Development of Robotized Laser Welding Applications for Joining Thin Sheets

Laser Welding (LW) is more often used in manufacturing due to its advantages, such as accurate control, good repeatability, less heat input, opportunities for joining of special materials, high speed, capability to join small dimension parts etc. LW is dedicated to robotized manufacturing, and the fabrication cells are using various level of flexibility, from specialized robots to very flexible setups. This paper features several LW applications using two industrially-scaled manufacturing cells at UPM Laser Centre (CLUPM) of Polytechnical University of Madrid (Universidad Politécnica de Madrid). The one dedicated to Remote Laser Welding (RLW) of thin sheets for automotive and other sectors uses a CO2 laser of 3500 W. The second has a high flexibility, is based on a 6-axis ABB robot and a Nd:YAG laser of 3300 W, and is meant for various laser processing methods, including welding. After a short description of each cell, several LW applications experimented at CLUPM and recently implemented in industry are briefly presented: RLW of automotive coated sheets, LW of high strength automotive sheets, LW vs. laser hybrid welding (LHW) of Double Phase steel thin sheets, and LHW of thin sheets of stainless steel and carbon steel (dissimilar joints). The main technological issues overcame and the critical process parameters are pointed out. Conclusions about achievements and trends are provided.

Si(100) versus Ge(100): Watching the interface formation for the growth of III-V-based solar cells on abundant substrates

We investigated the atomic surface properties of differently prepared silicon and germanium (100) surfaces during metal-organic vapour phase epitaxy/chemical vapour deposition (MOVPE/MOCVD), in particular the impact of the MOVPE ambient, and applied reflectance anisotropy/difference spectroscopy (RAS/RDS) in our MOVPE reactor to in-situ watch and control the preparation on the atomic length scale for subsequent III-V-nucleation. The technological interest in the predominant opto-electronic properties of III-V-compounds drives the research for their heteroepitaxial integration on more abundant and cheaper standard substrates such as Si(100) or Ge(100). In these cases, a general task must be accomplished successfully, i.e. the growth of polar materials on non-polar substrates and, beyond that, very specific variations such as the individual interface formation and the atomic step structure, have to be controlled. Above all, the method of choice to grow industrial relevant high-performance device structures is MOVPE, not normally compatible with surface and interface sensitive characterization tools, which are commonly based on ultrahigh vacuum (UHV) ambients. A dedicated sample transfer system from MOVPE environment to UHV enabled us to benchmark the optical in-situ spectra with results from various surfaces science instruments without considering disruptive contaminants. X-ray photoelectron spectroscopy (XPS) provided direct observation of different terminations such as arsenic and phosphorous and verified oxide removal under various specific process parameters. Absorption lines in Fourier-transform infrared (FTIR) spectra were used to identify specific stretch modes of coupled hydrides and the polarization dependence of the anti-symmetric stretch modes distinguished different dimer orientations. Scanning tunnelling microscopy (STM) studied the atomic arrangement of dimers and steps and tip-induced H-desorption proved the saturation of dangling bonds after preparati- n. In-situ RAS was employed to display details transiently such as the presence of H on the surface at lower temperatures (T <; 800°C) and the absence of Si-H bonds at elevated annealing temperature and also surface terminations. Ge buffer growth by the use of GeH4 enables the preparation of smooth surfaces and leads to a more pronounced amplitude of the features in the spectra which indicates improvements of the surface quality.

In situ control of the GE(100)surface domain structure for III-V multijunction solar cells

Vicinal Ge(100) is the common substrate for state of the art multi-junction solar cells grown by metal-organic vapor phase epitaxy (MOVPE). While triple junction solar cells based on Ge(100) present efficiencies mayor que 40%, little is known about the microscopic III-V/Ge(100) nucleation and its interface formation. A suitable Ge(100) surface preparation prior to heteroepitaxy is crucial to achieve low defect densities in the III-V epilayers. Formation of single domain surfaces with double layer steps is required to avoid anti-phase domains in the III-V films. The step formation processes in MOVPE environment strongly depends on the major process parameters such as substrate temperature, H2 partial pressure, group V precursors [1], and reactor conditions. Detailed investigation of these processes on the Ge(100) surface by ultrahigh vacuum (UHV) based standard surface science tools are complicated due to the presence of H2 process gas. However, in situ surface characterization by reflection anisotropy spectroscopy (RAS) allowed us to study the MOVPE preparation of Ge(100) surfaces directly in dependence on the relevant process parameters [2, 3, 4]. A contamination free MOVPE to UHV transfer system [5] enabled correlation of the RA spectra to results from UHV-based surface science tools. In this paper, we established the characteristic RA spectra of vicinal Ge(100) surfaces terminated with monohydrides, arsenic and phosphorous. RAS enabled in situ control of oxide removal, H2 interaction and domain formation during MOVPE preparation.

Stability and mechanical evaluation of bovine pericardium cross-linked with polyurethane prepolymer in aqueous medium

The present study investigates the potential use of non-catalyzed water-soluble blocked polyurethane prepolymer (PUP) as a bifunctional cross-linker for collagenous scaffolds. The effect of concentration (5, 10, 15 and 20%), time (4, 6, 12 and 24 h), medium volume (50, 100, 200 and 300%) and pH (7.4, 8.2, 9 and 10) over stability, microstructure and tensile mechanical behavior of acellular pericardial matrix was studied. The cross-linking index increased up to 81% while the denaturation temperature increased up to 12 °C after PUP crosslinking. PUP-treated scaffold resisted the collagenase degradation (0.167 ± 0.14 mmol/g of liberated amine groups vs. 598 ± 60 mmol/g for non-cross-linked matrix). The collagen fiber network was coated with PUP while viscoelastic properties were altered after cross-linking. The treatment of the pericardial scaffold with PUP allows (i) different densities of cross-linking depending of the process parameters and (ii) tensile properties similar to glutaraldehyde method.

Laser induced forward transfer of silver pastes for printing of fingers in c-si cells.

The main objective of this work is to adapt the Laser Induced Forward Techniques (LIFT), a well- known laser direct writing technique for material transfer, to define metallic contacts (fingers and busbars) onto c-Si cells. The silver paste (with viscosity around 30-50 kcPs) is applied over a glass substrate using a coater. The thickness of the paste can be control changing the deposit parameters. The glass with the silver paste is set at a controlled gap over the c-Si cell. A solid state pulsed laser (532 nm) is focused at the glass/silver interface producing a droplet of silver that it is transferred to the c-Si cell. A scanner is used to print lines. The process parameters (silver paste thickness, gap and laser parameters -spot size, pulse energy and overlapping of pulses) are modified and the morphology of the lines is studied using confocal microscopy. Long lines are printed and the uniformity (in thickness and height) is studied. Some examples of metallization of larger areas (up to 10 cm x 10 cm) are presented.

Diseño para fabricación digital: definición unívoca entre forma y fabricación en arquitectura

La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. Establecida la primera conclusión, el capítulo de contexto histórico continúa enfocándose sobre la aplicación de las técnicas digitales en el Proceso de proyecto primero, y en la puesta en obra después. Los casos de estudio identifican claramente como un punto de inflexión para la generación de formas complejas mediante un software CAD el Museo Guggenheim de Bilbao en 1992. El motivo esencial para elegir este proyecto como el primer proyecto digital es el uso de la herramienta de definición digital de la geometría para su reproducción inequívoca en obra. “La revolución digital ha aportado al Arquitecto la posibilidad de abandonar las tipologías arquitectónicas basados en restricciones geométricas-constructivas. La aplicación de técnicas de fabricación digital ha permitido la capacidad de diseñar con independencia del sistema constructivo y libertad formal. En este nuevo contexto las prestaciones suponen los nuevos límites conceptuales, ya que el acceso y disposición de la información del comportamiento de las alternativas que cada geometría conlleva demanda del Arquitecto la jerarquización de los objetivos y la formulación en un conjunto coherente de parámetros”. Los proyectos que emplean herramientas digitales para la resolución de las distintas etapas del proceso proyectual se verán incrementados de forma exponencial desde 1992 hasta nuestros días. A pesar del importante auge de las técnicas de diseño asistido por ordenador el principal desafío sigue siendo la vinculación de las geometrías y materiales propuestos con las capacidades de las técnicas de manufactura y puesta en obra. El proceso de diseño para fabricación en un entorno digital es una tecnología madura en otras industrias como la aeroespacial o la automovilística, incluso la de productos de consumo y decoración, sin embargo en el sector de Construcción es un sistema inmaduro e inconexo. Las particularidades de la industria de la construcción aún no han sido abordadas en su totalidad y las propuestas de investigación realizadas en este ámbito se han centrado hasta 2015 en partes del proceso y no en el proceso total. “El principal obstáculo para la estandarización e implantación globalizada de un proceso digital desde el origen de la forma hasta la construcción es la inexistencia de un protocolo integrado que integre las limitaciones de fabricación, económicas y de puesta en obra junto a la evaluación de desempeño prestacional durante la fases iniciales de proyecto”. En el capítulo número 3 se estudian los distintos procesos de generación de la forma. Se propone una definición específica para el ámbito de la investigación de “forma” en el entendemos que se incluye la envolvente exterior y el conjunto organizativo de espacios interiores conectados. Por lo tanto no es excluyente del interior. El objetivo de este estudio es analizar y clasificar los procesos para la generación digital de formas en los distintos proyectos seleccionados como emblemáticos de cada tipología. Se concluye que la aproximación a este proceso es muy variada y compleja, con aplicación segregada y descoordinada entre los distintos agentes que han intervenir. En un proceso de generación formal analógico los parámetros que intervienen son en parte conscientes y en parte inconscientes o aprendidos. El Arquitecto sólo tiene control sobre la parte consciente de los parámetros a integrar en el diseño, de acuerdo a sus conocimientos y capacidades será capaz de manejar un número limitado de parámetros. La parte aprendida permanece en el inconsciente y dirige el proceso analógico, aportando prejuicios estéticos incorporados durante el proceso formativo y propio del entorno cultural. “El empleo de herramientas digitales basadas en la evaluación prestacional durante el proceso de selección formal permite al Arquitecto conocer “en tiempo real” el desempeño en el conjunto de prestaciones evaluadoras del conjunto de alternativas geométricas a la propuesta previamente definida por la intuición arquitectónica. El proceso definido no persigue identificar una solución óptima sino asistir al Arquitecto en el proceso de generación de la forma mediante la evaluación continua de los vectores direccionales más idóneos que el procedimiento generativo plantea”. La definición de complejidad en generación y producción de formas en relación con el proceso de diseño digital paramétrico global o integrado, es esencial para establecer un protocolo que optimice su gestión. “Se propone como definición de complejidad como factor resultante de multiplicar el número de agentes intervinientes por el número de parámetros e interacciones comunes que intervienen en el proceso de generación de la forma, dividido por la complejidad de intercambio de información digital desde el origen hasta la fase de fabricación y construcción”. Una vez analizados los procesos de generación digital de Arquitectura se propone identificar los parámetros geométricos que definen el proceso de Diseño digital, entendiendose por Diseño el proceso que engloba desde la proposición de una forma inicial basada en la intuición del Arquitecto, la generación y evaluación de variantes y posterior definición digital para producción, tanto de un objeto, un sistema o de la totalidad del Proyecto. En la actualidad el proceso de Diseño es discontinuo y lineal organizandose los parámetros por disciplinas en las que está estructurada las atribuciones profesionales en la industria de la construcción. Para simplificar la identificación y listado se han agrupado siguiendo estos grupos de conocimiento. Entendemos parametros invariables aquellos que son independientes de Tipologías arquitectónicas o que dependen del mismo proceso de generación de la Forma. “El listado de los parámetros que intervienen en un proceso de generación formal es una abstracción de una realidad compleja. La parametrización de las decisiones que intervienen en la selección de una forma determinada mediante “well defined problems” es imposible. El proceso que esta tesis describe entiende esta condición como un elemento que pone en valor el propio procedimiento generativo por la riqueza que la subjetividad que el equipo de diseño aporta”. La segunda parte esencial de esta investigación pretende extraer las restricciones propias del estado del arte de la fabricación digital para posteriormente incorporarlos en los procesos digitales de definición de la Forma arquitectónica. “La integración de las restricciones derivadas de las técnicas de fabricación y construcción digitales en el proceso de generación de formas desde el ámbito de la Arquitectura debe referirse a los condicionantes geométricos asociados a cada sistema constructivo, material y técnica de fabricación. La geometría es además el vínculo que permite asociar el conjunto de parámetros prestacionales seleccionados para un Proyecto con los sistemas de fabricación digital”. A estos condicionantes geométricos obtenidos del análisis de cada sistema de fabricación digital se les ha denominado “invariantes geométricos”. Bajo este término se engloban tanto límites dimensionales de fabricación, como materiales compatibles, tolerancias de manufactura e instalación y cualidades prestacionales asociadas. El objetivo de esta propuesta es emplear la geometría, herramienta fundamental y propia del Arquitecto, como nexo de unión entre el conjunto complejo y heterogéneo de parámetros previamente listados y analizados. Para ello se han simplificado en tablas específicas para cada parámetro prestacional los condicionantes geométricos que se derivan de los Sistemas de fabricación digital compatibles (ver apéndice 1). El estudio y evaluación de las capacidades y objetivos de las distintas plataformas de software disponibles y de las experiencias profesionales evaluadas en los proyectos presentados, permiten concluir que la propuesta de plataforma digital de diseño integral multi-paramétrico de formas arquitectónicas requiere de un protocolo de interoperatibilidad específico aún no universalmente establecido. Actualmente el enfoque de la estrategia para normalizar y universalizar el contexto normativo para regular la interoperatibilidad se centra en figura del gestor denominado “BIM manager”. Las atribuciones y roles de esta figura se enfocan a la gestión del continente y no del contenido (Definición de los formatos de intercambio, niveles de desarrollo (LOD) de los componentes o conjuntos constructivos, detección de interferencias y documentación del propio modelo). Siendo este ámbito un desarrollo necesario para la propuesta de universalización del sistema de diseño para fabricación digital integrado, la presente investigación aporta un organigrama y protocolo asociado. El protocolo: 1. Establece la responsabilidad de identificar y definir la Información que debe determinar el proceso de generación y desarrollo de la forma arquitectónica. 2. Define la forma digital apropiada para generar la geometría del Proyecto, incluyendo la precisión necesaria para cada componente y el nivel de detalle necesario para su exportación inequívoca al proceso de fabricación. 3. Define el tempo de cada etapa de diseño identificando un nivel de detalle acorde. 4. Acopla este organigrama dentro de las estructuras nuevas que se proponen en un entorno BIM para asegurar que no se producen solapes o vacíos con las atribuciones que se identifican para el BIM Manager. “El Arquitecto debe dirigir el protocolo de generación coordinada con los sistemas de producción digital para conseguir que la integración completa. El protocolo debe asistir al proceso de generación de forma mediante la evaluación del desempeño prestacional de cada variante en tiempo real. La comunicación entre herramientas digitales es esencial para permitir una ágil transmisión de información. Es necesario establecer un protocolo adaptado a los objetivos y las necesidades operativas de cada proyecto ya que la estandarización de un protocolo único no es posible”. Una decisión estratégica a la hora de planificar una plataforma de diseño digital común es establecer si vamos a optar por un Modelo digital único o diversos Modelos digitales federados. Cada uno de los modos de trabajo tiene fortalezas y debilidades, no obstante en el ámbito de investigación se ha concluido que un proceso integrado de Diseño que incorpore la evaluación prestacional y conceptual definida en el Capítulo 3, requiere necesariamente de varios modelos de software distintos que han de relacionarse entre sí mediante un protocolo de comunicación automatizado. Una plataforma basada en un modelo federado consiste en establecer un protocolo de comunicación entre los programas informáticos empleados por cada disciplina. En este modelo de operación cada equipo de diseño debe establecer las bases de comunicación en función del número y tipo de programas y procesos digitales a emplear. En esta investigación se propone un protocolo basado en los estándares de intercambio de información que estructura cualquier proceso de generación de forma paramétrico “La investigación establece el empleo de algoritmos evolutivos como el sistema actual óptimo para desarrollar un proceso de generación de formas basadas en la integración y coordinación de invariantes geométricos derivados de un conjunto de objetivos prestacionales y constructivos. No obstante, para la aplicación en el caso práctico realizado se ha podido verificar que la evaluación del desempeño aún no puede realizarse en una única herramienta y por lo tanto el proceso de selección de las variantes genéticas óptimas ha de ejecutarse de forma manual y acumulativa. El proceso debe realizarse de manera federada para la selección evolutiva de los invariantes geométricos dimensionales”. La evaluación del protocolo de integración y los condicionantes geométricos obtenidos como parámetros geométricos que controlan las posibles formas compatibles se realiza mediante su aplicación en un caso práctico. El ejercicio simula la colaboración multidisciplinar con modelos federados de plataformas distintas. La elección del tamaño y complejidad constructiva del proyecto se ha modulado para poder alcanzar un desarrollo completo de cada uno de los parámetros prestacionales seleccionados. Continuando con el mismo objetivo propuesto para los parámetros prestacionales, la tipología constructiva-estructural seleccionada para el ejercicio permite la aplicación la totalidad de invariantes geométricos asociados. El objetivo de este caso práctico es evaluar la capacidad alterar la forma inicialmente propuesta mediante la evaluación del desempeño prestacional de conjunto de variantes geométricas generadas a partir de un parámetro dimensional determinado. Para que este proceso tenga sentido, cada una de las variantes debe ser previamente validada conforme a las limitaciones geométricas propias de cada sistema de fabricación y montaje previstos. El interés de las conclusiones obtenidas es la identificación de una variante geométrica distante a la solución simétrica inicialmente como la solución óptima para el conjunto de parámetros seleccionados. Al tiempo se ha comprobado como la participación de un conjunto de parámetros multi-disciplinares que representan la realidad compleja de los objetivos arquitectónicos favorecen la aparición de variaciones genéticas con prestaciones mejoradas a la intuición inicial. “La herencias tipológicas suponen un límite para la imaginación de variantes formales al proceso de ideación arquitectónica. El ejercicio realizado demuestra que incluso en casos donde aparentemente la solución óptima aparenta ser obvia una variante aleatoria puede mejorar su desempeño global. La posibilidad de conocer las condiciones geométricas de las técnicas de fabricación digital compatibles con el conjunto de parámetros seleccionados por el Arquitecto para dirigir el proceso asegura que los resultados del algoritmo evolutivo empleado sean constructivamente viables. La mejora de imaginación humana con la aportación de geometrías realmente construibles supone el objetivo último de esta tesis”. ABSTRACT Architectural form generation process is shifting from analogical to digital. Digital technology has changed the way we design empowering Architects and Engineers to precisely define any complex geometry envisioned. At the same time, the construction industry, following aeronautical and automotive industries, is implementing digital manufacturing techniques to improve efficiency and quality. Consequently construction complexity will no longer be related to geometry complexity and it is associated to coordination with digital manufacturing capacities. Unfortunately it is agreed that non-standard geometries, even when proposed with performance optimization criteria, are only suitable for projects with non-restricted budgets. Furthemore, the lack of coordinated exportation protocol and geometry management between design and construction is avoiding the globalization of emergence process in built projects Present research first objective is to identify exclusive form-generation parameters related to digital manufacturing geometrical restraints. The intention was to use geometry as the form-generation tool and integrate the digital manufacturing capacities at first stages of the project. The first chapter of this text describes the investigation historical context focusing on the influence between accurate geometry definition at non-standard forms and its construction. At first examples of non-Euclidean geometries built the communication between design and construction were based on analogical partial and imprecise documentation. Deficient communication leads to geometry adaptation on site leaving the final form uncontrolled by the Architect. Computer Aided Design enable Architects to define univocally complex geometries that previously where impossible to communicate. “The univocally definition of the Form, and communication between design and construction is essential for complex geometry Projects”. The second chapter is focused on digital technologies application in form finding process and site construction. The case studies selected identifies a clear inflexion node at 1992 with the Guggenheim Museum in Bilbao. The singularity of this project was the use of Aeronautics software to define digitally the external envelope complex geometry to enable the contractor to build it. “The digital revolution has given the Architect the capacity to design buildings beyond the architectural archetypes driven by geometric-constructive limitations. The application of digital manufacturing techniques has enabled a free-form construction without geometrical limitations. In this new context performance shall be the responsible to set new conceptual boundaries, since the behavior of each possible geometry can be compare and analyze beforehand. The role of the Architect is to prioritize the performance and architectural objectives of each project in a complete and coherent set of parameters”. Projects using digital tools for solving various stages of the design process were increased exponentially since 1992 until today. Despite the significant rise of the techniques of computer-aided design the main challenge remains linking geometries and materials proposed at each design with the capabilities of digital manufacturing techniques. Design for manufacturing in a digital environment is a mature technology in other industries such as aerospace and automotive, including consumer products and decoration, but in the construction sector is an immature and disjointed system. The peculiarities of the construction industry have not yet been addressed in its entirety and research proposals made in this area until 2015 have focused in separate parts of the process and not the total process. “The main obstacle to global standardization and implementation of a complete digital process from the form-finding to construction site is the lack of an integrated protocol that integrates manufacturing, economic and commissioning limitations, together with the performance evaluation of each possible form”. The different form generation processes are studied at chapter number 3. At the introduction of this chapter there is a specific definition of "form" for the research field. Form is identified with the outer envelope geometry, including the organizational set of connected indoor spaces connected to it. Therefore it is not exclusive of the interior. The aim of this study is to analyze and classify the main digital form generation processes using different selected projects as emblematic of each type. The approach to this process is complex, with segregated and uncoordinated different actors have to intervene application. In an analogical form-generation process parameters involved are partly conscious and partly unconscious or learned. The architect has control only over limited part of the parameters to be integrated into the design, according to their knowledge and. There is also a learned aesthetical prejudice that leads the form generation process to a specific geometry leaving the performance and optimization criteria apart from the decision making process. “Using performance evaluation digital tools during form finding process provides real-time comparative information to the Architect enabling geometry selection based on its performance. The generative form generation process described at this document does not ambition to identify the optimum geometry for each set of parameters. The objective is to provide quick information at each generation of what direction is most favorable for the performance parameters selected”. Manufacturing complexity definition in relation to a global and integral process of digital design for manufacture is essential for establishing an efficient managing protocol. “The definition of complexity associated to design for production in Architecture is proposed as the factor between number of different agents involved in the process by the number of interactions required between them, divided by the percentage of the interchange of information that is standardized and proof of information loss”. Design in architecture is a multi-objective process by definition. Therefore, addressing generation process linked to a set of non-coherent parameters requires the selection of adequate generative algorithm and the interaction of the architect. During the second half of the twentieth century and early twenty-first century it have been developed various mathematical algorithms for multi-parametric digital design. Heuristic algorithms are the most adequate algorithms for architectural projects due to its nature. The advantage of such algorithms is the ability to efficiently handle large scale optimization cases where a large number of design objectives and variables are involved. These generative processes do not pursue the optimum solution, in fact it will be impossible to proof with such algorithm. This is not a problem in architectural design where the final goal is to guide the form finding process towards a better performance within the initial direction provided by the architect. This research has focused on genetic algorithms due to its capacity to generate geometric alternatives in multiple directions and evaluate the fitness against a set of parameters specified in a single process. "Any protocol seeks to achieve standardization. The design to manufacturing protocol aims to provide a coordinated and coherent form generation process between a set of design parameters and the geometrical requirements of manufacturing technique. The protocol also provides an information exchange environment where there is a communication path and the level of information is ensured. The research is focused on the process because it is considered that each project will have its own singularities and parameters but the process will stay the same. Again the development of a specific tool is not a goal for the research, the intention is to provide an open source protocol that is valid for any set of tools”. Once the digital generation processes are being analized and classified, the next step is to identify the geometric parameters that define the digital design process. The definition of design process is including from the initial shape proposal based on the intuition of the architect to the generation, evaluation, selection and production of alternatives, both of an object , system or of the entire project . The current design process in Architecture is discontinuous and linear, dividing the process in disciplines in which the construction industry is structured. The proposal is to unify all relevant parameters in one process. The parameters are listed in groups of knowledge for internal classification but the matrix used for parameter relationship determination are combined. “A multi-parameter determination of the form-finding process is the integration all the measurable decisions laying behind Architect intuition. It is not possible to formulate and solve with an algorithm the design in Architecture. It is not the intention to do so with the proposal of this research. The process aims to integrate in one open protocol a selection of parameters by using geometry as common language. There is no optimum solution for any step of the process, the outcome is an evaluation of performance of all the form variations to assist the Architect for the selection of the preferable solution for the project”. The research follows with the geometrical restrictions of today Digital manufacturing techniques. Once determined it has been integrated in the form-finding process. “Digital manufacturing techniques are integrated in the form-finding process using geometry as common language. Geometric restraints define the boundary for performance parametric form-finding process. Geometrical limitations are classified by material and constructive system”. Choose between one digital model or several federate models is a strategic decision at planning a digital design for manufacturing protocol. Each one of the working models have strengths and weakens, nevertheless for the research purposes federated models are required to manage the different performance evaluation software platforms. A protocol based on federated models shall establish a communication process between software platforms and consultants. The manager shall integrate each discipline requirements defining the communication basis. The proposed protocol is based on standards on information exchange with singularities of the digital manufacturing industry. “The research concludes evolutionary algorithms as current best system to develop a generative form finding process based on the integration and coordination of a set of performance and constructive objectives. However, for application in professional practice and standardize it, the performance evaluation cannot be done in only one tool and therefore the selection of optimal genetic variants must be run in several iterations with a cumulative result. Consequently, the evaluation process within the geometrical restraints shall be carried out with federated models coordinated following the information exchange protocol”. The integration protocol and geometric constraints evaluation is done by applying in a practical case study. The exercise simulates multidisciplinary collaboration across software platforms with federated models. The choice of size and construction complexity of the project has been modulated to achieve the full development of each of the parameters selected. Continuing with the same objective proposed for the performance parameters the constructive and structural type selected for the exercise allows the application all geometric invariants associated to the set of parameters selected. The main goal of the case study is to proof the capacity of the manufacturing integrated form finding process to generate geometric alternatives to initial form with performance improved and following the restrictions determined by the compatible digital manufacturing technologies. The process is to be divided in consecutive analysis each one limited by the geometrical conditions and integrated in a overall evaluation. The interest of this process is the result of a non-intuitive form that performs better than a double symmetrical form. The second conclusion is that one parameter evaluation alone will not justify the exploration of complex geometry variations, but when there is a set of parameters with multidisciplinary approach then the less obvious solution emerge as the better performing form. “Architectural typologies impose limitation for Architects capacity to imagine formal variations. The case study and the research conclusions proof that even in situations where the intuitive solution apparently is the optimum solution, random variations can perform better when integrating all parameters evaluation. The capacity of foreseing the geometrical properties linking each design parameter with compatible manufacturing technologies ensure the result of the form-finding process to be constructively viable. Finally, the propose of a complete process where the geometry alternatives are generated beyond the Architect intuition and performance evaluated by a set of parameters previously selected and coordinated with the manufacturing requirements is the final objective of the Thesis”.

Characterization cement pastes degraded in lanoratory solutions and physiochemical parameters employed for modeling the process

Previously degradation studies carried out, over a number of different mortars by the research team, have shown that observed degradation does not exclusively depend on the solution equilibrium pH, nor the aggressive anions relative solubility. In our tests no reason was found that could allow us to explain, why same solubility anions with a lower pH are less aggressive than others. The aim of this paper is to study cement pastes behavior in aggressive environments. As observed in previous research, this cement pastes behaviors are not easily explained only taking into account only usual parameters, pH, solubility etc. Consequently the paper is about studying if solution physicochemical characteristics are more important in certain environments than specific pH values. The paper tries to obtain a degradation model, which starting from solution physicochemical parameters allows us to interpret the different behaviors shown by different composition cements. To that end, the rates of degradation of the solid phases were computed for each considered environment. Three cement have been studied: CEM I 42.5R/SR, CEM II/A-V 42.5R and CEM IV/B-(P-V) 32.5 N. The pastes have been exposed to five environments: sodium acetate/acetic acid 0.35 M, sodium sulfate solution 0.17 M, a solution representing natural water, saturated calcium hydroxide solution and laboratory environment. The attack mechanism was meant to be unidirectional, in order to achieve so; all sides of cylinders were sealed except from the attacked surface. The cylinders were taking out of the exposition environments after 2, 4, 7, 14, 30, 58 and 90 days. Both aggressive solution variations in solid phases and in different depths have been characterized. To each age and depth the calcium, magnesium and iron contents have been analyzed. Hydrated phases evolution studied, using thermal analysis, and crystalline compound changes, using X ray diffraction have been also analyzed. Sodium sulphate and water solutions stabilize an outer pH near to 8 in short time, however the stability of the most pH dependent phases is not the same. Although having similar pH and existing the possibility of forming a plaster layer near to the calcium leaching surface, this stability is greater than other sulphate solutions. Stability variations of solids formed by inverse diffusion, determine the rate of degradation.

Polymer-solvent interaction parameters of SBS rubbers by inverse gas chromatography measurements

The solubility parameters of two SBS commercial rubbers with different structures (lineal and radial), and with slightly different styrene content have been determined by inverse gas chromatography technique. The Flory–Huggins interaction parameters of several polymer–solvent mixtures have also been calculated. The influence of the polymer composition, the solvent molecular weight and the temperature over these parameters have been discussed; besides, these parameters have been compared with previous ones, obtained by intrinsic viscosity measurements. From the Flory–Huggins interaction parameters, the infinite dilution activity coefficients of the solvents have been calculated and fitted to the well-known NRTL model. These NRTL binary interaction parameters have a great importance in modelling the separation steps in the process of obtaining the rubber.

Progress on optimization of the solar cell fabrication process by impurity-to-efficiency predictive simulator

To optimize the last high temperature step of a standard solar cell fabrication process (the contact cofiring step), the aluminium gettering is incorporated in the Impurity-to-Efficiency simulation tool, so that it models the phosphorus and aluminium co-gettering effect on iron impurities. The impact of iron on the cell efficiency will depend on the balance between precipitate dissolution and gettering. Gettering efficiency is similar in a wide range of peak temperatures (600-850 ºC), so that this peak temperature can be optimized favoring other parameters (e.g. ohmic contact). An industrial co-firing step can enhance the co-gettering effect by adding a temperature plateau after the peak of temperature. For highly contaminated materials, a short plateau (menor que 2 min) at low temperature (600 ºC) is shown to reduce the dissolved iron.

On track for solar grade silicon through a siemens process-type laboratory reactor: operating conditions and energy savings

Polysilicon cost impacts significantly on the photovoltaics (PV) cost and on the energy payback time. Nowadays, the besetting production process is the so called Siemens process, polysilicon deposition by chemical vapor deposition (CVD) from Trichlorosilane. Polysilicon purification level for PV is to a certain extent less demanding that for microelectronics. At the Instituto de Energía Solar (IES) research on this subject is performed through a Siemens process-type laboratory reactor. Through the laboratory CVD prototype at the IES laboratories, valuable information about the phenomena involved in the polysilicon deposition process and the operating conditions is obtained. Polysilicon deposition by CVD is a complex process due to the big number of parameters involved. A study on the influence of temperature and inlet gas mixture composition on the polysilicon deposition growth rate, based on experimental experience, is shown. Moreover, CVD process accounts for the largest contribution to the energy consumption of the polysilicon production. In addition, radiation phenomenon is the major responsible for low energetic efficiency of the whole process. This work presents a model of radiation heat loss, and the theoretical calculations are confirmed experimentally through a prototype reactor at our disposal, yielding a valuable know-how for energy consumption reduction at industrial Siemens reactors.

Estimating the modal parameters from multiple measurement setups using a joint state space model

Computing the modal parameters of structural systems often requires processing data from multiple non-simultaneously recorded setups of sensors. These setups share some sensors in common, the so-called reference sensors, which are fixed for all measurements, while the other sensors change their position from one setup to the next. One possibility is to process the setups separately resulting in different modal parameter estimates for each setup. Then, the reference sensors are used to merge or glue the different parts of the mode shapes to obtain global mode shapes, while the natural frequencies and damping ratios are usually averaged. In this paper we present a new state space model that processes all setups at once. The result is that the global mode shapes are obtained automatically, and only a value for the natural frequency and damping ratio of each mode is estimated. We also investigate the estimation of this model using maximum likelihood and the Expectation Maximization algorithm, and apply this technique to simulated and measured data corresponding to different structures.

A method to obtain the thermal parameters and the photothermal transduction efficiency in an optical hyperthermia device based on laser irradiation of gold nanoparticles

Optical hyperthermia systems based on the laser irradiation of gold nanorods seem to be a promising tool in the development of therapies against cancer. After a proof of concept in which the authors demonstrated the efficiency of this kind of systems, a modeling process based on an equivalent thermal-electric circuit has been carried out to determine the thermal parameters of the system and an energy balance obtained from the time-dependent heating and cooling temperature curves of the irradiated samples in order to obtain the photothermal transduction efficiency. By knowing this parameter, it is possible to increase the effectiveness of the treatments, thanks to the possibility of predicting the response of the device depending on the working configuration. As an example, the thermal behavior of two different kinds of nanoparticles is compared. The results show that, under identical conditions, the use of PEGylated gold nanorods allows for a more efficient heating compared with bare nanorods, and therefore, it results in a more effective therapy.

One or two poles of attraction in the international technological cooperation process?

In recent years, international cooperation processes have become a key mechanism for companies to internationalise their innovative activities, par ticularly in the case of small businesses whose size reduces their possibilities of developing internationalisation strategies autonomously in the same way as larger companies. In Spain, the existence of two parallel programmes with similar structures oriented towards Europe (EUREKA) and Latin America (IBEROEKA) raises the question as to whether the fact that companies participate in only one (unipolar) or both (bipolar) of these programmes is the result of a selection process, which, in turn, results in the existence of different collectives with different efficiency parameters. The aim of this study is to provide a comparative analysis based on the final reports of Spanish companies that have participated in the EUREKA programme. Two groups of companies were compared: one comprising companies that have only had international experience in Europe (EUREKA); and another formed by companies that have also carried out IBEROEKA projects. The conclusions confirm that the behaviour of both groups of companies differs substantially and reveal the importance of geographical perspective in the analysis of international cooperation in technology. This disparate behaviour is a relevant aspect that must be taken into account when designing policies to promote international technological cooperation.

Tuning of modulation spectrum parameters for voice pathology detection

Acoustic parameters are frequently used to assess the presence of pathologies in human voice. Many of them have demonstrated to be useful but in some cases its results could be optimized by selecting appropriate working margins. In this study two indices, CIL and RALA, obtained from Modulation Spectra are described and tuned using different frame lengths and frequency ranges to maximize AUC in normal to pathological voice detection. After the tuning process, AUC reaches 0.96 and 0.95 values for CIL and RALA respectively representing an improvement of 16 % and 12 % at each case respect to the typical tuning based only on frame length selection.

Understanding and improving the chemical vapor deposition process for solar grade silicon production

Esta Tesis Doctoral se centra en la investigación del proceso de producción de polisilicio para aplicaciones fotovoltaicas (FV) por la vía química; mediante procesos de depósito en fase vapor (CVD). El polisilicio para la industria FV recibe el nombre de silicio de grado solar (SoG Si). Por un lado, el proceso que domina hoy en día la producción de SoG Si está basado en la síntesis, destilación y descomposición de triclorosilano (TCS) en un reactor CVD -denominado reactor Siemens-. El material obtenido mediante este proceso es de muy alta pureza, pero a costa de un elevado consumo energético. Así, para alcanzar los dos principales objetivos de la industria FV basada en silicio, bajos costes de producción y bajo tiempo de retorno de la energía invertida en su fabricación, es esencial disminuir el consumo energético de los reactores Siemens. Por otro lado, una alternativa al proceso Siemens considera la descomposición de monosilano (MS) en un reactor de lecho fluidizado (FBR). Este proceso alternativo tiene un consumo energético mucho menor que el de un reactor Siemens, si bien la calidad del material resultante es también menor; pero ésta puede ser suficiente para la industria FV. A día de hoy los FBR deben aún abordar una serie de retos para que su menor consumo energético sea una ventaja suficiente comparada con otras desventajas de estos reactores. En resumen, la investigación desarrollada se centra en el proceso de depósito de polysilicio por CVD a partir de TCS -reactor Siemens-; pero también se investiga el proceso de producción de SoG Si en los FBR exponiendo las fortalezas y debilidades de esta alternativa. Para poder profundizar en el conocimiento del proceso CVD para la producción de polisilicio es clave el conocimiento de las reacciones químicas fundamentales y cómo éstas influencian la calidad del producto resultante, al mismo tiempo que comprender los fenómenos responsables del consumo energético. Por medio de un reactor Siemens de laboratorio en el que se llevan a cabo un elevado número de experimentos de depósito de polisilicio de forma satisfactoria se adquiere el conocimiento previamente descrito. Se pone de manifiesto la complejidad de los reactores CVD y de los problemas asociados a la pérdidas de calor de estos procesos. Se identifican las contribuciones a las pérdidas de calor de los reactores CVD, éstas pérdidas de calor son debidas principalmente a los fenómenos de radiación y, conducción y convección vía gases. En el caso de los reactores Siemens el fenómeno que contribuye en mayor medida al alto consumo energético son las pérdidas de calor por radiación, mientras que en los FBRs tanto la radiación como el calor transferido por transporte másico contribuyen de forma importante. Se desarrolla un modelo teórico integral para el cálculo de las pérdidas de calor en reactores Siemens. Este modelo está formado a su vez por un modelo para la evaluación de las pérdidas de calor por radiación y modelos para la evaluación de las pérdidas de calor por conducción y convección vía gases. Se ponen de manifiesto una serie de limitaciones del modelo de pérdidas de calor por radiación, y se desarrollan una serie de modificaciones que mejoran el modelo previo. El modelo integral se valida por medio un reactor Siemens de laboratorio, y una vez validado se presenta su extrapolación a la escala industrial. El proceso de conversión de TCS y MS a polisilicio se investiga mediante modelos de fluidodinámica computacional (CFD). Se desarrollan modelados CFD para un reactor Siemens de laboratorio y para un prototipo FBR. Los resultados obtenidos mediante simulación son comparados, en ambos casos, con resultados experimentales. Los modelos desarrollados se convierten en herramientas para la identificación de aquellos parámetros que tienen mayor influencia en los procesos CVD. En el caso del reactor Siemens, ambos modelos -el modelo integral y el modelado CFD permiten el estudio de los parámetros que afectan en mayor medida al elevado consumo energético, y mediante su análisis se sugieren modificaciones para este tipo de reactores que se traducirían en un menor número de kilovatios-hora consumidos por kilogramo de silicio producido. Para el caso del FBR, el modelado CFD permite analizar el efecto de una serie de parámetros sobre la distribución de temperaturas en el lecho fluidizado; y dicha distribución de temperaturas está directamente relacionada con los principales retos de este tipo de reactores. Por último, existen nuevos conceptos de depósito de polisilicio; éstos se aprovechan de la ventaja teórica de un mayor volumen depositado por unidad de tiempo -cuando una mayor superficie de depósito está disponible- con el objetivo de reducir la energía consumida por los reactores Siemens. Estos conceptos se exploran mediante cálculos teóricos y pruebas en el reactor Siemens de laboratorio. ABSTRACT This Doctoral Thesis comprises research on polysilicon production for photovoltaic (PV) applications through the chemical route: chemical vapor deposition (CVD) process. PV polysilicon is named solar grade silicon (SoG Si). On the one hand, the besetting CVD process for SoG Si production is based on the synthesis, distillation, and decomposition of thriclorosilane (TCS) in the so called Siemens reactor; high purity silicon is obtained at the expense of high energy consumption. Thus, lowering the energy consumption of the Siemens process is essential to achieve the two wider objectives for silicon-based PV technology: low production cost and low energy payback time. On the other hand, a valuable variation of this process considers the use of monosilane (MS) in a fluidized bed reactor (FBR); lower output material quality is obtained but it may fulfil the requirements for the PV industry. FBRs demand lower energy consumption than Siemens reactors but further research is necessary to address the actual challenges of these reactors. In short, this work is centered in polysilicon CVD process from TCS -Siemens reactor-; but it also offers insights on the strengths and weaknesses of the FBR for SoG Si production. In order to aid further development in polysilicon CVD is key the understanding of the fundamental reactions and how they influence the product quality, at the same time as to comprehend the phenomena responsible for the energy consumption. Experiments conducted in a laboratory Siemens reactor prove the satisfactory operation of the prototype reactor, and allow to acquire the knowledge that has been described. Complexity of the CVD reactors is stated and the heat loss problem associated with polysilicon CVD is addressed. All contributions to the energy consumption of Siemens reactors and FBRs are put forward; these phenomena are radiation and, conduction and convection via gases heat loss. In a Siemens reactor the major contributor to the energy consumption is radiation heat loss; in case of FBRs radiation and heat transfer due to mass transport are both important contributors. Theoretical models for radiation, conduction and convection heat loss in a Siemens reactor are developed; shaping a comprehensive theoretical model for heat loss in Siemens reactors. Limitations of the radiation heat loss model are put forward, and a novel contribution to the existing model is developed. The comprehensive model for heat loss is validated through a laboratory Siemens reactor, and results are scaled to industrial reactors. The process of conversion of TCS and MS gases to solid polysilicon is investigated by means of computational fluid-dynamics models. CFD models for a laboratory Siemens reactor and a FBR prototype are developed. Simulated results for both CVD prototypes are compared with experimental data. The developed models are used as a tool to investigate the parameters that more strongly influence both processes. For the Siemens reactors, both, the comprehensive theoretical model and the CFD model allow to identify the parameters responsible for the great power consumption, and thus, suggest some modifications that could decrease the ratio kilowatts-hour per kilogram of silicon produced. For the FBR, the CFD model allows to explore the effect of a number of parameters on the thermal distribution of the fluidized bed; that is the main actual challenge of these type of reactors. Finally, there exist new deposition surface concepts that take advantage of higher volume deposited per time unit -when higher deposition area is available- trying to reduce the high energy consumption of the Siemens reactors. These novel concepts are explored by means of theoretical calculations and tests in the laboratory Siemens prototype.