High speed railroad bridges. Conception, bases of design, typological possibilities and construction methods

Diseño conceptual de puentes de alta velocidad ferroviarios. Railroad bridges, in general, and those for high speed railways, in particular, demand very special conditions. The traffic loads are much higher than for road bridges. Loads due to braking and acceleration determine, due to their magnitude, the structural layout. Because of the speed of the vehicles there are specific dynamic effects which need to be considered. In order to ensure passenger comfort, compatible with speeds of up to 350 km/h, it is necessary to meet very demanding conditions with respect to stiffness, displacements and dynamic behavior. In this paper these conditions are briefly described and different typological possibilities to satisfy them are presented as well as the main construction methods applicable to this kind of bridges.

Effects of traffic loads on reinforced concrete railroad culverts

In the context of the present conference paper culverts are defined as an opening or conduit passing through an embankment usually for the purpose of conveying water or providing safe pedestrian and animal crossings under rail infrastructure. The clear opening of culverts may reach values of up to 12m however, values around 3m are encountered much more frequently. Depending on the topography, the number of culverts is about 10 times that of bridges. In spite of this, their dynamic behavior has received far less attention than that of bridges. The fundamental frequency of culverts is considerably higher than that of bridges even in the case of short span bridges. As the operational speed of modern high-speed passenger rail systems rises, higher frequencies are excited and thus more energy is encountered in frequency bands where the fundamental frequency of box culverts is located. Many research efforts have been spent on the subject of ballast instability due to bridge resonance, since it was first observed when high-speed trains were introduced to the Paris/Lyon rail line. To prevent this phenomenon from occurring, design codes establish a limit value for the vertical deck acceleration. Obviously one needs some sort of numerical model in order to estimate this acceleration level and at that point things get quite complicated. Not only acceleration but also displacement values are of interest e.g. to estimate the impact factor. According to design manuals the structural design should consider the depth of cover, trench width and condition, bedding type, backfill material, and compaction. The same applies to the numerical model however, the question is: What type of model is appropriate for this job? A 3D model including the embankment and an important part of the soil underneath the culvert is computationally very expensive and hard to justify taking into account the associated costs. Consequently, there is a clear need for simplified models and design rules in order to achieve reasonable costs. This paper will describe the results obtained from a 2D finite element model which has been calibrated by means of a 3D model and experimental data obtained at culverts that belong to the high-speed railway line that links the two towns of Segovia and Valladolid in Spain

Study of the damage evolution of the concrete under freeze-thaw cycles using traditional and non-traditional techniques

Some experiments have been performed to investigate the cyclic freeze-thaw deterioration of concrete, using traditional and non-traditional techniques. Two concrete mixes, with different pore structure, were tested in order to compare the behavior of a freeze-thaw resistant concrete from one that is not. One of the concretes was air entrained, high content of cement and low w/c ratio, and the other one was a lower cement content and higher w/c ratio, without air-entraining agent. Concrete specimens were studied under cyclic freeze-thaw conditions according to UNE-CENT/TS 12390-9 test, using 3% NaCl solution as freezing medium (CDF test: Capillary Suction, De-icing agent and Freeze-thaw Test). The temperature and relative humidity were measured during the cycles inside the specimens using embedded sensors placed at different heights from the surface in contact with the de-icing agent solution. Strain gauges were used to measure the strain variations at the surface of the specimens. Also, measurements of ultrasonic pulse velocity through the concrete specimens were taken before, during, and after the freeze-thaw cycles. According to the CDF test, the failure of the non-air-entraining agent concrete was observed before 28 freeze-thaw cycles; contrariwise, the scaling of the air-entraining agent concrete was only 0.10 kg/m 2 after 28 cycles, versus 3.23 kg/m 2 in the deteriorated concrete, after 28 cycles. Similar behavior was observed on the strain measurements. The residual strain in the deteriorated concrete after 28 cycles was 1150 m versus 65 m, in the air-entraining agent concrete. By means of monitoring the changes of ultrasonic pulse velocity during the freeze-thaw cycles, the deterioration of the tested specimens were assessed

Using the Own Flexibility of a Climbing Robot as a Double Force Sensor

Force sensors are used when interaction tasks are carried out by robots in general, and by climbing robots in particular. If the mechanics and electronics systems are contained inside the own robot, the robot becomes portable without external control. Commercial force sensors cannot be used due to limited space and weight. By selecting the links material with appropriate stiffness and placing strain gauges on the structure, the own robot flexibility can be used such as force sensor. Thus, forces applied on the robot tip can be measured without additional external devices. Only gauges and small internal electronic converters are necessary. This paper illustrates the proposed algorithm to achieve these measurements. Additionally, experimental results are presented.

Significado empírico de la multifractalidad de la precipitación

El objetivo central de la presente investigación es profundizar la interpretación de los parámetros multifractales en el caso de las series de precipitación. Para ello se aborda, en primer lugar, la objetivación de la selección de la parte lineal de las curvas log-log que se encuentra en la base de los métodos de análisis fractal y multifractal; y, en segundo lugar, la generación de series artificiales de precipitación, con características similares a las reales, que permitan manipular los datos y evaluar la influencia de las modificaciones controladas de las series en los resultados de los parámetros multifractales derivados. En cuanto al problema de la selección de la parte lineal de las curvas log-log se desarrollaron dos métodos: a. Cambio de tendencia, que consiste en analizar el cambio de pendiente de las rectas ajustadas a dos subconjuntos consecutivos de los datos. b. Eliminación de casos, que analiza la mejora en el p-valor asociado al coeficiente de correlación al eliminar secuencialmente los puntos finales de la regresión. Los resultados obtenidos respecto a la regresión lineal establecen las siguientes conclusiones: - La metodología estadística de la regresión muestra la dificultad para encontrar el valor de la pendiente de tramos rectos de curvas en el procedimiento base del análisis fractal, indicando que la toma de decisión de los puntos a considerar redunda en diferencias significativas de las pendientes encontradas. - La utilización conjunta de los dos métodos propuestos ayuda a objetivar la toma de decisión sobre la parte lineal de las familias de curvas en el análisis fractal, pero su utilidad sigue dependiendo del número de datos de que se dispone y de las altas significaciones que se obtienen. En cuanto al significado empírico de los parámetros multifratales de la precipitación, se han generado 19 series de precipitación por medio de un simulador de datos diarios en cascada a partir de estimaciones anuales y mensuales, y en base a estadísticos reales de 4 estaciones meteorológicas españolas localizadas en un gradiente de NW a SE. Para todas las series generadas, se calculan los parámetros multifractales siguiendo la técnica de estimación de la DTM (Double Trace Moments - Momentos de Doble Traza) desarrollado por Lavalle et al. (1993) y se observan las modificaciones producidas. Los resultados obtenidos arrojaron las siguientes conclusiones: - La intermitencia, C1, aumenta al concentrar las precipitaciones en menos días, al hacerla más variable, o al incrementar su concentración en los días de máxima, mientras no se ve afectado por la modificación en la variabilidad del número de días de lluvia. - La multifractalidad, α, se ve incrementada con el número de días de lluvia y la variabilidad de la precipitación, tanto anual como mensual, así como también con la concentración de precipitación en el día de máxima. - La singularidad probable máxima, γs, se ve incrementada con la concentración de la lluvia en el día de precipitación máxima mensual y la variabilidad a nivel anual y mensual. - El grado no- conservativo, H, depende del número de los días de lluvia que aparezcan en la serie y secundariamente de la variabilidad general de la lluvia. - El índice de Hurst generalizado se halla muy ligado a la singularidad probable máxima. ABSTRACT The main objective of this research is to interpret the multifractal parameters in the case of precipitation series from an empirical approach. In order to do so the first proposed task was to objectify the selection of the linear part of the log-log curves that is a fundamental step of the fractal and multifractal analysis methods. A second task was to generate precipitation series, with real like features, which allow evaluating the influence of controlled series modifications on the values of the multifractal parameters estimated. Two methods are developed for selecting the linear part of the log-log curves in the fractal and multifractal analysis: A) Tendency change, which means analyzing the change in slope of the fitted lines to two consecutive subsets of data. B) Point elimination, which analyzes the improvement in the p- value associated to the coefficient of correlation when the final regression points are sequentially eliminated. The results indicate the following conclusions: - Statistical methodology of the regression shows the difficulty of finding the slope value of straight sections of curves in the base procedure of the fractal analysis, pointing that the decision on the points to be considered yield significant differences in slopes values. - The simultaneous use of the two proposed methods helps to objectify the decision about the lineal part of a family of curves in fractal analysis, but its usefulness are still depending on the number of data and the statistical significances obtained. Respect to the empiric meaning of the precipitation multifractal parameters, nineteen precipitation series were generated with a daily precipitation simulator derived from year and month estimations and considering statistics from actual data of four Spanish rain gauges located in a gradient from NW to SE. For all generated series the multifractal parameters were estimated following the technique DTM (Double Trace Moments) developed by Lavalle et al. (1993) and the variations produced considered. The results show the following conclusions: 1. The intermittency, C1, increases when precipitation is concentrating for fewer days, making it more variable, or when increasing its concentration on maximum monthly precipitation days, while it is not affected due to the modification in the variability in the number of days it rained. 2. Multifractility, α, increases with the number of rainy days and the variability of the precipitation, yearly as well as monthly, as well as with the concentration of precipitation on the maximum monthly precipitation day. 3. The maximum probable singularity, γs, increases with the concentration of rain on the day of the maximum monthly precipitation and the variability in yearly and monthly level. 4. The non-conservative degree, H’, depends on the number of rainy days that appear on the series and secondly on the general variability of the rain. 5. The general Hurst index is linked to the maximum probable singularity.

Do charges to freight trucks and trains in the European Union reflect their social marginal costs? Application to the case of Spain

In the last few years, the European Union (EU) has become greatly concerned about the environmental costs of road transport in Europe as a result of the constant growth in the market share of trucks and the steady decline in the market share of railroads. In order to reverse this trend, the EU is promoting the implementation of additional charges for heavy goods vehicles (HGV) on the trunk roads of the EU countries. However, the EU policy is being criticised because it does not address the implementation of charges to internalise the external costs produced by automobiles and other transport modes such as railroad. In this paper, we first describe the evolution of the HGV charging policy in the EU, and then assess its practical implementation across different European countries. Second, and of greater significance, by using the case study of Spain, we evaluate to what extent the current fees on trucks and trains reflect their social marginal costs, and consequently lead to an allocative-efficient outcome. We found that for the average case in Spain the truck industry meets more of the marginal social cost produced by it than does the freight railroad industry. The reason for this lies in the large sums of money paid by truck companies in fuel taxes, and the subsidies that continue to be granted by the government to the railroads.

Cobertura de la trinchera ferroviaria de Hendaya

Un problema del ferrocarril al paso por las ciudades europeas es el efecto barrera generado, que impide su desarrollo más allá de las vías. Si se salta la barrera lo cierto es que ello se hace sólo en sitios concretos y el efecto psicológico de aislamiento persiste para los habitantes del entorno. Este trabajo presenta de manera sucinta los problemas de concepción, comprobación y vibraciones planteados por la estructura de cubierta de la trinchera ferroviaria de Hendaya, consistente en una losa de hormigón pretensado y luz variable de 20-40 metros, que resuelve el problema de aislamiento entre las dos partes de la ciudad. Su construcción ha sido posible gracias al acuerdo entre la SNCF e inversores privados y está permitiendo la construcción sobre ella de 6 edificios de viviendas y una residencia de turismo, la demolición del antiguo ?Pont-Vieux? y la construcción de un nuevo ?Pont-Vieux?, integrado completamente en la promoción inmobiliaria. An important problem put by the train in its passage by the cities of Europe generally and in France in particular is the effect barrier which builds up, preventing the cities from developing beyond. Even if this barrier is crossed, it is certain that the passage is restricted to concrete places and always acts as psychological barrier for the local residents. This article presents in a brief way the problems of conception, analysis and vibration of the cover structure of the railroad trench of Hendaye. This structure consists of a 20-40 meters span slab of pre-stressed concrete that solves the isolation problem of both parts of the town of Hendaye. Its construction was possible thanks to the agreement of the SNCF (French Railways)and some private investors, and is allowing the investors the construction on top of 6 residential buildings and a holiday residence, with demolition of the ancient “Pont-Vieux” and building of a new “Pont-Vieux”, which is completely integrated into the real-estate development. Special attention is given to the change of transverse cross-section of the slab during construction stages, which originates a redistribution of stresses, and to the long-term equilibrium of horizontal forces.

Risk assessment of the spanish national railway system

The principal risks in the railway industry are mainly associated with collisions, derailments and level crossing accidents. An understanding of the nature of previous accidents on the railway network is required to identify potential causes and develop safety systems and deploy safety procedures. Risk assessment is a process for determining the risk magnitude to assist with decision-making. We propose a three-step methodology to predict the mean number of fatalities in railway accidents. The first is to predict the mean number of accidents by analyzing generalized linear models and selecting the one that best fits to the available historical data on the basis of goodness-offit statistics. The second is to compute the mean number of fatalities per accident and the third is to estimate the mean number of fatalities. The methodology is illustrated on the Spanish railway system. Statistical models accounting for annual and grouped data for the 1992-2009 time period have been analyzed. After identifying the models for broad and narrow gauges, we predicted mean number of accidents and the number of fatalities for the 2010-18 time period.

Offshore Measurements of Ocean Waves using Stereo Vision Systems

In recent years, remote sensing imaging systems for the measurement of oceanic sea states have attracted renovated attention. Imaging technology is economical, non-invasive and enables a better understanding of the space-time dynamics of ocean waves over an area rather than at selected point locations of previous monitoring methods (buoys, wave gauges, etc.). We present recent progress in space-time measurement of ocean waves using stereo vision systems on offshore platforms, which focus on sea states with wavelengths in the range of 0.01 m to 10 m. Classical epipolar techniques and modern variational methods are reviewed to reconstruct the sea surface from the stereo pairs sequentially in time. The statistical and spectral properties of the resulting observed waves are analyzed. Current improvements of the variational methods are discussed as future lines of research.

Análisis de micromovilidad en vástagos femorales mediante ensayo dinámico de oscilaciones libres

La artroplastia de cadera se considera uno de los mayores avances quirúrgicos de la Medicina. La aplicación de esta técnica de Traumatología se ha incrementado notablemente en los últimos anos, a causa principalmente del progresivo incremento de la esperanza de vida. En efecto, con la edad aumentan los problemas de artrosis y osteoporosis, enfermedades típicas de las articulaciones y de los huesos que requieren en muchos casos la sustitución protésica total o parcial de la articulación. El buen comportamiento funcional de una prótesis depende en gran medida de la estabilidad primaria, es decir, el correcto anclaje de la prótesis en el momento de su implantación. Las prótesis no cementadas basan su éxito a largo plazo en la osteointegración que tiene lugar entre el material protésico y el tejido óseo, y para lograrla es imprescindible conseguir unas buenas condiciones de estabilidad primaria. El aflojamiento aséptico es la principal causa de fallo de artroplastia total de cadera. Este es un fenómeno en el que, debido a complejas interacciones de factores mecánicos y biológicos, se producen movimientos relativos que comprometen la funcionalidad del implante. La minimización de los correspondientes danos depende en gran medida de la detección precoz del aflojamiento. Para lograr la detección temprana del aflojamiento aséptico del vástago femoral se han ensayado diferentes técnicas, tanto in vivo como in vitro: análisis numéricos y técnicas experimentales basadas en sensores de movimientos provocados por cargas transmitidas natural o artificialmente, tales como impactos o vibraciones de distintas frecuencias. Los montajes y procedimientos aplicados son heterogéneos y, en muchas ocasiones, complejos y costosos, no existiendo acuerdo sobre una técnica simple y eficaz de aplicación general. Asimismo, en la normativa vigente que regula las condiciones que debe cumplir una prótesis previamente a su comercialización, no hay ningún apartado referido específicamente a la evaluación de la bondad del diseño del vástago femoral con respecto a la estabilidad primaria. El objetivo de esta tesis es desarrollar una metodología para el análisis, in vitro, de la estabilidad de un vástago femoral implantado, a fin de poder evaluar las técnicas de implantación y los diferentes diseños de prótesis previamente a su oferta en el mercado. Además se plantea como requisito fundamental que el método desarrollado sea sencillo, reversible, repetible, no destructivo, con control riguroso de parámetros (condiciones de contorno de cargas y desplazamientos) y con un sistema de registro e interpretación de resultados rápido, fiable y asequible. Como paso previo, se ha realizado un análisis cualitativo del problema de contacto en la interfaz hueso-vástago aplicando una técnica optomecánica del campo continuo (fotoelasticidad). Para ello se han fabricado tres modelos en 2D del conjunto hueso-vástago, simulando tres tipos de contactos en la interfaz: contacto sin adherencia y con holgura, contacto sin adherencia y sin holgura, y contacto con adherencia y homogéneo. Aplicando la misma carga a cada modelo, y empleando la técnica de congelación de tensiones, se han visualizado los correspondientes estados tensionales, siendo estos más severos en el modelo de unión sin adherencia, como cabía esperar. En todo caso, los resultados son ilustrativos de la complejidad del problema de contacto y confirman la conveniencia y necesidad de la vía experimental para el estudio del problema. Seguidamente se ha planteado un ensayo dinámico de oscilaciones libres con instrumentación de sensores resistivos tipo galga extensométrica. Las muestras de ensayo han sido huesos fémur en todas sus posibles variantes: modelos simplificados, hueso sintético normalizado y hueso de cadáver, seco y fresco. Se ha diseñado un sistema de empotramiento del extremo distal de la muestra (fémur) con control riguroso de las condiciones de anclaje. La oscilación libre de la muestra se ha obtenido mediante la liberación instantánea de una carga estética determinada y aplicada previamente, bien con una maquina de ensayo o bien por gravedad. Cada muestra se ha instrumentado con galgas extensométricas convencionales cuya señal se ha registrado con un equipo dinámico comercial. Se ha aplicado un procedimiento de tratamiento de señal para acotar, filtrar y presentar las respuestas de los sensores en el dominio del tiempo y de la frecuencia. La interpretación de resultados es de tipo comparativo: se aplica el ensayo a una muestra de fémur Intacto que se toma de referencia, y a continuación se repite el ensayo sobre la misma muestra con una prótesis implantada; la comparación de resultados permite establecer conclusiones inmediatas sobre los efectos de la implantación de la prótesis. La implantación ha sido realizada por un cirujano traumatólogo utilizando las mismas técnicas e instrumental empleadas en el quirófano durante la práctica clínica real, y se ha trabajado con tres vástagos femorales comerciales. Con los resultados en el dominio del tiempo y de la frecuencia de las distintas aplicaciones se han establecido conclusiones sobre los siguientes aspectos: Viabilidad de los distintos tipos de muestras sintéticas: modelos simplificados y fémur sintético normalizado. Repetibilidad, linealidad y reversibilidad del ensayo. Congruencia de resultados con los valores teóricos deducidos de la teoría de oscilaciones libres de barras. Efectos de la implantación de tallos femorales en la amplitud de las oscilaciones, amortiguamiento y frecuencias de oscilación. Detección de armónicos asociados a la micromovilidad. La metodología se ha demostrado apta para ser incorporada a la normativa de prótesis, es de aplicación universal y abre vías para el análisis de la detección y caracterización de la micromovilidad de una prótesis frente a las cargas de servicio. ABSTRACT Total hip arthroplasty is considered as one of the greatest surgical advances in medicine. The application of this technique on Traumatology has increased significantly in recent years, mainly due to the progressive increase in life expectancy. In fact, advanced age increases osteoarthritis and osteoporosis problems, which are typical diseases of joints and bones, and in many cases require full or partial prosthetic replacement on the joint. Right functional behavior of prosthesis is highly dependent on the primary stability; this means it depends on the correct anchoring of the prosthesis at the time of implantation. Uncemented prosthesis base their long-term success on the quality of osseointegration that takes place between the prosthetic material and bone tissue, and to achieve this good primary stability conditions is mandatory. Aseptic loosening is the main cause of failure in total hip arthroplasty. This is a phenomenon in which relative movements occur, due to complex interactions of mechanical and biological factors, and these micromovements put the implant functionality at risk. To minimize possible damage, it greatly depends on the early detection of loosening. For this purpose, various techniques have been tested both in vivo and in vitro: numerical analysis and experimental techniques based on sensors for movements caused by naturally or artificially transmitted loads, such as impacts or vibrations at different frequencies. The assemblies and methods applied are heterogeneous and, in many cases, they are complex and expensive, with no agreement on the use of a simple and effective technique for general purposes. Likewise, in current regulations for governing the conditions to be fulfilled by the prosthesis before going to market, there is no specific section related to the evaluation of the femoral stem design in relation to primary stability. The aim of this thesis is to develop a in vitro methodology for analyzing the stability of an implanted femoral stem, in order to assess the implantation techniques and the different prosthesis designs prior to its offer in the market. We also propose as a fundamental requirement that the developed testing method should be simple, reversible, repeatable, non-destructive, with close monitoring of parameters (boundary conditions of loads and displacements) and with the availability of a register system to record and interpret results in a fast, reliable and affordable manner. As a preliminary step, we have performed a qualitative analysis of the contact problems in the bone-stem interface, through the application of a continuous field optomechanical technique (photoelasticity). For this proposal three 2D models of bone–stem set, has been built simulating three interface contact types: loosened an unbounded contact, unbounded and fixed contact, and bounded homogeneous contact. By means of applying the same load to each model, and using the stress freezing technique, it has displayed the corresponding stress states, being more severe as expected, in the unbounded union model. In any case, the results clearly show the complexity of the interface contact problem, and they confirm the need for experimental studies about this problem. Afterward a free oscillation dynamic test has been done using resistive strain gauge sensors. Test samples have been femur bones in all possible variants: simplified models, standardized synthetic bone, and dry and cool cadaveric bones. An embedding system at the distal end of the sample with strong control of the anchoring conditions has been designed. The free oscillation of the sample has been obtained by the instantaneous release of a static load, which was previously determined and applied to the sample through a testing machine or using the gravity force. Each sample was equipped with conventional strain gauges whose signal is registered with a marketed dynamic equipment. Then, it has applied a signal processing procedure to delimit, filter and present the time and frequency response signals from the sensors. Results are interpreted by comparing different trials: the test is applied to an intact femur sample which is taken as a reference, and then this test is repeated over the same sample with an implanted prosthesis. From comparison between results, immediate conclusions about the effects of the implantation of the prosthesis can be obtained. It must be said that the implementation has been made by an expert orthopedic surgeon using the same techniques and instruments as those used in clinical surgery. He has worked with three commercial femoral stems. From the results obtained in the time and frequency domains for the different applications the following conclusions have been established: Feasibility of the different types of synthetic samples: simplified models and standardized synthetic femur. Repeatability, linearity and reversibility of the testing method. Consistency of results with theoretical values deduced from the bars free oscillations theory. Effects of introduction of femoral stems in the amplitude, damping and frequencies of oscillations Detection of micromobility associated harmonics. This methodology has been proved suitable to be included in the standardization process of arthroplasty prosthesis, it is universally applicable and it allows establishing new methods for the analysis, detection and characterization of prosthesis micromobility due to functional loads.

Offshore remote sensing of the ocean by stereo vision systems

In recent years, remote sensing imaging systems for the measurement of oceanic sea states have attracted renovated attention. Imaging technology is economical, non-invasive and enables a better understanding of the space-time dynamics of ocean waves over an area rather than at selected point locations of previous monitoring methods (buoys, wave gauges, etc.). We present recent progress in space-time measurement of ocean waves using stereo vision systems on offshore platforms, which focus on sea states with wavelengths in the range of 0.01 m to 1 m. Both traditional disparity-based systems and modern elevation-based ones are presented in a variational optimization framework: the main idea is to pose the stereoscopic reconstruction problem of the surface of the ocean in a variational setting and design an energy functional whose minimizer is the desired temporal sequence of wave heights. The functional combines photometric observations as well as spatial and temporal smoothness priors. Disparity methods estimate the disparity between images as an intermediate step toward retrieving the depth of the waves with respect to the cameras, whereas elevation methods estimate the ocean surface displacements directly in 3-D space. Both techniques are used to measure ocean waves from real data collected at offshore platforms in the Black Sea (Crimean Peninsula, Ukraine) and the Northern Adriatic Sea (Venice coast, Italy). Then, the statistical and spectral properties of the resulting observed waves are analyzed. We show the advantages and disadvantages of the presented stereo vision systems and discuss future lines of research to improve their performance in critical issues such as the robustness of the camera calibration in spite of undesired variations of the camera parameters or the processing time that it takes to retrieve ocean wave measurements from the stereo videos, which are very large datasets that need to be processed efficiently to be of practical usage. Multiresolution and short-time approaches would improve efficiency and scalability of the techniques so that wave displacements are obtained in feasible times.

Space-time ocean wave measurement using variational stereo vision systems

Remote sensing imaging systems for the measurement of oceanic sea states have recently attracted renovated attention. Imaging technology is economical, non-invasive and enables a better understanding of the space-time dynamics of ocean waves over an area rather than at selected point locations of previous monitoring methods (buoys, wave gauges, etc.). We present recent progress in space-time measurement of ocean waves using stereo vision systems on offshore platforms. Both traditional disparity-based systems and modern elevation-based ones are presented in a variational optimization framework: the main idea is to pose the stereoscopic reconstruction problem of the surface of the ocean in a variational setting and design an energy functional whose minimizer is the desired temporal sequence of wave heights. The functional combines photometric observations as well as spatial and temporal smoothness priors. Disparity methods estimate the disparity between images as an intermediate step toward retrieving the depth of the waves with respect to the cameras, whereas elevation methods estimate the ocean surface displacements directly in 3-D space. Both techniques are used to measure ocean waves from real data collected at offshore platforms in the Black Sea (Crimean Peninsula, Ukraine) and the Northern Adriatic Sea (Venice coast, Italy). Then, the statistical and spectral properties of the resulting observed waves are analyzed. We show the advantages and disadvantages of the presented stereo vision systems and discuss the improvement of their performance in critical issues such as the robustness of the camera calibration in spite of undesired variations of the camera parameters.

Aeroacoustics in high speed trains

Este trabajo se centra en el estudio de problemas aeroacústicos en los trenes de alta velocidad. Se han considerado dos escenarios en los que las ondas de presión generadas son críticos para el confort de los pasajeros. Uno es el debido a las ondas de presión que genera el tren cuando entra y sale de un túnel, que a su vez producen saltos de presión de baja frecuencia en el tren (cuando se cruzan con él) y en los alrededores del túnel cuando alcanzan la salida. Se estudia este fenómeno, y se propone un sistema aeroelástico basado en el galope transversal para disminuir la energía de estas ondas, y se analiza la energía extraíble de las ondas utilizando cuerpos con diferentes secciones transversales [Sorribes-Palmer and Sanz-Andres, 2013]. La influencia de la geometría de los portales en la energía radiada hacia el exterior de túnel es analizada experimentalmente, prestando especial atención a las boquillas porosas. Las ondas de presión en el interior del túnel se han analizado mediante el método de las características. Se han realizado ensayos experimentales para estimar la energía reflejada hacia el interior del túnel al alcanzar las ondas de presión el portal de salida del túnel. Se ha estudiado la formación e interacción entre el portal del túnel y la onda de choque generada en los túneles de gran longitud y pequeña fricción. Se propone un método para describir de forma aproximada el ruido radiado al exterior. Por otro lado se ha estudiado el ruido de media y alta frecuencia de origen aerodinámico. Se ha estudiado la influencia del desprendimiento de la capa límite sobre el tren. Se propone una metodología basada en una sección de tren característica para predecir rápidamente el nivel de presión de sonido dentro y fuera del tren para todo el rango de frecuencias. Se han realizado medidas experimentales en vía de los espectros de presión sobre la superficie del tren, y de la transmisibilidad de las uniones entre estructura y revestimiento. Los resultados experimentales se han utilizado en los modelos vibroacústicos. El método de la sección del tren característica es especialmente útil a altas frecuencias cuando todo el tren se puede modelar mediante el ensamblaje de diferentes secciones características utilizando el análisis estadístico de la energía. ABSTRACT This work is focused on the study of aeroacoustic problems in high speed trains. We have considered two scenarios in which the pressure waves generated are critical for passengers comfort. The first one is due to the pressure waves generated by a train entering in a tunnel. These waves generate pressure gauges inside the train (when they find each other) and outside of the tunnel portals. This phenomenon has been studied, and an aeroelastic system based on transverse galloping to reduce the energy of these waves is proposed. The maximum extractable energy by using bodies with different cross-section shapes is analyzed. The influence of the portals geometry in the energy radiated outwards the tunnel is analyzed experimentally, with particular attention to the porous exits. The pressure waves inside the tunnel have been analyzed using the method of characteristics. Experimental tests to estimate the energy reflected into the tunnel when the pressure waves reach the tunnel portal have been performed. We have studied the generation and interaction between the tunnel portal and a shock wave generated in long tunnels with small friction. A method to describe in an approximated way the pressure radiated outside the tunnel is proposed. In the second scenario, middle and high frequency noise generated aerodynamically has been studied, including the influence of the detachment of the boundary layer around the train. A method based on a train section to quickly predict the sound pressure level inside and outside the train has been proposed. Experimental test have been performed on board to evaluate the pressure power spectra on the surface of the train, and the transmissibility of the junctions between the structure and trim. These experimental results have been used in the vibroacoustic models. The low frequency pressure waves generated with the train during the tunnel crossing has been identified in the pressure spectrum. The train characteristic section method is especially useful at high frequencies, when the whole train can be modeled by assembling different sections using the statistical energy analysis. The sound pressure level inside the train is evaluated inside and outside the tunnel.

A novel method for measuring the dynamic fracture-initiation toughness under impulsive loadings

The design and development of a new method for performing fracture toughness tests under impulsive loadings using explosives is presented. The experimental set-up was complemented with pressure transducers and strain gauges in order to measure, respectively, the blast wave that reached the specimen and the loading history. Fracture toughness tests on a 7017-T73 aluminium alloy were carried out by using this device under impulsive loadings. Previous studies reported that such aluminium alloy had very little strain rate sensitivity, which made it an ideal candidate for comparison at different loading rates. The fracture-initiation toughness values of the 7017-T73 aluminium alloy obtained at impulsive loadings did not exhibit a significant variation from the cases studied at lower loading rates. Therefore, the method and device developed for measuring the dynamic fracture-initiation toughness under impulsive loadings was considered suitable for such a purpose

La Península Ibérica en el transporte masivo de mercancías entre Europa y África : futuras autopistas del mar

La competitividad del transporte de mercancías depende del estado y funcionamiento de las redes existentes y de sus infraestructuras, no del modo de transporte. En concreto, la rentabilidad o la reducción de los costes de producción del transporte marítimo se vería incrementado con el uso de buques de mayor capacidad y con el desarrollo de plataformas portuarias de distribución o puertos secos, ya que el 90% del comercio entre la Unión Europea y terceros países se realiza a través de sus puertos a un promedio de 3,2 billones de toneladas de mercancías manipuladas cada año y el 40% del tráfico intraeuropeo utiliza el transporte marítimo de corta distancia. A pesar de que los puertos europeos acogen anualmente a más de 400 millones de pasajeros, los grandes desarrollos se han producido en los puertos del norte de Europa (Róterdam, Amberes, Ámsterdam). Los países del Sur de Europa deben buscar nuevas fórmulas para ser más competitivos, ya sea mediante creación de nuevas infraestructuras o mediante refuerzo de las existentes, ofreciendo los costes de los puertos del Norte. El fomento del transporte marítimo y fluvial como alternativa al transporte por carretera, especialmente el transporte marítimo de corta distancia, ha sido impulsado por la Comisión Europea (CE) desde 2003 a través de programas de apoyo comunitario de aplicación directa a las Autopistas del Mar, a modo de ejemplo, cabría citar los programas Marco Polo I y II, los cuales contaron con una dotación presupuestaria total de 855 millones de euros para el período 2003 – 2013; en ese período de tiempo se establecieron objetivos de reducción de congestión vial y mejora del comportamiento medio ambiental del sistema de transporte de mercancías dentro de la comunidad y la potenciación de la intermodalidad. El concepto de Autopista del Mar surge en el Libro Blanco de Transportes de la Comisión Europea “La política europea de transportes de cara al 2010: La hora de la verdad” del 12 de diciembre de 2001, en el marco de una política europea para fomento y desarrollo de sistemas de transportes sostenibles. Las Autopistas del Mar consisten en rutas marítimas de corta distancia entre dos puntos, de menor distancia que por vía terrestre, en las que a través del transporte intermodal mejoran significativamente los tiempos y costes de la cadena logística, contribuyen a la reducción de accidentes, ruidos y emisiones de CO2 a la atmósfera, permite que los conductores pierdan horas de trabajo al volante y evita el deterioro de las infraestructuras terrestres, con el consiguiente ahorro en mantenimiento. La viabilidad de una Autopista del Mar depende tanto de factores de ubicación geográficos, como de características propias del puerto, pasando por los diferentes requerimientos del mercado en cada momento (energéticos, medio ambientales y tecnológicos). Existe un elemento nuevo creado por la Comisión Europea: la red transeuropea de transportes (RTE-T). En el caso de España, con sus dos accesos por los Pirineos (La Junquera e Irún) como únicos pasos terrestres de comunicación con el continente y con importantes limitaciones ferroviarias debido a los tres anchos de vía distintos, le resta competitividad frente al conjunto europeo; por el contrario, España es el país europeo con más kilómetros de costa (con más de 8.000 km) y con un emplazamiento geográfico estratégico, lo que le convierte en una plataforma logística para todo el sur de Europa, por lo que las Autopistas del Mar tendrán un papel importante y casi obligado para el desarrollo de los grandes corredores marítimos que promueve Europa. De hecho, Gijón y Vigo lo han hecho muy bien con sus respectivas líneas definidas como Autopistas del Mar y que conectan con el puerto francés de Nantes-Saint Nazaire, ya que desde ahí los camiones pueden coger rutas hacia el Norte. Paralelamente, la Unión Europea ha iniciado los pasos para el impulso de la primera Autopista del Mar que conectará España con el mercado de Reino Unido, concretamente los Puertos de Bilbao y Tilbury. Además, España e Italia sellaron un acuerdo internacional para desarrollar Autopistas del Mar entre ambos países, comprometiéndose a impulsar una docena de rutas entre puertos del litoral mediterráneo español y el italiano. Actualmente, están en funcionando los trayectos como Barcelona-Génova, Valencia-Civitavecchia y Alicante- Nápoles, notablemente más cortos por mar que por carretera. Bruselas identificó cuatro grandes corredores marítimos que podrían concentrar una alta densidad de tráfico de buques, y en dos de ellos España ya tenía desde un principio un papel crucial. La Comisión diseñó el 14 de abril de 2004, a través del proyecto West-Mos, una red de tráfico marítimo que tiene como vías fundamentales la denominada Autopista del Báltico (que enlaza Europa central y occidental con los países bálticos), la Autopista de Europa suroriental (que une el Adriático con el Jónico y el Mediterráneo más oriental) y también la Autopista de Europa occidental y la Autopista de Europa suroccidental (que enlazan España con Reino Unido y la Francia atlántica y con la Francia mediterránea e Italia, respectivamente). Para poder establecer Autopistas del Mar entre la Península Ibérica y el Norte de Europa primará especialmente la retirada de camiones en la frontera pirenaica, donde el tráfico pesado tiene actualmente una intensidad media diaria de 8.000 unidades, actuando sobre los puntos de mayor congestión, como por ejemplo los Alpes, los Pirineos, el Canal de la Mancha, las carreteras fronterizas de Francia y Euskadi, y proponiendo el traslado de las mercancías en barcos o en trenes. Por su parte, para contar con los subsidios y apoyos europeos las rutas seleccionadas como Autopistas del Mar deben mantener una serie de criterios de calidad relacionados con la frecuencia, coste “plataforma logística a plataforma logística”, simplicidad en procedimientos administrativos y participación de varios países, entre otros. Los estudios consideran inicialmente viables los tramos marítimos superiores a 450 millas, con un volumen de unas 15.000 plataformas al año y que dispongan de eficientes comunicaciones desde el puerto a las redes transeuropeas de autopistas y ferrocarril. Otro objetivo de las Autopistas del Mar es desarrollar las capacidades portuarias de forma que se puedan conectar mejor las regiones periféricas a escala del continente europeo. En lo que a Puertos se refiere, las terminales en los muelles deben contar con una línea de atraque de 250 m., un calado superior a 8 m., una rampa “ro-ro” de doble calzada, grúas portainer, y garantizar operatividad para un mínimo de dos frecuencias de carga semanales. El 28 de marzo de 2011 se publicó el segundo Libro Blanco sobre el futuro del transporte en Europa “Hoja de ruta hacia un espacio único europeo de transporte: por una política de transportes competitiva y sostenible”, donde se definió el marco general de las acciones a emprender en los próximos diez años en el ámbito de las infraestructuras de transporte, la legislación del mercado interior, la reducción de la dependencia del carbono, la tecnología para la gestión del tráfico y los vehículos limpios, así como la estandarización de los distintos mercados. Entre los principales desafíos se encuentran la eliminación de los cuellos de botella y obstáculos diversos de nuestra red europea de transporte, minimizar la dependencia del petróleo, reducir las emisiones de GEI en un 60% para 2050 con respecto a los niveles de 1990 y la inversión en nuevas tecnologías e infraestructuras que reduzcan estas emisiones de transporte en la UE. La conexión entre la UE y el norte de África provoca elevados niveles de congestión en los puntos más críticos del trayecto: frontera hispano-francesa, corredor del Mediterráneo y el paso del estrecho. A esto se le añade el hecho de que el sector del transporte por carretera está sujeto a una creciente competencia de mercado motivada por la eliminación de las barreras europeas, mayores exigencias de los cargadores, mayores restricciones a los conductores y aumento del precio del gasóleo. Por otro lado, el mercado potencial de pasajeros tiene una clara diferenciación en tipos de flujos: los flujos en el período extraordinario de la Operación Paso del Estrecho (OPE), enfocado principalmente a marroquíes que vuelven a su país de vacaciones; y los flujos en el período ordinario, enfocado a la movilidad global de la población. Por tanto, lo que se pretende conseguir con este estudio es analizar la situación actual del tráfico de mercancías y pasajeros con origen o destino la península ibérica y sus causas, así como la investigación de las ventajas de la creación de una conexión marítima (Autopista del Mar) con el Norte de África, basándose en los condicionantes técnicos, administrativos, económicos, políticos, sociales y medio ambientales. The competitiveness of freight transport depends on the condition and operation of existing networks and infrastructure, not the mode of transport. In particular, profitability could be increased or production costs of maritime transport could be reduced by using vessels with greater capacity and developing port distribution platforms or dry ports, seeing as 90% of trade between the European Union and third countries happens through its ports. On average 3,2 billion tonnes of freight are handled annualy and 40% of intra-European traffic uses Short Sea Shipping. In spite of European ports annually hosting more than 400 million passengers, there have been major developments in the northern European ports (Rotterdam, Antwerp, Amsterdam). Southern European countries need to find new ways to be more competitive, either by building new infrastructure or by strengthening existing infrastructure, offering costs northern ports. The use of maritime and river transport as an alternative to road transport, especially Short Sea Shipping, has been driven by the European Commission (EC) from 2003 through community support programs for the Motorways of the Sea. These programs include, for example, the Marco Polo I and II programs, which had a total budget of 855 million euros for the period 2003-2013. During this time objectives were set for reducing road congestion, improving the environmental performance of the freight transport system within the community and enhancing intermodal transport. The “Motorway of the Sea” concept arises in the European Commission’s Transport White Paper "European transport policy for 2010: time to decide" on 12 December 2001, as part of a European policy for the development and promotion of sustainable transport systems. A Motorway of the Sea is defined as a short sea route between two points, covering less distance than by road, which provides a significant improvement in intermodal transport times and to the cost supply chain. It contributes to reducing accidents, noise and CO2 emissions, allows drivers to shorten their driving time and prevents the deterioration of land infrastructure thereby saving on maintenance costs. The viability of a Motorway of the Sea depends as much on geographical location factors as on characteristics of the port, taking into account the different market requirements at all times (energy, environmental and technological). There is a new element created by the European Commission: the trans-European transport network (TEN-T). In the case of Spain, with its two access points in the Pyrenees (La Junquera and Irun) as the only land crossings connected to the mainland and major railway limitations due to the three different gauges, it appears less competitive compared to Europe as a whole. However, Spain is the European country with the most kilometers of coastline (over 8,000 km) and a strategic geographical location, which makes it a logistics platform for the all of Southern Europe. This is why the Motorways of the Sea will have an important role, and an almost necessary one to develop major maritime corridors that Europe supports. In fact, Gijon and Vigo have done very well with their respective sea lanes defined as Motorways of the Sea and which connect with the French port of Nantes-Saint Nazaire, as from there trucks can use nort-heading routes. In parallel, the European Union has taken the first steps to boost the first Motorway of the Sea linking Spain to the UK market, specifically the ports of Bilbao and Tilbury. Furthermore, Spain and Italy sealed an international agreement to develop Motorways of the Sea between both countries, pledging to develop a dozen routes between ports on the Spanish and Italian Mediterranean coasts. Currently, there are sea lanes already in use such as Barcelona-Genova, Valencia-Civitavecchia and Alicante-Naples, these are significantly shorter routes by sea than by road. Brussels identified four major maritime corridors that could hold heavy concentrate shipping traffic, and Spain had a crucial role in two of these from the beginning. On 14 April 2004 the Commission planned through the West-Mos project, a network of maritime traffic which includes the essential sea passages the so-called Baltic Motorway (linking Central and Western Europe with the Baltic countries), the southeast Europe Motorway (linking the Adriatic to the Ionian and eastern Mediterranean Sea), the Western Europe Motorway and southwestern Europe Motorway (that links Spain with Britain and the Atlantic coast of France and with the French Mediterranean coast and Italy, respectively). In order to establish Motorways of the Sea between the Iberian Peninsula and Northern Europe especially, it is necessary to remove trucks from the Pyrenean border, where sees heavy traffic (on average 8000 trucks per day) and addressing the points of greatest congestion, such as the Alps, the Pyrenees, the English Channel, the border roads of France and Euskadi, and proposing the transfer of freight on ships or trains. For its part, in order to receive subsidies and support from the European Commission, the routes selected as Motorways of the Sea should maintain a series of quality criteria related to frequency, costs "from logistics platform to logistics platform," simplicity in administrative procedures and participation of several countries, among others. To begin with, studies consider viable a maritime stretch of at least 450 miles with a volume of about 15,000 platforms per year and that have efficient connections from port to trans-European motorways and rail networks. Another objective of the Motorways of the Sea is to develop port capacity so that they can better connect peripheral regions across the European continent. Referring ports, the terminals at the docks must have a berthing line of 250 m., a draft greater than 8 m, a dual carriageway "ro-ro" ramp, portainer cranes, and ensure operability for a minimum of two loads per week. On 28 March 2011 the second White Paper about the future of transport in Europe "Roadmap to a Single European Transport Area – Towards a competitive and resource efficient transport system" was published. In this Paper the general framework of actions to be undertaken in the next ten years in the field of transport infrastructure was defined, including internal market legislation, reduction of carbon dependency, traffic management technology and clean vehicles, as well as the standardization of different markets. The main challenges are how to eliminate bottlenecks and various obstacles in our European transport network, minimize dependence on oil, reduce GHG emissions by 60% by 2050 compared to 1990 levels and encourage investment in new technologies and infrastructure that reduce EU transport emissions. The connection between the EU and North Africa causes high levels of congestion on the most critical points of the journey: the Spanish-French border, the Mediterranean corridor and Gibraltar Strait. In addition to this, the road transport sector is subject to increased market competition motivated by the elimination of European barriers, greater demands of shippers, greater restrictions on drivers and an increase in the price of diesel. On the other hand, the potential passenger market has a clear differentiation in type of flows: flows in the special period of the Crossing the Straits Operation (CSO), mainly focused on Moroccans who return home on vacation; and flows in the regular session, focused on the global mobile population. Therefore, what I want to achieve with this study is present an analysis of the current situation of freight and passengers to or from the Iberian Peninsula and their causes, as well as present research on the advantages of creating a maritime connection (Motorways of the Sea) with North Africa, based on the technical, administrative, economic, political, social and environmental conditions.