, pendiente y visibilidad directa e inversa en los casos disponibles); como variables adicionales, se han incluido el número de accidentes con víctimas, los fallecidos y heridos graves, índices de peligrosidad, índices de mortalidad y exposición al riesgo. Los trabajos desarrollados para explicar la presencia de Tramos Blancos en la red de autopistas de peaje han permitido establecer las diferencias entre los valores medios de las variables de tráfico y diseño geométrico en Tramos Blancos respecto a tramos no blancos y comprobar que estas diferencias son significativas. Así mismo, se ha podido calibrar un modelo de regresión logística que explica parcialmente la existencia de Tramos Blancos, para rangos de tráfico inferiores a 10.000 vehículos diarios y para tráficos entre 10.000 y 15.000 vehículos diarios. Para el primer grupo (menos de 10.000 vehículos al día), las variables que han demostrado tener una mayor influencia en la existencia de Tramo Blanco son la velocidad media de circulación, el ancho de carril, el ancho de arcén izquierdo y el porcentaje de vehículos pesados. Para el segundo grupo (entre 10.000 y 15.000 vehículos al día), las variables independientes más influyentes en la existencia de Tramo Blanco han sido la velocidad de circulación, el ancho de calzada y el porcentaje de vehículos pesados. En el caso de las carreteras convencionales, los diferentes análisis realizados no han permitido identificar un modelo que consiga una buena clasificación de los Tramos Blancos. Aun así, se puede afirmar que los valores medios de las variables de intensidad de tráfico, radio, visibilidad, peralte y pendiente presentan diferencias significativas en los Tramos Blancos respecto a los no blancos, que varían en función de la intensidad de tráfico. Los resultados obtenidos deben considerarse como la conclusión de un análisis preliminar, dado que existen otros parámetros, tanto de diseño de la vía como de la circulación, el entorno, el factor humano o el vehículo que podrían tener una influencia en el hecho que se analiza, y no se han considerado por no disponer de esta información. En esta misma línea, el análisis de las circunstancias que rodean al viaje que el usuario de la vía realiza, su tipología y motivación es una fuente de información de interés de la que no se tienen datos y que permitiría mejorar el análisis de accidentalidad en general, y en particular el de esta investigación. Adicionalmente, se reconocen limitaciones en el desarrollo de esta investigación, en las que sería preciso profundizar en el futuro, reconociendo así nuevas líneas de investigación de interés. The traditional approach to road accidents analysis has been based in the use of palliative tools, such as black spot (or road sections) identification and management, or preventive tools, such as road safety audits and inspections. This thesis shows a complementary approach to the existing tools, from a new perspective: the consideration of road sections where no accidents have occurred; these are the so-called White Road Sections. The aim of this thesis is to show that there are certain design parameters and traffic characteristics which, under similar circumstances for roads, have influence in the fact that accidents occur, in addition to the main factor, which is the risk exposure, and others. White Road Sections, defined as road sections of a representative length, where no fatal accidents or accidents involving serious injured have happened during a long period of time, should not be a product of randomness of accidents; on the contrary, they might be the consequence of a confluence of specific parameters of road geometry, traffic volumes and heavy vehicles traffic volumes. For this research, the toll motorway network and single-carriageway network of the Spanish National Road Network have been considered, which is a total of 17.000 kilometers; fatal accidents and those involving serious injured from the period 2006-2010 have been considered (a total number of 10.000 accidents). The road network covered means 65% of the total length of the National Road Network, which allocates 33% of traffic volume; 47% of accidents with victims and 60% of fatalities happened in these road networks during 2013. During the research, a database of 250.130 registers and more than 3.5 million data for toll motorways and 935.042 registers and more than 14 million data for single carriageways of the National Road Network was developed. Both toll motorways and single-carriageways have been classified according to their traffic characteristics, so that the analysis is performed over roads with similar risk exposure. For each road type, a reference length for White Road Section has been defined, as the 95 percentile of all road sections lengths without accidents (with fatalities or serious injured) for 2006-2010. For toll motorways, this reference length concluded to be 14.5 kilometers, while for single-carriageways, it was defined as 7.75 kilometers. A detailed database was developed for each type of road, including the variable “existence of White Road Section”, as well as variables of traffic (average daily traffic volume, heavy vehicles average daily traffic and percentage of heavy vehicles from the total traffic volume), average speed and geometry variables (number of lanes, width of lane, width of shoulders, carriageway width, platform width, radius, superelevation, slope and visibility); additional variables, such as number of accidents with victims, number of fatalities or serious injured, risk and fatality rates and risk exposure, have also been included. Research conducted for the explanation of the presence of White Road Sections in the toll motorway network have shown statistically significant differences in the average values of variables of traffic and geometric design in White Road Sections compared with other road sections. In addition, a binary logistic model for the partial explanation of the presence of White Road Sections was developed, for traffic volumes lower than 10.000 daily vehicles and for those running from 10.000 to 15.000 daily vehicles. For the first group, the most influent variables for the presence of White Road Sections were the average speed, width of lane, width of left shoulder and percentage of heavy vehicles. For the second group, the most influent variables were found to be average speed, carriageway width and percentage of heavy vehicles. For single-carriageways, the different analysis developed did not reach a proper model for the explanation of White Road Sections. However, it can be assumed that the average values of the variables of traffic volume, radius, visibility, superelevation and slope show significant differences in White Road Sections if compared with others, which also vary with traffic volumes. Results obtained should be considered as a conclusion of a preliminary analysis, as there are other parameters, not only design-related, but also regarding traffic, environment, human factor and vehicle which could have an influence in the fact under research, but this information has not been considered in the analysis, as it was not available. In parallel, the analysis of the circumstances around the trip, including its typology and motivation is an interesting source of information, from which data are not available; the availability of this information would be useful for the improvement of accident analysis, in general, and for this research work, in particular. In addition, there are some limitations in the development of the research work; it would be necessary to develop an in-depth analysis in the future, thus assuming new research lines of interest.

Calidad ambiental electromagnética : atenuación de las radiaciones electromagnéticas en los espacios habitados

La perspectiva del arquitecto en calidad ambiental, y salud en un contexto sostenible, se amplía al considerar las radiaciones electromagnéticas no ionizantes en el diseño arquitectónico. En ese sentido, además del confort higrotérmico, acústico, lumínico y de la calidad del aire, se podría considerar el confort electromagnético de un lugar. Dado que existe gran controversia en cuales han de ser los límites de exposición a radiaciones electromagnéticas no ionizantes, establezco como punto de referencia los valores límite más restrictivos, que son los recomendados por la norma SBM-2008, desarrollada por el Institut für Baubiologie & Oekologie Neubeuern (IBN)1. Se plantean como hipótesis que podemos modificar el entorno electromagnético con materiales de construcción y geometría; y que determinados trazados geométricos tienen la capacidad de reducir el impacto de los campos electromagnéticos sobre los organismos vivos. El objetivo consiste en demostrar experimentalmente que podemos trabajar sobre la calidad ambiental electromagnética de un espacio, a través de la elección de materiales de construcción y trazados geométricos, intentando demostrar que existe una relación causa - efecto entre ambos. La metodología plantea tres aproximaciones experimentales, cada una con un tipo de radiación electromagnética, pues se pretende abarcar las situaciones que comúnmente se pueden presentar en un entorno habitado, ya sea urbano o rural. La primera aproximación trata sobre las alteraciones del campo geomagnético natural (nT / m) provocadas por los materiales de construcción. Utilizo el geomagnetómetro BPM 2010, para realizar un ensayo con cuatro tipos de materiales de distinta procedencia: origen vegetal muy poco procesado (corcho aglomerado negro) y más procesado (OSB), origen derivado del petróleo (tablero rígido de poliuretano) y de origen mineral metálico (chapa minionda). De la lectura de los datos se observa relación causa-efecto entre los materiales de construcción estudiados y las modificaciones que pueden ejercer sobre el campo magnético de un lugar. A continuación se estudia el entorno de radiación electromagnética artificial a baja frecuencia (3 Hz a 3 kHz) y a alta frecuencia, (800 MHz a 10 GHz) en vivienda y en oficina utilizando unas geometrías concretas: las tarjetas de corrección de radiaciones. Estas tarjetas se ubican en paramentos verticales y horizontales de un espacio sometido a radiación propia de un entorno urbano. Se concluye que en una habitación inciden múltiples variables simultáneas muy difíciles de trabajar por separado y que aparentemente no se pueden identificar cambios significativos en las mediciones con y sin las tarjetas de corrección de radiaciones. A continuación estudio el entorno de radiación electromagnética artificial a baja frecuencia asociada a la red de distribución eléctrica. Para poder ver cómo este entorno electromagnético lo podemos modificar, utilizo las tarjetas de corrección de radiaciones ubicadas en relación directa con organismos vivos, por un lado germinados de semillas de haba mungo sometidas a campos electromagnéticos complejos a alta y baja frecuencia, propios de una oficina; y por otro lado germinados de semillas de haba mungo, sometidas a campos electromagnéticos puros a 50 Hz, sin influencias de radiación a alta frecuencia. Se concluye que se observa relación causa - efecto entre los trazados geométricos estudiados y su capacidad para reducir el impacto de los campos electromagnéticos a altas y bajas frecuencias sobre las semillas de haba mungo. También utilizo las tarjetas de corrección de radiaciones en un ensayo normalizado en el laboratorio de bioelectromagnetismo del Hospital Universitario Ramón y Cajal, con células de neuroblastoma humano. Se concluye que se observa relación causa - efecto entre los trazados geométricos estudiados y su capacidad para reducir el impacto de los campos electromagnéticos de 50 Hz Y 100 μT sobre células de neuroblastoma humano y además disminuyen la velocidad de proliferación celular respecto del grupo de células de control. Finalmente se estudia el entorno de radiación electromagnética artificial a alta frecuencia, asociado a comunicaciones inalámbricas. Para ello realizo simulaciones con el software CST Studio, sobre las tarjetas de corrección de radiaciones a alta frecuencia. A la luz de los datos se observa relación causa - efecto entre el trazado geométrico estudiado y su capacidad para reducir radiaciones electromagnéticas de alta frecuencia. Se comprueba además que, las tarjetas de corrección de radiaciones disminuyen la intensidad de la radiación acercándose a los límites de exposición establecidos por el instituto de la biología de la construcción alemán, que podrían estar señalando los estándares de biocompatibilidad. ABSTRACT The perspective of the architect in environmental quality, and health in a sustainable context is extended to consider non-ionizing electromagnetic radiation in architectural design. In that sense, besides the hygrothermal, acoustic, lighting and air quality comfort, the electromagnetic comfort of an indoor space could be considered. There is still great controversy about which should be the limits of exposure to nonionizing electromagnetic radiation, as a benchmark, the more restrictive limits are considered, by the SBM- 2008 standard, developed by the Institut für Baubiologie & Oekologie Neubeuern (IBN). The hypotheses that arise are the following: the electromagnetic environment can be modified by using certain construction materials and geometry; and certain geometric design have the ability to reduce the impact of electromagnetic fields on living organisms. The aim is to demonstrate experimentally that we can work on electromagnetic environmental quality of a indoor space, by using certain construction materials and geometric design, trying to demonstrate a cause - effect relationship between them. The methodology raises three experimental approaches, each with a type of radiation, it is intend to cover situations commonly may occur in an inhabited environment, whether urban or rural. The first approach discusses the alteration of the natural magnetic field (nT / m) caused by the building materials. Geomagnetometre BPM 2010 is used for conducting a test with four types of materials from different sources: vegetable origin less processing (black agglomerate cork) and vegetable origin more processed (OSB), petroleum origin (rigid polyurethane board) and metallic origin (miniwave plate). It is observed across the data information that exist cause-effect relationship between the construction materials studied and the modifications that they can exercise on the magnetic field of a place. Then I study the environment of artificial electromagnetic radiation at low frequency (3 Hz to 3 kHz) and high frequency (800 MHz to 10 GHz) in housing and office, using some specific geometries: correcting radiation cards. These cards are placed in vertical and horizontal surfaces of an indoor space concerned by radiation. I conclude that an indoor space is affected by multiple simultaneous variables difficult to work separately and apparently it is not possible identify significant changes in measurements with and without correcting radiation cards. Then the artificial electromagnetic environment of low-frequency radiation associated with the electricity distribution network is studied. To see how the electromagnetic environment can be changed, correcting radiation cards are placed directly related to living organisms. On one hand, mung bean seeds subject to complex electromagnetic fields at low and high frequency, typical of an office; and on the other hand mung bean seeds, subjected to pure electromagnetic fields at 50 Hz, no influenced by high frequency radiation. It is observed that exist cause-effect relationship between the geometric design and their ability to reduce the impact of electromagnetic fields at high and low frequencies that arrives on on mung bean seeds. The correcting radiation cards were also used in a standard test in the bioelectromagnetics laboratory of Ramón y Cajal University Hospital, on human neuroblastoma cells. It is observed that exist cause-effect relationship between the geometric design and their ability to reduce the impact of electromagnetic fields at 50 Hz and 100 μT on human neuroblastoma cells and also decrease the rate of cell proliferation compared to the group of cells control. Finally the artificial electromagnetic radiation environment at high frequency associated with wireless communications was studied. Simulations with CST Study software were made to determine the behavior of correcting radiation cards in high-frequency. It is observed across the data information that exist causeeffect relationship between the geometric design and the ability to reduce the levels of high-frequency electromagnetic radiation. It also checks that radiation correcting cards decrease the intensity of radiation approaching exposure limits established by Institut für Baubiologie & Oekologie Neubeuern (IBN), which could be signaling biocompatibility standards.

The Dynamics of High-Speed Railway Bridges: A Review of Design Issues and New Research for Lateral Dynamics

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for the consideration of safe running conditions for the trains. In this work we start by reviewing the relevance of some basic design aspects. The significance of impact factor envelopes for moving loads is considered first. Resonance which may be achieved for high-speed trains requires dynamic analysis, for which some key aspects are discussed. The relevance of performing a longitudinal distribution of axle loads, the number of modes taken in analysis, and the consideration of vehicle-structure interaction are discussed with representative examples. The lateral dynamic effects of running trains on bridges is of importance for laterally compliant viaducts, such as some very tall structures erected in new high-speed lines. The relevance of this study is mainly for the safety of the traffic, considering both internal actions such as the hunting motion as well as external actions such as wind or earthquakes [1]. These studies require three-dimensional dynamic coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework [2]. The wheel-rail contact has been considered using a FastSim algorithm which provides a compromise between accuracy and computational cost, and captures the main nonlinear response of the contact interface. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the dynamic interaction between bridge and vehicle. The second application is to a real HS viaduct with a long continuous deck and tall piers and high lateral compliance [3]. The results show the safety of the traffic as well as the importance of considering features such as track alignment irregularities.

Dynamics of high-speed railway bridges: review of design issues and new research for lateral dynamics

Revisión y puesta al día de la publicaciones relacionadas con el diseño de puentes de ferrocarril de alta velocidad y nuevas investigaciones sobre dinámica lateral.

Simulation model for the study of overhead rail current collector systems dynamics, focused on the design of a new conductor rail

Overhead rigid conductor arrangements for current collection for railway traction have some advantages compared to other, more conventional, energy supply systems. They are simple, robust and easily maintained, not to mention their flexibility as to the required height for installation, which makes them particularly suitable for use in subway infrastructures. Nevertheless, due to the increasing speeds of new vehicles running on modern subway lines, a more efficient design is required for this kind of system. In this paper, the authors present a dynamic analysis of overhead conductor rail systems focused on the design of a new conductor profile with a dynamic behaviour superior to that of the system currently in use. This means that either an increase in running speed can be attained, which at present does not exceed 110 km/h, or an increase in the distance between the rigid catenary supports with the ensuing saving in installation costs. This study has been carried out using simulation techniques. The ANSYS programme has been used for the finite element modelling and the SIMPACK programme for the elastic multibody systems analysis.

Improved design of an overhead rail current conductor for application in underground lines

Overhead rail current collector systems for railway traction offer certain features, such as low installation height and reduced maintenance, which make them predominantly suitable for use in underground train infrastructures. Due to the increased demands of modern catenary systems and higher running speeds of new vehicles, a more capable design of the conductor rail is needed. A new overhead conductor rail has been developed and its design has been patented [13]. Modern simulation and modelling techniques were used in the development approach. The new conductor rail profile has a dynamic behaviour superior to that of the system currently in use. Its innovative design permits either an increase of catenary support spacing or a higher vehicle running speed. Both options ensure savings in installation or operating costs. The simulation model used to optimise the existing conductor rail profile included both a finite element model of the catenary and a three-dimensional multi-body system model of the pantograph. The contact force that appears between pantograph and catenary was obtained in simulation. A sensitivity analysis of the key parameters that influence in catenary dynamics was carried out, finally leading to the improved design.

Comparison of vibration and rolling noise emission of resilient and solid monobloc railway wheels in underground lines

Flat or worn wheels rolling on rough or corrugated tracks can provoke airborne noise and ground-borne vibration, which can be a serious concern for nearby neighbours of urban rail transit lines. Among the various treatments used to reduce vibration and noise, resilient wheels play an important role. In conventional resilient wheels, a slightly prestressed V­shaped rubber ring is mounted between the steel wheel centre and tyre. The elastic layer enhances rolling noise and vibration suppression, as well as impact reduction on the track. In this paper the effectiveness of resilient wheels in underground lines, in comparison to monobloc ones, is assessed. The analysed resilient wheel is able to carry greater loads than standard resilient wheels used for light vehicles. It also presents a greater radial resiliency and a higher axial stiffness than conventional V­wheels. The finite element method was used in this study. A quarter car model was defined, in which the wheelset was modelled as an elastic body. Several simulations were performed in order to assess the vibrational behaviour of elastic wheels, including modal, harmonic and random vibration analysis, the latter allowing the introduction of realistic vertical track irregularities, as well as the influence of the running speed. Due to numerical problems some simplifications were needed. Parametric variations were also performed, in which the sensitivity of the whole system to variations of rubber prestress and Poisson’s ratio of the elastic material was assessed.Results are presented in the frequency domain, showing a better performance of the resilient wheels for frequencies over 200 Hz. This result reveals the ability of the analyzed design to mitigate rolling noise, but not structural vibrations, which are primarily found in the lower frequency range.

Application of virtual certification techniques to vehicle design and track maintenance

Virtual certification partially substitutes by computer simulations the experimental techniques required for rail vehicle certification. In this paper, several works were these techniques were used in the vehicle design and track maintenance processes are presented. Dynamic simulation of multibody systems was used to virtually apply the EN14363 standard to certify the dynamic behaviour of vehicles. The works described are: assessment of a freight bogie design adapted to meter-gauge, assessment of a railway track layout for a subway network, freight bogie design with higher speed and axle load, and processing of the data acquired by a track recording vehicle for track maintenance.

Simulation techniques for design of overhead conductor rail lines for speeds over 140 km/h

In overhead conductor rail lines, aluminium beams are usually mounted with support spacing between 8 and 12 meters, to limit the maximum vertical deflection in the center of the span. This small support spacing limits the use of overhead conductor rail to tunnels, therefore it has been used almost exclusively in metropolitan networks, with operation speeds below 110 km/h. Nevertheless, due to the lower cost of maintenance required for this electrification system, some railway administrations are beginning to install it in some tunnels on long-distance lines, requesting higher operation speeds [1]. Some examples are the Barcelona and Madrid suburban networks (Spain), and recent lines in Turkey and Malaysia. In order to adapt the design of the overhead conductor for higher speeds (V > 160 km/h), particular attention must be paid to the geometry of the conductor rail in critical zones as overlaps, crossings and, especially, transitions between conductor rail and conventional catenary, since the use of overhead conductor rail is limited to tunnels, as already mentioned. This paper describes simulation techniques developed in order to take into account these critical zones. Furthermore, some specific simulations results are presented that have been used to analyze and optimizes the geometry of this special zones to get a better current collection quality, in a real suburban network. This paper presents the work undertaken by the Railways Technology Research Centre (CITEF), having over 10 years of experience in railways research [1-4].

Tiled Projector Displays Correction for Dark Scenes in Railway Simulators

Tiled projector displays are a common choice for training simulators, where a high resolution output image is required. They are cheap for the resolution that they can reach and can be configured in many different ways. Nevertheless, such kinds of displays require geometric and color correction so that the composite image looks seamless. Display correction is an even bigger challenge when the projected images include dark scenes combined with brighter scenes. This is usually a problem for railway simulators when the train is positioned inside a tunnel and the black offset effect becomes noticeable. In this paper, a method for fast photometric and geometric correction of tiled display systems where dark and bright scenes are combined is presented. The image correction is carried out in two steps. First, geometric alignment and overlapping areas attenuation for brighter scenes is applied. Second, in the event of being inside a tunnel, the brightness of the scene is increased in certain areas using light sources in order to create the impression of darkness but minimizing the effect of the black offset