Impact radiologique liés au transport de matières radioactives par route en Espagne / Radiological impact associated with the transport by road of radioactive material in Spain

Questions relating to the transport of radioactive materials are very much an issue of current interest due to the increasing mobility of the materials involved in the nuclear fuel cycle, commitment to the environment, the safety and protection of persons and the corresponding regulatory legal framework. The radiological impact associated with this type of transport was assessed by means of a new data-processing tool that may be of use and serve as complementary documentation to that included in transport regulations. Thus, by determining the level of radiation at a distance of one metre from the transport vehicle and by selecting a route, the associated impacts will be obtained, such as the affected populations, the dose received by the most highly exposed individual, the overall radiological impact, the doses received by the population along the route and the possible detriment to their health. The most important conclusion is that the emissions of ionising radiation from the transport of radioactive material by road in Spain are not significant as regards the generation of adverse effects on human health, and that their radiological impact may be considered negligible.

¿Impact from road transport of radioactive wastes in Spain?

Transports of radioactive wastes in Spain are becoming issues of renewed interest, due to the increased mobility of these materials which can be expected after the building and operation of the planned central repository for this country in a near future. Such types of residues will be mainly of the medium and high activity classes and have raised concerns on the safety of the operations, the radiological protection of the individuals, the compliance with the legal regulations and their environmental consequences of all kind. In this study, relevant information for the assessment of radiological risk of road transport were taken into account, as the sources and destination of the radioactive transports, the amount of traveling to be done, the preferred routes and populations affected, the characterization of the residues and containers, their corresponding testing, etc. These data were supplied by different organizations fully related with these activities, like the nuclear power stations, the companies in charge of radioactive transports, the enterprises for inspection and control of the activities, etc., as well as the government institutions which are responsible for the selection and location of the storage facility and other decisions on the nuclear policies of the country. Thus, we have developed a program for computing the data in such a form that by entering the radiation levels at one meter of the transport loads and by choosing a particular displacement, the computer application is capable to calculate the corresponding radiological effects, like the global estimated impact, its relevance to the population in general or on those people living and driving near the main road routes, the doses received by the most exposed individuals (e.g. the workers for loading or driving the vehicle), or the probability of detrimental on the human health. The results of this work could be of help for a better understanding and management of these activities and their related impacts; at the same time that the generated reports of the computer application are considered of particular interest as innovative and complementary information to the current legal documentation, which is basically required for transporting radioactive wastes in the country, according with the international safety rules (like IAEA and ADR).Though main studies are still in progress, as the definite location for the Spanish storage facility has not been decided yet, preliminary results with the existing transports of residues of medium activity indicate that the radiological impact is very low in conventional operations. Nevertheless, the management of these transports is complex and laborious, making it convenient to progress further in the analysis and quantification of this kind of events, which constitutes one of the main objectives of the present study for the radioactive road mobility in Spain.

El microclima urbano en los espacios abiertos : estudio de casos en Madrid

El microclima urbano juega un rol importante en el consumo energético de los edificios y en las sensaciones de confort en los espacios exteriores. La urgente necesidad de aumentar la eficiencia energética, reducir las emisiones de los contaminantes y paliar la evidente falta de sostenibilidad que afecta a las ciudades, ha puesto la atención en el urbanismo bioclimático como referente para una propuesta de cambio en la forma de diseñar y vivir la ciudad. Hasta ahora las investigaciones en temas de microclima y eficiencia energética se han concentrado principalmente en como orientar el diseño de nuevos desarrollo. Sin embargo los principales problemas de la insostenibilidad de las actuales conurbaciones son el resultado del modelo de crecimiento especulativo y altamente agotador de recursos que han caracterizado el boom inmobiliario de las últimas décadas. Vemos entonces, tanto en España como en el resto de los Países Europeos, la necesidad de reorientar el sector de la construcción hacía la rehabilitación del espacio construido, como una alternativa capaz de dar una solución más sostenible para el mercado inmobiliario. En este propósito de mejorar la calidad de las ciudades actuales, el espacio público juega un papel fundamental, sobre todo como lugar para el encuentro y la socialización entre los ciudadanos. La sensación térmica condiciona la percepción de un ambiente, así que el microclima puede ser determinante para el éxito o el fracaso de un espacio urbano. Se plantea entonces cómo principal objetivo de la investigación, la definición de estrategias para el diseño bioclimático de los entornos urbanos construidos, fundamentados en las componentes morfotipológica, climática y de los requerimientos de confort para los ciudadanos. Como ulterior elemento de novedad se decide estudiar la rehabilitación de los barrios de construcción de mediado del siglo XX, que en muchos casos constituyen bolsas de degrado en la extendida periferia de las ciudades modernas. La metodología empleada para la investigación se basa en la evaluación de las condiciones climáticas y de confort térmico de diferentes escenarios de proyecto, aplicados a tres casos de estudio situados en un barrio periurbano de la ciudad de Madrid. Para la determinación de los parámetros climáticos se han empleado valores obtenidos con un proceso de simulación computarizada, basados en los principios de fluidodinámica, termodinámica y del intercambio radioactivo en el espacio construido. A través de uso de programas de simulación podemos hacer una previsión de las condiciones microclimáticas de las situaciones actuales y de los efectos de la aplicación de medidas. La gran ventaja en el uso de sistemas de cálculo es que se pueden evaluar diferentes escenarios de proyecto y elegir entre ellos el que asegura mejores prestaciones ambientales. Los resultados obtenidos en los diferentes escenarios han sido comparados con los valores de confort del estado actual, utilizando como indicador de la sensación térmica el índice UTCI. El análisis comparativo ha permitido la realización de una tabla de resumen donde se muestra la evaluación de las diferentes soluciones de rehabilitación. Se ha podido así demostrar que no existe una solución constructiva eficaz para todas las aplicaciones, sino que cada situación debe ser estudiada individualmente, aplicando caso por caso las medidas más oportunas. Si bien los sistemas de simulación computarizada pueden suponer un importante apoyo para la fase de diseño, es responsabilidad del proyectista emplear las herramientas más adecuadas en cada fase y elegir las soluciones más oportunas para cumplir con los objetivos del proyecto. The urban microclimate plays an important role on buildings energy consumption and comfort sensation in exterior spaces. Nowadays, cities need to increase energy efficiency, reduce the pollutants emissions and mitigate the evident lack of sustainability. In reason of this, attention has focused on the bioclimatic urbanism as a reference of change proposal of the way to design and live the city. Hitherto, the researches on microclimate and energy efficiency have mainly concentrated on guiding the design of new constructions. However the main problems of unsustainability of existing conurbations are the result of the growth model highly speculative and responsible of resources depletion that have characterized the real estate boom of recent decades. In Spain and other European countries, become define the need to redirect the construction sector towards urban refurbishment. This alternative is a more sustainable development model and is able to provide a solution for the real estate sector. In order to improve the quality of today's cities, the public space plays a key role, especially in order to provide to citizens places for meeting and socializing. The thermal sensation affects the environment perception, so microclimate conditions can be decisive for the success or failure of urban space. For this reasons, the main objective of this work is focused on the definition of bioclimatic strategies for existing urban spaces, based on the morpho-typological components, climate and comfort requirements for citizens. As novelty element, the regeneration of neighborhoods built in middle of the twentieth century has been studied, because are the major extended in periphery of modern cities and, in many cases, they represent deprived areas. The research methodology is based on the evaluation of climatic conditions and thermal comfort of different project scenarios, applied to three case studies located in a suburban neighborhood of Madrid. The climatic parameters have been obtained by computer simulation process, based on fluid dynamics, thermodynamics and radioactive exchange in urban environment using numerical approach. The great advantage in the use of computing systems is the capacity for evaluate different project scenarios. The results in the different scenarios were compared with the comfort value obtained in the current state, using the UTCI index as indicator of thermal sensation. Finally, an abacus of the thermal comfort improvement obtained by different countermeasures has been performed. One of the major achievement of doctoral work is the demonstration of there are not any design solution suitable for different cases. Each situation should be analyzed and specific design measures should be proposed. Computer simulation systems can be a significant support and help the designer in the decision making phase. However, the election of the most suitable tools and the appropriate solutions for each case is designer responsibility.

Impacto y protección radiológica asociados al transporte de residuos de alta actividad (RAA) al almacén temporal centralizado (ATC) en España

Las cuestiones relacionadas con el transporte de residuos radiactivos de alta actividad (RAA) al previsto almacén temporal centralizado (ATC) en Villar de Cañas (Cuenca) están de actualidad, debido a la movilidad que se espera en un futuro próximo, el compromiso con el medio ambiente, la protección de las personas, así, como la normativa legal reguladora. En esta tesis se ha evaluado el impacto radiológico asociado a este tipo de transportes mediante una nueva herramienta de procesamiento de datos, que puede ser de utilidad y servir como documentación complementaria a la recogida en el marco legal del transporte. Además puede facilitar el análisis desde una perspectiva más científica, para investigadores, responsables públicos y técnicos en general, que pueden utilizar dicha herramienta para simular distintos escenarios de transportes radiactivos basados únicamente en datos de los materiales de entrada y las rutas elegidas. Así, conociendo el nivel de radiación a un metro del transporte y eligiendo una ruta, obtendremos los impactos asociados, tales como las poblaciones afectadas, la dosis recibida por la persona más expuesta, el impacto radiológico global, las dosis a la población en el trayecto y el posible detrimento de su salud. En España se prevé una larga “ruta radiactiva” de más de 2.000 kilómetros, por la que el combustible nuclear gastado se transportará presumiblemente por carretera desde las centrales nucleares hasta el ATC, así como los residuos vitrificados procedentes del reprocesado del combustible de la central nuclear Vandellos I, que en la actualidad están en Francia. Como conclusión más importante, se observa que la emisión de radiaciones ionizantes procedentes del transporte de residuos radiactivos de alta actividad en España, en operación normal, no es significativa a la hora de generar efectos adversos en la salud humana y su impacto radiológico puede considerarse despreciable. En caso de accidente, aunque la posibilidad del suceso es remota, las emisiones, no serán determinantes a la hora de generar efectos adversos en la salud humana. Issues related to the transport of high level radioactive wastes (HLW) to the new centralised temporary storage facility to be built in Villar de Cañas (Cuenca) are attracting renewed attention due to the mobility expected in the near future for these materials, the commitment to the environment, the protection of persons and the legal regulatory standards. This study assesses the radiological impacts associated with this type of transport by means of a new dataprocessing tool, which may be of use and serve as documentation complementary to that included in the legal framework covering transport. Furthermore, it may facilitate analysis from a more scientific perspective for researchers, public servants and technicians in general, who may use the tool to simulate different radioactive transport scenarios based only on input materials data and the routes selected. Thus, by knowing the radiation level at a distance of one metre from the transport and selecting a route, it is possible to obtain the associated impacts, such as the affected populations, the dose received by the most exposed individual, the overall radiological impact and the doses to the public en route and the possible detriment to their health. In Spain a long “radioactive route” of more than 2,000 kilometres is expected, along which spent nuclear fuels will be transported – foreseeably by road – from the nuclear power plants to the CTS facility. The route will also be used for the vitrified wastes from fuel reprocessing of the fuel from Vandellós I nuclear power plant, which are currently in France. In conclusion, it may be observed that the emission of ionising radiations from transport of high level radioactive wastes in Spain is insignificant, in normal operations, as regards the generation of adverse effects for human health, and that the radiological impact may be considered negligible. In the event of an accident, the possibility of which is remote, the emissions will not be also a very determining factor as regards adverse effects for human health.

Manufacturing of self-passivating tungsten based alloys by different powder metallurgical routes

Self-passivating tungsten based alloys will provide a major safety advantage compared to pure tungsten when used as first wall armor of future fusion reactors, due to the formation of a protective oxide layer which prevents the formation of volatile and radioactive WO3 in case of a loss of coolant accident with simultaneous air ingress. Bulk WCr10Ti2 alloys were manufactured by two different powder metallurgical routes: (1) mechanical alloying (MA) followed by hot isostatic pressing (HIP) of metallic capsules, and (2) MA, compaction, pressureless sintering in H2 and subsequent HIPing without encapsulation. Both routes resulted in fully dense materials with homogeneous microstructure and grain sizes of 300 nm and 1 μm, respectively. The content of impurities remained unchanged after HIP, but it increased after sintering due to binder residue. It was not possible to produce large samples by route (2) due to difficulties in the uniaxial compaction stage. Flexural strength and fracture toughness measured on samples produced by route (1) revealed a ductile-to-brittle-transition temperature (DBTT) of about 950 °C. The strength increased from room temperature to 800 °C, decreasing significantly in the plastic region. An increase of fracture toughness is observed around the DBTT.

Modelling and Control of Stepper Motors for High Accuracy Positioning Systems Used in Radioactive Environments

Hybrid Stepper Motors are widely used in open-loop position applications. They are the choice of actuation for the collimators in the Large Hadron Collider, the largest particle accelerator at CERN. In this case the positioning requirements and the highly radioactive operating environment are unique. The latter forces both the use of long cables to connect the motors to the drives which act as transmission lines and also prevents the use of standard position sensors. However, reliable and precise operation of the collimators is critical for the machine, requiring the prevention of step loss in the motors and maintenance to be foreseen in case of mechanical degradation. In order to make the above possible, an approach is proposed for the application of an Extended Kalman Filter to a sensorless stepper motor drive, when the motor is separated from its drive by long cables. When the long cables and high frequency pulse width modulated control voltage signals are used together, the electrical signals difer greatly between the motor and drive-side of the cable. Since in the considered case only drive-side data is available, it is therefore necessary to estimate the motor-side signals. Modelling the entire cable and motor system in an Extended Kalman Filter is too computationally intensive for standard embedded real-time platforms. It is, in consequence, proposed to divide the problem into an Extended Kalman Filter, based only on the motor model, and separated motor-side signal estimators, the combination of which is less demanding computationally. The efectiveness of this approach is shown in simulation. Then its validity is experimentally demonstrated via implementation in a DSP based drive. A testbench to test its performance when driving an axis of a Large Hadron Collider collimator is presented along with the results achieved. It is shown that the proposed method is capable of achieving position and load torque estimates which allow step loss to be detected and mechanical degradation to be evaluated without the need for physical sensors. These estimation algorithms often require a precise model of the motor, but the standard electrical model used for hybrid stepper motors is limited when currents, which are high enough to produce saturation of the magnetic circuit, are present. New model extensions are proposed in order to have a more precise model of the motor independently of the current level, whilst maintaining a low computational cost. It is shown that a significant improvement in the model It is achieved with these extensions, and their computational performance is compared to study the cost of model improvement versus computation cost. The applicability of the proposed model extensions is demonstrated via their use in an Extended Kalman Filter running in real-time for closed-loop current control and mechanical state estimation. An additional problem arises from the use of stepper motors. The mechanics of the collimators can wear due to the abrupt motion and torque profiles that are applied by them when used in the standard way, i.e. stepping in open-loop. Closed-loop position control, more specifically Field Oriented Control, would allow smoother profiles, more respectful to the mechanics, to be applied but requires position feedback. As mentioned already, the use of sensors in radioactive environments is very limited for reliability reasons. Sensorless control is a known option but when the speed is very low or zero, as is the case most of the time for the motors used in the LHC collimator, the loss of observability prevents its use. In order to allow the use of position sensors without reducing the long term reliability of the whole system, the possibility to switch from closed to open loop is proposed and validated, allowing the use of closed-loop control when the position sensors function correctly and open-loop when there is a sensor failure. A different approach to deal with the switched drive working with long cables is also presented. Switched mode stepper motor drives tend to have poor performance or even fail completely when the motor is fed through a long cable due to the high oscillations in the drive-side current. The design of a stepper motor output fillter which solves this problem is thus proposed. A two stage filter, one devoted to dealing with the diferential mode and the other with the common mode, is designed and validated experimentally. With this ?lter the drive performance is greatly improved, achieving a positioning repeatability even better than with the drive working without a long cable, the radiated emissions are reduced and the overvoltages at the motor terminals are eliminated.

Proprioceptive force estimation and control for teleoperation in radioactive environments

A medida que se incrementa la energía de los aceleradores de partículas o iones pesados como el CERN o GSI, de los reactores de fusión como JET o ITER, u otros experimentos científicos, se va haciendo cada vez más imprescindible el uso de técnicas de manipulación remota para la interacción con el entorno sujeto a la radiación. Hasta ahora la tasa de dosis radioactiva en el CERN podía tomar valores cercanos a algunos mSv para tiempos de enfriamiento de horas, que permitían la intervención humana para tareas de mantenimiento. Durante los primeros ensayos con plasma en JET, se alcanzaban valores cercanos a los 200 μSv después de un tiempo de enfriamiento de 4 meses y ya se hacía extensivo el uso de técnicas de manipulación remota. Hay una clara tendencia al incremento de los niveles de radioactividad en el futuro en este tipo de instalaciones. Un claro ejemplo es ITER, donde se esperan valores de 450 Sv/h en el centro del toroide a los 11 días de enfriamiento o los nuevos niveles energéticos del CERN que harán necesario una apuesta por niveles de mantenimiento remotos. En estas circunstancias se enmarca esta tesis, que estudia un sistema de control bilateral basado en fuerza-posición, tratando de evitar el uso de sensores de fuerza/par, cuyo contenido electrónico los hace especialmente sensitivos en estos ambientes. El contenido de este trabajo se centra en la teleoperación de robots industriales, que debido a su reconocida solvencia y facilidad para ser adaptados a estos entornos, unido al bajo coste y alta disponibilidad, les convierte en una alternativa interesante para tareas de manipulación remota frente a costosas soluciones a medida. En primer lugar se considera el problema cinemático de teleoperación maestro-esclavo de cinemática disimilar y se desarrolla un método general para la solución del problema en el que se incluye el uso de fuerzas asistivas para guiar al operador. A continuación se explican con detalle los experimentos realizados con un robot ABB y que muestran las dificultades encontradas y recomendaciones para solventarlas. Se concluye el estudio cinemático con un método para el encaje de espacios de trabajo entre maestro y esclavo disimilares. Posteriormente se mira hacia la dinámica, estudiándose el modelado de robots con vistas a obtener un método que permita estimar las fuerzas externas que actúan sobre los mismos. Durante la caracterización del modelo dinámico, se realizan varios ensayos para tratar de encontrar un compromiso entre complejidad de cálculo y error de estimación. También se dan las claves para modelar y caracterizar robots con estructura en forma de paralelogramo y se presenta la arquitectura de control deseada. Una vez obtenido el modelo completo del esclavo, se investigan diferentes alternativas que permitan una estimación de fuerzas externas en tiempo real, minimizando las derivadas de la posición para minimizar el ruido. Se comienza utilizando observadores clásicos del estado para ir evolucionando hasta llegar al desarrollo de un observador de tipo Luenberger-Sliding cuya implementación es relativamente sencilla y sus resultados contundentes. También se analiza el uso del observador propuesto durante un control bilateral simulado en el que se compara la realimentación de fuerzas obtenida con las técnicas clásicas basadas en error de posición frente a un control basado en fuerza-posición donde la fuerza es estimada y no medida. Se comprueba como la solución propuesta da resultados comparables con las arquitecturas clásicas y sin embargo introduce una alternativa para la teleoperación de robots industriales cuya teleoperación en entornos radioactivos sería imposible de otra manera. Finalmente se analizan los problemas derivados de la aplicación práctica de la teleoperación en los escenarios mencionados anteriormente. Debido a las condiciones prohibitivas para todo equipo electrónico, los sistemas de control se deben colocar a gran distancia de los manipuladores, dando lugar a longitudes de cable de centenares de metros. En estas condiciones se crean sobretensiones en controladores basados en PWM que pueden ser destructivas para el sistema formado por control, cableado y actuador, y por tanto, han de ser eliminadas. En este trabajo se propone una solución basada en un filtro LC comercial y se prueba de forma extensiva que su inclusión no produce efectos negativos sobre el control del actuador. ABSTRACT As the energy on the particle accelerators or heavy ion accelerators such as CERN or GSI, fusion reactors such as JET or ITER, or other scientific experiments is increased, it is becoming increasingly necessary to use remote handling techniques to interact with the remote and radioactive environment. So far, the dose rate at CERN could present values near several mSv for cooling times on the range of hours, which allowed human intervention for maintenance tasks. At JET, they measured values close to 200 μSv after a cooling time of 4 months and since then, the remote handling techniques became usual. There is a clear tendency to increase the radiation levels in the future. A clear example is ITER, where values of 450 Sv/h are expected in the centre of the torus after 11 days of cooling. Also, the new energetic levels of CERN are expected to lead to a more advanced remote handling means. In these circumstances this thesis is framed, studying a bilateral control system based on force-position, trying to avoid the use of force/torque sensors, whose electronic content makes them very sensitive in these environments. The contents of this work are focused on teleoperating industrial robots, which due its well-known reliability, easiness to be adapted to these environments, cost-effectiveness and high availability, are considered as an interesting alternative to expensive custom-made solutions for remote handling tasks. Firstly, the kinematic problem of teloperating master and slave with dissimilar kinematics is analysed and a new general approach for solving this issue is presented. The solution includes using assistive forces in order to guide the human operator. Coming up next, I explain with detail the experiments accomplished with an ABB robot that show the difficulties encountered and the proposed solutions. This section is concluded with a method to match the master’s and slave’s workspaces when they present dissimilar kinematics. Later on, the research studies the dynamics, with special focus on robot modelling with the purpose of obtaining a method that allows to estimate external forces acting on them. During the characterisation of the model’s parameters, a set of tests are performed in order to get to a compromise between computational complexity and estimation error. Key points for modelling and characterising robots with a parallelogram structure are also given, and the desired control architecture is presented. Once a complete model of the slave is obtained, different alternatives for external force estimation are review to be able to predict forces in real time, minimizing the position differentiation to minimize the estimation noise. The research starts by implementing classic state observers and then it evolves towards the use of Luenberger- Sliding observers whose implementation is relatively easy and the results are convincing. I also analyse the use of proposed observer during a simulated bilateral control on which the force feedback obtained with the classic techniques based on the position error is compared versus a control architecture based on force-position, where the force is estimated instead of measured. I t is checked how the proposed solution gives results comparable with the classical techniques and however introduces an alternative method for teleoperating industrial robots whose teleoperation in radioactive environments would have been impossible in a different way. Finally, the problems originated by the practical application of teleoperation in the before mentioned scenarios are analysed. Due the prohibitive conditions for every electronic equipment, the control systems should be placed far from the manipulators. This provokes that the power cables that fed the slaves devices can present lengths of hundreds of meters. In these circumstances, overvoltage waves are developed when implementing drives based on PWM technique. The occurrence of overvoltage is very dangerous for the system composed by drive, wiring and actuator, and has to be eliminated. During this work, a solution based on commercial LC filters is proposed and it is extensively proved that its inclusion does not introduce adverse effects into the actuator’s control.