Fiabilidad de minimodulos de silicio

El objetivo de este Proyecto Final de Carrera es la realización de un ensayo de fiabilidad de componentes electrónicos, más concretamente de Minimódulos de Silicio, con el fin de estudiar su comportamiento a lo largo del tiempo de vida. Debido a la larga duración de los Minimódulos de Silicio , un ensayo de este tipo podría durar años, por lo que es necesario realizar un ensayo acelerado que acorte significativamente el tiempo del experimento, para ello, han de someterse a esfuerzos mayores que en condiciones normales de funcionamiento. A día de hoy, los Minimódulos de silicio, que conocemos como placas solares fotovoltaicas, se usan en infinidad de dispositivos debido a las múltiples ventajas que conllevan. La principal ventaja es poder llevar electricidad a cualquier parte del planeta sin necesidad de tener que hacer unas elevadas inversiones. Esta electricidad proviene de una fuente de energía inagotable y nada contaminante, con lo que ayudamos a mantener el equilibrio del planeta. La mayoría de las veces estas placas solares fotovoltaicas se usan en el exterior, soportando cambios de temperatura y de humedad elevados, de ahí, la importancia de realizar ensayos de fiabilidad, que muestren sus posibles causas de fallo, los efectos que producen estos fallos y los aspectos de diseño, fabricación y mantenimiento que puedan afectarles. Los Minimódulos de silicio utilizados en este proyecto son el modelo MC-SP0.8-NF-GCS de la empresa fabricante Multicomp. Para realizar el Proyecto hubiéramos necesitado una cámara climática que simulara unas condiciones ambientales determinadas, pero debido a la dificultad de iluminar el módulo dentro de la cámara climática hemos desarrollado un nuevo sistema de ensayos acelerados en temperatura. El nuevo sistema de ensayos acelerados consiste en: •Colocar los módulos fotovoltaicos en el laboratorio con un foco de 500W que irradia lo equivalente al sol. •Los tres módulos trabajarán a tres temperaturas diferentes para simular condiciones ambientales distintas, concretamente a 60°C, 72°C y 84°C. •Mediante un sistema automático de medida diseñado en LabVIEW, de manera simultánea tomará medidas de tensión en las tres placas y estudiaremos el grado degradación en cada placa. Se analizaran los resultados obtenido de cada una de las medidas y se realizará un estudio de fiabilidad y del proceso de degradación sufrido por los Minimódulos de silicio. Este PFC se puede dividir en las siguientes fases de trabajo siendo el ensayo la parte más larga en el tiempo: •Búsqueda de bibliografía documentación y normas aplicables. •Familiarización con los equipos y software, estudiando el manejo del software que viene con el Multímetro Keithley 2601 y el programa LabVIEW. •Desarrollo del hardware y sistemas necesarios para la realización del ensayo. •Montaje del ensayo •Realización del ensayo. •Análisis de resultados. ABSTRACT. The objective of this Final Project is conducting a test reliability of electronic components, more specifically Silicon minimodules, in order to study their behavior throughout the life span. Due to the long duration of Silicon minimodules a test like this could take years, so it is necessary to perform an accelerated significantly shorten the time of the experiment, testing for it, should be subjected to greater efforts than in normal operating. Today, the mini-modules, silicon is known as photovoltaic solar panels are used in a multitude of devices due to the many advantages they bring. The main advantage is to bring electricity to anywhere in the world without having to make high investments. This electricity comes from an inexhaustible source of energy and no pollution, thus helping to maintain the balance of the planet. Most of the time these solar photovoltaic panels are used on the outside, enduring changes in temperature and high humidity, hence, the importance of reliability testing, showing the possible causes of failure, the effects produced by these faults and aspects of design, manufacturing and maintenance that may affect them. The silicon mini-modules used in this project are the MC-SP0.8-NF-GCS model Multicomp manufacturing company. To realize the project we would have needed a climatic chamber to simulate specific environmental conditions, but due to the difficulty of illuminating the module in the climate chamber we have developed a new system of accelerated tests in temperature. The new system is accelerated tests: •Place the PV modules in the laboratory with a focus on the equivalent 500W radiating sun. •The three modules work at three different temperatures to simulate different environmental conditions, namely at 60 °C, 72 °C and 84 °C. •Automatic measurement system designed in LabVIEW, simultaneous voltage measurements taken at the three plates and study the degradation degree in each plate. The results obtained from each of the measurements and a feasibility study and degradation suffered by the silicon is performed minimodules were analyzed. This PFC can be divided into the following phases of the test work the longest part being overtime: •Literature search and documentation standards. •Familiarization with equipment and software, studying management software that comes with the Keithley 2601 multimeter and the LabVIEW program. •Development of hardware and systems necessary for the conduct of the trial. •Experiment setup •Carrying out the experiment. •Analysis of results.

Application of user-centered design in the development of an atomated/assisted testing system for self-service devices

Automated Teller Machines (ATMs) are sensitive self-service systems that require important investments in security and testing. ATM certifications are testing processes for machines that integrate software components from different vendors and are performed before their deployment for public use. This project was originated from the need of optimization of the certification process in an ATM manufacturing company. The process identifies compatibility problems between software components through testing. It is composed by a huge number of manual user tasks that makes the process very expensive and error-prone. Moreover, it is not possible to fully automate the process as it requires human intervention for manipulating ATM peripherals. This project presented important challenges for the development team. First, this is a critical process, as all the ATM operations rely on the software under test. Second, the context of use of ATMs applications is vastly different from ordinary software. Third, ATMs’ useful lifetime is beyond 15 years and both new and old models need to be supported. Fourth, the know-how for efficient testing depends on each specialist and it is not explicitly documented. Fifth, the huge number of tests and their importance implies the need for user efficiency and accuracy. All these factors led us conclude that besides the technical challenges, the usability of the intended software solution was critical for the project success. This business context is the motivation of this Master Thesis project. Our proposal focused in the development process applied. By combining user-centered design (UCD) with agile development we ensured both the high priority of usability and the early mitigation of software development risks caused by all the technology constraints. We performed 23 development iterations and finally we were able to provide a working solution on time according to users’ expectations. The evaluation of the project was carried out through usability tests, where 4 real users participated in different tests in the real context of use. The results were positive, according to different metrics: error rate, efficiency, effectiveness, and user satisfaction. We discuss the problems found, the benefits and the lessons learned in the process. Finally, we measured the expected project benefits by comparing the effort required by the current and the new process (once the new software tool is adopted). The savings corresponded to 40% less effort (man-hours) per certification. Future work includes additional evaluation of product usability in a real scenario (with customers) and the measuring of benefits in terms of quality improvement.

CSR Policies: Effects on Labour Productivity in Spanish Micro and Small Manufacturing Companies

This paper analyses empirical evidence of efforts to enable Spanish micro and small manufacturing companies to boost their labour productivity rates through the development of the main pillars of their corporate social responsibility (CSR) policies. This study aims to develop new approaches and sensibilities towards work from an ethical, values (virtues) and CSR perspective, showing how internal dimensions of CSR, such those related to relationships with employees and responsibility in processes and product quality, can improve labour performance and labour efficiency, thereby contributing to a better society. The results of a sample of 929 small businesses indicate that the social responsibility policies that most contributed to a short-term increase in labour productivity are those related to internal aspects of the company, in particular its involvement in the quality of processes and products, promotion of innovation and employee care. However, the impact on labour productivity of CSR policies related to external factors, such as relationship with stakeholders and environmental concern, could not be empirically proven in this paper.