Effect of the curing conditions of concrete on the behaviour under freeze-thaw cycles*

The aim of this work is to relate the curing conditions of concrete and the addition of an air-entraining admixture with the damage caused by freeze–thaw cycles. In countries with a continental climate, the curing of concrete in summer is performed under climatic conditions of high temperature and low humidity, and during the winter the concrete suffers conditions of freeze–thaw, often accompanied by the use of de-icing salts. This paper shows the experimental results of the behaviour of concrete specimens cured under climatic summer conditions (high temperature and low humidity) and then subjected to freeze–thaw cycles. Curing of the specimens includes conditions of good and bad practice in relation to wetting and protection of the concrete. It also examines the effectiveness of using an air-entraining admixture in both cases. The experimental programme includes an evaluation of the mechanical properties of the concrete, the study of the cement hydration and the measurement of the volume and pore sizes of the concrete. These tests were performed before and after the application of the freeze–thaw cycles. The results obtained showed that the specimens without air-entraining admixture show a deterioration of mechanical properties after the freeze–thaw test. However, the inclusion of air bubbles benefits the behaviour of concrete against freeze–thaw cycles so even better mechanical properties after the test were observed. This anomalous behaviour is because the cement hydration process continues over the freeze–thaw tests, closing the pore structure. This aspect has been confirmed with the DTA and TG tests performed

Decoupling of soil nutrient cycles as a function of aridity in global drylands

The biogeochemical cycles of carbon (C), nitrogen (N) and phosphorus (P) are interlinked by primary production, respiration and decomposition in terrestrial ecosystems. It has been suggested that the C, N and P cycles could become uncoupled under rapid climate change because of the different degrees of control exerted on the supply of these elements by biological and geochemical processes. Climatic controls on biogeochemical cycles are particularly relevant in arid, semi-arid and dry sub-humid ecosystems (drylands) because their biological activity is mainly driven by water availability. The increase in aridity predicted for the twenty-first century in many drylands worldwide may therefore threaten the balance between these cycles, differentially affecting the availability of essential nutrients. Here we evaluate how aridity affects the balance between C, N and P in soils collected from 224 dryland sites from all continents except Antarctica. We find a negative effect of aridity on the concentration of soil organic C and total N, but a positive effect on the concentration of inorganic P. Aridity is negatively related to plant cover, which may favour the dominance of physical processes such as rock weathering, a major source of P to ecosystems, over biological processes that provide more C and N, such as litter decomposition. Our findings suggest that any predicted increase in aridity with climate change will probably reduce the concentrations of N and C in global drylands, but increase that of P. These changes would uncouple the C, N and P cycles in drylands and could negatively affect the provision of key services provided by these ecosystems.

The past distribution of pinus nigra arnold in northern iberia. Contribution from its macroremains.

The presence of Pinus nigra in central Spain, where its natural populations are very rare, has led to different interpretations of the current vegetation dynamics. Complementary to the available palynological evidence, macroremains provide local information of high taxonomic resolution that helps to reconstruct the palaeobiogeography of a given species. Here we present new macrofossil data from Tubilla del Lago, a small palaeolake located at the eastern part of the northern Iberian Meseta. We identified 17 wood samples and 71 cones on the basis of their wood anatomy and morphology, respectively. S ome of the fossil samples were radiocarbon dated (~4.230-3210 years cal BP). The results demonstrate the Holocene presence of P. nigra in the study area, where it is currently extinct. This evidence, together with other published palaeobotanical studies, indicates that the forests dominated by P. nigra must have had a larger importance on the landscape prior to the anthropogenic influence on the northern Iberian Meseta.

Performance of a transmutation advanced device for sustainable energy application

Preliminary studies have been performed to design a device for nuclear waste transmutation and hydrogen generation based on a gas-cooled pebble bed accelerator driven system, TADSEA (Transmutation Advanced Device for Sustainable Energy Application). In previous studies we have addressed the viability of an ADS Transmutation device that uses as fuel wastes from the existing LWR power plants, encapsulated in graphite in the form of pebble beds, cooled by helium which enables high temperatures (in the order of 1200 K), to generate hydrogen from water either by high temperature electrolysis or by thermochemical cycles. For designing this device several configurations were studied, including several reflectors thickness, to achieve the desired parameters, the transmutation of nuclear waste and the production of 100 MW of thermal power. In this paper new studies performed on deep burn in-core fuel management strategy for LWR waste are presented. The fuel cycle on TADSEA device has been analyzed based on both: driven and transmutation fuel that had been proposed by the General Atomic design of a gas turbine-modular helium reactor. The transmutation results of the three fuel management strategies, using driven, transmutation and standard LWR spent fuel were compared, and several parameters describing the neutron performance of TADSEA nuclear core as the fuel and moderator temperature reactivity coefficients and transmutation chain, are also presented

An integral model for natural regeneration of Pinus pinea L. in the Northern Plateau (Spain) = Modelo integral de regeneración natural para Pinus pinea L. en la Meseta Norte (España)

Natural regeneration is an ecological key-process that makes plant persistence possible and, consequently, it constitutes an essential element of sustainable forest management. In this respect, natural regeneration in even-aged stands of Pinus pinea L. located in the Spanish Northern Plateau has not always been successfully achieved despite over a century of pine nut-based management. As a result, natural regeneration has recently become a major concern for forest managers when we are living a moment of rationalization of investment in silviculture. The present dissertation is addressed to provide answers to forest managers on this topic through the development of an integral regeneration multistage model for P. pinea stands in the region. From this model, recommendations for natural regeneration-based silviculture can be derived under present and future climate scenarios. Also, the model structure makes it possible to detect the likely bottlenecks affecting the process. The integral model consists of five submodels corresponding to each of the subprocesses linking the stages involved in natural regeneration (seed production, seed dispersal, seed germination, seed predation and seedling survival). The outputs of the submodels represent the transitional probabilities between these stages as a function of climatic and stand variables, which in turn are representative of the ecological factors driving regeneration. At subprocess level, the findings of this dissertation should be interpreted as follows. The scheduling of the shelterwood system currently conducted over low density stands leads to situations of dispersal limitation since the initial stages of the regeneration period. Concerning predation, predator activity appears to be only limited by the occurrence of severe summer droughts and masting events, the summer resulting in a favourable period for seed survival. Out of this time interval, predators were found to almost totally deplete seed crops. Given that P. pinea dissemination occurs in summer (i.e. the safe period against predation), the likelihood of a seed to not be destroyed is conditional to germination occurrence prior to the intensification of predator activity. However, the optimal conditions for germination seldom take place, restraining emergence to few days during the fall. Thus, the window to reach the seedling stage is narrow. In addition, the seedling survival submodel predicts extremely high seedling mortality rates and therefore only some individuals from large cohorts will be able to persist. These facts, along with the strong climate-mediated masting habit exhibited by P. pinea, reveal that viii the overall probability of establishment is low. Given this background, current management –low final stand densities resulting from intense thinning and strict felling schedules– conditions the occurrence of enough favourable events to achieve natural regeneration during the current rotation time. Stochastic simulation and optimisation computed through the integral model confirm this circumstance, suggesting that more flexible and progressive regeneration fellings should be conducted. From an ecological standpoint, these results inform a reproductive strategy leading to uneven-aged stand structures, in full accordance with the medium shade-tolerant behaviour of the species. As a final remark, stochastic simulations performed under a climate-change scenario show that regeneration in the species will not be strongly hampered in the future. This resilient behaviour highlights the fundamental ecological role played by P. pinea in demanding areas where other tree species fail to persist.

Mejora de la eficacia de Penicillium oxalicum como agente de biocontrol en enfermedades de plantas hortícolas

Actualmente, la reducción de materias activas (UE) y la implantación de la nueva Directiva comunitaria 2009/128/ que establece el marco de actuación para conseguir un uso sostenible de los plaguicidas químicos y la preferencia de uso de métodos biológicos, físicos y otros no químicos, obliga a buscar métodos de control menos perjudiciales para el medio ambiente. El control biológico (CB) de enfermedades vegetales empleando agentes de control biológico (ACB) se percibe como una alternativa más segura y con menor impacto ambiental, bien solos o bien como parte de una estrategia de control integrado. El aislado 212 de Penicillium oxalicum (PO212) (ATCC 201888) fue aislado originalmente de la micoflora del suelo en España y ha demostrado ser un eficaz ACB frente a la marchitez vascular del tomate. Una vez identificado y caracterizado el ACB se inició el periodo de desarrollo del mismo poniendo a punto un método de producción en masa de sus conidias. Tras lo cual se inició el proceso de formulación del ACB deshidratando las conidias para su preservación durante un período de tiempo mayor mediante lecho fluido. Finalmente, se han desarrollado algunos formulados que contienen de forma individual diferentes aditivos que han alargado su viabilidad, estabilidad y facilitado su manejo y aplicación. Sin embargo, es necesario seguir trabajando en la mejora de su eficacia de biocontrol. El primer objetivo de esta Tesis se ha centrado en el estudio de la interacción ACB-patógeno-huésped que permita la actuación de P.oxalicum en diferentes patosistemas. Uno de los primeros puntos que se abordan dentro de este objetivo es el desarrollo de nuevas FORMULACIONES del ACB que incrementen su eficacia frente a la marchitez vascular del tomate. Las conidias formuladas de PO212 se obtuvieron por la adición conjunta de distintos aditivos (mojantes, adherentes o estabilizantes) en dos momentos diferentes del proceso de producción/secado: i) antes del proceso de producción (en la bolsa de fermentación) en el momento de la inoculación de las bolsas de fermentación con conidias de PO212 o ii) antes del secado en el momento de la resuspensión de las conidias tras su centrifugación. De las 22 nuevas formulaciones desarrolladas y evaluadas en plantas de tomate en ensayos en invernadero, seis de ellas (FOR22, FOR25, FOR32, FOR35, FOR36 y FOR37) mejoran significativamente (P=0,05) el control de la marchitez vascular del tomate con respecto al obtenido con las conidias secas de P.oxalicum sin aditivos (CSPO) o con el fungicida Bavistin. Los formulados que mejoran la eficacia de las conidias secas sin aditivos son aquellos que contienen como humectantes alginato sódico en fermentación, seguido de aquellos que contienen glicerol como estabilizante en fermentación, y metil celulosa y leche desnatada como adherentes antes del secado. Además, el control de la marchitez vascular del tomate por parte de los formulados de P. oxalicum está relacionado con la fecha de inicio de la enfermedad. Otra forma de continuar mejorando la eficacia de biocontrol es mejorar la materia activa mediante la SELECCIÓN DE NUEVAS CEPAS de P. oxalicum, las cuales podrían tener diferentes niveles de eficacia. De entre las 28 nuevas cepas de P. oxalicum ensayadas en cámara de cultivo, sólo el aislado PO15 muestra el mismo nivel de eficacia que PO212 (62-67% de control) frente a la marchitez vascular del tomate en casos de alta presión de enfermedad. Mientras que, en casos de baja presión de enfermedad todas las cepas de P. oxalicum y sus mezclas demuestran ser eficaces. Finalmente, se estudia ampliar el rango de actuación de este ACB a OTROS HUÉSPEDES Y OTROS PATÓGENOS Y DIFERENTES GRADOS DE VIRULENCIA. En ensayos de eficacia de P. oxalicum frente a aislados de diferente agresividad de Verticillium spp. y Fusarium oxysporum f. sp. lycopersici en plantas de tomate en cámaras de cultivo, se demuestra que la eficacia de PO212 está negativamente correlacionada con el nivel de enfermedad causada por F. oxysporum f. sp. lycopersici pero que no hay ningún efecto diferencial en la reducción de la incidencia ni de la gravedad según la virulencia de los aislados. Sin embargo, en los ensayos realizados con V. dahliae, PO212 causa una mayor reducción de la enfermedad en las plantas inoculadas con aislados de virulencia media. La eficacia de PO212 también era mayor frente a aislados de virulencia media alta de F. oxysporum f. sp. melonis y F. oxysporum f. sp. niveum, en plantas de melón y sandía, respectivamente. En ambos huéspedes se demuestra que la dosis óptima de aplicación del ACB es de 107 conidias de PO212 g-1 de suelo de semillero, aplicada 7 días antes del trasplante. Además, entre 2 y 4 nuevas aplicaciones de PO212 a la raíces de las plantas mediante un riego al terreno de asiento mejoran la eficacia de biocontrol. La eficacia de PO212 no se limita a hongos patógenos vasculares como los citados anteriormente, sino también a otros patógenos como: Phytophthora cactorum, Globodera pallida y G. rostochiensis. PO212 reduce significativamente los síntomas (50%) causados por P. cactorum en plantas de vivero de fresa, tras la aplicación del ACB por inmersión de las raíces antes de su trasplante al suelo de viveros comerciales. Por otra parte, la exposición de los quistes de Globodera pallida y G. rostochiensis (nematodos del quiste de la patata) a las conidias de P. oxalicum, en ensayos in vitro o en microcosmos de suelo, reduce significativamente la capacidad de eclosión de los huevos. Para G. pallida esta reducción es mayor cuando se emplean exudados de raíz de patata del cv. 'Monalisa', que exudados de raíz del cv. 'Desirée'. No hay una reducción significativa en la tasa de eclosión con exudados de raíz de tomate del cv. 'San Pedro'. Para G. rostochiensis la reducción en la tasa de eclosión de los huevos se obtiene con exudados de la raíz de patata del cv. 'Desirée'. El tratamiento con P. oxalicum reduce también significativamente el número de quistes de G. pallida en macetas. Con el fin de optimizar la aplicación práctica de P. oxalicum cepa 212 como tratamiento biológico del suelo, es esencial entender cómo el entorno físico influye en la capacidad de colonización, crecimiento y supervivencia del mismo, así como el posible riesgo que puede suponer su aplicación sobre el resto de los microorganismos del ecosistema. Por ello en este segundo objetivo de esta tesis se estudia la interacción del ACB con el medio ambiente en el cual se aplica. Dentro de este objetivo se evalúa la INFLUENCIA DE LA TEMPERATURA, DISPONIBILIDAD DE AGUA Y PROPIEDADES FÍSICO-QUÍMICAS DE LOS SUELOS (POROSIDAD, TEXTURA, DENSIDAD...) SOBRE LA SUPERVIVENCIA Y EL CRECIMIENTO DE PO212 en condiciones controladas elaborando modelos que permitan predecir el impacto de cada factor ambiental en la supervivencia y crecimiento de P. oxalicum y conocer su capacidad para crecer y sobrevivir en diferentes ambientes. En las muestras de suelo se cuantifica: i) la supervivencia de Penicillium spp. usando el recuento del número de unidades formadoras de colonias en un medio de cultivo semi-selectivo y ii) el crecimiento (biomasa) de PO212 mediante PCR en tiempo real. En los resultados obtenidos se demuestra que P. oxalicum crece y sobrevive mejor en condiciones de sequía independientemente de la temperatura y del tipo de suelo. Si comparamos tipos de suelo P. oxalicum crece y sobrevive en mayor medida en suelos areno-arcillosos con un bajo contenido en materia orgánica, un mayor pH y una menor disponibilidad de fósforo y nitrógeno. La supervivencia y el crecimiento de P. oxalicum se correlaciona de forma negativa con la disponibilidad de agua y de forma positiva con el contenido de materia orgánica. Sólo la supervivencia se correlaciona también positivamente con el pH. Por otro lado se realizan ensayos en suelos de huertos comerciales con diferentes propiedades físico-químicas y diferentes condiciones ambientales para ESTUDIAR EL ESTABLECIMIENTO, SUPERVIVENCIA Y DISPERSIÓN VERTICAL Y MOVILIDAD HORIZONTAL DE PO212. P. oxalicum 212 puede persistir y sobrevivir en esos suelos al menos un año después de su liberación pero a niveles similares a los de otras especies de Penicillium indígenas presentes en los mismos suelos naturales. Además, P. oxalicum 212 muestra una dispersión vertical y movilidad horizontal muy limitada en los diferentes tipos de suelo evaluados. La introducción de P. oxalicum en un ambiente natural no sólo implica su actuación sobre el microorganismo diana, el patógeno, si no también sobre otros microorganismos indígenas. Para EVALUAR EL EFECTO DE LA APLICACIÓN DE P. oxalicum SOBRE LAS POBLACIONES FÚNGICAS INDIGENAS PRESENTES EN EL SUELO de dos huertos comerciales, se analizan mediante electroforesis en gradiente desnaturalizante de poliacrilamida (DGGE) muestras de dichos suelos a dos profundidades (5 y 10 cm) y a cuatro fechas desde la aplicación de P. oxalicum 212 (0, 75, 180 y 365 días). El análisis de la DGGE muestra que las diferencias entre las poblaciones fúngicas se deben significativamente a la fecha de muestreo y son independientes del tratamiento aplicado y de la profundidad a la que se tomen las muestras. Luego, la aplicación del ACB no afecta a la población fúngica de los dos suelos analizados. El análisis de las secuencias de la DGGE confirma los resultados anteriores y permiten identificar la presencia del ACB en los suelos. La presencia de P. oxalicum en el suelo se encuentra especialmente relacionada con factores ambientales como la humedad. Por tanto, podemos concluir que Penicillium oxalicum cepa 212 puede considerarse un óptimo Agente de Control Biológico (ACB), puesto que es ecológicamente competitivo, eficaz para combatir un amplio espectro de enfermedades y no supone un riesgo para el resto de microorganismos fúngicos no diana presentes en el lugar de aplicación. ABSTRACT Currently, reduction of active (EU) and the implementation of the new EU Directive 2009/128 which establishing the framework for action to achieve the sustainable use of chemical pesticides and preference of use of biological, physical and other non-chemical methods, forces to look for control methods less harmful to the environment. Biological control (CB) of plant diseases using biological control agents (BCA) is perceived as a safer alternative and with less environmental impact, either alone or as part of an integrated control strategy. The isolate 212 of Penicillium oxalicum (PO212) (ATCC 201888) was originally isolated from the soil mycoflora in Spain. P. oxalicum is a promising biological control agent for Fusarium wilt and other tomato diseases. Once identified and characterized the BCA, was developed a mass production method of conidia by solid-state fermentation. After determined the process of obtaining a formulated product of the BCA by drying of product by fluid-bed drying, it enables the preservation of the inoculum over a long period of time. Finally, some formulations of dried P. oxalicum conidia have been developed which contain one different additive that have improved their viability, stability and facilitated its handling and application. However, further work is needed to improve biocontrol efficacy. The first objective of this thesis has focused on the study of the interaction BCA- pathogen-host, to allow P.oxalicum to work in different pathosystems. The first point to be addressed in this objective is the development of new FORMULATIONS of BCA which increase their effectiveness against vascular wilt of tomato. PO212 conidial formulations were obtained by the joint addition of various additives (wetting agents, adhesives or stabilizers) at two different points of the production-drying process: i) to substrate in the fermentation bags before the production process, and (ii) to conidial paste obtained after production but before drying. Of the 22 new formulations developed and evaluated in tomato plants in greenhouse tests, six of them (FOR22 , FOR25 , FOR32 , FOR35 , FOR36 and FOR3) improved significantly (P = 0.05) the biocontrol efficacy against tomato wilt with respect to that obtained with dried P.oxalicum conidia without additives (CSPO) or the fungicide Bavistin. The formulations that improve the efficiency of dried conidia without additives are those containing as humectants sodium alginate in the fermentation bags, followed by those containing glycerol as a stabilizer in the fermentation bags, and methylcellulose and skimmed milk as adherents before drying. Moreover, control of vascular wilt of tomatoes by PO212 conidial formulations is related to the date of disease onset. Another way to further improve the effectiveness of biocontrol is to improve the active substance by SELECTION OF NEW STRAINS of P. oxalicum, which may have different levels of effectiveness. Of the 28 new strains of P. oxalicum tested in a culture chamber, only PO15 isolate shows the same effectiveness that PO212 (62-67 % of control) against tomato vascular wilt in cases of high disease pressure. Whereas in cases of low disease pressure all strains of P. oxalicum and its mixtures effective. Finally, we study extend the range of action of this BCA TO OTHER GUESTS AND OTHER PATHOGENS AND DIFFERENT DEGREES OF VIRULENCE. In efficacy trials of P. oxalicum against isolates of different aggressiveness of Verticillium spp. and Fusarium oxysporum f. sp. lycopersici in tomato plants in growth chambers, shows that the efficiency of PO212 is negatively correlated with the level of disease caused by F. oxysporum f. sp. lycopersici. There is not differential effect in reducing the incidence or severity depending on the virulence of isolates. However, PO212 cause a greater reduction of disease in plants inoculated with virulent isolates media of V. dahlia. PO212 efficacy was also higher against isolates of high and average virulence of F. oxysporum f. sp. melonis and F. oxysporum f. sp. niveum in melon and watermelon plants, respectively. In both hosts the optimum dose of the BCA application is 107 conidia PO212 g-1 soil, applied on seedlings 7 days before transplantation into the field. Moreover, the reapplication of PO212 (2-4 times) to the roots by irrigation into the field improve efficiency of biocontrol. The efficacy of PO212 is not limited to vascular pathogens as those mentioned above, but also other pathogens such as Oomycetes (Phytophthora cactorum) and nematodes (Globodera pallida and G. rostochiensis). PO212 significantly reduces symptoms (50 %) caused by P. cactorum in strawberry nursery plants after application of BCA by dipping the roots before transplanting to soil in commercial nurseries. Moreover, the exposure of G. pallida and G. rostochiensis cysts to the conidia of P. oxalicum, in in vitro assays or in soil microcosms significantly reduces hatchability of eggs. The reduction in the rate of G. pallida juveniles hatching was greatest when root diffusates from the `Monalisa´ potato cultivar were used, followed by root diffusates from the `Désirée´ potato cultivar. However, no significant reduction in the rate of G. pallida juveniles hatching was found when root diffusates from the ‘San Pedro” tomato cultivar were used. For G. rostochiensis reduction in the juveniles hatching is obtained from the root diffusates 'Desirée' potato cultivar. Treatment with P. oxalicum also significantly reduces the number of cysts of G. pallida in pots. In order to optimize the practical application of P. oxalicum strain 212 as a biological soil treatment, it is essential to understand how the physical environment influences the BCA colonization, survival and growth, and the possible risk that can cause its application on other microorganisms in the ecosystem of performance. Therefore, the second objective of this thesis is the interaction of the BCA with the environment in which it is applied. Within this objective is evaluated the INFLUENCE OF TEMPERATURE, WATER AVAILABILITY AND PHYSICAL-CHEMICAL PROPERTIES OF SOILS (POROSITY, TEXTURE, DENSITY...) ON SURVIVAL AND GROWTH OF PO212 under controlled conditions to develop models for predicting the environmental impact of each factor on survival and growth of P. oxalicum and to know their ability to grow and survive in different environments. Two parameters are evaluated in the soil samples: i) the survival of Penicillium spp. by counting the number of colony forming units in semi-selective medium and ii) growth (biomass) of PO212 by real-time PCR. P. oxalicum grows and survives better in drought conditions regardless of temperature and soil type. P. oxalicum grows and survives more in sandy loam soils with low organic matter content, higher pH and lower availability of phosphorus and nitrogen. Survival and growth of P. oxalicum negatively correlates with the availability of water and positively with the organic content. Only survival also correlated positively with pH. Moreover, trials are carried out into commercial orchards soils with different physic-chemical properties and different environmental conditions TO STUDY THE ESTABLISHMENT, SURVIVAL, VERTICAL DISPERSION AND HORIZONTAL SPREAD OF PO212. P. oxalicum 212 can persist and survive at very low levels in soil one year after its release. The size of the PO212 population after its release into the tested natural soils is similar to that of indigenous Penicillium spp. Furthermore, the vertical dispersion and horizontal spread of PO212 is limited in different soil types. The introduction of P. oxalicum in a natural environment not only involves their action on the target organism, the pathogen, but also on other indigenous microorganisms. TO ASSESS THE EFFECT OF P. oxalicum APPLICATION ON SOIL INDIGENOUS FUNGAL COMMUNITIES in two commercial orchards, soil samples are analyzed by Denaturing Gradient Gel Electrophoresis polyacrylamide (DGGE). Samples are taken from soil at two depths (5 and 10 cm) and four dates from the application of P. oxalicum 212 (0, 75, 180 and 365 days). DGGE analysis shows that differences are observed between sampling dates and are independent of the treatment of P. oxalicum applied and the depth. BCA application does not affect the fungal population of the two soil analyzed. Sequence analysis of the DGGE bands confirms previous findings and to identify the presence of BCA on soils. The presence of P. oxalicum in soil is especially related to environmental factors such as humidity. Therefore, we conclude that the 212 of strain Penicillium oxalicum can be considered an optimum BCA, since it is environmentally competitive and effective against a broad spectrum of diseases and does not have any negative effect on soil non-target fungi communities.

Localization and Tracking in Energy-Constrained Networks with Dynamic Connectivity

Systems used for target localization, such as goods, individuals, or animals, commonly rely on operational means to meet the final application demands. However, what would happen if some means were powered up randomly by harvesting systems? And what if those devices not randomly powered had their duty cycles restricted? Under what conditions would such an operation be tolerable in localization services? What if the references provided by nodes in a tracking problem were distorted? Moreover, there is an underlying topic common to the previous questions regarding the transfer of conceptual models to reality in field tests: what challenges are faced upon deploying a localization network that integrates energy harvesting modules? The application scenario of the system studied is a traditional herding environment of semi domesticated reindeer (Rangifer tarandus tarandus) in northern Scandinavia. In these conditions, information on approximate locations of reindeer is as important as environmental preservation. Herders also need cost-effective devices capable of operating unattended in, sometimes, extreme weather conditions. The analyses developed are worthy not only for the specific application environment presented, but also because they may serve as an approach to performance of navigation systems in absence of reasonably accurate references like the ones of the Global Positioning System (GPS). A number of energy-harvesting solutions, like thermal and radio-frequency harvesting, do not commonly provide power beyond one milliwatt. When they do, battery buffers may be needed (as it happens with solar energy) which may raise costs and make systems more dependent on environmental temperatures. In general, given our problem, a harvesting system is needed that be capable of providing energy bursts of, at least, some milliwatts. Many works on localization problems assume that devices have certain capabilities to determine unknown locations based on range-based techniques or fingerprinting which cannot be assumed in the approach considered herein. The system presented is akin to range-free techniques, but goes to the extent of considering very low node densities: most range-free techniques are, therefore, not applicable. Animal localization, in particular, uses to be supported by accurate devices such as GPS collars which deplete batteries in, maximum, a few days. Such short-life solutions are not particularly desirable in the framework considered. In tracking, the challenge may times addressed aims at attaining high precision levels from complex reliable hardware and thorough processing techniques. One of the challenges in this Thesis is the use of equipment with just part of its facilities in permanent operation, which may yield high input noise levels in the form of distorted reference points. The solution presented integrates a kinetic harvesting module in some nodes which are expected to be a majority in the network. These modules are capable of providing power bursts of some milliwatts which suffice to meet node energy demands. The usage of harvesting modules in the aforementioned conditions makes the system less dependent on environmental temperatures as no batteries are used in nodes with harvesters--it may be also an advantage in economic terms. There is a second kind of nodes. They are battery powered (without kinetic energy harvesters), and are, therefore, dependent on temperature and battery replacements. In addition, their operation is constrained by duty cycles in order to extend node lifetime and, consequently, their autonomy. There is, in turn, a third type of nodes (hotspots) which can be static or mobile. They are also battery-powered, and are used to retrieve information from the network so that it is presented to users. The system operational chain starts at the kinetic-powered nodes broadcasting their own identifier. If an identifier is received at a battery-powered node, the latter stores it for its records. Later, as the recording node meets a hotspot, its full record of detections is transferred to the hotspot. Every detection registry comprises, at least, a node identifier and the position read from its GPS module by the battery-operated node previously to detection. The characteristics of the system presented make the aforementioned operation own certain particularities which are also studied. First, identifier transmissions are random as they depend on movements at kinetic modules--reindeer movements in our application. Not every movement suffices since it must overcome a certain energy threshold. Second, identifier transmissions may not be heard unless there is a battery-powered node in the surroundings. Third, battery-powered nodes do not poll continuously their GPS module, hence localization errors rise even more. Let's recall at this point that such behavior is tight to the aforementioned power saving policies to extend node lifetime. Last, some time is elapsed between the instant an identifier random transmission is detected and the moment the user is aware of such a detection: it takes some time to find a hotspot. Tracking is posed as a problem of a single kinetically-powered target and a population of battery-operated nodes with higher densities than before in localization. Since the latter provide their approximate positions as reference locations, the study is again focused on assessing the impact of such distorted references on performance. Unlike in localization, distance-estimation capabilities based on signal parameters are assumed in this problem. Three variants of the Kalman filter family are applied in this context: the regular Kalman filter, the alpha-beta filter, and the unscented Kalman filter. The study enclosed hereafter comprises both field tests and simulations. Field tests were used mainly to assess the challenges related to power supply and operation in extreme conditions as well as to model nodes and some aspects of their operation in the application scenario. These models are the basics of the simulations developed later. The overall system performance is analyzed according to three metrics: number of detections per kinetic node, accuracy, and latency. The links between these metrics and the operational conditions are also discussed and characterized statistically. Subsequently, such statistical characterization is used to forecast performance figures given specific operational parameters. In tracking, also studied via simulations, nonlinear relationships are found between accuracy and duty cycles and cluster sizes of battery-operated nodes. The solution presented may be more complex in terms of network structure than existing solutions based on GPS collars. However, its main gain lies on taking advantage of users' error tolerance to reduce costs and become more environmentally friendly by diminishing the potential amount of batteries that can be lost. Whether it is applicable or not depends ultimately on the conditions and requirements imposed by users' needs and operational environments, which is, as it has been explained, one of the topics of this Thesis.

Dynamics in the governance of collective irrigation systems: Evidence from field experiments in Nicaragua.

In this paper, we investigate the real demand for climate protection when the purely individual perspective of existing revealed preference studies is relaxed. This is achieved in two treatments; first, we determine the information subjects receive about the demand revealed by other subjects in a similar decision making situation, second, collective action is implemented whereby all subjects are required to purchase the group?s median quantity at a given price. Participants in the experiment were offered the opportunity to contribute to climate protection by purchasing European Union Allowances. Allowances purchased were withdrawn from the European Emissions Trading Scheme. In our experiment, information about other subjects? behaviour has no treatment effect on the demand for climate protection. Under collective action however, the probability of purchasing allowances is higher compared to the reference treatment situation, an individual contribution mechanism. Furthermore, we observe a strong correlation between subjects? demand and their expectations about other participants? behaviour. When collective action is not available, subjects? e xpectations are consistent with free rider behaviour.

Licensing patterns for Linked Data

Rights expression languages declare the permitted and prohibited actions to be performed on a resource. Along this work, six rights expression languages are compared, abstracting their commonalities and outlining their underlying pattern. Linked Data, which can be object of protection by the intellectual property laws or its access be restricted by an access control system, can be the asset in rights expressions. The requirements for a pattern for licensing Linked Data resources are listed.

Translocation and Functional Analysis of Pseudomonas savastanoi pv. savastanoi NCPPB 3335 Type III Secretion System Effectors Reveals Two Novel Effector Families of the Pseudomonas syringae Complex

Pseudomonas savastanoi pv. savastanoi NCPPB 3335 causes olive knot disease and is a model pathogen for exploring bacterial infection of woody hosts. The type III secretion system (T3SS) effector repertoire of this strain includes 31 effector candidates plus two novel candidates identified in this study which have not been reported to translocate into plant cells. In this work, we demonstrate the delivery of seven NCPPB 3335 effectors into Nicotiana tabacum leaves, including three proteins from two novel families of the P. syringae complex effector super-repertoire (HopBK and HopBL), one of which comprises two proteins (HopBL1 and HopBL2) that harbor a SUMO protease domain. When delivered by P. fluorescens heterologously expressing a P. syringae T3SS, all seven effectors were found to suppress the production of defense-associated reactive oxygen species. Moreover, six of these effectors, including the truncated versions of HopAA1 and HopAZ1 encoded by NCPPB 3335, suppressed callose deposition. The expression of HopAZ1 and HopBL1 by functionally effectorless P. syringae pv. tomato DC3000D28E inhibited the hypersensitive response in tobacco and, additionally, expression of HopBL2 by this strain significantly increased its competitiveness in N. benthamiana. DNA sequences encoding HopBL1 and HopBL2 were uniquely detected in a collection of 31 P. savastanoi pv. savastanoi strains and other P. syringae strains isolated from woody hosts, suggesting a relevant role of these two effectors in bacterial interactions with olive and other woody plants.

MOVPE growth of III-V semiconductors on silicon for third generation solar cells

Esta Tesis trata sobre el desarrollo y crecimiento -mediante tecnología MOVPE (del inglés: MetalOrganic Vapor Phase Epitaxy)- de células solares híbridas de semiconductores III-V sobre substratos de silicio. Esta integración pretende ofrecer una alternativa a las células actuales de III-V, que, si bien ostentan el récord de eficiencia en dispositivos fotovoltaicos, su coste es, a día de hoy, demasiado elevado para ser económicamente competitivo frente a las células convencionales de silicio. De este modo, este proyecto trata de conjugar el potencial de alta eficiencia ya demostrado por los semiconductores III-V en arquitecturas de células fotovoltaicas multiunión con el bajo coste, la disponibilidad y la abundancia del silicio. La integración de semiconductores III-V sobre substratos de silicio puede afrontarse a través de diferentes aproximaciones. En esta Tesis se ha optado por el desarrollo de células solares metamórficas de doble unión de GaAsP/Si. Mediante esta técnica, la transición entre los parámetros de red de ambos materiales se consigue por medio de la formación de defectos cristalográficos (mayoritariamente dislocaciones). La idea es confinar estos defectos durante el crecimiento de sucesivas capas graduales en composición para que la superficie final tenga, por un lado, una buena calidad estructural, y por otro, un parámetro de red adecuado. Numerosos grupos de investigación han dirigido sus esfuerzos en los últimos años en desarrollar una estructura similar a la que aquí proponemos. La mayoría de éstos se han centrado en entender los retos asociados al crecimiento de materiales III-V, con el fin de conseguir un material de alta calidad cristalográfica. Sin embargo, prácticamente ninguno de estos grupos ha prestado especial atención al desarrollo y optimización de la célula inferior de silicio, cuyo papel va a ser de gran relevancia en el funcionamiento de la célula completa. De esta forma, y con el fin de completar el trabajo hecho hasta el momento en el desarrollo de células de III-V sobre silicio, la presente Tesis se centra, fundamentalmente, en el diseño y optimización de la célula inferior de silicio, para extraer su máximo potencial. Este trabajo se ha estructurado en seis capítulos, ordenados de acuerdo al desarrollo natural de la célula inferior. Tras un capítulo de introducción al crecimiento de semiconductores III-V sobre Si, en el que se describen las diferentes alternativas para su integración; nos ocupamos de la parte experimental, comenzando con una extensa descripción y caracterización de los substratos de silicio. De este modo, en el Capítulo 2 se analizan con exhaustividad los diferentes tratamientos (tanto químicos como térmicos) que deben seguir éstos para garantizar una superficie óptima sobre la que crecer epitaxialmente el resto de la estructura. Ya centrados en el diseño de la célula inferior, el Capítulo 3 aborda la formación de la unión p-n. En primer lugar se analiza qué configuración de emisor (en términos de dopaje y espesor) es la más adecuada para sacar el máximo rendimiento de la célula inferior. En este primer estudio se compara entre las diferentes alternativas existentes para la creación del emisor, evaluando las ventajas e inconvenientes que cada aproximación ofrece frente al resto. Tras ello, se presenta un modelo teórico capaz de simular el proceso de difusión de fosforo en silicio en un entorno MOVPE por medio del software Silvaco. Mediante este modelo teórico podemos determinar qué condiciones experimentales son necesarias para conseguir un emisor con el diseño seleccionado. Finalmente, estos modelos serán validados y constatados experimentalmente mediante la caracterización por técnicas analíticas (i.e. ECV o SIMS) de uniones p-n con emisores difundidos. Uno de los principales problemas asociados a la formación del emisor por difusión de fósforo, es la degradación superficial del substrato como consecuencia de su exposición a grandes concentraciones de fosfina (fuente de fósforo). En efecto, la rugosidad del silicio debe ser minuciosamente controlada, puesto que éste servirá de base para el posterior crecimiento epitaxial y por tanto debe presentar una superficie prístina para evitar una degradación morfológica y cristalográfica de las capas superiores. En este sentido, el Capítulo 4 incluye un análisis exhaustivo sobre la degradación morfológica de los substratos de silicio durante la formación del emisor. Además, se proponen diferentes alternativas para la recuperación de la superficie con el fin de conseguir rugosidades sub-nanométricas, que no comprometan la calidad del crecimiento epitaxial. Finalmente, a través de desarrollos teóricos, se establecerá una correlación entre la degradación morfológica (observada experimentalmente) con el perfil de difusión del fósforo en el silicio y por tanto, con las características del emisor. Una vez concluida la formación de la unión p-n propiamente dicha, se abordan los problemas relacionados con el crecimiento de la capa de nucleación de GaP. Por un lado, esta capa será la encargada de pasivar la subcélula de silicio, por lo que su crecimiento debe ser regular y homogéneo para que la superficie de silicio quede totalmente pasivada, de tal forma que la velocidad de recombinación superficial en la interfaz GaP/Si sea mínima. Por otro lado, su crecimiento debe ser tal que minimice la aparición de los defectos típicos de una heteroepitaxia de una capa polar sobre un substrato no polar -denominados dominios de antifase-. En el Capítulo 5 se exploran diferentes rutinas de nucleación, dentro del gran abanico de posibilidades existentes, para conseguir una capa de GaP con una buena calidad morfológica y estructural, que será analizada mediante diversas técnicas de caracterización microscópicas. La última parte de esta Tesis está dedicada al estudio de las propiedades fotovoltaicas de la célula inferior. En ella se analiza la evolución de los tiempos de vida de portadores minoritarios de la base durante dos etapas claves en el desarrollo de la estructura Ill-V/Si: la formación de la célula inferior y el crecimiento de las capas III-V. Este estudio se ha llevado a cabo en colaboración con la Universidad de Ohio, que cuentan con una gran experiencia en el crecimiento de materiales III-V sobre silicio. Esta tesis concluye destacando las conclusiones globales del trabajo realizado y proponiendo diversas líneas de trabajo a emprender en el futuro. ABSTRACT This thesis pursues the development and growth of hybrid solar cells -through Metal Organic Vapor Phase Epitaxy (MOVPE)- formed by III-V semiconductors on silicon substrates. This integration aims to provide an alternative to current III-V cells, which, despite hold the efficiency record for photovoltaic devices, their cost is, today, too high to be economically competitive to conventional silicon cells. Accordingly, the target of this project is to link the already demonstrated efficiency potential of III-V semiconductor multijunction solar cell architectures with the low cost and unconstrained availability of silicon substrates. Within the existing alternatives for the integration of III-V semiconductors on silicon substrates, this thesis is based on the metamorphic approach for the development of GaAsP/Si dual-junction solar cells. In this approach, the accommodation of the lattice mismatch is handle through the appearance of crystallographic defects (namely dislocations), which will be confined through the incorporation of a graded buffer layer. The resulting surface will have, on the one hand a good structural quality; and on the other hand the desired lattice parameter. Different research groups have been working in the last years in a structure similar to the one here described, being most of their efforts directed towards the optimization of the heteroepitaxial growth of III-V compounds on Si, with the primary goal of minimizing the appearance of crystal defects. However, none of these groups has paid much attention to the development and optimization of the bottom silicon cell, which, indeed, will play an important role on the overall solar cell performance. In this respect, the idea of this thesis is to complete the work done so far in this field by focusing on the design and optimization of the bottom silicon cell, to harness its efficiency. This work is divided into six chapters, organized according to the natural progress of the bottom cell development. After a brief introduction to the growth of III-V semiconductors on Si substrates, pointing out the different alternatives for their integration; we move to the experimental part, which is initiated by an extensive description and characterization of silicon substrates -the base of the III-V structure-. In this chapter, a comprehensive analysis of the different treatments (chemical and thermal) required for preparing silicon surfaces for subsequent epitaxial growth is presented. Next step on the development of the bottom cell is the formation of the p-n junction itself, which is faced in Chapter 3. Firstly, the optimization of the emitter configuration (in terms of doping and thickness) is handling by analytic models. This study includes a comparison between the different alternatives for the emitter formation, evaluating the advantages and disadvantages of each approach. After the theoretical design of the emitter, it is defined (through the modeling of the P-in-Si diffusion process) a practical parameter space for the experimental implementation of this emitter configuration. The characterization of these emitters through different analytical tools (i.e. ECV or SIMS) will validate and provide experimental support for the theoretical models. A side effect of the formation of the emitter by P diffusion is the roughening of the Si surface. Accordingly, once the p-n junction is formed, it is necessary to ensure that the Si surface is smooth enough and clean for subsequent phases. Indeed, the roughness of the Si must be carefully controlled since it will be the basis for the epitaxial growth. Accordingly, after quantifying (experimentally and by theoretical models) the impact of the phosphorus on the silicon surface morphology, different alternatives for the recovery of the surface are proposed in order to achieve a sub-nanometer roughness which does not endanger the quality of the incoming III-V layers. Moving a step further in the development of the Ill-V/Si structure implies to address the challenges associated to the GaP on Si nucleation. On the one hand, this layer will provide surface passivation to the emitter. In this sense, the growth of the III-V layer must be homogeneous and continuous so the Si emitter gets fully passivated, providing a minimal surface recombination velocity at the interface. On the other hand, the growth should be such that the appearance of typical defects related to the growth of a polar layer on a non-polar substrate is minimized. Chapter 5 includes an exhaustive study of the GaP on Si nucleation process, exploring different nucleation routines for achieving a high morphological and structural quality, which will be characterized by means of different microscopy techniques. Finally, an extensive study of the photovoltaic properties of the bottom cell and its evolution during key phases in the fabrication of a MOCVD-grown III-V-on-Si epitaxial structure (i.e. the formation of the bottom cell; and the growth of III-V layers) will be presented in the last part of this thesis. This study was conducted in collaboration with The Ohio State University, who has extensive experience in the growth of III-V materials on silicon. This thesis concludes by highlighting the overall conclusions of the presented work and proposing different lines of work to be undertaken in the future.

Linked Data Rights 2.0: extension of ODRL for Licensing Linked Data

Linked Data assets (RDF triples, graphs, datasets, mappings...) can be object of protection by the intellectual property law, the database law or its access or publication be restricted by other legal reasons (personal data pro- tection, security reasons, etc.). Publishing a rights expression along with the digital asset, allows the rightsholder waiving some or all of the IP and database rights (leaving the work in the public domain), permitting some operations if certain conditions are satisfied (like giving attribution to the author) or simply reminding the audience that some rights are reserved.

Madera termo-tratada de frondosas para uso estructural

La madera termotratada es madera modificada mediante un proceso térmico a elevadas temperaturas que le proporciona mayor estabilidad dimensional y durabilidad sin incorporar productos químicos perjudiciales para el medio ambiente. Hasta el momento se ha aplicado fundamentalmente a madera de coniferas por motivos económicos, siendo su uso más habitual en ambientes exteriores o de elevada humedad, como elementos de revestimiento no estructurales, carpinterías, mobiliario de jardín, etc. En la presente tesis se estudia la viabilidad de la madera termotratada de frondosas para uso estructural, en particular fresno (Fraxinus excelsior L) y haya (Fagus sylvatica L). Con este fin, y considerando que el termotratamiento modifica la estructura interna de la madera resultando en un nuevo material, se realizan estudios experimentales y numéricos para su caracterización. Estos trabajos se desarrollan bajo el enfoque de la Mecánica de Fractura debido a la pérdida de resistencia y aumento de fragilidad que presenta el material, especialmente a tracción perpendicular a las fibras. Así mismo, se lleva a cabo una recopilación de las bases, fundamentos y metodologías de esta teoría aplicados a madera sin tratar y otros materiales debido a la inexistencia de este tipo de estudios en madera termotratada. De igual manera se realiza un programa de caracterización mecánica del material para determinar sus propiedades elásticas considerando un modelo ortótropo, necesarios en la investigación del comportamiento a fractura. El trabajo derivó en el desarrollo de un nuevo método de ensayo para la determinación multiparamétrica a partir de un sólo espécimen, proporcionando resultados mucho más robustos que los obtenidos con la metodología convencional de ensayos. En base a los trabajos realizados, considerando las limitaciones de resistencia y fragilidad, así como la dudosa aplicabilidad de las normativas existentes en madera sin tratar, se aconseja no utilizar tratamientos térmicos intensos en elementos estructurales primarios. Se propone su aplicación en elementos secundarios, de manera que un posible colapso no implique una pérdida de fiabilidad global de la estructura. Se estudia la viabilidad de un panel sandwich innovador y ecológico para fachadas expuesto a cargas de viento, compuesto de madera termotratada en las caras y panel aislante de fibras de madera con función estructural en el alma. Esta investigación se desarrolló dentro del proyecto de investigación Europeo "Holiwood", Holistic implementation of European thermal treated hardwood (TMT) in the sector of construction industry and noise protection by sustainable, knowledge-based and value added products, perteneciente al sexto Programa Marco. ABSTRACT Hcat-trcatcd wood is modified wood by a thermal process at high temperatures which provides greater dimensional stability and durability without adding harmful chemicals to the environment. It has been mainly applied to softwoods due mainly to economical reasons, being its most common use outdoors or in high humidity environments, as non-structural elements, furniture, etc. The present Thesis studies the feasibility of heat-treated hardwoods for structural uses, particularly ash (Fraxinus excelsior L) and beech (Fagus sylvatica L). To this end, and considering that heat treatment modifies the internal structure of the wood resulting in a new material, experimental and numerical studies are performed for its characterization. This investigation is developed under the approach of Fracture Mechanics due to the loss of strength and the increase in brittlcncss of the material, especially in tension perpendicular to the grain. Likewise, it holds a collection of the bases, foundations and methodologies of this theory applied to untreated wood and other materials due to the lack of such studies in heat-treated wood. In addition, studies for the mechanical characterization of the material are performed in order to determine the elastic properties considering an orthotropic model. This work is necessary in the investigation of the fracture behavior. It led to the development of a new test method for multiparameter determination by using just a single specimen, providing much more robust results than those obtained with conventional test methodology. Based on this investigation, and considering the limitations of strength and brittleness, and the questionable applicability of existing standards for untreated wood, it is advised not to use intense heat treatments in primary structural elements. It is proposed the application to secondary elements, so that a possible collapse does not involve a loss of overall reliability of the structure. It is studied the feasibility of an innovative and ecological sandwich panel for facades exposed to wind loads, composed by heat-treated wood faces and insulating wood fiberboard with structural function in the core. This investigación was developed within the European research project "Holiwood", Holistic implementation of European thermal treated hardwood (TMT) in the sector of construction industry and noise protection by sustainable, knowledge-based and value added products, of the Sixth Framework Program.

Modelización de procesos de soldadura (GMAW y GTAW) de la aleación de magnesio AZ31B. Estudio y análisis del comportamiento de este tipo de uniones soldadas frente a la corrosión en medios salinos

El magnesio y sus aleaciones representan un interesante campo de investigación dentro de la ingeniería de materiales debido a los retos que plantean tanto su conformabilidad como durabilidad. Las características físicas y mecánicas del magnesio y sus aleaciones los convierten en materiales de gran interés desde el punto de vista industrial al tratarse de uno de los materiales más abundantes y ligeros en un mundo en el que día a día los recursos y materias primas son más escasos por lo que el acceso a materiales abundantes y ligeros que permitan economizar el uso de energía cobrará mayor importancia en el futuro. En la coyuntura actual es por tanto necesario revisar procesos y procedimientos, investigando y tratando de ampliar desde este punto de vista si es posible mejorar los procedimientos de fabricación de los materiales disponibles actualmente o el desarrollo de nuevos, mejores que los anteriores, que permitan ayudar a la sostenibilidad del planeta. El magnesio, pese a ser un material muy abundante y relativamente barato, presenta una serie de inconvenientes que limitan de manera muy seria su aplicación industrial, su alta reactividad en presencia de oxígeno y su mal comportamiento frente a la corrosión así como limitaciones en su conformabilidad han estado limitando su uso y aplicaciones, los investigaciones dentro del campo de la metalurgia física de este material y el desarrollo de nuevas aleaciones han permitido su empleo en múltiples aplicaciones dentro de la industria aeroespacial, militar, automovilística, electrónica, deportiva y médica. La motivación para esta tesis doctoral ha sido tratar de aportar más luz sobre el comportamiento de una de las aleaciones comerciales base magnesio más empleadas, la AZ31B, tratando de modelizar como le afectan los procesos de soldadura y estudiando desde un punto de vista experimental como se ve modificada su microestructura, su comportamiento mecánico y su resistencia frente a la corrosión. Aunque en un principio se pensó en el empleo de métodos electroquímicos para el estudio de la corrosión de estos materiales, rápidamente se decidió prescindir de su uso dada la dificultad observada tanto durante los trabajos de investigación de esta Tesis como los encontrados por otros investigadores. Mediante microdurezas se han caracterizado mecánicamente las soldaduras de aleación de magnesio tipo AZ31 en función de diferentes materiales de aporte, observándose que el empleo de las aleaciones con mayor contenido de aluminio y zinc no contribuye a una mejora significativa de las propiedades mecánicas. Se han podido establecer correlaciones entre los modelos de simulación desarrollados y las microestructuras resultantes de los procesos reales de soldadura que permiten definir a priori que estructuras se van a obtener. De igual forma ha sido posible completar un estudio micrográfico y químico completo de las diferentes fases y microconstituyentes originados durante los procesos de soldadura, gracias a estos resultados se ha propuesto como hipótesis una explicación que justifica el comportamiento frente a la corrosión de estas aleaciones una vez soldadas. Los ensayos de corrosión realizados han permitido determinar correlaciones matemáticas que indican las velocidades de corrosión esperables de este tipo de aleaciones. Desde el punto de vista del diseño, los resultados obtenidos en este trabajo permitirán a otros investigadores y diseñadores tomar decisiones a la hora de decidir qué materiales de aporte emplear junto con las implicaciones que conllevan desde el punto de vista metalúrgico, mecánico o corrosivo las diferentes alternativas. Por último indicar que gracias al trabajo desarrollado se han definido modelos matemáticos para predecir el comportamiento frente a la corrosión de estas aleaciones, se han determinado las posibles causas y mecanismos por las que se gobierna la corrosión en la soldadura de chapas de aleación AZ31B y los motivos por los que se debe considerar el empleo de un material de aporte u otro. Los modelos de simulación desarrollados también han ayudado a comprender mejor la microestructura resultante de los procesos de soldadura y se han determinado que fases y microconstituyentes están presentes en las soldaduras de estas aleaciones. ABSTRACT Magnesium and its alloys represent and interesting research field in the material science due to the challenges of their fabrication and durability. The physical and mechanical properties of magnesium and its alloys make them a very interesting materials from and industrial point of view being one of the most abundant and lightest materials in a world in which day by day the lacking of resources and raw materials is more important, the use of light materials which allow to save energy will become more important in a near future. So that it is necessary to review processes and procedures, investigating and trying to improve current fabrication procedures and developing new ones, better than the former ones, in order to help with the sustainability of the planet. Although magnesium is a very common and relatively cheap material, it shows some inconveniences which limit in a major way their industrial application; its high reactivity in presence of oxygen, its poor corrosion resistance and some manufacturing problems had been limiting their use and applications, metallurgical investigations about this material and the development of new alloys have allowed its use in multiple applications in the aerospacial, military, automobile, electronics, sports and medical industry. The motivation for this thesis has been trying to clarify the behavior of one most used commercial base magnesium alloys, the AZ31, trying to modeling how its affected by thermal cycles of the welding process and studying from an experimental point of view how its microstructure is modified and how these modifications affect its mechanical behavior and corrosion resistance. Although at the beginning of this works it was though about the using of electrochemical techniques to evaluate the corrosion of these materials, rapidly it was decided not to use them because of the difficulty observed by during this research and by other investigators. The results obtained in this thesis have allowed to characterize mechanically AZ31 magnesium welding alloys considering different filler metals, according to this study using filler metals with a high content of aluminum and zinc does not represent an important improve It has been possible to establish correlations between simulation models and the resultant microstructures of the real melting processes originated during welding processes which allow to predict the structures which will be obtained after the welding. In addition to that it is possible to complete a complete micrographic and chemical analysis of the different phases and microconstituents created during welding, due to these results and hypothesis to explain the corrosion behavior of these welded alloys. Corrosion tests carried out have allowed defining mathematical correlations to predict corrosion rates of this kind of alloys. From a designing point of view, the results obtained in this work will let other investigators and designers to make decisions taking into account which implications have the different options from a metallurgical, mechanic and corrosive point of view. Finally we would like to indicate that thanks to this work it has been possible to define mathematical models to predict the corrosion behavior, the causes and the mechanism of this corrosion in the AZ31 welding sheets have been also determined and the reasons for using of one filler metal or another, the developed simulation models have also help to get a better understanding of the result microstructure determining the phases and the microconstituents present in the welding of this alloys.

Improvement of root architecture under abiotic stress through control of auxin homeostasis in Arabidopsis and Brassica crops

Auxin plays an important role in many aspects of plant development including stress responses. Here we briefly summarize how auxin is involved in salt stress, drought (i.e. mostly osmotic stress), waterlogging and nutrient deficiency in Brassica plants. In addition, some mechanisms to control auxin levels and signaling in relation to root formation (under stress) will be reviewed. Molecular studies are mainly described for the model plant Arabidopsis thaliana, but we also like to demonstrate how this knowledge can be transferred to agriculturally important Brassica species, such as Brassica rapa, Brassica napus and Brassica campestris. Moreover, beneficial fungi could play a role in the adaptation response of Brassica roots to abiotic stresses. Therefore, the possible influence of Piriformospora indica will also be covered since the growth promoting response of plants colonized by P. indica is also linked to plant hormones, among them auxin.