Assessment of expected damage on buildings subjected to Lorca earthquake through an energy-based seismic index method and nonlinear dynamic response analyses

The city of Lorca (Spain) was hit on May 11th, 2011, by two consecutive earth-quakes of magnitudes 4.6 and 5.2 Mw, causing casualties and important damage in buildings. Many of the damaged structures were reinforced concrete frames with wide beams. This study quantifies the expected level of damage on this structural type in the case of the Lorca earth-quake by means of a seismic index Iv that compares the energy input by the earthquake with the energy absorption/dissipation capacity of the structure. The prototype frames investigated represent structures designed in two time periods (1994–2002 and 2003–2008), in which the applicable codes were different. The influence of the masonry infill walls and the proneness of the frames to concentrate damage in a given story were further investigated through nonlinear dynamic response analyses. It is found that (1) the seismic index method predicts levels of damage that range from moderate/severe to complete collapse; this prediction is consistent with the observed damage; (2) the presence of masonry infill walls makes the structure very prone to damage concentration and reduces the overall seismic capacity of the building; and (3) a proper hierarchy of strength between beams and columns that guarantees the formation of a strong column-weak beam mechanism (as prescribed by seismic codes), as well as the adoption of counter-measures to avoid the negative interaction between non-structural infill walls and the main frame, would have reduced the level of damage from Iv=1 (collapse) to about Iv=0.5 (moderate/severe damage)

Quality grading of cork stoppers based on porosity, density and elasticity.

An objective control method for grading cork stoppers is presented using a cork stopper quality index based on porosity, density and elasticity, these being the properties which have the greatest influence on the closure capacity of the stopper. The elasticity of the cork stopper is measured through the relaxation ratio, which is defined by the relationship between the relaxation force exerted by the cork in the bottleneck and the compressive force exerted by a caliper to fit the stopper in the bottle. The relaxation ratio, defined in this way, represents the part of the compression force which is applied to the stopper on insertion and which is recovered in the form of the relaxation force to achieve closure. The calculation of the relaxation ratio involves the measurement of the relaxation force of the fitted stopper. This force has been measured rigorously and precisely using a device developed in the Cork Laboratory at the INIA-CIFOR and which is presented for the first time in this paper.

Application of Decision Theory methods for a Community of Madrid Soil classification case

A land classification method was designed for the Community of Madrid (CM), which has lands suitable for either agriculture use or natural spaces. The process started from an extensive previous CM study that contains sets of land attributes with data for 122 types and a minimum-requirements method providing a land quality classification (SQ) for each land. Borrowing some tools from Operations Research (OR) and from Decision Science, that SQ has been complemented by an additive valuation method that involves a more restricted set of 13 representative attributes analysed using Attribute Valuation Functions to obtain a quality index, QI, and by an original composite method that uses a fuzzy set procedure to obtain a combined quality index, CQI, that contains relevant information from both the SQ and the QI methods.

Optimización de los procesos de medida e interpretación de la tomografía geoeléctrica en la prospección superficial

Debido al carácter innovador de los objetivos científico-tecnológicos planteados al inicio de la presente Tesis doctoral, además de la primera recopilación bibliográfica, a lo largo del desarrollo de la misma se ha realizado una actualización bibliográfica continua centrada en los desarrollos relativos a la instrumentación, las aplicaciones y los procesos de interpretación de las técnicas de tomografía eléctrica. Durante el desarrollo del presente trabajo, se han realizado una serie de campañas diferenciadas, tanto por los ambientes geológicos y las condiciones antrópicas en los que se han efectuado los perfiles geoeléctricos, como por la profundidad y los objetivos de la prospección. En esas campañas se han obtenido, mediante el programa Res2DInv, las secciones tomográficas con la configuración de variables por defecto y se ha realizado una interpretación estructural de las mismas. Como parte central del desarrollo de esta investigación se han efectuado varios procesos de optimización: Comparación y optimización de los dispositivos empleados para la medición de perfiles de resistividad de cara a la obtención de secciones tomográficas que presenten la mayor resolución en distintos ambientes geológicos. Selección de los rangos de representación (lineales y logarítmicos) y de la gradación cromática que, pudiendo adoptarse de forma generalizada, permita la mejor interpretación gráfica para usuarios no avanzados. Diseño de criterios para la selección del factor de amortiguamiento, como parámetro crítico en los procesos de inversión tomográfica de perfiles geoeléctricos de superficie, de forma que los modelos resultantes alcancen la mejor relación entre fiabilidad y error respecto a los valores medidos. Paralelamente a los procesos anteriores se ha definido un índice de calidad de la inversión, que es directamente normalizado y que permite evaluar el grado en el que pueden considerarse fiables tanto los valores de resistividad obtenidos como su distribución espacial. El índice desarrollado (IRI) está basado en la influencia que tiene la resistividad inicial del modelo de inversión en los valores de cada una de las celdas de la malla de inversión. Tras un exhaustivo análisis estadístico se ha verificado que, a diferencia de otros índices utilizados hasta la fecha, dicho índice no está afectado ni por la profundidad de investigación y la resolución de los dispositivos, ni por la distribución de resistividades que presente el subsuelo. ABSTRACT Due to the innovative character of the scientific and technological objectives proposed at the beginning of this thesis, in addition to preparatory bibliographic reference, a constant bibliographic update on developments related to instrumentation, applications and interpretation processes for electric tomography has been performed all through the development of the work. Several measuring campaigns were performed during the development of the thesis. These campaigns, in which the geoelectric profiles were measured, varied in several aspects, both in the geological and anthropic conditions, and also in the depth and objectives of the prospection. Tomographic sections were obtained and interpretated by making use of the Res2DInv software configured with the default variables. As part of the core development in this research, several optimization processes have been done: Comparison and optimization of the devices used in the measurement of resistivity profiles. This optimization allows increasing the resolution of tomographic sections in different geological conditions. Selection of the best visual representation for the tomographic sections. This involves the selection of the range of values and type of scale (linear vs. logarithmic) as well as the chromatic graduation. This selection allows improving the interpretation of tomographic sections for the non-expert eye. Devising of criteria for the selection of the damping factor, as the critical parameter in processes of tomographic inversion of superficial geoelectrical profiles. The use of these criteria allows selecting the best factors to obtain the best ratio between reliability and error (in relation to the mean values) for the resulting model. In addition to the aforementioned processes, and as part of the work within this thesis, it has been defined a normalized quality index for inversion. This index allows evaluating the degree of reliability of the obtained resistivity values and spatial distribution. The developed index, termed IRI in the thesis, is based on the influence shown by the initial resistivity of the inversion model on the values of each of the cells of the inversion mesh. After an exhaustive statistical analysis it was verified that the IRI index is neither affected by the investigation depth, nor the resolution of the devices, nor the resistivity’s distribution of the sub soil. This independency is a unique characteristic of the IRI index, not present in other indexes developed and used till date.

Use of the First Derivative of Spectral Reflectance to Detect Mold on Tomatoes

The first derivative of spectral reflectance of tomatoes was studied to see whether it can detect molds and sunscald damage on the fruit. The results indicate that a quality index based on the derivative values of reflectance at 590- and 710-nm wavelengths can be used to separate good tomates from those with black mold, gray mold, and sunscald.

Scalable Raid Storage Based on the Structure of Multimedia File.

In professional video production, users have to access to huge multimedia files simultaneously in an error-free environment, this restriction force the use of expensive disk architectures for video servers. Previous researches proposed different RAID systems for each specific task (ingest, editing, file, play-out, etc.). Video production companies have to acquire different servers with different RAIDs systems in order to support each task in the production workflow. The solution has multiples disadvantages, duplicated material in several RAIDs, duplicated material for different qualities, transfer and transcoding processes, etc. In this work, an architecture for video servers based on the spreading of JPEG200 data in different RAIDs is presented, each individual part of the data structure goes to a specific RAID type depending on the effect that produces the data on the overall image quality, the method provide a redundancy correlated with the data rank. The global storage can be used in all the different tasks of the production workflow saving disk space, redundant files and transfers procedures.

Sistemas de Gestión de la Calidad. Metodología para implementar proyectos de mejora continua para la reducción de los defectos de construcción en edificación de viviendas

La mejora continua debería estar presente siempre en las empresas, dispongan o no de sistemas de gestión. Sin embargo, su aplicación en el sector de la construcción es especialmente difícil debido a las características particulares del mismo. Por este motivo se plantea el objetivo principal de esta Tesis Doctoral: “Establecer una metodología de trabajo que permita a las empresas constructoras implantar proyectos de mejora continua para incrementar la calidad de las viviendas entregadas a los usuarios”. En la investigación llevada a cabo se han inspeccionado 818 viviendas, recogiendo un total de 82.550 incidencias, las cuales se han analizado aplicando cuatro de las siete herramientas estadísticas básicas de la mejora continua (Hoja de recogida de datos, Estratificación, Histograma y Diagrama de Pareto), concluyendo que los tres oficios que concentran el 80% de los defectos, en los que convendría actuar para reducir de manera significativa los fallos de construcción en la fase de pre-entrega, son: Carpintería de Madera, Revestimientos Cerámicos e Instalación de Electricidad. De entre estos tres oficios se ha seleccionado el de Revestimientos Cerámicos para poner en práctica un proyecto de mejora continua. Analizando los datos relativos a este oficio se elabora un listado de 25 defectos tipo en los que se pueden agrupar todas las incidencias detectadas. Aplicando de nuevo las cuatro herramientas básicas de la calidad se destacan los 10 defectos tipo con mayor impacto en volumen de incidencias y en coste de reparación, para focalizar los esfuerzos de mejora. Con esta información se elabora un documento de criterios técnicos para la ejecución de los Revestimientos Cerámicos que se implanta, en parte, en varias obras para tratar de reducir los defectos detectados en las viviendas antes de la entrega a sus propietarios, y se definen unos Índices de Calidad para medir los resultados. Se toman datos de nuevo a 6 y 20 meses desde la implantación del protocolo, se analizan y se calculan los resultados del proyecto de mejora, concluyendo que se está avanzando positivamente. En base a toda la información recogida a lo largo del proceso de la investigación y de la experiencia del proyecto de mejora implantado, se presenta una propuesta de metodología para implementar proyectos de mejora, así como la documentación recomendada para su puesta en práctica, además de la documentación técnica específica para la prevención de los defectos de construcción en Revestimientos Cerámicos incluyendo las fichas de control para la recepción de materiales, control de ejecución y control de recepción del revestimiento terminado. ABSTRACT Continuous improvement should always be a core value in firms of all kinds, whether or not they implement management systems. Nevertheless, its application in the construction sector seems especially difficult due to its inherent intricacies and complexity. The study of this phenomenon is the main aim of the hereby presented PhD dissertation "Establishment of a working methodology that allows construction (related) firms to carry out projects of continuous improvement in order to increase the quality of housing upon delivery to the client". In the present research 818 housing units have been inspected, collecting a total of 82550 incidence entries, which have been analyzed by means of 4 out of the 7 basic statistical tools of continuous improvement: Data collection sheets, stratification, histogram, and Pareto diagram. The data shows that the 3 main trades where special actions should be taken in order to significantly reduce construction defects are: carpentry, ceramic cladding, and electricity systems. These trades combined account for the 80% of the total defects detected during the inspections. Among the mentioned works, ceramic tiling is selected as a continuous improvement case study project. Analysing data relative to this specific trade, a list of 25 defect types is developed. These types gather all detected defects under this group. Further applying the four statistical tools referred to above, the 10 most significant events are highlighted as to clearly determine the improvement measures. These events have the most impact on both volume of defects and reparation costs. This information is then put together in a document of technical criteria for the correct execution of ceramic tiling that is implemented in various ongoing projects under construction as to minimize the defects prior to the final delivery to the client. Also, a series of Quality Index are defined as criteria for execution suitability. 6 to 20 months after the implementation of this control protocol, the same process is repeated with the purpose of comparing results. It is concluded that a positive evolution takes place. Based both on the information collected throughout the research process and the experience of the case study, the dissertation proposes a methodology to successfully implement improvement projects along with reference documentation and specific technical documents for the prevention of construction defects in ceramic tiling, including (i) material reception control sheets, (ii) an execution control sheet, and a sheet relative to the (iii) control of the finished cladding.

Decision-Making Mechanism to Organize the Agenda of a Guide-Robot

One of the major challenges in evolutionary robotics is constituted by the need of the robot being able to make decisions on its own, in accordance with the multiple tasks programmed, optimizing its timings and power. In this paper, we present a new automatic decision making mechanism for a robot guide that allows the robot to make the best choice in order to reach its aims, performing its tasks in an optimal way. The election of which is the best alternative is based on a series of criteria and restrictions of the tasks to perform. The software developed in the project has been verified on the tour-guide robot Urbano. The most important aspect of this proposal is that the design uses learning as the means to optimize the quality in the decision making. The modeling of the quality index of the best choice to perform is made using fuzzy logic and it represents the beliefs of the robot, which continue to evolve in order to match the "external reality”. This fuzzy system is used to select the most appropriate set of tasks to perform during the day. With this tool, the tour guide-robot prepares its agenda daily, which satisfies the objectives and restrictions, and it identifies the best task to perform at each moment. This work is part of the ARABOT project of the Intelligent Control Research Group at the Universidad Politécnica de Madrid to create "awareness" in a robot guide.

Cartografía de QTL asociados a la tolerancia a estrés hídrico en frijol común (Phaseolus vulgaris L.)

Phaseolus vulgaris L. (frijol común o judía) es una leguminosa de gran demanda para la nutrición humana y un producto agrícola muy importante. Sin embargo, la producción de frijol se ve limitada por presiones ambientales como la sequía. En México, el 85% de la cosecha de frijol se produce en la temporada de primavera-verano, principalmente en las regiones del altiplano semiárido con una precipitación anual entre 250 y 400 mm. A pesar del implemento de tecnología en el campo, los factores naturales impiden al agricultor llegar a los rendimientos deseados. El Instituto Nacional de Investigaciones Forestales, Agrícolas y Pecuarias (INIFAP), como instituto de investigación gubernamental en México, tiene como objetivo la mejora de cultivos estratégicos, uno de ellos, P. vulgaris. Los estudios en relación a la sequía se enfocan especialmente en la selección de genotipos tolerantes, los cuales son sometidos en condiciones de estrés y monitoreando parámetros como el rendimiento y peso de semilla, además de algunos indicadores tales como índice de cosecha. El resultado de estos trabajos ha sido la obtención de variedades con mayor tolerancia a la sequía, tales como Pinto Villa y Pinto Saltillo. En los últimos años se ha avanzado notablemente en el conocimiento de las bases moleculares en las respuestas de las plantas al estrés. De acuerdo a diversos estudios se ha demostrado que las plantas bajo estrés por sequía experimentan cambios en la expresión de genes involucrados en la señalización, regulación de la transcripción y la traducción, transporte de agua y la función directa en la protección celular. También se ha observado que el déficit de agua es causado por las temperaturas extremas y la alta concentración de sales, por lo que al nivel molecular, las respuestas al estrés tienen puntos de especificidad y puntos de entrecruzamiento. La sequía puede generar estreses secundarios, tales como el nutricional, oxidativo y osmótico. Sin embargo, es necesario identificar y caracterizar muchos de los componentes involucrados en las respuestas al déficit hídrico, la caracterización de estos genes permitirá tener una mejor comprensión de los mecanismos bioquímicos y fisiológicos involucrados en la tolerancia al estrés. Actualmente, con el apoyo de la biología molecular se han identificado algunos genes que otorgan ventajas para la adaptación a ambientes desfavorables. Por lo que el objetivo del presente trabajo es identificar marcadores genéticos asociados a rasgos fenotípicos con énfasis a la tolerancia a estrés hídrico en P. vulgaris. Una vez establecidos los marcadores asociados al estrés hídrico, es factible considerar su uso para la selección asistida por marcadores en líneas o variedades de frijol de interés para los mejoradores. Se evaluaron 282 familias F3:5 derivadas de la cruza entre los cultivares Pinto Villa y Pinto Saltillo. Las familias se sembraron bajo un diseño simple de látice 17x17, el experimento se llevo acabo en el ciclo primavera-verano del 2010 y 2011, y otoñoinvierno de 2010 en el Campo Experimental Bajío del INIFAP con dos repeticiones para cada tratamiento de humedad (riego completo y sequía terminal). En todos los genotipos se realizó el fenotipado (variables fenotípicas) y el genotipado a través de marcadores moleculares. Los análisis estadísticos se basaron en el análisis de componentes principales (Eigen Analysis Selection Index Method, ESIM), la asociación entre marcadores SNP y el fenotipado (paquete SNPassoc para R) y el análisis de varianza (ANOVA). Los valores ESIM mostraron que las variables de Rendimiento, Días a floración, Días a madurez fisiológica e Índice de cosecha fueron sobresalientes en sequía terminal, por lo que se sugieren tomarse en consideración para los estudios de sequía en P. vulgaris como monitores de evaluación a la resistencia. Se identificaron nueve familias sobresalieron por sus valores ESIM (PV/PS6, 22, 131, 137, 149, 154, 201, 236 y 273), además de presentar valores superiores para el rendimiento en comparación con los parentales. Estos genotipos son candidatos interesantes para realizar estudios de identificación de loci asociados con la respuesta al estrés, y como potenciales parentales en el desarrollo de nuevas variedades de frijol. En los análisis de asociación SNPassoc se identificaron 83 SNPs significativos (p<0,0003) asociados a los rasgos fenotípicos, obteniendo un total de 222 asociaciones, de las cuales predomina el modelo genético de codominancia para las variables Días a floración, Periodo reproductivo y Biomasa total. Treinta y siete SNPs se identificaron a diferentes funciones biológicas a través del análisis de anotación funcional, de los cuales 12 SNPs (9, 18, 28, 39, 61, 69, 80, 106, 115, 128, 136 y 142) sobresalen por su asociación al fenotipado, y cuya anotación funcional indica que se encuentran en genes relacionados a la tolerancia a la sequía, tales como la actividad kinasa, actividad metabólica del almidón, carbohidratos y prolina, respuesta al estrés oxidativo, así como en los genes LEA y posibles factores de transcripción. En el caso de los análisis ANOVA, se identificaron 72 asociaciones entre los SNPs y las variables fenotípicas (F< 3,94E-04). Las 72 asociaciones corresponden a 30 SNPs y 7 variables fenotípicas, de las que predomina Peso de 100 semillas y Periodo reproductivo. Para los rasgos de Rendimiento, Índice de cosecha y Días a madurez fisiológica se presentaron asociaciones con seis SNPs (17, 34, 37, 50, 93 y 107), de los cuales, a los SNP37 y SNP107 fueron identificados a la anotación biológica de protein binding. Por otro lado, los SNP106 y SNP128 asociados al Periodo reproductivo, son genes con actividad kinasa y actividad metabólica del almidón, respectivamente. Para los marcadores tipo AFLP, se identificaron 271 asociaciones (F<2,34E-04). Las asociaciones corresponden a 86 AFLPs con todas las variables fenotípicas evaluadas, de las que predomina peso de 100 semillas, Días a floración y Periodo reproductivo. Debido a que los en los AFLPs no es posible determinar su anotación biológica, se proponen como marcadores potenciales relacionados a la resistencia a la sequía en frijol. Los AFLPs candidatos requieren más estudios tales como la secuenciación de los alelos respectivos, así como la identificación de éstas secuencias en el genoma de referencia y su anotación biológica, entre otros análisis, de esta manera podríamos establecer aquellos marcadores candidatos a la validación para la selección asistida. El presente trabajo propone tanto genotipos como marcadores genéticos, que deben ser validados para ser utilizados en el programa de mejoramiento de P. vulgaris, con el objetivo de desarrollar nuevas líneas o variedades tolerantes a la sequía. ABSTRACT Phaseolus vulgaris L. (common bean or judia) is a legume of great demand for human consumption and an important agricultural product. However, the common bean production is limited by environmental stresses, such as drought. In Mexico, 85% of the common bean crop is produced in the spring-summer season mainly in semiarid highland regions with a rainfall between 250 and 400 mm per year. In spite of the improvement of crop technology, the natural factors hamper getting an optimal yield. The National Institute for Forestry, Agriculture and Livestock (INIFAP) is a government research institute from Mexico, whose main objective is the genetic breeding of strategic crops, like P. vulgaris L. The drought tolerance studies particularly focus on the selection of bean tolerant genotypes, which are subjected to stress conditions, by means of monitoring parameters such as yield and seed weight, plus some agronomic indicators such as harvest index. The results of these works have led to obtain cultivars with higher drought tolerance such as Pinto Villa and Pinto Saltillo. Significant achievements have been recently made in understanding the molecular basis of stress plant responses. Several studies have shown that plants under drought stress present changes in gene expression related to cell signalling, transcriptional and translational regulation, water transport and cell protection. In addition, it has been observed that the extreme temperatures and high salt concentrations can cause a water deficiency so, at the molecular level, stress responses have specific and crossover points. The drought can cause secondary stresses, such as nutritional, oxidative and osmotic stress. It is required the identification of more components involved in the response to water deficit, the characterization of these genes will allow a better understanding of the biochemical and physiological mechanisms involved in stress tolerance. Currently, with the support of molecular biology techniques, some genes that confer an advantage for the crop adaptation to unfavourable environments have been identified. The objective of this study is to identify genetic markers associated with phenotypic traits with emphasis on water stress tolerance in P. vulgaris. The establishment of molecular markers linked to drought tolerance would make possible their use for marker-assisted selection in bean breeding programs. Two hundred and eighty two F3:5 families derived from a cross between the drought resistant cultivars Pinto Villa and Pinto Saltillo were evaluated. The families were sowed under a 17x17 simple lattice design. The experiment was conducted between spring-summer seasons in 2010 and 2011, and autumn-winter seasons in 2010 at the Bajio Experimental Station of INIFAP with two treatments (full irrigation and terminal drought). All families were phenotyped and genotyped using molecular markers. Statistical analysis was based on principal component analysis (Eigen Analysis Selection Index Method, ESIM), association analysis between SNP markers and phenotype (SNPassoc package R) and analysis of variance (ANOVA). The ESIM values showed that seed yield, days to flowering, days to physiological maturity and harvest index were outstanding traits in terminal drought treatment, so they could be considered as suitable parameters for drought-tolerance evaluation in P. vulgaris. Nine outstanding families for the ESIM values were identified (PV/PS6, 22, 131, 137, 149, 154, 201, 236 and 273), in addition, these families showed higher values for seed yield compared to the parental cultivars. These families are promising candidates for studies focused on the identification of loci associated to the stress response, and as potential parental cultivars for the development of new varieties of common bean. In the SNPassoc analysis, 83 SNPs were found significantly associated (p<0.0003) with phenotypic traits, obtaining a total of 222 associations, most of which involved the traits days to flowering, reproductive period and total biomass under a codominant genetic model. The functional annotation analysis showed 37 SNPs with different biological functions, 12 of them (9, 18, 28, 39, 61, 69, 80, 106, 115, 128, 136 and 142) stand out by their association to phenotype. The functional annotation suggested a connection with genes related to drought tolerance, such as kinase activity, starch, carbohydrates and proline metabolic processes, responses to oxidative stress, as well as LEA genes and putative transcription factors. In the ANOVA analysis, 72 associations between SNPs and phenotypic traits (F<3.94E- 04) were identified. All of these associations corresponded to 30 SNPs markers and seven phenotypic traits. Weight of 100 seeds and reproductive period were the traits with more associations. Seed yield, harvest index and days to physiological maturity were associated to six SNPs (17, 34, 37, 50, 93 and 107), the SNP37 and SNP107 were identified as located in protein binding genes. The SNP106 and SNP128 were associated with the reproductive period and belonged to genes with kinase activity and genes related to starch metabolic process, respectively. In the case of AFLP markers, 271 associations (F<2.34E-04) were identified. The associations involved 86 AFLPs and all phenotypic traits, being the most frequently associated weight of 100 seeds, days to flowering and reproductive period. Even though it is not possible to perform a functional annotation for AFLP markers, they are proposed as potential markers related to drought resistance in common bean. AFLPs candidates require additional studies such as the sequencing of the respective alleles, identification of these sequences in the reference genome and gene annotation, before their use in marker assisted selection. This work, although requires further validation, proposes both genotypes and genetic markers that could be used in breeding programs of P. vulgaris in order to develop new lines or cultivars with enhanced drought-tolerance.

A new method for the identification of old-growth trees in National Forest Inventories: Application to Pinus halepensis Mill. stands in Spain

Old-growth trees play a very important role in the maintenance of biodiversity in forests. However, no clear definition is yet available to help identify them since tree age is usually not recorded in National Forest Inventories. To develop and test a new method to identify old-growth trees using a species-specific threshold for tree diameter in National Forest Inventories. Different nonlinear mixed models for diameter ? age were generated using data from the Spanish Forest Inventory in order to identify the most appropriate one for Aleppo pine in its South-western distribution area. The asymptote of the optimal model indicates the threshold diameter for defining an old-growth tree. Additionally, five site index curves were examined to analyze the influence of site quality on these models.

An interactive method of fuzzy probability elicitation in risk analysis

Expert knowledge is used to assign probabilities to events in many risk analysis models. However, experts sometimes find it hard to provide specific values for these probabilities, preferring to express vague or imprecise terms that are mapped using a previously defined fuzzy number scale. The rigidity of these scales generates bias in the probability elicitation process and does not allow experts to adequately express their probabilistic judgments. We present an interactive method for extracting a fuzzy number from experts that represents their probabilistic judgments for a given event, along with a quality measure of the probabilistic judgments, useful in a final information filtering and analysis sensitivity process.

Improving parameters selection of a seeded region growing method for multiband image segmentation

In the last decade, Object Based Image Analysis (OBIA) has been accepted as an effective method for processing high spatial resolution multiband images. This image analysis method is an approach that starts with the segmentation of the image. Image segmentation in general is a procedure to partition an image into homogenous groups (segments). In practice, visual interpretation is often used to assess the quality of segmentation and the analysis relies on the experience of an analyst. In an effort to address the issue, in this study, we evaluate several seed selection strategies for an automatic image segmentation methodology based on a seeded region growing-merging approach. In order to evaluate the segmentation quality, segments were subjected to spatial autocorrelation analysis using Moran's I index and intra-segment variance analysis. We apply the algorithm to image segmentation using an aerial multiband image.

Optimizing panchromatic image change detection based on change index multiband image analysis

This work proposes an optimization of a semi-supervised Change Detection methodology based on a combination of Change Indices (CI) derived from an image multitemporal data set. For this purpose, SPOT 5 Panchromatic images with 2.5 m spatial resolution have been used, from which three Change Indices have been calculated. Two of them are usually known indices; however the third one has been derived considering the Kullbak-Leibler divergence. Then, these three indices have been combined forming a multiband image that has been used in as input for a Support Vector Machine (SVM) classifier where four different discriminant functions have been tested in order to differentiate between change and no_change categories. The performance of the suggested procedure has been assessed applying different quality measures, reaching in each case highly satisfactory values. These results have demonstrated that the simultaneous combination of basic change indices with others more sophisticated like the Kullback-Leibler distance, and the application of non-parametric discriminant functions like those employees in the SVM method, allows solving efficiently a change detection problem.

Evaluating the quality of riparian forest vegetation: The Riparian Forest Evaluation (RFV) index

Aim of study: This paper presents a novel index, the Riparian Forest Evaluation (RFV) index, for assessing the ecological condition of riparian forests. The status of riparian ecosystems has global importance due to the ecological and social benefits and services they provide. The initiation of the European Water Framework Directive (2000/60/CE) requires the assessment of the hydromorphological quality of natural channels. The Directive describes riparian forests as one of the fundamental components that determine the structure of riverine areas. The RFV index was developed to meet the aim of the Directive and to complement the existing methodologies for the evaluation of riparian forests. Area of study: The RFV index was applied to a wide range of streams and rivers (170 water bodies) inSpain. Materials and methods: The calculation of the RFV index is based on the assessment of both the spatial continuity of the forest (in its three core dimensions: longitudinal, transversal and vertical) and the regeneration capacity of the forest, in a sampling area related to the river hydromorphological pattern. This index enables an evaluation of the quality and degree of alteration of riparian forests. In addition, it helps to determine the scenarios that are necessary to improve the status of riparian forests and to develop processes for restoring their structure and composition. Main results: The results were compared with some previous tools for the assessment of riparian vegetation. The RFV index got the highest average scores in the basins of northernSpain, which suffer lower human influence. The forests in central and southern rivers got worse scores. The bigger differences with other tools were found in complex and partially altered streams and rivers. Research highlights: The study showed the index’s applicability under diverse hydromorphological and ecological conditions and the main advantages of its application. The utilization of the index allows a better understanding of the status of riparian forests, and enhances improvements in the conservation and management of riparian areas.

Quality cost in bus operations based on activity-based costing

The study of service quality and its implication for transport contracts has several approaches in research and practical applications, where the main emphasis is the consideration of quality from the user's point of view, thus obtaining a customer satisfaction index as a measurement of the overall quality with no further implications for service providers. The main aim of this paper is to estimate the real economic impact of improving quality attributes for a bus operator. An application of the activity-based costing methodology is developed for a bus contract in Madrid, using quality data from surveys together with economic and performance information, and focusing on headway as a quality variable. Results show the consistency and practicality of this methodology, overcoming simplifications from traditional procedures. This method is a powerful tool in quality-based contracting as well as for effective investment in transport quality under poverty funding constraints