Safety and health in forest harvesting operations. Diagnosis and preventive actions. A review

Aim of study: to review the present state of the art in relation to the main labour risks and the most relevant results of recent studies evaluating the safety and health conditions of the forest harvesting work and better ways to reduce accidents. Area of study: It focuses mainly on developed Countries, where the general concern about work risks prevention, together with the complex idiosyncrasy of forest work in forest harvesting operations, has led to a growing interest from the forest scientific and technical community. Material and Methods: The main bibliographic and Internet references have been identified using common reference analysis tools. Their conclusions and recommendations have been comprehensively summarized. Main results: Collection of the principal references and their most important conclusions relating to the main accident risk factors, their causes and consequences, the means used towards their prevention, both instrumental as well as in the aspects of training and business management, besides the influence of the growing mechanization of logging operations on those risks. Research highlights: Accident risk is higher in forest harvesting than in most other work sectors, and the main risk factors such as experience, age, seasonality, training, protective equipment, mechanization degree, etc. have been identified and studied. The paper summarizes some relevant results, one of the principal being that the proper entrepreneurial risk management is a key factor leading to the success in minimizing labour risks..

Accident Management Actions In An Upper-Head Small-Break Loss-Of-Coolant Accident With High-Pressure Safety Injection Failed

Since the Three Mile Island accident, an important focus of pressurized water reactor (PWR) transient analyses has been a small-break loss-of-coolant accident (SBLOCA). In 2002, the discovery of thinning of the vessel head wall at the Davis Besse nuclear power plant reactor indicated the possibility of an SBLOCA in the upper head of the reactor vessel as a result of circumferential cracking of a control rod drive mechanism penetration nozzle - which has cast even greater importance on the study of SBLOCAs. Several experimental tests have been performed at the Large Scale Test Facility to simulate the behavior of a PWR during an upper-head SBLOCA. The last of these tests, Organisation for Economic Co-operation and Development Nuclear Energy Agency Rig of Safety Assessment (OECD/NEA ROSA) Test 6.1, was performed in 2005. This test was simulated with the TRACE 5.0 code, and good agreement with the experimental results was obtained. Additionally, a broad analysis of an upper-head SBLOCA with high-pressure safety injection failed in a Westinghouse PWR was performed taking into account different accident management actions and conditions in order to check their suitability. This issue has been analyzed also in the framework of the OECD/NEA ROSA project and the Code Applications and Maintenance Program (CAMP). The main conclusion is that the current emergency operating procedures for Westinghouse reactor design are adequate for these kinds of sequences, and they do not need to be modified.

Counting, scoring and classifying hunger to allocate resources targeted to solve the problem

A proper allocation of resources targeted to solve hunger is essential to optimize the efficacy of actions and maximize results. This requires an adequate measurement and formulation of the problem as, paraphrasing Einstein, the formulation of a problem is essential to reach a solution. Different measurement methods have been designed to count, score, classify and compare hunger at local level and to allow comparisons between different places. However, the alternative methods produce significantly reach different results. These discrepancies make decisions on the targeting of resource allocations difficult. To assist decision makers, a new method taking into account the dimension of hunger and the coping capacities of countries, is proposed enabling to establish both geographical and sectoral priorities for the allocation of resources.

Counting, scoring and classifying hunger to allocate resources targeted to solve the problem

A proper allocation of resources targeted to solve hunger is essential to optimize the efficacy of actions and maximize results. This requires an adequate measurement and formulation of the problem as, paraphrasing Einstein, the formulation of a problem is essential to reach a solution. Different measurement methods have been designed to count, score, classify and compare hunger at local level and to allow comparisons between different places. However, the alternative methods reach significantly different results. These discrepancies make decisions on the targeting of resource allocations difficult. To assist decision makers, a new method taking into account the dimension of hunger and the coping capacities of countries is proposed enabling to establish both geographical and sectoral priorities for the allocation of resources

Diagnosing Causes of Water Scarcity in Complex Water Resources Systems and Identifying Risk Management Actions

From the water management perspective, water scarcity is an unacceptable risk of facing water shortages to serve water demands in the near future. Water scarcity may be temporary and related to drought conditions or other accidental situation, or may be permanent and due to deeper causes such as excessive demand growth, lack of infrastructure for water storage or transport, or constraints in water management. Diagnosing the causes of water scarcity in complex water resources systems is a precondition to adopt effective drought risk management actions. In this paper we present four indices which have been developed to evaluate water scarcity. We propose a methodology for interpretation of index values that can lead to conclusions about the reliability and vulnerability of systems to water scarcity, as well as to diagnose their possible causes and to propose solutions. The described methodology was applied to the Ebro river basin, identifying existing and expected problems and possible solutions. System diagnostics, based exclusively on the analysis of index values, were compared with the known reality as perceived by system managers, validating the conclusions in all cases

Recommendations on seismic actions on bridges

The paper describes the main features of a technical Recommendation first draft on Seismic Actions on Bridges, promoted by the Spanish Ministry of Public Works (MOPT). Although much more research is needed to clarify the seismic behaviour of the vast class of problems present in port structures the current state of the art allows at least a classificaton of subjects and the establishment of minimum requirements to guide the design. Also the use of more refined methods for specially dangerous situations needs some general guidelines that contribute to mantein the design under reasonable safety margins. The Recommendations of the Spanish MOPT are a first try in those directions.

Recommendations on seismic actions on port structures

The paper describes the main features of a Technical Recommendation first draft on Seismic Action on port structures promoted recently by the Spanish Ministry of Public Works (MOPT). Although much more research is needed to clarify the seismic behaviour of the vast class of problems present in port structures the current state of the art allows at least a classification of subjects and the establishment of minimum requirements to guide the design. Also the use of more refined methods for specially dangerous situations needs some general guidelines that contribute to mantein the design under reasonable safety margins. The Recommendations of the Spanish MOPT are a first try in those directions.

Experimental and numerical analysis of reinforced concrete elements subjected to blast loading

El hormigón es uno de los materiales de construcción más empleados en la actualidad debido a sus buenas prestaciones mecánicas, moldeabilidad y economía de obtención, entre otras ventajas. Es bien sabido que tiene una buena resistencia a compresión y una baja resistencia a tracción, por lo que se arma con barras de acero para formar el hormigón armado, material que se ha convertido por méritos propios en la solución constructiva más importante de nuestra época. A pesar de ser un material profusamente utilizado, hay aspectos del comportamiento del hormigón que todavía no son completamente conocidos, como es el caso de su respuesta ante los efectos de una explosión. Este es un campo de especial relevancia, debido a que los eventos, tanto intencionados como accidentales, en los que una estructura se ve sometida a una explosión son, por desgracia, relativamente frecuentes. La solicitación de una estructura ante una explosión se produce por el impacto sobre la misma de la onda de presión generada en la detonación. La aplicación de esta carga sobre la estructura es muy rápida y de muy corta duración. Este tipo de acciones se denominan cargas impulsivas, y pueden ser hasta cuatro órdenes de magnitud más rápidas que las cargas dinámicas impuestas por un terremoto. En consecuencia, no es de extrañar que sus efectos sobre las estructuras y sus materiales sean muy distintos que las que producen las cargas habitualmente consideradas en ingeniería. En la presente tesis doctoral se profundiza en el conocimiento del comportamiento material del hormigón sometido a explosiones. Para ello, es crucial contar con resultados experimentales de estructuras de hormigón sometidas a explosiones. Este tipo de resultados es difícil de encontrar en la literatura científica, ya que estos ensayos han sido tradicionalmente llevados a cabo en el ámbito militar y los resultados obtenidos no son de dominio público. Por otra parte, en las campañas experimentales con explosiones llevadas a cabo por instituciones civiles el elevado coste de acceso a explosivos y a campos de prueba adecuados no permite la realización de ensayos con un elevado número de muestras. Por este motivo, la dispersión experimental no es habitualmente controlada. Sin embargo, en elementos de hormigón armado sometidos a explosiones, la dispersión experimental es muy acusada, en primer lugar, por la propia heterogeneidad del hormigón, y en segundo, por la dificultad inherente a la realización de ensayos con explosiones, por motivos tales como dificultades en las condiciones de contorno, variabilidad del explosivo, o incluso cambios en las condiciones atmosféricas. Para paliar estos inconvenientes, en esta tesis doctoral se ha diseñado un novedoso dispositivo que permite ensayar hasta cuatro losas de hormigón bajo la misma detonación, lo que además de proporcionar un número de muestras estadísticamente representativo, supone un importante ahorro de costes. Con este dispositivo se han ensayado 28 losas de hormigón, tanto armadas como en masa, de dos dosificaciones distintas. Pero además de contar con datos experimentales, también es importante disponer de herramientas de cálculo para el análisis y diseño de estructuras sometidas a explosiones. Aunque existen diversos métodos analíticos, hoy por hoy las técnicas de simulación numérica suponen la alternativa más avanzada y versátil para el cálculo de elementos estructurales sometidos a cargas impulsivas. Sin embargo, para obtener resultados fiables es crucial contar con modelos constitutivos de material que tengan en cuenta los parámetros que gobiernan el comportamiento para el caso de carga en estudio. En este sentido, cabe destacar que la mayoría de los modelos constitutivos desarrollados para el hormigón a altas velocidades de deformación proceden del ámbito balístico, donde dominan las grandes tensiones de compresión en el entorno local de la zona afectada por el impacto. En el caso de los elementos de hormigón sometidos a explosiones, las tensiones de compresión son mucho más moderadas, siendo las tensiones de tracción generalmente las causantes de la rotura del material. En esta tesis doctoral se analiza la validez de algunos de los modelos disponibles, confirmando que los parámetros que gobiernan el fallo de las losas de hormigón armado ante explosiones son la resistencia a tracción y su ablandamiento tras rotura. En base a los resultados anteriores se ha desarrollado un modelo constitutivo para el hormigón ante altas velocidades de deformación, que sólo tiene en cuenta la rotura por tracción. Este modelo parte del de fisura cohesiva embebida con discontinuidad fuerte, desarrollado por Planas y Sancho, que ha demostrado su capacidad en la predicción de la rotura a tracción de elementos de hormigón en masa. El modelo ha sido modificado para su implementación en el programa comercial de integración explícita LS-DYNA, utilizando elementos finitos hexaédricos e incorporando la dependencia de la velocidad de deformación para permitir su utilización en el ámbito dinámico. El modelo es estrictamente local y no requiere de remallado ni conocer previamente la trayectoria de la fisura. Este modelo constitutivo ha sido utilizado para simular dos campañas experimentales, probando la hipótesis de que el fallo de elementos de hormigón ante explosiones está gobernado por el comportamiento a tracción, siendo de especial relevancia el ablandamiento del hormigón. Concrete is nowadays one of the most widely used building materials because of its good mechanical properties, moldability and production economy, among other advantages. As it is known, it has high compressive and low tensile strengths and for this reason it is reinforced with steel bars to form reinforced concrete, a material that has become the most important constructive solution of our time. Despite being such a widely used material, there are some aspects of concrete performance that are not yet fully understood, as it is the case of its response to the effects of an explosion. This is a topic of particular relevance because the events, both intentional and accidental, in which a structure is subjected to an explosion are, unfortunately, relatively common. The loading of a structure due to an explosive event occurs due to the impact of the pressure shock wave generated in the detonation. The application of this load on the structure is very fast and of very short duration. Such actions are called impulsive loads, and can be up to four orders of magnitude faster than the dynamic loads imposed by an earthquake. Consequently, it is not surprising that their effects on structures and materials are very different than those that cause the loads usually considered in engineering. This thesis broadens the knowledge about the material behavior of concrete subjected to explosions. To that end, it is crucial to have experimental results of concrete structures subjected to explosions. These types of results are difficult to find in the scientific literature, as these tests have traditionally been carried out by armies of different countries and the results obtained are classified. Moreover, in experimental campaigns with explosives conducted by civil institutions the high cost of accessing explosives and the lack of proper test fields does not allow for the testing of a large number of samples. For this reason, the experimental scatter is usually not controlled. However, in reinforced concrete elements subjected to explosions the experimental dispersion is very pronounced. First, due to the heterogeneity of concrete, and secondly, because of the difficulty inherent to testing with explosions, for reasons such as difficulties in the boundary conditions, variability of the explosive, or even atmospheric changes. To overcome these drawbacks, in this thesis we have designed a novel device that allows for testing up to four concrete slabs under the same detonation, which apart from providing a statistically representative number of samples, represents a significant saving in costs. A number of 28 slabs were tested using this device. The slabs were both reinforced and plain concrete, and two different concrete mixes were used. Besides having experimental data, it is also important to have computational tools for the analysis and design of structures subjected to explosions. Despite the existence of several analytical methods, numerical simulation techniques nowadays represent the most advanced and versatile alternative for the assessment of structural elements subjected to impulsive loading. However, to obtain reliable results it is crucial to have material constitutive models that take into account the parameters that govern the behavior for the load case under study. In this regard it is noteworthy that most of the developed constitutive models for concrete at high strain rates arise from the ballistic field, dominated by large compressive stresses in the local environment of the area affected by the impact. In the case of concrete elements subjected to an explosion, the compressive stresses are much more moderate, while tensile stresses usually cause material failure. This thesis discusses the validity of some of the available models, confirming that the parameters governing the failure of reinforced concrete slabs subjected to blast are the tensile strength and softening behaviour after failure. Based on these results we have developed a constitutive model for concrete at high strain rates, which only takes into account the ultimate tensile strength. This model is based on the embedded Cohesive Crack Model with Strong Discontinuity Approach developed by Planas and Sancho, which has proved its ability in predicting the tensile fracture of plain concrete elements. The model has been modified for its implementation in the commercial explicit integration program LS-DYNA, using hexahedral finite elements and incorporating the dependence of the strain rate, to allow for its use in dynamic domain. The model is strictly local and does not require remeshing nor prior knowledge of the crack path. This constitutive model has been used to simulate two experimental campaigns, confirming the hypothesis that the failure of concrete elements subjected to explosions is governed by their tensile response, being of particular relevance the softening behavior of concrete.

The impact of sustainable construction and knowledge management on sustainability goals. A review of the venezuelan renewable energy sector

The recognition of the relevance of energy, especially of the renewable energies generated by the sun, water, wind, tides, modern biomass or thermal is growing significantly in the global society based on the possibility it has to improve societies′ quality of life, to support poverty reduction and sustainable development. Renewable energy, and mainly the energy generated by large hydropower generation projects that supply most of the renewable energy consumed by developing countries, requires many technical, legal, financial and social complex processes sustained by innovations and valuable knowledge. Besides these efforts, renewable energy requires a solid infrastructure to generate and distribute the energy resources needed to solve the basic needs of society. This demands a proper construction performance to deliver the energy projects planned according to specifications and respecting environmental and social concerns, which implies the observance of sustainable construction guidelines. But construction projects are complex and demanding and frequently face time and cost overruns that may cause negative impacts on the initial planning and thus on society. The renewable energy issue and the large renewable energy power generation and distribution projects are particularly significant for developing countries and for Latin America in particular, as this region concentrates an important hydropower potential and installed capacity. Using as references the performance of Venezuelan large hydropower generation projects and the Guri dam construction, this research evaluates the tight relationship existing between sustainable construction and knowledge management and their impact to achieve sustainability goals. The knowledge management processes are proposed as a basic strategy to allow learning from successes and failures obtained in previous projects and transform the enhancement opportunites into actions to improve the performance of the renewable energy power generation and distribution projects.

On the Use of Situational and Body Information in Goalkeeper Actions during a Soccer Penalty Kick

Artículo Experimental

Consultoría en el marco económico-financiero de la empresa

Muchas de las grandes iniciativas empresariales, se ven truncadas por falta de un adecuado análisis económico-financiero. Incluso, muchas grandes ideas no son implantadas correctamente en el primer intento por este motivo, y son otras personas las que consiguen posteriormente el éxito de esas brillantes ideas gracias a una correcta aproximación financiera. Las empresas necesitan definir sus objetivos, establecer las para lograrlos, identificar las personas responsables de su ejecución (sus roles y funciones) y elaborar un plan económico-financiero que recoja el estudio de inversiones necesarias, el análisis de costes, la previsión de ingresos, así como la estrategia financiera más adecuada para la captación de los fondos necesarios para llevar a cabo las acciones programadas. Una vez iniciado el proyecto empresarial, será imprescindible realizar un seguimiento y control de la evolución (integración), tomando las medidas que se estimen oportunas para mantener el rumbo adecuado durante todo el tiempo de actividad. En este trabajo, aplicaremos las metodologías y buenas prácticas de la gestión de proyectos, como marco estructurado que nos permita abordar las principales cuestiones económico-financieras a tener en cuenta a la hora de enfrentarnos a un proyecto empresarial, para contribuir, en la medida de lo posible, a que los emprendedores tengan en cuenta estas cuestiones, facilitando así el desarrollo de negocios, en un difícil entorno económico de crisis como el que actualmente estamos viviendo en España, y animando de esta manera a optar por la iniciativa emprendedora, tratando de minimizar el riesgo en base al contenido. ---ABSTRACT---Lack of adequate economic and financial analysis truncates many of the entrepreneurship and innovation programs. Because of that reason, many great ideas are not even correctly implemented on the first attempt, and the person who finds the proper financial approach, succeed. All the enterprises have to establish clear objectives, actions to accomplish those objectives, assign roles, responsibilities and executive functions to specific people. Elaborate funding plan that contains surveys on necessary investments, cost analysis, estimate the income, liquid assets and also financial strategy suitable for fundraising to finance programmed actions. Once the project has been executed it is essential to monitor and control the development and integration adopting measures accordingly to the needs. This thesis applies methodology and best practice of project management as structured framework for the principal economic and financial issues facing business project. It is necessary contribution to entrepreneurs understanding of business, therefore facilitates business development in such rough environment as Spain is at this moment, and at the same time encourages adopting entrepreneur’s solution as less risky one. This document aims to explore all the economic and financial issues from methodological point of view based on my own professional experience, resulting in helping to understand the importance that economy and finances have in developing adequate corporate strategy. Crisis has highlighted inadequate functionality of many companies. Most popular first symptom is lack of cash flow that deteriorates the company, and results in suspension of payments followed by closing. In other cases, difficulties appear due to poor financial management of committed resources; to be observed in lack of prevision and planning or incorrect basic functionality and operational matters on daily basis. What would be your advice to someone who have magnificent business idea however no knowledge on how to handle finances in order to succeed in initiating and executing the project? Despite of the fact that the central nucleus of this paper is at economics and finances area, all the other concepts and topics given during master will be revived; for example business strategy, consultants abilities, organization and standard processes, among others, are impregnated with knowledge of project management.

The impact of the economic crisis and policy actions on GHG emissions from road transport in Spain

Road traffic is the greatest contributor to the carbon footprint of the transport sector and reducing it has become one of the main targets of sustainable transport policies. An analysis of the main factors influencing greenhouse gas (GHG) emissions is essential for designing new energy- and environmentally efficient strategies for the road transport. This paper addresses this need by (i) identifying factors which influence the carbon footprint, including traffic activity, fuel economy and socioeconomic development; and (ii) proposing a methodological framework which uses Modified Laspeyres Index decomposition to analyze the effect of important drivers on the changes in emissions of road transport in Spain during the period from 1990 to 2010. The results demonstrate that the country׳s economic growth has been closely linked to the rise in GHG emissions. The innovative contribution of this paper is the special analysis of the changes in mobility patterns and GHG emissions during the economic crisis, when, for the first time, Spanish road traffic emissions decreased. The reduction of road transport and improved energy efficiency has been powerful contributors to this decrease, demonstrating the effectiveness of energy-saving measures. On the basis of this analysis, several tailored policy recommendations have been suggested for future implementation.

Modeling of dangerous phenomena and innovative techniques for hazard evaluation and risk mitigation

Society is frequently exposed to and threatened by dangerous phenomena in many parts of the world. Different types of such phenomena require specific actions for proper risk management, from the stages of hazard identification to those of mitigation (including monitoring and early-warning) and/or reduction. The understanding of both predisposing factors and triggering mechanisms of a given danger and the prediction of its evolution from the source to the overall affected zone are relevant issues that must be addressed to properly evaluate a given hazard.

A Schwarz lemma for Kahler affine metrics and the canonical potential of a proper convex cone

This is an account of some aspects of the geometry of Kahler affine metrics based on considering them as smooth metric measure spaces and applying the comparison geometry of Bakry-Emery Ricci tensors. Such techniques yield a version for Kahler affine metrics of Yau s Schwarz lemma for volume forms. By a theorem of Cheng and Yau, there is a canonical Kahler affine Einstein metric on a proper convex domain, and the Schwarz lemma gives a direct proof of its uniqueness up to homothety. The potential for this metric is a function canonically associated to the cone, characterized by the property that its level sets are hyperbolic affine spheres foliating the cone. It is shown that for an n -dimensional cone, a rescaling of the canonical potential is an n -normal barrier function in the sense of interior point methods for conic programming. It is explained also how to construct from the canonical potential Monge-Ampère metrics of both Riemannian and Lorentzian signatures, and a mean curvature zero conical Lagrangian submanifold of the flat para-Kahler space.

Propuesta de un sistema para detección precoz de trastornos del lenguaje en niños de 0 a 6 años

Las Tecnologías de la Información y las Comunicaciones han propiciado avances en el contexto de la salud tanto en la gestión efectiva de información socio‐sanitaria de forma electrónica, como en la provisión de servicios de e‐salud y telemedicina. Los antecedentes de investigación publicados en esta área corroboran este hecho presentando las mejoras experimentadas en la atención de la población y en la provisión de servicios sanitarios. La atención temprana, cuyos principios científicos se fundamentan en los campos de la pediatría, neurología, psicología, psiquiatría, pedagogía, fisiatría y lingüística, entre otros, tiene como finalidad ofrecer a los niños con déficit o con riesgo de padecerlos un conjunto de acciones optimizadoras y compensadoras, que faciliten su adecuada maduración en todos los ámbitos y que les permita alcanzar el máximo nivel de desarrollo personal y de integración social. La detección de posibles alteraciones en el desarrollo infantil es un aspecto clave de la atención temprana en la medida en que puede posibilitar la puesta en marcha de diversos mecanismos de actuación disponibles en las entidades implicadas, valiosos para la calidad de vida de la persona. Cuanto antes se realice la detección, existen mayores garantías de prevenir patologías añadidas, lograr mejoras funcionales y posibilitar un ajuste más adaptativo entre el niño y su entorno. El objetivo de la investigación presentada en esta tesis doctoral es analizar, diseñar, verificar y validar un sistema de información abierto, basado en conocimiento, que facilite efectivamente a los profesionales que trabajan con la población infantil entre 0 y 6 años la detección precoz de posibles trastornos del lenguaje. Desde el punto de vista metodológico, la Ingeniería del Conocimiento ofrece un marco conceptual sólido que permite desarrollar y validar Sistemas de Ayuda a la Toma de Decisiones distribuidos y escalables, capaces de ayudar al pediatra de Atención Primaria y al educador infantil en la detección precoz de posibles trastornos del lenguaje en niños. La evaluación del sistema se ha realizado de forma incremental mediante el diseño y validación de pruebas de campo experimentales consistentes en la evaluación de niños en dos escenarios distintos: la escuela infantil y el centro de atención temprana. Los experimentos realizados en poblaciones distintas con alrededor de 344 niños durante 2 años, han permitido contrastar la buena adecuación del sistema propuesto a las necesidades de detección de los profesionales que trabajan con niños entre 0 y 6 años. La tesis resultante ha permitido caracterizar el uso del sistema en entornos reales, conocer la aceptación entre los usuarios y su impacto en la provisión de un servicio de atención temprana como el descrito para el correcto seguimiento del desarrollo del lenguaje en los niños, además de proponer un nuevo modelo de atención y evaluación cooperativa que permita incrementar el conocimiento experimental existente al respecto. ABSTRACT The Information and Communication Technology have led to advances in the context of health both in the effective management of socio‐health information electronically, and in the provision of e‐health and telemedicine. The history of research published in this area confirm this fact by presenting the improvements in the care of the population and the provision of health services. Early attention, whose scientific principles are based on the fields of pediatrics, neurology, psychology, psychiatry, pedagogy, physical medicine and linguistics, among others, aims to provide children with deficits or risk of suffering a set of enhancer actions, which facilitate adequate maturation in all areas and allow them to achieve the highest level of personal development and social integration. The detection of possible changes in child development is a key aspect of early intervention to the extent that it can enable the implementation of different mechanisms of action available to the entities involved, valuable to the quality of life of the person. The earlier the detection is made, there are more guarantees added to prevent diseases, achieving functional improvements and enable a more adaptive fit between the child and his environment. The aim of the research presented is to analyze, design, verify and validate an open information system, based on knowledge, which effectively provide professionals working with the child population between 0 and 6 years, in processes of early detection of language disorders. From the methodological point of view, Knowledge Engineering provides a solid conceptual framework to develop and validate a distributed and scalable decision support systems aim to assist pediatricians and language therapists at early identification and referral of language disorder in childhood. The system evaluation was performed incrementally with the design and validation of consistent experimental field tests in the assessment of children in two different scenarios: the nursery and early intervention center. Experiments in different populations with about 344 children over 2 years, allowed to testing the adequacy of the proposed good detection needs of professionals working with children between 0 and 6 years old system. The resulting thesis has allowed to formalizing the system at real environments and to identifying the acceptance by users as well as its impact on the provision of an early intervention service, such as the one described for the proper monitoring of language development in children. In addition, it proposes a new model of care and cooperative evaluation that lets to increase the existing experimental knowledge about it.