Optimizing the Density of Holes of EWT Solar Cells Taking Into Consideration Mechanical Aspects

EWT solar cells start from drilled wafers with approximately 100 holes/cm2. These holes act as stress concentrators leading to a reduction in the mechanical strength of this type of wafers. The viability of cells with higher density of holes has been studied. To this end, sets of wafers with different density of holes have been characterized. The ring on ring test has been employed and FE models have been developed to simulate the test. The statistical evaluation permits to draw conclusions about the reduction of the strength depending on the density of holes. Moreover, the stress concentration around the holes has been studied by means of the FE method employing the sub-modeling technique. The maximum principal stress of EWT wafers with twice the density of holes of commercial ones is almost the same. However, the mutual interaction between the stress concentration effects around neighboring holes is only observed for wafers with a density of 200 holes/cm2

Elastoplastic consolidation at finite strain. Part 2: finite element implementation and numerical examples

A mathematical model for finite strain elastoplastic consolidation of fully saturated soil media is implemented into a finite element program. The algorithmic treatment of finite strain elastoplasticity for the solid phase is based on multiplicative decomposition and is coupled with the algorithm for fluid flow via the Kirchhoff pore water pressure. A two-field mixed finite element formulation is employed in which the nodal solid displacements and the nodal pore water pressures are coupled via the linear momentum and mass balance equations. The constitutive model for the solid phase is represented by modified Cam—Clay theory formulated in the Kirchhoff principal stress space, and return mapping is carried out in the strain space defined by the invariants of the elastic logarithmic principal stretches. The constitutive model for fluid flow is represented by a generalized Darcy's law formulated with respect to the current configuration. The finite element model is fully amenable to exact linearization. Numerical examples with and without finite deformation effects are presented to demonstrate the impact of geometric nonlinearity on the predicted responses. The paper concludes with an assessment of the performance of the finite element consolidation model with respect to accuracy and numerical stability.

An intelligent portable sensor system in diagnosing stress

Nowadays the stress is a frequent problem in the society. The level of stress could be important in order to recognise health problems later. Electrocardiogram technics allows to supervise the heart condition and the detection of anomalies about the patient. Sometimes the data collection systems by sensors placed on the patient restrict his mobility. Therefore the elimination of wires is a good solution for this trouble. Then the Bluetooth protocol is chosen as way for transmitting and receive data between stations. There are three ECG sensors placed on the right hand, the left hand and the right leg. It is possible to measure the heart signal with this technique. Besides there is an extra sensor in order to measure the temperature of the patient. Depending of the value of these parameters is possible to recognise stress levels. All sensors are connected to a special box with a microcontroller which treat every signal. This module has a Bluetooth part that transmitts wireless the new digital signal to the receiver. This one will be a dongle connected to the computer by Serial Port. A program in the computer has been implemented in order to receive the Bluetooth Data sent from the box and saving the data in a file for subsequent activities. El objetivo principal de este proyecto es el estudio de parámetros como la temperatura corporal y las señales de electrocardiograma para el diagnóstico del estrés. Existen varios estudios que relacionan estos parámetros y sus niveles con posibles casos de estrés y ansiedad. Para este fin usamos unos sensores colocados en el brazo derecho, brazo izquierdo y pierna izquierda. Esto forma el Eindhoven Triangle, que es conocido por dar una señal de electrocardiograma. A su vez también tendremos un sensor de temperatura colocado en un dedo de la mano para medir los grados a los que está el cuerpo en ese momento y así poder detectar ciertas anomalías. Estos sensores están conectados a un modulo que trata las señales analógicas recogidas, las une, y digitaliza para que el modulo transmisor pueda enviar via Bluetooth los datos hacia un receptor colocado en un área cercana. En el módulo hay una electrónica que ayuda a resolver problemas importantes como ruido o interferencias. Este receptor está conectado a un ordenador en el cual he desarrollado una aplicación que implementa el protocolo HCI y cuya funcionalidad es recoger los datos recibidos. Este programa es capaz de crear y gestionar conexiones Bluetooth entre dispositivos. El programa está preparado para que si las conexiones se cortan, se traten en la medida de lo posible los datos recogidos. Los datos se interpretarán y guardarán en un fichero .bin para posteriores usos, como graficaciones y análisis de parámetros. El programa está enteramente hecho en lenguaje Java y tiene un mecanismo de eventos que se activa cada vez que hay datos en el receptor, los recoge y los procesa con el fin de darles un trato posteriormente. Se eligió el formato .bin para los ficheros debido a su pequeño tamaño, ya que aunque sean más laboriosos de usar es mucho más eficiente que un .txt, que en este caso podría ocupar varios megabytes.