Trace Elements Distribution in Red Soils under Semiarid Mediterranean Environment

This study states the potential trace elements (TE’s) content of red soils located at the centre region of Spain, characterized by low rainfall and slight acidity over prolonged weathering periods. For this purpose, three soil profiles from a catena were described, sampled and analyzed. The most notable characteristics are the low organic matter content and the predominantly acidic pH. Illite and kaolinite are the predominant clay minerals. The fertility of the soils is sufficient to provide most of the nutrients required, with very suitable potassium levels. The geochemical characters of this soil are: only few elements remain almost invariable across the profiles and over time, however the majority of them were directly linked with the clay content. These soils are characterized by relatively low levels of some trace elements such as Sr (64.35 mg?kg–1), Ba (303.67 mg?kg–1) and Sc (13.14 mg?kg–1); high levels of other trace elements such as V (103.92 mg?kg–1), Cr (79.9 mg?kg–1), Cu (15.18 mg?kg–1), Hf (10.26 mg?kg–1), Ni (38 mg?kg–1) and Zr (337 mg?kg–1); while the levels for rare earth elements (REE’s) such as La (48.36 mg?kg–1), Ce (95.07 mg?kg–1), Th (13.33 mg?kg–1) and Nd (42.65 mg?kg–1) are significantly high. The distribution of mayor and trace elements was directly re- lated to weathering processes, parent material and anthropogenic activities.

Vacíos urbanos en la ciudad de Zaragoza (1975-2010). Oportunidades para la estructuración y continuidad urbana

La expansión de las ciudades hacia la periferia en las últimas décadas ha generado una serie de tejidos en colisión, donde los intersticios y los espacios residuales muestran la realidad de una ciudad dispersa. A esta serie de espacios intermedios los denominaremos “vacíos urbanos” y determinaremos una serie de factores que hagan posible su identificación Los vacíos urbanos son el objeto de la Tesis. El concepto “vacío urbano” adquiere un determinado significado para la investigación y se acota formulando una serie de parámetros para su definición. Definiremos los “vacíos urbanos” como espacios que han aparecido en el extrarradio de las ciudades, fruto de una expansión sin precedentes de las áreas urbanas. Han surgido como lugares residuales condicionados por elementos naturales o por infraestructuras, ligados a una temporalidad incierta, no inmersos en la dinámicas urbanas o habiendo perdido su funcionalidad. El objetivo de esta investigación es localizar y clasificar los vacíos existentes en la ciudad partiendo de la hipótesis de que es posible establecer una metodología para su reconocimiento y comprobación de los parámetros que los definen. La investigación centra su estudio en la ciudad de Zaragoza, como un ejemplo paradigmático, confirmando que la nueva fenomenología territorial, no sólo se manifiesta en dicha ciudad y en las áreas en concreto donde se ha estudiado, sino que más bien se trata de observarla como una serie de modelos tipológicos que respondan a un proceso de análisis. La propuesta metodológica de loa tesis pasa por reconocerlos, mostrarlos y darles una visibilidad que permita su clasificación, el desarrollo de un estudio de Áreas de la ciudad donde se localizan y un análisis de cada tipología de vacío urbano. Como instrumento metodológico se ha elaborado una detallada cartografía a diferentes escalas. La realización de los planos ha sido el medio de análisis que ha permitido localizar e interpretar los vacíos, complementado con unas escogidas fotografías de estos entornos. La metodología se convierte en un modo de descubrir y analizar los vacíos, el proceso conlleva la comprobación y la clasificación en una tipología. Según se han ido analizando nuevas áreas, se confirma como un hecho repetitivo exitoso y se observa que es aplicable a otras áreas urbanas de similares características, donde se den las condiciones principales de cada tipo. En general, deberán ser espacios localizados en la periferia de núcleos urbanos donde aparezcan fenómenos ligados a una expansión discontinua. Parece probable que el futuro de la ciudad se tenga que resolver en las próximas décadas sobre su actual extensión; bajo este supuesto, es trascendente la función que los vacíos puedan desempeñar en el futuro desarrollo urbano. Toda posibilidad de intervención precisará de una necesaria reinterpretación, puestas las miras en su potencial como elementos capaces de generar una rehabilitación urbana. A su vez se hace conveniente plantear una reflexión sobre estos espacios cargados de una dimensión social y cultural, como lugares capaces de articular y dotar de identidad al medio urbano. Los vacíos deberían protagonizar un papel relevante en la estructuración urbana, abriendo posibilidades para el tramado de la ciudad desde nuevas perspectivas. Una apuesta para que estos espacios libres pasen de ser el objetivo de procesos urbanizadores tradicionales, a ser considerados como oportunos elementos vertebradores de los entornos periurbanos, colaborando en el objetivo de una ciudad contemporánea sostenible. ABSTRACT In the last decades the city periphary expansion has provoked a series of matters to collide, where interstices and waste lands show the reality of a divided city. We shall determine a number of factors allowing us to treat these “in between” spaces, also called "urban voids" as identifiable elements. We will consider them the subject of the thesis and establish them as a "concept", delimiting the meaning of the research specifically acquired, defining, and formulating a set of parameters. "Urban voids" are defined as spaces that have appeared on the outskirts of cities, the result of an unprecedented expansion of urban areas. They have emerged as waste lands, conditioned by natural elements or infrastructure, related to uncertain temporality, not immersed in the urban dynamics, or having lost their functionality. It seems likely that in the upcoming decades, the future of the city will have to resolve its current way of expanding . It is under this assumption that urban voids, as intermediate spaces, will play an important role in future urban developments. Any possible intervention will require a necessary reinterpretation, closely watching their potential as elements capable of generating an urban rehabilitation. At the same time, we wish to reflect on these spaces, in many cases loaded with a social and cultural dimension, as places able to articulate and give identity to the urban environment. Based on the hypothesis that it is possible to establish a methodology for recognition and verification, the purpose of this research is to locate and classify the existing urban voids in the city. The research focuses its study on the city of Saragossa which can be seen as a paradigmatic example. The objective is to confirm that this new territorial phenomenology, not only manifests itself in Saragossa and specific areas under study, but also, can be observed as a series of typological models that respond to a review process. The methodological proposal will recognize, demonstrate, and exhibit these urban voids, in a light that will allow us to classify them, examine the different areas where they can be found, and develop a tipology analysis of each type of urban void found. The technical tool used in this research is a detailed mapping at different scales. A realization of plans, as a mean of analysis, supplemented with a few selected pictures of these environments, will facilitate the location and interpretation of these voids. This scholarly approach to discover and analyze urban voids will involve checking and classifying them in a typology. It has been confirmed as a successful constant regulator while exploring new areas. It will be apply to other urban areas with similar characteristics, that is, spaces located on the periphery of urban areas where expansion is linked to the appearence of discontinuous phenomena. The urban voids play a fundamental role within the urban structure, providing the city a weaving scheme with opportunities of fresh perspectives. The challenge for these free spaces is to move from being the consequence of traditional urban development processes, to being considered opportune backbone elements of peri-urban environments, and to finally contribute to the objectives of a sustainable contemporary city.

Boundary elements in potential and elasticity theory

A general theory that describes the B.I.E. linear approximation in potential and elasticity problems, is developed. A method to tread the Dirichlet condition in sharp vertex is presented. Though the study is developed for linear elements, its extension to higher order interpolation is straightforward. A new direct assembling procedure of the global of equations to be solved, is finally showed.

P-adaptive boundary elements for three-dimensional potential problems

This paper deals with the boundary element method (BEM) p-convergence approach applied to three-dimensional problems governed by Laplace's equation. The advantages derived from the boundary discretization and hierarchical interpolation functions are collated in order to minimize human effort in preparation of input data and improve numerical results.

Energy saving potential of semi-transparent photovoltaic elements for building integration

Within the building energy saving strategies, BIPV (building integrated photovoltaic systems) present a promising potential based on the close relationship existing between these multifunctional systems and the overall building energy balance. Building integration of STPV (semi-transparent photovoltaic) elements affects deeply the building energy demand since it influences the heating, cooling and lighting loads as well as the local electricity generation. This work analyses over different window-to-wall ratios the overall energy performance of five STPV elements, each element having a specific degree of transparency, in order to assess the energy saving potential compared to a conventional solar control glass compliant with the local technical standard. The prior optical characterization, focused to measure the spectral properties of the elements, was experimentally undertaken. The obtained data were used to perform simulations based on a reference office building using a package of specific software tools (DesignBuilder, EnergyPlus, PVsyst, and COMFEN) to take proper account of the STPV peculiarities. To evaluate the global energy performance of the STPV elements a new Energy Balance Index was formulated. The results show that for intermediate and large façade openings the energy saving potential provided by the STPV solutions ranges between 18% and 59% compared to the reference glass.

Dynamic analysis using finite elements to calculate the critical wear section of the contact wire in suburban railway overhead conductor rails

The purpose of this study is to determine the critical wear levels of the contact wire of the catenary on metropolitan lines. The study has focussed on the zones of contact wire where localised wear is produced, normally associated with the appearance of electric arcs. To this end, a finite element model has been developed to study the dynamics of pantograph-catenary interaction. The model includes a zone of localised wear and a singularity in the contact wire in order to simulate the worst case scenario from the point of view of stresses. In order to consider the different stages in the wire wear process, different depths and widths of the localised wear zone were defined. The results of the dynamic simulations performed for each stage of wear let the area of the minimum resistant section of the contact wire be determined for which stresses are greater than the allowable stress. The maximum tensile stress reached in the contact wire shows a clear sensitivity to the size of the local wear zone, defined by its width and depth. In this way, if the wear measurements taken with an overhead line recording vehicle are analysed, it will be possible to calculate the potential breakage risk of the wire. A strong dependence of the tensile forces of the contact wire has also been observed. These results will allow priorities to be set for replacing the most critical sections of wire, thereby making maintenance much more efficient. The results obtained show that the wire replacement criteria currently borne in mind have turned out to be appropriate, although in some wear scenarios these criteria could be adjusted even more, and so prolong the life cycle of the contact wire.

A review of the distribution of particulate trace elements in urban terrestrial environments and its application to considerations of risk

We review the evolution, state of the art and future lines of research on the sources, transport pathways, and sinks of particulate trace elements in urban terrestrial environments to include the atmosphere, soils, and street and indoor dusts. Such studies reveal reductions in the emissions of some elements of historical concern such as Pb, with interest consequently focusing on other toxic trace elements such as As, Cd, Hg, Zn, and Cu. While establishment of levels of these elements is important in assessing the potential impacts of human society on the urban environment, it is also necessary to apply this knowledge in conjunction with information on the toxicity of those trace elements and the degree of exposure of human receptors to an assessment of whether such contamination represents a real risk to the city’s inhabitants and therefore how this risk can be addressed.

P-Adaptive Boundary Elements

This paper presents the implementation of an adaptive philosophy to plane potential problems, using the direct boundary element method. After some considerations about the state of the art and a discussion of the standard approach features, the possibility of separately treating the modelling of variables and their interpolation through hierarchical shape functions is analysed. Then the proposed indicators and estimators are given, followed by a description of a small computer program written for an IBM PC. Finally, some examples show the kind of results to be expected.

Implementation of Boundary Elements in Microcomputers

In this chapter we are going to develop some aspects of the implementation of the boundary element method (BEM)in microcomputers. At the moment the BEM is established as a powerful tool for problem-solving and several codes have been developed and maintained on an industrial basis for large computers. It is also well known that one of the more attractive features of the BEM is the reduction of the discretization to the boundary of the domain under study. As drawbacks, we found the non-bandedness of the final matrix, wich is a full asymmetric one, and the computational difficulties related to obtaining the integrals which appear in the influence coefficients. Te reduction in dimensionality is crucial from the point of view of microcomputers, and we believe that it can be used to obtain competitive results against other domain methods. We shall discuss two applications in this chapter. The first one is related to plane linear elastostatic situations, and the second refers to plane potential problems. In the first case we shall present the classical isoparametric BEM approach, using linear elements to represent both the geometry and the variables. The second case shows how to implement a p-adaptive procedure using the BEM. This latter case has not been studied until recently, and we think that the future of the BEM will be related to its development and to the judicious exploitation of the graphics capabilities of modern micros. Some examples will be included to demonstrate the kind of results that can be expected and sections of printouts will show useful details of implementation. In order to broaden their applicability, these printouts have been prepared in Basic, although no doubt other languages may be more appropiate for effective implementation.

Indicators and Estimators in P-Adaptive Boundary Elements

The paper presents the possibility of implementing a p-adaptive process with the B.E.M. Although the exemples show that good results can be obtained with a limited amount of storage and with the simple ideas explained above, more research is needed in order to improve the two main problems of the method, i.e.: the criteria of where to refine and until what degree. Mathematically based reasoning is still lacking and will be useful to simplify the decission making. Nevertheless the method seems promising and, we hope, opens a path for a series of research lines of maximum interest. Although the paper has dealt only with plane potential problem the extension to plane elasticity as well as to 3-D potential problem is straight-forward.

Hierarchical boundary elements

In this paper we show the possibility of applying adaptive procedures as an alternative to the well-known philosophy of standard Boundary Elements. The three characteristic steps of adaptive procedures, i.e. hierarchical shape functions families, indicator criteria, and a posteriori estimation, can be defined in order to govern an automatic refinement and stopping of the solution process. A computer program to treat potential problems, called QUEIMADA, has been developed to show the capabilities of the new idea.

Improved boundary elements in torsion problems

Since the epoch-making "memoir" of Saint-Venant in 1855 the torsion of prismatic and cilindrical bars has reduced to a mathematical problem: the calculation of an analytical function satisfying prescribed boundary values. For over one century, till the first applications of the F.E.M. to the problem, the only possibility of study in irregularly shaped domains was the beatiful, but limitated, theory of complex function analysis, several functional approaches and the finite difference method. Nevertheless in 1963 Jaswon published an interestingpaper which was nearly lost between the splendid F. E.M. boom. The method was extended by Rizzo to more complicated problems and definitively incorporated to the scientific community background through several lecture-notes of Cruse recently published, but widely circulated during past years. The work of several researches has shown the tremendous possibilities of the method which is today a recognized alternative to the well established F .E. procedure. In fact, the first comprehensive attempt to cover the method, has been recently published in textbook form. This paper is a contribution to the implementation of a difficulty which arises if the isoparametric elements concept is applicated to plane potential problems with sharp corners in the boundary domain. In previous works, these problems was avoided using two principal approximations: equating the fluxes round the corner or establishing a binode element (in fact, truncating the corner). The first approximation distortes heavily the solution in thecorner neighbourhood, and a great amount of element is neccesary to reduce its influence. The second is better suited but the price payed is increasing the size of the system of equations to be solved. In this paper an alternative formulation, consistent with the shape function chosen in the isoparametric representation, is presented. For ease of comprehension the formulation has been limited to the linear element. Nevertheless its extension to more refined elements is straight forward. Also a direct procedure for the assembling of the equations is presented in an attempt to reduce the in-core computer requirements.

Mixed Elements in the Boundary Theory

The development of (static and dynamics)programs with constant and linear elements has shown good behaviour. It seems so natural to combine both advantages so that the results will not be affected by local distortions. This paper will be dedicated to presenting the reserch of mixed elements and the way to solve the over-determination that appears in some cases. Although all the study has been done with the potential theory, its application to elastic problems is straightforward.

Optical bistable devices as sensing elements

The nonlinear optical properties of many materials and devices have been the main object of research as potential candidates for sensing in different places. Just one of these properties has been, in most of the cases, the basis for the sensing operation. As a consequence, just one parameter can be detected. In this paper, although just one property will be employed too, we will show the possibility to sense different parameters with just one type of sensor. The way adopted in this work is the use of the optical bistability obtained from different photonic structures. Because this optical bistability has a strong dependence on many different parameters the possibility to sense different inputs appears. In our case, we will report the use of some non-linear optical devices, mainly Semiconductor Optical Amplifiers, as sensing elements. Because their outputs depend on many parameters, as the incident light wavelength, polarization, intensity and direction, applied voltage and feedback characteristics, they can be employed to detect, at the same time, different type of signals. This is because the way these different signals affect to the sensor response is very different too and appears under a different set of characteristics.

Potential theory

In this chapter we will introduce the reader to the techniques of the Boundary Element Method applied to simple Laplacian problems. Most classical applications refer to electrostatic and magnetic fields, but the Laplacian operator also governs problems such as Saint-Venant torsion, irrotational flow, fluid flow through porous media and the added fluid mass in fluidstructure interaction problems. This short list, to which it would be possible to add many other physical problems governed by the same equation, is an indication of the importance of the numerical treatment of the Laplacian operator. Potential theory has pioneered the use of BEM since the papers of Jaswon and Hess. An interesting introduction to the topic is given by Cruse. In the last five years a renaissance of integral methods has been detected. This can be followed in the books by Jaswon and Symm and by Brebbia or Brebbia and Walker.In this chapter we shall maintain an elementary level and follow a classical scheme in order to make the content accessible to the reader who has just started to study the technique. The whole emphasis has been put on the socalled "direct" method because it is the one which appears to offer more advantages. In this section we recall the classical concepts of potential theory and establish the basic equations of the method. Later on we discuss the discretization philosophy, the implementation of different kinds of elements and the advantages of substructuring which is unavoidable when dealing with heterogeneous materials.