Influence of coiling in stress relaxation of prestressing steel wires

The possible deleterious effects of coiling and long-time storage of coiled wires on the stress relaxation behaviour of prestressing steel wires has been checked by means of experimental work and a simple analytical model. The results show that if the requirements of Standards are fulfilled (minimum coiling diameters) these effects can be neglected. However, some other factors like previous residual stresses, long-time storage or storage at high temperatures, can trigger or emphasise this damage to the material. In the authors’ opinion it is recommendable to control the final curvature of the wires after uncoiling prior to prestressing, as required in some Standards.

NDT for concrete under accelerated freeze/thaw tests and surface scaling

Freezing of water or salt solution in concrete pores is a main cause for severe damage and significant reduction of the service life. Most of the freeze-thaw (F-T) accelerated tests measure the scaling of concrete by weighting. This paper presents complementary procedures based on the use of strain gages and ultrasonic pulse velocity (UPV) for measuring the deterioration of concrete due to freezing and thawing. These non-destructive testing (NDT) procedures are applied to two types of concretes, one susceptible to F-T damage and the other does not. The results show a good correlation between scaling and the measurements obtained with NDT. Showing NDT the advantage to detect before the damage and to perform continuous measurement

Bond Modelling of prestressed concrete during the prestressing force release

This paper presents an analytical model for simulating the bond between steel and concrete, in precast prestressed concrete elements, during the prestressing force release. The model establishes a relationship between bond stress, steel and concrete stress and slip in such concrete structures. This relationship allows us to evaluate the bond stress in the transmission zone, where bond stress is not constant, along the whole prestressing force release process. The model is validated with the results of a series of tests and is extended to evaluate the transmission length. This capability has been checked by comparing the transmission length predicted by the model and one measured experimentally in a series of tests.

Toward Multi-Scale Object-Based Data Fusion

This paper proposes a new methodology for object based 2-D data fu- sion, with a multiscale character. This methodology is intended to be use in agriculture, specifically in the characterization of the water status of different crops, so as to have an appropriate water management at a farm-holding scale. As a first approach to its evaluation, vegetation cover vigor data has been integrated with texture data. For this purpose, NDVI maps have been calculated using a multispectral image and Lacunarity maps from the panchromatic image. Preliminary results show this methodology is viable in the integration and management of large volumes of data, which characterize the behavior of agricultural covers at farm-holding scale.

New EBG solutions for mutual coupling reduction

Electromagnetic Band Gap (EBG) based on Frequency Selective Surfaces (FSS) [1] are one type of metamaterials [2] with electrical properties [3]. This EBG are used in mutual coupling reduction, back lobe radiation reduction, etc. In this work not only new shapes for the mushroom-type are presented, but also multilayered configurations were studied in order to reduce the patch size and the necessary number of elements.

Revision of EBG metamaterials and active antennas

This review of Electromagnetic Band Gap (EGB) metamaterials and steering integrated antennas was carried out in IMST GmbH under a short collaboration stay. This activity is in line with Coordinating the Antenna Research in Europe (CARE). The aim is to identify the newest trends, and suggest novel solutions and design methodologies for various applications.

Atmospheric attenuation at 100 and 300 GHz estimated with radiosonde data

The study of atmospheric propagation impairments at submillimeter and THz frequencies is becoming increasingly relevant due to the strong effects caused by the composition of the troposphere and the phenomena occurring in it. The present paper is devoted to the estimation of total attenuation at 100 GHz and 300 GHz under non-rainy scenarios. With this purpose, 4 years of meteorological data from Madrid have been collected, including radiosoundings from Madrid-Barajas Airport and co-site SYNOP observations. This volume of data has been analyzed with the aim of also introducing a detection method of rain conditions, which cannot be easily identified in radiosounding profiles. Finally, the method has been used to discard several probable events which would be responsible of scattering conditions and, hence, yearly CDFs of total attenuation have been obtained. It is expected that the statistics would be closest to the ones obtained by experimental techniques under similar atmospheric conditions.

Study of an electronic steering antenna with a staggered phase shifter configuration

This paper presents a study of three possible solutions that can be taken into account to control the phase shift between elements in an antenna array. Because commercial digital phase shifters have become a strategic element by U.S. Government, these elements have increased their price. For this reason, it is necessary to adopt some solutions that allow us to deal with the design and construction of antenna arrays.

Surface Impedance Characterization for UTD Based Solution with IBC for Surface Fields on a Dielectric-Coated PEC Circular Cylinder

A novel formulation for the surface impedance characterization is introduced for the canonical problem of surface fields on a perfect electric conductor (PEC) circular cylinder with a dielectric coating due to a electric current source using the Uniform Theory of Diffraction (UTD) with an Impedance Boundary Condition (IBC). The approach is based on a TE/TM assumption of the surface fields from the original problem. Where this surface impedance fails, an optimization is performed to minimize the error in the SD Green?s function between the original problem and the equivalent one with the IBC. This new approach requires small changes in the available UTD based solution with IBC to include the geodesic ray angle and length dependence in the surface impedance formulas. This asymptotic method, accurate for large separations between source and observer points, in combination with spectral domain (SD) Green?s functions for multidielectric coatings leads to a new hybrid SD-UTD with IBC to calculate mutual coupling among microstrip patches on a multilayer dielectric-coated PEC circular cylinder. Results are compared with the eigenfunction solution in SD, where a very good agreement is met.

A novel method for radio propagation simulation based on automatic 3D environment reconstruction

In this paper, a novel method to simulate radio propagation is presented. The method consists of two steps: automatic 3D scenario reconstruction and propagation modeling. For 3D reconstruction, a machine learning algorithm is adopted and improved to automatically recognize objects in pictures taken from target region, and 3D models are generated based on the recognized objects. The propagation model employs a ray tracing algorithm to compute signal strength for each point on the constructed 3D map. By comparing with other methods, the work presented in this paper makes contributions on reducing human efforts and cost in constructing 3D scene; moreover, the developed propagation model proves its potential in both accuracy and efficiency.

Moving loads on railway bridges: The Spanish Code approach

This paper presents the results of part of the research carried out by a committee in charge of the elaboration of the new Spanish Code of Actions in Railway Bridges. Following the work developed by the European Rail Research Institute (ERRI), the dynamic effects caused by the Spanish high-speed train TALGO have been studied and compared with other European trains. A simplified envelope of the impact coefficient is also presented. Finally, the train-bridge interactions has been analysed and the results compared with those obtained from simple models based on moving loads.

Self-similar deflagration in laser half-plasmas

The self-similar motion of a half-space plasma, generated by a linear pulse of laser radiation absorbed anomalously at the critical density, has been studied. The resulting plasma structure has been completely determined for [pulse duration (critical density)maximum irradiation] large enough

High Intensity Lasers Application to Advanced Materials Processing: Laser Peening and Related Processes

High Intensity Lasers Application to Advanced Materials Processing: Laser Peening and Related

Experimental validation of a fracture model for pearlitic steel bars based on the cohesive zone model

Congreso internacional celebrado en Praga sobre modelos numéricos de fractura en el campo de la ciencia de materiales y estructuras.