Effectiveness of resilient wheels in reducing noise and vibrations

This study focuses on the effectiveness of resilient wheels in reducing railway noise and vibrations, and compares the effectiveness of three types of wheels. The finite elements method has been used to characterise the vibratory behaviour of these wheels. The model has been excited with a realistic spectrum of vertical track irregularities, and a spectral analysis has been carried out. Results have been post-processed in order to estimate the sound power emitted. These calculations have been used to assess the effectiveness of the resilient wheel designs in reducing noise emitted to the environment and in propagating structural vibrations.

Comparison of vibration and rolling noise emission of resilient and solid monobloc railway wheels in underground lines

Flat or worn wheels rolling on rough or corrugated tracks can provoke airborne noise and ground-borne vibration, which can be a serious concern for nearby neighbours of urban rail transit lines. Among the various treatments used to reduce vibration and noise, resilient wheels play an important role. In conventional resilient wheels, a slightly prestressed V­shaped rubber ring is mounted between the steel wheel centre and tyre. The elastic layer enhances rolling noise and vibration suppression, as well as impact reduction on the track. In this paper the effectiveness of resilient wheels in underground lines, in comparison to monobloc ones, is assessed. The analysed resilient wheel is able to carry greater loads than standard resilient wheels used for light vehicles. It also presents a greater radial resiliency and a higher axial stiffness than conventional V­wheels. The finite element method was used in this study. A quarter car model was defined, in which the wheelset was modelled as an elastic body. Several simulations were performed in order to assess the vibrational behaviour of elastic wheels, including modal, harmonic and random vibration analysis, the latter allowing the introduction of realistic vertical track irregularities, as well as the influence of the running speed. Due to numerical problems some simplifications were needed. Parametric variations were also performed, in which the sensitivity of the whole system to variations of rubber prestress and Poisson’s ratio of the elastic material was assessed.Results are presented in the frequency domain, showing a better performance of the resilient wheels for frequencies over 200 Hz. This result reveals the ability of the analyzed design to mitigate rolling noise, but not structural vibrations, which are primarily found in the lower frequency range.

High speed railroad bridges. Conception, bases of design, typological possibilities and construction methods

Diseño conceptual de puentes de alta velocidad ferroviarios. Railroad bridges, in general, and those for high speed railways, in particular, demand very special conditions. The traffic loads are much higher than for road bridges. Loads due to braking and acceleration determine, due to their magnitude, the structural layout. Because of the speed of the vehicles there are specific dynamic effects which need to be considered. In order to ensure passenger comfort, compatible with speeds of up to 350 km/h, it is necessary to meet very demanding conditions with respect to stiffness, displacements and dynamic behavior. In this paper these conditions are briefly described and different typological possibilities to satisfy them are presented as well as the main construction methods applicable to this kind of bridges.

Effects of traffic loads on reinforced concrete railroad culverts

In the context of the present conference paper culverts are defined as an opening or conduit passing through an embankment usually for the purpose of conveying water or providing safe pedestrian and animal crossings under rail infrastructure. The clear opening of culverts may reach values of up to 12m however, values around 3m are encountered much more frequently. Depending on the topography, the number of culverts is about 10 times that of bridges. In spite of this, their dynamic behavior has received far less attention than that of bridges. The fundamental frequency of culverts is considerably higher than that of bridges even in the case of short span bridges. As the operational speed of modern high-speed passenger rail systems rises, higher frequencies are excited and thus more energy is encountered in frequency bands where the fundamental frequency of box culverts is located. Many research efforts have been spent on the subject of ballast instability due to bridge resonance, since it was first observed when high-speed trains were introduced to the Paris/Lyon rail line. To prevent this phenomenon from occurring, design codes establish a limit value for the vertical deck acceleration. Obviously one needs some sort of numerical model in order to estimate this acceleration level and at that point things get quite complicated. Not only acceleration but also displacement values are of interest e.g. to estimate the impact factor. According to design manuals the structural design should consider the depth of cover, trench width and condition, bedding type, backfill material, and compaction. The same applies to the numerical model however, the question is: What type of model is appropriate for this job? A 3D model including the embankment and an important part of the soil underneath the culvert is computationally very expensive and hard to justify taking into account the associated costs. Consequently, there is a clear need for simplified models and design rules in order to achieve reasonable costs. This paper will describe the results obtained from a 2D finite element model which has been calibrated by means of a 3D model and experimental data obtained at culverts that belong to the high-speed railway line that links the two towns of Segovia and Valladolid in Spain

Dynamic analysis of road vehicle-bridge systems under turbulent wind by means of Finite Element Models

When an automobile passes over a bridge dynamic effects are produced in vehicle and structure. In addition, the bridge itself moves when exposed to the wind inducing dynamic effects on the vehicle that have to be considered. The main objective of this work is to understand the influence of the different parameters concerning the vehicle, the bridge, the road roughness or the wind in the comfort and safety of the vehicles when crossing bridges. Non linear finite element models are used for structures and multibody dynamic models are employed for vehicles. The interaction between the vehicle and the bridge is considered by contact methods. Road roughness is described by the power spectral density (PSD) proposed by the ISO 8608. To consider that the profiles under right and left wheels are different but not independent, the hypotheses of homogeneity and isotropy are assumed. To generate the wind velocity history along the road the Sandia method is employed. The global problem is solved by means of the finite element method. First the methodology for modelling the interaction is verified in a benchmark. Following, the case of a vehicle running along a rigid road and subjected to the action of the turbulent wind is analyzed and the road roughness is incorporated in a following step. Finally the flexibility of the bridge is added to the model by making the vehicle run over the structure. The application of this methodology will allow to understand the influence of the different parameters in the comfort and safety of road vehicles crossing wind exposed bridges. Those results will help to recommend measures to make the traffic over bridges more reliable without affecting the structural integrity of the viaduct

Acondicionamiento y procesado de señales mediante bus CAN en vehículos monoplaza

En este proyecto se ha diseñado un sistema de adquisición y uso compartido de datos orientado a la implantación en un vehículo monoplaza de Formula SAE. Más concretamente, se encarga de recoger la información proporcionada por cuatro sensores infrarrojos de temperatura que sondearán constantemente la temperatura a la que se encuentran las ruedas del vehículo. La información, recogida en una memoria de almacenamiento masivo, se compartirá con otros dispositivos mediante un bus común. Los sensores empleados para generar la información los proporciona Melexis. Dichos sensores permiten estar todos simultáneamente conectados en un bus común gracias a su electrónica interna. Mediante el bus I2C irán conectados los cuatro sensores de nuestra aplicación (uno por cada rueda) permitiéndose añadir a posteriori más sensores o incluso otros elementos que permitan la comunicación por este tipo de bus I2C. La gestión de las tareas se realiza mediante el microcontrolador DSPIC33FJ256GP710-I/PF proporcionado por Microchip. Este es un microcontrolador complejo, por lo que para nuestra aplicación desaprovecharemos parte de su potencial. En nuestra tarjeta ha sido solamente añadido el uso de los dos I2C (uno para la tarjeta SD y el otro para los sensores), el módulo ECAN1 (para las comunicaciones por bus CAN), el módulo SPI (para acceder a una memoria Flash), 4 ADCs (para posibles mediciones) y 2 entradas de interrupción (para posible interactuación con el usuario), a parte de los recursos internos necesarios. En este proyecto se realiza tanto el desarrollo de una tarjeta de circuito impreso dedicada a resolver la funcionalidad requerida, así como su programación a través del entorno de programación facilitado por Microchip, el ICD2 Programmer. In this project, an acquisition and sharing system of data, which is oriented to be installed in a Formula SAE single-seater vehicle, has been designed. Concretely, it is responsible for getting the information supplied by four IR temperature sensors that monitor the wheels temperature. The information, which is loaded in a massive storage memory, will be shared with other devices by means of a common bus. The sensors used to generate the information are supplied by Melexis. Such specific sensors let that all they can be connected to the same bus at the same time due to their internal electronic. The four sensors will be connected through an I2C bus, one for each wheel, although we could add later more sensors or even other devices that they were able to let the I2C communication. Tasks management will be done by means of the DSPIC33FJ256GP710-I/PF microcontroller, which will be supplied by Microchip. This is a complex microcontroller, so, in our application we waste off a part of its potential. In our PCB has only been incorporated the use of the two I2C (one for the SD card and the other for the sensors), the ECAN module (to communicate devices), the SPI module (to access to the Flash memory), 4 ADC’s (for possible measurements) and 2 interrupt inputs (for possible inter-action with the user), a part of the necessary internal resources. This project aims the PCB development dedicated to solve the requested functionality and its programming through the programming environment provided by Microchip (the ICD2 programmer).

Diseño y Desarrollo de un Robot de Inspección de Tuberías

El siguiente trabajo presenta un desarrollo innovador de un Robot de Inspección de Tuberías, el cual fue diseñado para operación de Tuberías Verticales (RETOV Robot de operación en tuberías Verticales (siglas en Español)). Cuando RETOV es usado para inspeccionar pozos petroleros, puede ser controlado desde la superficie, esto permite al operador la inspección y monitoreo del pozo. Esto es efectuado a través de una interfaz de usuario que controla el Robot. RETOV fue diseñado con anillos articulados que abrazan la tubería, un nuevo sistema de amortiguación y ruedas móviles brinda la posibilidad de navegar y evitar obstáculos en la tubería realizando tres tipos de movimientos: rotación, traslación y helicoidal. Adicionalmente RETOV fue diseñado para realizar inspección entre dos tuberías(la tubería de producción y el pozo petrolero), con un sistema de seguridad y una estructura liviana, RETOV puede ser equipado con sensores para medir las variables de interés en el pozo. El diseño de la mecánica y el programa de control, la instrumentación, los modelos matemáticos y resultados de las pruebas han sido descritos en esta Tesis. The following Doctoral Thesis presents an innovative application of a Pipe Inspection Robot, which was designed especially as Operation Robot in Vertical Pipes (RETOV) (Robot for operation vertical pipes (Spanish acronyms)). When RETOV is used to inspect Oil Well, can be controlled from the surface, it´s allow the operator the well inspection and monitoring. This is done through our interface that controls the robot. The RETOV was designed with an articulated ring systems that embrace the pipe, a new damping systems and mobile wheels bring the possibility to navigate and avoid obstacles into the well, performing three types of movement: Rotational, translational and screw. Additional, RETOV was designed to perform the inspection between two pipes (pipe and oil well production), with a security braking systems and lightweight structure; RETOV can be equipment with sensors to measure the variables of interest in the well. The hardware and Software design, the instrumentation, the mathematical models, and the test results have been described in this thesis.

Do charges to freight trucks and trains in the European Union reflect their social marginal costs? Application to the case of Spain

In the last few years, the European Union (EU) has become greatly concerned about the environmental costs of road transport in Europe as a result of the constant growth in the market share of trucks and the steady decline in the market share of railroads. In order to reverse this trend, the EU is promoting the implementation of additional charges for heavy goods vehicles (HGV) on the trunk roads of the EU countries. However, the EU policy is being criticised because it does not address the implementation of charges to internalise the external costs produced by automobiles and other transport modes such as railroad. In this paper, we first describe the evolution of the HGV charging policy in the EU, and then assess its practical implementation across different European countries. Second, and of greater significance, by using the case study of Spain, we evaluate to what extent the current fees on trucks and trains reflect their social marginal costs, and consequently lead to an allocative-efficient outcome. We found that for the average case in Spain the truck industry meets more of the marginal social cost produced by it than does the freight railroad industry. The reason for this lies in the large sums of money paid by truck companies in fuel taxes, and the subsidies that continue to be granted by the government to the railroads.

Cobertura de la trinchera ferroviaria de Hendaya

Un problema del ferrocarril al paso por las ciudades europeas es el efecto barrera generado, que impide su desarrollo más allá de las vías. Si se salta la barrera lo cierto es que ello se hace sólo en sitios concretos y el efecto psicológico de aislamiento persiste para los habitantes del entorno. Este trabajo presenta de manera sucinta los problemas de concepción, comprobación y vibraciones planteados por la estructura de cubierta de la trinchera ferroviaria de Hendaya, consistente en una losa de hormigón pretensado y luz variable de 20-40 metros, que resuelve el problema de aislamiento entre las dos partes de la ciudad. Su construcción ha sido posible gracias al acuerdo entre la SNCF e inversores privados y está permitiendo la construcción sobre ella de 6 edificios de viviendas y una residencia de turismo, la demolición del antiguo ?Pont-Vieux? y la construcción de un nuevo ?Pont-Vieux?, integrado completamente en la promoción inmobiliaria. An important problem put by the train in its passage by the cities of Europe generally and in France in particular is the effect barrier which builds up, preventing the cities from developing beyond. Even if this barrier is crossed, it is certain that the passage is restricted to concrete places and always acts as psychological barrier for the local residents. This article presents in a brief way the problems of conception, analysis and vibration of the cover structure of the railroad trench of Hendaye. This structure consists of a 20-40 meters span slab of pre-stressed concrete that solves the isolation problem of both parts of the town of Hendaye. Its construction was possible thanks to the agreement of the SNCF (French Railways)and some private investors, and is allowing the investors the construction on top of 6 residential buildings and a holiday residence, with demolition of the ancient “Pont-Vieux” and building of a new “Pont-Vieux”, which is completely integrated into the real-estate development. Special attention is given to the change of transverse cross-section of the slab during construction stages, which originates a redistribution of stresses, and to the long-term equilibrium of horizontal forces.

Wheel-Rail Contact Forces in High-Speed Simply Supported Bridges at Resonance

The response of high-speed bridges at resonance, particularly under flexural vibrations, constitutes a subject of research for many scientists and engineers at the moment. The topic is of great interest because, as a matter of fact, such kind of behaviour is not unlikely to happen due to the elevated operating speeds of modern rains, which in many cases are equal to or even exceed 300 km/h ( [1,2]). The present paper addresses the subject of the evolution of the wheel-rail contact forces during resonance situations in simply supported bridges. Based on a dimensionless formulation of the equations of motion presented in [4], very similar to the one introduced by Klasztorny and Langer in [3], a parametric study is conducted and the contact forces in realistic situations analysed in detail. The effects of rail and wheel irregularities are not included in the model. The bridge is idealised as an Euler-Bernoulli beam, while the train is simulated by a system consisting of rigid bodies, springs and dampers. The situations such that a severe reduction of the contact force could take place are identified and compared with typical situations in actual bridges. To this end, the simply supported bridge is excited at resonace by means of a theoretical train consisting of 15 equidistant axles. The mechanical characteristics of all axles (unsprung mass, semi-sprung mass, and primary suspension system) are identical. This theoretical train permits the identification of the key parameters having an influence on the wheel-rail contact forces. In addition, a real case of a 17.5 m bridges traversed by the Eurostar train is analysed and checked against the theoretical results. The influence of three fundamental parameters is investigated in great detail: a) the ratio of the fundamental frequency of the bridge and natural frequency of the primary suspension of the vehicle; b) the ratio of the total mass of the bridge and the semi-sprung mass of the vehicle and c) the ratio between the length of the bridge and the characteristic distance between consecutive axles. The main conclusions derived from the investigation are: The wheel-rail contact forces undergo oscillations during the passage of the axles over the bridge. During resonance, these oscillations are more severe for the rear wheels than for the front ones. If denotes the span of a simply supported bridge, and the characteristic distance between consecutive groups of loads, the lower the value of , the greater the oscillations of the contact forces at resonance. For or greater, no likelihood of loss of wheel-rail contact has been detected. The ratio between the frequency of the primary suspension of the vehicle and the fundamental frequency of the bridge is denoted by (frequency ratio), and the ratio of the semi-sprung mass of the vehicle (mass of the bogie) and the total mass of the bridge is denoted by (mass ratio). For any given frequency ratio, the greater the mass ratio, the greater the oscillations of the contact forces at resonance. The oscillations of the contact forces at resonance, and therefore the likelihood of loss of wheel-rail contact, present a minimum for approximately between 0.5 and 1. For lower or higher values of the frequency ratio the oscillations of the contact forces increase. Neglecting the possible effects of torsional vibrations, the metal or composite bridges with a low linear mass have been found to be the ones where the contact forces may suffer the most severe oscillations. If single-track, simply supported, composite or metal bridges were used in high-speed lines, and damping ratios below 1% were expected, the minimum contact forces at resonance could drop to dangerous values. Nevertheless, this kind of structures is very unusual in modern high-speed railway lines.

Bridge for the airbus A-380 in Barajas airport (Spain)

During the years 2004 and 2005 is has been constructed in Barajas airport of Madrid a special bridge for the new plane AIRBUS A380. This new airplane has a weight of 1,500,000 pounds and 18 wheels with a reaction of 39.2 tonnes per each one and the braking force is about 600 tonnes. The enormous loads transmitted for the airplane made this bridge a special structure. The present article exposes the most important characteristics of project and construction, of one of the special bridges in the airport Brajas of Madri. This bridge was constructed for the access to the hangar of airplanes in Barajas, known "La Muñoza". The structure has a width of 48m, two spans of 13 m each one and a vertical clearance of 5.50 m to allow passing vehicles under it, along thhe new motorway in Brajas (Madrid).

Arquitectura de Control para la Conducción Autónoma de Vehículos en Entornos Urbanos y Autovías

Hoy en día, el desarrollo tecnológico en el campo de los sistemas inteligentes de transporte (ITS por sus siglas en inglés) ha permitido dotar a los vehículos con diversos sistemas de ayuda a la conducción (ADAS, del inglés advanced driver assistance system), mejorando la experiencia y seguridad de los pasajeros, en especial del conductor. La mayor parte de estos sistemas están pensados para advertir al conductor sobre ciertas situaciones de riesgo, como la salida involuntaria del carril o la proximidad de obstáculos en el camino. No obstante, también podemos encontrar sistemas que van un paso más allá y son capaces de cooperar con el conductor en el control del vehículo o incluso relegarlos de algunas tareas tediosas. Es en este último grupo donde se encuentran los sistemas de control electrónico de estabilidad (ESP - Electronic Stability Program), el antibloqueo de frenos (ABS - Anti-lock Braking System), el control de crucero (CC - Cruise Control) y los más recientes sistemas de aparcamiento asistido. Continuando con esta línea de desarrollo, el paso siguiente consiste en la supresión del conductor humano, desarrollando sistemas que sean capaces de conducir un vehículo de forma autónoma y con un rendimiento superior al del conductor. En este trabajo se presenta, en primer lugar, una arquitectura de control para la automatización de vehículos. Esta se compone de distintos componentes de hardware y software, agrupados de acuerdo a su función principal. El diseño de la arquitectura parte del trabajo previo desarrollado por el Programa AUTOPIA, aunque introduce notables aportaciones en cuanto a la eficiencia, robustez y escalabilidad del sistema. Ahondando un poco más en detalle, debemos resaltar el desarrollo de un algoritmo de localización basado en enjambres de partículas. Este está planteado como un método de filtrado y fusión de la información obtenida a partir de los distintos sensores embarcados en el vehículo, entre los que encontramos un receptor GPS (Global Positioning System), unidades de medición inercial (IMU – Inertial Measurement Unit) e información tomada directamente de los sensores embarcados por el fabricante, como la velocidad de las ruedas y posición del volante. Gracias a este método se ha conseguido resolver el problema de la localización, indispensable para el desarrollo de sistemas de conducción autónoma. Continuando con el trabajo de investigación, se ha estudiado la viabilidad de la aplicación de técnicas de aprendizaje y adaptación al diseño de controladores para el vehículo. Como punto de partida se emplea el método de Q-learning para la generación de un controlador borroso lateral sin ningún tipo de conocimiento previo. Posteriormente se presenta un método de ajuste on-line para la adaptación del control longitudinal ante perturbaciones impredecibles del entorno, como lo son los cambios en la inclinación del camino, fricción de las ruedas o peso de los ocupantes. Para finalizar, se presentan los resultados obtenidos durante un experimento de conducción autónoma en carreteras reales, el cual se llevó a cabo en el mes de Junio de 2012 desde la población de San Lorenzo de El Escorial hasta las instalaciones del Centro de Automática y Robótica (CAR) en Arganda del Rey. El principal objetivo tras esta demostración fue validar el funcionamiento, robustez y capacidad de la arquitectura propuesta para afrontar el problema de la conducción autónoma, bajo condiciones mucho más reales a las que se pueden alcanzar en las instalaciones de prueba. ABSTRACT Nowadays, the technological advances in the Intelligent Transportation Systems (ITS) field have led the development of several driving assistance systems (ADAS). These solutions are designed to improve the experience and security of all the passengers, especially the driver. For most of these systems, the main goal is to warn drivers about unexpected circumstances leading to risk situations such as involuntary lane departure or proximity to other vehicles. However, other ADAS go a step further, being able to cooperate with the driver in the control of the vehicle, or even overriding it on some tasks. Examples of this kind of systems are the anti-lock braking system (ABS), cruise control (CC) and the recently commercialised assisted parking systems. Within this research line, the next step is the development of systems able to replace the human drivers, improving the control and therefore, the safety and reliability of the vehicles. First of all, this dissertation presents a control architecture design for autonomous driving. It is made up of several hardware and software components, grouped according to their main function. The design of this architecture is based on the previous works carried out by the AUTOPIA Program, although notable improvements have been made regarding the efficiency, robustness and scalability of the system. It is also remarkable the work made on the development of a location algorithm for vehicles. The proposal is based on the emulation of the behaviour of biological swarms and its performance is similar to the well-known particle filters. The developed method combines information obtained from different sensors, including GPS, inertial measurement unit (IMU), and data from the original vehicle’s sensors on-board. Through this filtering algorithm the localization problem is properly managed, which is critical for the development of autonomous driving systems. The work deals also with the fuzzy control tuning system, a very time consuming task when done manually. An analysis of learning and adaptation techniques for the development of different controllers has been made. First, the Q-learning –a reinforcement learning method– has been applied to the generation of a lateral fuzzy controller from scratch. Subsequently, the development of an adaptation method for longitudinal control is presented. With this proposal, a final cruise control controller is able to deal with unpredictable environment disturbances, such as road slope, wheel’s friction or even occupants’ weight. As a testbed for the system, an autonomous driving experiment on real roads is presented. This experiment was carried out on June 2012, driving from San Lorenzo de El Escorial up to the Center for Automation and Robotics (CAR) facilities in Arganda del Rey. The main goal of the demonstration was validating the performance, robustness and viability of the proposed architecture to deal with the problem of autonomous driving under more demanding conditions than those achieved on closed test tracks.

VladBot. Robot para posicionamiento de medida

VladBot es un robot autónomo diseñado para posicionar en interiores un micrófono de medida. Este prototipo puede valorar la idea de automatizar medidas acústicas en interiores mediante un robot autónomo. Posee dos ruedas motrices y una rueda loca. Ésta rueda loca aporta maniobrabilidad al robot. Un soporte extensible hecho de aluminio sostiene el micrófono de medida. VladBot ha sido diseñado con tecnologías de bajo coste y bajo una plataforma abierta, Arduino. Arduino es una plataforma electrónica libre. Esto quiere decir que los usuarios tienen libre acceso a toda la información referente a los micro-controladores (hardware) y referente al software. Ofrece un IDE (Integrated Development Environment, en español, Entorno de Desarrollo Integrado) de forma gratuita y con un sencillo lenguaje de programación, con el que se pueden realizar proyectos de cualquier tipo. Además, los usuarios disponen de un foro donde encontrar ayuda, “Arduino Forum”. VladBot se comunica con el usuario a través de Bluetooth, creando un enlace fiable y con un alcance suficiente (aproximadamente 100 metros) para que controlar a VladBot desde una sala contigua. Hoy en día, Bluetooth es una tecnología implantada en casi todos los ordenadores, por lo que no necesario ningún sistema adicional para crear dicho enlace. Esta comunicación utiliza un protocolo de comunicaciones, JSON (JavaScript Object Notation). JSON hace que la comunicación sea más fiable, ya que sólo un tipo de mensajes preestablecidos son reconocidos. Gracias a este protocolo es posible la comunicación con otro software, permitiendo crear itinerarios en otro programa externo. El diseño de VladBot favorece su evolución hasta un sistema más preciso ya que el usuario puede realizar modificaciones en el robot. El código que se proporciona puede ser modificado, aumentando las funcionalidades de VladBot o mejorándolas. Sus componentes pueden ser cambiados también (incluso añadir nuevos dispositivos) para aumentar sus capacidades. Vladbot es por tanto, un sistema de transporte (de bajo coste) para un micrófono de medida que se puede comunicar inalámbricamente con el usuario de manera fiable. ABSTRACT. VladBot is an autonomous robot designed to indoor positioning of a measurement microphone. This prototype can value the idea of making automatic acoustic measurements indoor with an autonomous robot. It has two drive wheels and a caster ball. This caster ball provides manoeuvrability to the robot. An extendible stand made in aluminium holds the measurement microphone. VladBot has been designed with low cost technologies and under an open-source platform, Arduino. Arduino is a freeFsource electronics platform. This means that users have free access to all the information about micro-controllers (hardware) and about the software. Arduino offers a free IDE (Integrated Development Environment) with an easy programming language, which any kind of project can be made with. Besides, users have a forum where find help, “Arduino Forum”. VladBot communicates with the user by Bluetooth, creating a reliable link with enough range (100 meters approximately) for controlling VladBot in the next room. Nowadays, Bluetooth is a technology embedded in almost laptops, so it is not necessary any additional system for create this link. This communication uses a communication protocol, JSON (JavaScript Object Notation). JSON makes the communication more reliable, since only a preFestablished kind of messages are recognised. Thanks to this protocol is possible the communication with another software, allowing to create routes in an external program. VladBot´s design favours its evolution to an accurate system since the user can make modifications in the robot. The code given can be changed, increasing VladBot´s uses or improving these uses. Their components can be changed too (even new devices can be added) for increasing its abilities. So, VladBot is a (low cost) transport system for a measurement microphone, which can communicate with the user in a reliable way.

Influence of the track quality and of the properties of the wheel rail rolling contact on vehicle dynamics

This work describes an analytical approach to determine what degree of accuracy is required in the definition of the rail vehicle models used for dynamic simulations. This way it would be possible to know in advance how the results of simulations may be altered due to the existence of errors in the creation of rolling stock models, whilst also identifying their critical parameters. This would make it possible to maximize the time available to enhance dynamic analysis and focus efforts on factors that are strictly necessary.In particular, the parameters related both to the track quality and to the rolling contact were considered in this study. With this aim, a sensitivity analysis was performed to assess their influence on the vehicle dynamic behaviour. To do this, 72 dynamic simulations were performed modifying, one at a time, the track quality, the wheel-rail friction coefficient and the equivalent conicity of both new and worn wheels. Three values were assigned to each parameter, and two wear states were considered for each type of wheel, one for new wheels and another one for reprofiled wheels.After processing the results of these simulations, it was concluded that all the parameters considered show very high influence, though the friction coefficient shows the highest influence. Therefore, it is recommended to undertake any future simulation job with measured track geometry and track irregularities, measured wheel profiles and normative values of wheel-rail friction coefficient.

Modelo gráfico para la datación de vías romanas empedradas a partir del estudio de sus estados de frecuentación y del análisis superficial de roderas

La presente tesis doctoral se orienta al estudio y análisis de los caminos empedrados antiguos, desde la época prerromana, tanto desde el punto de vista histórico como desde el técnico. La cuantificación de la romanidad de un camino representa un objetivo importante para la mayoría de los estudiosos de la caminería antigua, así como para los arqueólogos, por los datos que ofrece acerca del uso del territorio, los trazados de caminos en la antigüedad y los tráficos asociados. Cuantificar la romanidad de un camino no es tarea sencilla debido a que intervienen multitud de condicionantes que están vivos y son cambiantes como consecuencia del dinamismo inherente al propio camino. En cuanto al aspecto histórico, se realiza una descripción y análisis de la evolución del camino en la Península Ibérica desde sus orígenes hasta mediados del siglo XX, que permite diferenciar la red itineraria según su momento histórico. Así mismo, se describen y analizan: las ruedas y los carros desde sus orígenes, especialmente en la época romana -incluyendo una toma de medidas de distintos tipos de carro, existentes en instituciones y colecciones particulares-; las técnicas de transporte en la antigüedad y las características de la infraestructura viaria de época romana, detallando aspectos generales de sus técnicas de ingeniería y construcción. Desde el punto de vista técnico, el enfoque metodológico ha sido definir un Índice de Romanidad del Camino (IRC) para la datación de vías romanas empedradas, basado en un análisis multicriterio, a partir de los distintos factores que caracterizan su romanidad. Se ha realizado un exhaustivo estudio de campo, con la correspondiente toma de datos en las vías. Se han realizado una serie de ensayos de laboratorio con un prototipo creado exprofeso para simular el desgaste de la piedra producido por el traqueteo del carro al circular por el camino empedrado y dar una hipótesis de datación del camino. Se ha realizado un tratamiento estadístico con la muestra de datos medidos en campo. Se ha definido además el concepto de elasticidad de rodera usando la noción de derivada elástica. En cuanto a los resultados obtenidos: se ha calculado el Índice de Romanidad del Camino (IRC) en una serie de vías empedradas, para cuantificar su romanidad, obteniéndose un resultado coherente con la hipótesis previa sobre la datación de dichas vías; y se ha formulado un modelo exponencial para el número de frecuentaciones de carga que lo relaciona con la elasticidad de rodera y con su esbeltez y que se ha utilizado para relacionar la elasticidad de la rodera con la geología de la roca. Se ha iniciado una línea de investigación sobre la estimación de tráficos históricos en la caminería antigua, considerando que el volumen de tráfico a lo largo del tiempo en un tramo de vía está relacionado con los valores de elasticidad de rodera de dicho tramo a través de la tipología de la roca. En resumen, la presente tesis doctoral proporciona un método para sistematizar el estudio de los caminos antiguos, así como para datarlos y estimar la evolución de sus tráficos. The present Ph. D. Thesis aims to study and to analyze ancient cobbled ways, since pre-roman times, both from the historical and technical points of view. The quantification of the Roman character of a way represents an important target for most of the researchers of ancient ways, as well as for the archaeologists, due to information that it offers about the use of the territory, the tracings of ways in the antiquity and the associate flows. To quantify the Roman character of a way is not a simple task because it involves multitude of influent factors that are alive and variable as a result of the dynamism inherent to the way. As for the historical aspect, a description and analysis of the evolution of the way in the Iberian Peninsula from its origins until the middle of the twentieth century has been done. This allows us to distinguish between elements of the network according to its historical moment. Likewise, a description and analysis is given about: the wheels and the cars since their origins, especially in the Roman time - including a capture of measurements of different types of car, belonging to institutions and to particular collections-; the transport techniques on the antiquity and the characteristics of the road infrastructure of Roman epoch, detailing general technical engineering and constructive aspects. From the technical point of view, the methodological approach has been to define an Index of the Roman Character of the Way (IRC) for the dating of cobbled Roman routes, based on a multi-criterion analysis, involving different factors typical of Roman ways. An exhaustive field study has been realized, with the corresponding capture of information in the routes. A series of laboratory essays has been realized with an ad hoc prototype created to simulate the wear of the stone produced by cars circulating along the cobbled way, and to give a dating hypothesis of the way. A statistical treatment has been realized with the sample of information measured in field. There has been defined also the concept of elasticity of rolling trace using the notion of elastic derivative. As for the obtained results: there has been calculated the Index of Roman Character of the Way (IRC) in a series of cobbled routes, to quantify its Roman character, obtaining a coherent result with the previous dating hypothesis of the above mentioned routes; and an exponential model has been formulated for the number of frequent attendances of load that relates this number to the elasticity of rolling trace and to its slenderness and that has been used to relate the elasticity of the rolling trace to the geology of the rock. An investigation line has been opened about the estimation of historical flows in ancient ways, considering that the traffic volume over the course of time in a route stretch is related to the values of elasticity of rolling trace of the above mentioned stretch by means of the typology of the rock. In short, the present Ph. D. Thesis provides a method to systematize the study of ancient ways, as well as to date them and to estimate the evolution of their flows.