Efectos dinámicos debidos al tráfico de ferrocarril sobre la infraestructura de vía y las estructuras

La vía tradicional sobre balasto sigue siendo una selección para las líneas de alta velocidad a pesar de los problemas técnicos y la prestación del funcionamiento. El problema de la vía sobre balasto es el proceso continuo del deterioro de éste debido a las cargas asociadas al tráfico ferroviario. En consecuencia es imprescindible un mantenimiento continuado para mantener un alineamiento adecuado de la vía. Por eso se surge la necesidad de comprender mejor el mecanismo involucrado en el deterioro de la vía y los factores claves que rigen su progresión a lo largo de ciclos de carga con el fin de reducir los costos del mantenimiento de la vía y mejorar el diseño de las nuevas vías. La presente tesis intenta por un lado desarrollar los modelos más adecuados y eficientes del vehículo y de la vía para los cálculos de los efectos dinámicos debido al tráfico de ferrocarril sobre la infraestructura de la vía sobre balasto, y por otro evaluar estos efectos dinámicos sobre el deterioro de la vía sobre balasto a largo plazo, empleando un adecuado modelo de predicción del deterioro de la misma. Se incluye en el trabajo una recopilación del estado del arte en lo referente a la dinámica de la vía, a la modelización del vehículo, de la vía y de la interacción entre ambos. También se hace un repaso al deterioro de la vía y los factores que influyen en su proceso. Para la primera línea de investigación de esta tesis, se han desarrollado los diferentes modelos del vehículo y de la vía y la modelización de la interacción entre ambos para los cálculos dinámicos en dos y tres dimensiones. En la interacción vehículo-vía, se ha empleado la formulación de contacto nodo-superficie para establecer la identificación de las superficies en contacto y el método de los multiplicadores de Lagrange para imponer las restricciones de contacto. El modelo de interacción se ha contrastado con los casos reportados en la literatura. Teniendo en cuenta el contacto no lineal entre rueda-carril y los perfiles de irregularidades distribuidas de la vía, se han evaluado y comparado los efectos dinámicos sobre el sistema vehículo-vía en la interacción de ambos, para distintas velocidades de circulación del vehículo, en los aspectos como la vibración del vehículo, fuerza de contacto, fuerza transmitida en los railpads, la vibración del carril. También se hace un estudio de la influencia de las propiedades de los componentes de la vía en la respuesta dinámica del sistema vehículo-vía. Se ha desarrollado el modelo del asiento de la vía que consiste en la implementación del modelo de acumulación de Bochum y del modelo de hipoplasticidad en la subrutina del usuario \UMAT" del programa ABAQUS. La implementación numérica ha sido comprobado al comparar los resultados de las simulaciones numéricas con los reportados en la literatura. Se ha evaluado la calidad geométrica de la vía sobre balasto de los tramos de estudio con datos reales de la auscultación proporcionados por ADIF (2012). Se ha propuesto una metodología de simulación, empleando el modelo de asiento, para reproducir el deterioro de la geometría de la vía. Se usan los perfiles de la nivelación longitudinal de la auscultación como perfiles de irregularidades iniciales de la vía en las simulaciones numéricas. También se evalúa la influencia de la velocidad de circulación sobre el deterioro de la vía. The traditional ballast track structures are still being used in high speed railways lines with success, however technical problems or performance features have led to ballast track solution in some cases. The considerable maintenance work is needed for ballasted tracks due to the track deterioration. Therefore it is very important to understand the mechanism of track deterioration and to predict the track settlement or track irregularity growth rate in order to reduce track maintenance costs and enable new track structures to be designed. This thesis attempts to develop the most adequate and efficient models for calculation of dynamic track load effects on railways track infrastructure, and to evaluate these dynamic effects on the track settlement, using a track settlement prediction model, which consists of the vehicle/track dynamic model previously selected and a track settlement law. A revision of the state of the knowledge regarding the track dynamics, the modelling of the vehicle, the track and the interaction between them is included. An overview related to the track deterioration and the factors influencing the track settlement is also done. For the first research of this thesis, the different models of vehicle, track and the modelling of the interaction between both have been developed. In the vehicle-track interaction, the node-surface contact formulation to establish the identification of the surfaces in contact and the Lagrange multipliers method to enforce contact constraint are used. The interaction model has been verified by contrast with some benchmarks reported in the literature. Considering the nonlinear contact between wheel-rail and the track irregularities, the dynamic effects on the vehicle-track system have been evaluated and compared, for different speeds of the vehicle, in aspects as vehicle vibration, contact force, force transmitted in railpads, rail vibration. A study of the influence of the properties of the track components on the the dynamic response of the vehicle-track system has been done. The track settlement model is developed that consist of the Bochum accumulation model and the hipoplasticity model in the user subroutine \UMAT" of the program ABAQUS. The numerical implementation has been verified by comparing the numerical results with those reported in the literature. The geometric quality of the ballast track has been evaluated with real data of auscultation provided by ADIF (2012). The simulation methodology has been proposed, using the settlement model for the ballast material, to reproduce the deterioration of the track geometry. The profiles of the longitudinal level of the auscultation is used as initial profiles of the track irregularities in the numerical simulation. The influence of the running speed on the track deterioration is also investigated.

Sampling strategies using the "accumulation chamber" for monitoring geological

Fundación Ciudad de la Energía (CIUDEN) is carrying out a project of geological storage of CO2, where CO2 injection tests are planned in saline aquifers at a depth of 1500 m for scientific objectives and project demonstration. Before any CO2 is stored, it is necessary to determine the baseline flux of CO2 in order to detect potential leakage during injection and post-injection monitoring. In November 2009 diffuse flux measurements of CO2 using an accumulationchamber were made in the area selected by CIUDEN for geological storage, located in Hontomin province of Burgos (Spain). This paper presents the tests carried out in order to establish the optimum sampling methodology and the geostatistical analyses performed to determine the range, with which future field campaigns will be planned.

Coupled model of initiation and propagation of corrosion in reinforced concrete

Corrosion of reinforcing steel in concrete due to chloride ingress is one of the main causes of the deterioration of reinforced concrete structures. Structures most affected by such a corrosion are marine zone buildings and structures exposed to de-icing salts like highways and bridges. Such process is accompanied by an increase in volume of the corrosión products on the rebarsconcrete interface. Depending on the level of oxidation, iron can expand as much as six times its original volume. This increase in volume exerts tensile stresses in the surrounding concrete which result in cracking and spalling of the concrete cover if the concrete tensile strength is exceeded. The mechanism by which steel embedded in concrete corrodes in presence of chloride is the local breakdown of the passive layer formed in the highly alkaline condition of the concrete. It is assumed that corrosion initiates when a critical chloride content reaches the rebar surface. The mathematical formulation idealized the corrosion sequence as a two-stage process: an initiation stage, during which chloride ions penetrate to the reinforcing steel surface and depassivate it, and a propagation stage, in which active corrosion takes place until cracking of the concrete cover has occurred. The aim of this research is to develop computer tools to evaluate the duration of the service life of reinforced concrete structures, considering both the initiation and propagation periods. Such tools must offer a friendly interface to facilitate its use by the researchers even though their background is not in numerical simulation. For the evaluation of the initiation period different tools have been developed: Program TavProbabilidade: provides means to carry out a probability analysis of a chloride ingress model. Such a tool is necessary due to the lack of data and general uncertainties associated with the phenomenon of the chloride diffusion. It differs from the deterministic approach because it computes not just a chloride profile at a certain age, but a range of chloride profiles for each probability or occurrence. Program TavProbabilidade_Fiabilidade: carries out reliability analyses of the initiation period. It takes into account the critical value of the chloride concentration on the steel that causes breakdown of the passive layer and the beginning of the propagation stage. It differs from the deterministic analysis in that it does not predict if the corrosion is going to begin or not, but to quantifies the probability of corrosion initiation. Program TavDif_1D: was created to do a one dimension deterministic analysis of the chloride diffusion process by the finite element method (FEM) which numerically solves Fick’second Law. Despite of the different FEM solver already developed in one dimension, the decision to create a new code (TavDif_1D) was taken because of the need to have a solver with friendly interface for pre- and post-process according to the need of IETCC. An innovative tool was also developed with a systematic method devised to compare the ability of the different 1D models to predict the actual evolution of chloride ingress based on experimental measurements, and also to quantify the degree of agreement of the models with each others. For the evaluation of the entire service life of the structure: a computer program has been developed using finite elements method to do the coupling of both service life periods: initiation and propagation. The program for 2D (TavDif_2D) allows the complementary use of two external programs in a unique friendly interface: • GMSH - an finite element mesh generator and post-processing viewer • OOFEM – a finite element solver. This program (TavDif_2D) is responsible to decide in each time step when and where to start applying the boundary conditions of fracture mechanics module in function of the amount of chloride concentration and corrosion parameters (Icorr, etc). This program is also responsible to verify the presence and the degree of fracture in each element to send the Information of diffusion coefficient variation with the crack width. • GMSH - an finite element mesh generator and post-processing viewer • OOFEM – a finite element solver. The advantages of the FEM with the interface provided by the tool are: • the flexibility to input the data such as material property and boundary conditions as time dependent function. • the flexibility to predict the chloride concentration profile for different geometries. • the possibility to couple chloride diffusion (initiation stage) with chemical and mechanical behavior (propagation stage). The OOFEM code had to be modified to accept temperature, humidity and the time dependent values for the material properties, which is necessary to adequately describe the environmental variations. A 3-D simulation has been performed to simulate the behavior of the beam on both, action of the external load and the internal load caused by the corrosion products, using elements of imbedded fracture in order to plot the curve of the deflection of the central region of the beam versus the external load to compare with the experimental data.

The role of cover crops in irrigated systems: water balance, nitrate leaching and soil mineral nitrogen accumulation

Soil salinity and salt leaching are a risk for sustainable agricultural production in many irrigated areas. This study was conducted over 3.5 years to determine how replacing the usual winter fallow with a cover crop (CC) affects soil salt accumulation and salt leaching in irrigated systems. Treatments studied during the period between summer crops were: barley (Hordeum vulgare L.), vetch (Vicia villosa L.) and fallow. Soil water content was monitored daily to a depth of 1.3 m and used with the numerical model WAVE to calculate drainage. Electrical conductivity (EC) was measured in soil solutions periodically, and in the soil saturated paste extracts before sowing CC and maize. Salt leaching was calculated multiplying drainage by total dissolved salts in the soil solution, and use to obtain a salt balance. Total salt leaching over the four winter fallow periods was 26 Mg ha−1, whereas less than 18 Mg ha−1 in the presence of a CC. Periods of salt gain occurred more often in the CC than in the fallow. By the end of the experiment, net salt losses occurred in all treatments, owing to occasional periods of heavy rainfall. The CC were more prone than the fallow to reduce soil salt accumulation during the early growth stages of the subsequent cash crop.

Distribution of indole-3-acetic acid in Petunia hybrida shoot tip cuttings and relationship between auxin transport, carbohydrate metabolism and adventitious root formation.

To determine the contribution of polar auxin transport (PAT) to auxin accumulation and to adventitious root (AR) formation in the stem base of Petunia hybrida shoot tip cuttings, the level of indole-3-acetic acid (IAA) was monitored in non-treated cuttings and cuttings treated with the auxin transport blocker naphthylphthalamic acid (NPA) and was complemented with precise anatomical studies. The temporal course of carbohydrates, amino acids and activities of controlling enzymes was also investigated. Analysis of initial spatial IAA distribution in the cuttings revealed that approximately 40 and 10% of the total IAA pool was present in the leaves and the stem base as rooting zone, respectively. A negative correlation existed between leaf size and IAA concentration. After excision of cuttings, IAA showed an early increase in the stem base with two peaks at 2 and 24h post excision and, thereafter, a decline to low levels. This was mirrored by the expression pattern of the auxin-responsive GH3 gene. NPA treatment completely suppressed the 24-h peak of IAA and severely inhibited root formation. It also reduced activities of cell wall and vacuolar invertases in the early phase of AR formation and inhibited the rise of activities of glucose-6-phosphate dehydrogenase and phosphofructokinase during later stages. We propose a model in which spontaneous AR formation in Petunia cuttings is dependent on PAT and on the resulting 24-h peak of IAA in the rooting zone, where it induces early cellular events and also stimulates sink establishment. Subsequent root development stimulates glycolysis and the pentosephosphate pathway

Wearable soft robotic device for post-stroke shoulder rehabilitation: identifying misalignments

Stroke is the leading cause of long-term disability in the United States, affecting over 795,000 people annually. In order to regain motor function of the upper body, patients are usually treated by regular sessions with a dedicated physical therapist. A cost-effective wearable upper body orthotics system that can be used at home to empower both the patients and physical therapists is described. The system is composed of a thin, compliant, lightweight, cost-effective soft orthotic device with an integrated cable actuation system that is worn over the upper body, an embedded limb position sensing system, an electric actuator package and controller. The proposed device is robust to misalignments that may occur during actuation of the compliant brace or when putting on the system. Through simulations and experimental evaluation, it was demonstrated i) that the soft orthotic cable-driven shoulder brace can be successfully actuated without the production of off-axis torques in the presence of misalignments and ii) that the proposed model can identify linear and angular misalignments online.

Computational model for local damage assesment of structures

In the last years many studies have been developed to analyze the seismic behavior throug the damage concept. In fact, the evaluation of the structural damage is important in order to quantify the safety of new and existing structures and, also, to establish a framework for seismic retrofitting decision making of structures. Most proposed models are based on a post-earthquake evaluation in such a way they uncouple the computation of the structural response from that of damage. However, there are other models which include explicity the existing coupling between the degradation and the structural mechanical beaviour. Those models are closer to the physical reality and its formulation is based on the principles of Continuum Damage Mechanics. In the present work, a coupled model is formulated using a simplified application of the Continuum Damage Mechanics to the analysis of frames and allows its representation in standard finite element programs. This work is part of the activities developed by the Structural Mechanics Department (UPM) within ICONS (European Research Project on Innovative Seismic Design Concepts for New and Existing Structures).

Sampling strategies using the "accumulation chamber" for monitoring geological storage of CO2

Fundación Ciudad de la Energía (CIUDEN) is carrying out a project of geological storage of CO2, where CO2 injection tests are planned in saline aquifers at a depth of 1500 m for scientific objectives and project demonstration. Before any CO2 is stored, it is necessary to determine the baseline flux of CO2 in order to detect potential leakage during injection and post-injection monitoring. In November 2009 diffuse flux measurements of CO2 using an accumulation chamber were made in the area selected by CIUDEN for geological storage, located in Hontomin province of Burgos (Spain). This paper presents the tests carried out in order to establish the optimum sampling methodology and the geostatistical analyses performed to determine the range, with which future field campaigns will be planned.

Electrical model for characterizing CVD graphene

Due to its extremely small thickness (0.35 nm), graphene is an intrinsic 2D nanomaterial. As in many other nanomaterials, its unique properties are derived from its exceptional dimensions. One of these properties is its linear dispersion equation that implies charge carriers with extraordinary high mobility. Therefore, the electronic properties of the material can lead to a big improvement in the performance of known electronic devices, or even result in novel devices for a post-silicon era.

Atomistic modeling of Ge damage accumulation, amorphization and solid phase epitaxial regrowth

En los últimos años, el Ge ha ganado de nuevo atención con la finalidad de ser integrado en el seno de las existentes tecnologías de microelectrónica. Aunque no se le considera como un canddato capaz de reemplazar completamente al Si en el futuro próximo, probalemente servirá como un excelente complemento para aumentar las propiedades eléctricas en dispositivos futuros, especialmente debido a su alta movilidad de portadores. Esta integración requiere de un avance significativo del estado del arte en los procesos de fabricado. Técnicas de simulación, como los algoritmos de Monte Carlo cinético (KMC), proporcionan un ambiente atractivo para llevar a cabo investigación y desarrollo en este campo, especialmente en términos de costes en tiempo y financiación. En este estudio se han usado, por primera vez, técnicas de KMC con el fin entender el procesado “front-end” de Ge en su fabricación, específicamente la acumulación de dañado y amorfización producidas por implantación iónica y el crecimiento epitaxial en fase sólida (SPER) de las capas amorfizadas. Primero, simulaciones de aproximación de clisiones binarias (BCA) son usadas para calcular el dañado causado por cada ión. La evolución de este dañado en el tiempo se simula usando KMC sin red, o de objetos (OKMC) en el que sólamente se consideran los defectos. El SPER se simula a través de una aproximación KMC de red (LKMC), siendo capaz de seguir la evolución de los átomos de la red que forman la intercara amorfo/cristalina. Con el modelo de amorfización desarrollado a lo largo de este trabajo, implementado en un simulador multi-material, se pueden simular todos estos procesos. Ha sido posible entender la acumulación de dañado, desde la generación de defectos puntuales hasta la formación completa de capas amorfas. Esta acumulación ocurre en tres regímenes bien diferenciados, empezando con un ritmo lento de formación de regiones de dañado, seguido por una rápida relajación local de ciertas áreas en la fase amorfa donde ambas fases, amorfa y cristalina, coexisten, para terminar en la amorfización completa de capas extensas, donde satura el ritmo de acumulación. Dicha transición ocurre cuando la concentración de dañado supera cierto valor límite, el cual es independiente de las condiciones de implantación. Cuando se implantan los iones a temperaturas relativamente altas, el recocido dinámico cura el dañado previamente introducido y se establece una competición entre la generación de dañado y su disolución. Estos efectos se vuelven especialmente importantes para iones ligeros, como el B, el cual crea dañado más diluido, pequeño y distribuido de manera diferente que el causado por la implantación de iones más pesados, como el Ge. Esta descripción reproduce satisfactoriamente la cantidad de dañado y la extensión de las capas amorfas causadas por implantación iónica reportadas en la bibliografía. La velocidad de recristalización de la muestra previamente amorfizada depende fuertemente de la orientación del sustrato. El modelo LKMC presentado ha sido capaz de explicar estas diferencias entre orientaciones a través de un simple modelo, dominado por una única energía de activación y diferentes prefactores en las frecuencias de SPER dependiendo de las configuraciones de vecinos de los átomos que recristalizan. La formación de maclas aparece como una consecuencia de esta descripción, y es predominante en sustratos crecidos en la orientación (111)Ge. Este modelo es capaz de reproducir resultados experimentales para diferentes orientaciones, temperaturas y tiempos de evolución de la intercara amorfo/cristalina reportados por diferentes autores. Las parametrizaciones preliminares realizadas de los tensores de activación de tensiones son también capaces de proveer una buena correlación entre las simulaciones y los resultados experimentales de velocidad de SPER a diferentes temperaturas bajo una presión hidrostática aplicada. Los estudios presentados en esta tesis han ayudado a alcanzar un mejor entendimiento de los mecanismos de producción de dañado, su evolución, amorfización y SPER para Ge, además de servir como una útil herramienta para continuar el trabajo en este campo. In the recent years, Ge has regained attention to be integrated into existing microelectronic technologies. Even though it is not thought to be a feasible full replacement to Si in the near future, it will likely serve as an excellent complement to enhance electrical properties in future devices, specially due to its high carrier mobilities. This integration requires a significant upgrade of the state-of-the-art of regular manufacturing processes. Simulation techniques, such as kinetic Monte Carlo (KMC) algorithms, provide an appealing environment to research and innovation in the field, specially in terms of time and funding costs. In the present study, KMC techniques are used, for the first time, to understand Ge front-end processing, specifically damage accumulation and amorphization produced by ion implantation and Solid Phase Epitaxial Regrowth (SPER) of the amorphized layers. First, Binary Collision Approximation (BCA) simulations are used to calculate the damage caused by every ion. The evolution of this damage over time is simulated using non-lattice, or Object, KMC (OKMC) in which only defects are considered. SPER is simulated through a Lattice KMC (LKMC) approach, being able to follow the evolution of the lattice atoms forming the amorphous/crystalline interface. With the amorphization model developed in this work, implemented into a multi-material process simulator, all these processes can be simulated. It has been possible to understand damage accumulation, from point defect generation up to full amorphous layers formation. This accumulation occurs in three differentiated regimes, starting at a slow formation rate of the damage regions, followed by a fast local relaxation of areas into the amorphous phase where both crystalline and amorphous phases coexist, ending in full amorphization of extended layers, where the accumulation rate saturates. This transition occurs when the damage concentration overcomes a certain threshold value, which is independent of the implantation conditions. When implanting ions at relatively high temperatures, dynamic annealing takes place, healing the previously induced damage and establishing a competition between damage generation and its dissolution. These effects become specially important for light ions, as B, for which the created damage is more diluted, smaller and differently distributed than that caused by implanting heavier ions, as Ge. This description successfully reproduces damage quantity and extension of amorphous layers caused by means of ion implantation reported in the literature. Recrystallization velocity of the previously amorphized sample strongly depends on the substrate orientation. The presented LKMC model has been able to explain these differences between orientations through a simple model, dominated by one only activation energy and different prefactors for the SPER rates depending on the neighboring configuration of the recrystallizing atoms. Twin defects formation appears as a consequence of this description, and are predominant for (111)Ge oriented grown substrates. This model is able to reproduce experimental results for different orientations, temperatures and times of evolution of the amorphous/crystalline interface reported by different authors. Preliminary parameterizations for the activation strain tensors are able to also provide a good match between simulations and reported experimental results for SPER velocities at different temperatures under the appliance of hydrostatic pressure. The studies presented in this thesis have helped to achieve a greater understanding of damage generation, evolution, amorphization and SPER mechanisms in Ge, and also provide a useful tool to continue research in this field.

Fenología y capacidad de dispersión de Monochamus galloprovincialis (Olivier 1795) en la Península Ibérica = Phenology and dispersal ability of Monochamus galloprovincialis (Olivier 1795) at Iberian Peninsula

La aparición y avance de la enfermedad del marchitamiento del pino (Pine Wilt Desease, PWD), causada por Bursaphelenchus xylophilus (Nematoda; Aphelenchoididae), el nematodo de la madera del pino (NMP), en el suroeste de Europa, ha puesto de manifiesto la necesidad de estudiar la fenología y la dispersión de su único vector conocido en Europa, Monochamus galloprovincialis (Col., Cerambycidae). El análisis de 12 series de emergencias entre 2010 y 2014, registradas en Palencia, València y Teruel, con material procedente de diversos puntos de la península ibérica, demostró una alta variabilidad en la fenología de M. galloprovincialis y la divergencia térmica respecto de las poblaciones portuguesas. Para éstas, el establecimiento de los umbrales térmicos de desarrollo de las larvas post-dormantes del vector (12,2 y 33,5ºC) permitió la predicción de la emergencia mediana para la fecha en la que se acumulaban de 822 grados-día. Ninguna de las series analizadas en este trabajo necesitó de dichos grados-día estimados para la emergencia mediana. Asimismo, la emergencia se adelantó en las regiones más calurosas, mientras que se retrasó en las zonas más templadas. Más allá de la posible variabilidad entre poblaciones locales peninsulares, se detectaron indicios de que la diferencia en la acumulación de calor durante el otoño puede afectar el grado de maduración de las larvas invernantes, y su posterior patrón temporal de emergencia. Por último, también fueron observados comportamientos de protandria en las emergencias. Respecto a la fenología de su vuelo, entre los años 2010 y 2015, fueron ejecutados un total de 8 experimentos de captura de M. galloprovincialis mediante trampas cebadas con atrayentes en diferentes regiones (Castellón, Teruel, Segovia y Alicante) permitiendo el seguimiento del periodo de vuelo. Su análisis permitió constatar la disminución de las capturas y el acortamiento del periodo de vuelo con la altitud, el inicio del vuelo en el mes de mayo/junio a partir de los 14ºC de temperatura media diaria, la influencia de las altas temperaturas en la disminución de las capturas estivales (potencial causante de perfiles bimodales en las curvas de vuelo en las zonas menos frías), la evolución de la proporción de sexos a lo largo del periodo de vuelo (que muestra una mayor captura de hembras al inicio y de machos al final) y el comportamiento diurno y ligado a las altas temperaturas del vuelo circadiano del insecto. Dos redes de muestreo sistemático de insectos saproxílicos instaladas en la Comunitat Valencia (Red MUFFET, 15 parcelas, año 2013) y en Murcia (Red ESFP, 20 parcelas, años 2008-2010) permitieron el estudio de la comunidad de insectos relacionada con M. galloprovincialis. Cada una de las parcelas contaba con una trampa cebada con atrayentes y una estación meteorológica. El registro de más de 250 especies de coleópteros saproxílicos demostró el potencial que tiene el empleo de redes de trampas vigía para la detección temprana de organismos exóticos, además de permitir la caracterización y evaluación de las comunidades de entomofauna útil, representando una de las mejores herramientas de la gestión integrada de plagas. En este caso, la comunidad de saproxílicos estudiada mostró ser muy homogénea respecto a la variación ambiental de las zonas de muestreo, y que pese a las pequeñas variaciones entre las comunidades de los diferentes ecosistemas, el rol que M. galloprovincialis desempeña en ellas a lo largo de todo el gradiente estudiado es el mismo. Con todo, el análisis mediante redes de interacción mostró su relevancia ecológica al actuar de conector entre los diferentes niveles tróficos. Por último, un total de 12 experimentos de marcaje-liberación-recaptura desarrollados entre 2009 y 2012 en Castellón, Teruel, Valencia y Murcia permitieron evaluar el comportamiento dispersivo de M. galloprovincialis. Las detecciones mediante trampas cebadas de los insectos liberados se dieron por lo menos 8 días después de la emergencia. La abundancia de población pareció relacionada con la continuidad, la naturalización de la masa, y con la afección previa de incendios. La dispersión no estuvo influida por la dirección ni la intensidad de los vientos dominantes. La abundancia de material hospedante (en lo referente a las variables de masa y a los índices de competencia) influyó en la captura del insecto en paisajes fragmentados, aunque la ubicación de las trampas optimizó el número de capturas cuando se ubicaron en el límite de la masa y en zonas visibles. Por último también se constató que M. galloprovincialis posee suficiente capacidad de dispersión como para recorrer hasta 1500 m/día, llegando a alcanzar distancias máximas de 13600m o de 22100 m. ABSTRACT The detection and expansion of the Pine Wilt Desease (PWD), caused by Bursaphelenchus xylophilus (Nematoda; Aphelenchoididae), Pine Wood Nematode (PWN), in southwestern Europe since 1999, has triggered off the study of the phenology and the dispersion of its unique vector in the continent, Monochamus galloprovincialis (Coleoptera, Cerambycidae). The analysis of 12 emergence series between 2010 and 2014 registered in Palencia, Teruel and Valencia (Spain), registered from field colonized material collected at several locations of the Iberian Peninsula, showed a high variability in the emergence phenology of M. galloprovincialis. In addition, these patterns showed a very acute thermal divergence regarding a development model fitted earlier in Portugal. Such model forecasted the emergence of 50% of M. galloprovincialis individuals in the Setúbal Peninsula (Portugal) when an average of 822 degree-days (DD) were reached, based on the accumulation of heat from the 1st of March until emergence and lower and upper thresholds of 12.2 ºC and 33,5 °C respectively. In our results, all analyzed series needed less than 822 DD to complete the 50% of the emergence. Also, emergency occurred earlier in the hottest regions, while it was delayed in more temperate areas. Beyond the possible variability between local populations, the difference in the heat accumulation during the fall season may have affected the degree of maturation of overwintering larvae, and subsequently, the temporal pattern of M. galloprovincialis emergences. Therefore these results suggest the need to differentiate local management strategies for the PWN vector, depending on the location, and the climatic variables of each region. Finally, protandrous emergence patterns were observed for M. galloprovincialis in most of the studied data-sets. Regarding the flight phenology of M. galloprovincialis, a total of 8 trapping experiments were carried out in different regions of the Iberian Peninsula (Castellón, Teruel, Segovia and Alicante) between 2010 and 2015. The use of commercial lures and traps allowed monitoring of the flight period of M. galloprovincialis. The analyses of such curves, helped confirming different aspects. First, a decline in the number of catches and a shortening of the flight period was observed as the altitude increased. Flight period was recorded to start in May / June when the daily average temperature went over 14 ° C. A significant influence of high temperatures on the decrease of catches in the summer was found in many occasions, which frequently lead to a bimodal profile of the flight curves in warm areas. The evolution of sex ratio along the flight period shows a greater capture of females at the beginning of the period, and of males at the end. In addition, the circadian response of M. galloprovincialis to lured traps was described for the first time, concluding that the insect is diurnal and that such response is linked to high temperatures. Two networks of systematic sampling of saproxylic insects were installed in the Region of Valencia (Red MUFFET, 15 plots, 2013) and Murcia (Red ICPF, 20 plots, 2008-2010). These networks, intended to serve the double purpose of early-detection and long term monitoring of the saproxylic beetle assemblies, allowed the study of insect communities related to M. galloprovincialis. Each of the plots had a trap baited with attractants and a weather station. The registration of almost 300 species of saproxylic beetles demonstrated the potential use of such trapping networks for the early detection of exotic organisms, while at the same time allows the characterization and evaluation of useful entomological fauna communities, representing one of the best tools for the integrated pest management. In this particular case, the studied community of saproxylic beetles was very homogeneous with respect to environmental variation of the sampling areas, and despite small variations between communities of different ecosystems, the role that M. galloprovincialis apparently plays in them across the studied gradient seems to be the same. However, the analysis through food-webs showed the ecological significance of M. galloprovincialis as a connector between different trophic levels. Finally, 12 mark-release-recapture experiments were carried out between 2009 and 2012 in Castellón, Teruel, Valencia and Murcia (Spain) with the aim to describe the dispersive behavior of M. galloprovincialis as well as the stand and landscape characteristics that could influence its abundance and dispersal. No insects younger than 8 days were caught in lured traps. Population abundance estimates from mark-release-recapture data, seemed related to forest continuity, naturalization, and to prior presence of forest fires. On the other hand, M. galloprovincialis dispersal was not found to be significantly influenced by the direction and intensity of prevailing winds. The abundance of host material, very related to stand characteristics and spacing indexes, influenced the insect abundance in fragmented landscapes. In addition, the location of the traps optimized the number of catches when they were placed in the edge of the forest stands and in visible positions. Finally it was also found that M. galloprovincialis is able to fly up to 1500 m / day, reaching maximum distances of up to 13600 m or 22100 m.

Persuasive system design methods to deliver a cardio-rehabilitation program of post mi outpatients

Las enfermedades no transmisibles provocan cada ano 38 millones de fallecimientos en el mundo. Entre ellas, tan solo cuatro enfermedades son responsables del 82% de estas muertes: las enfermedades cardiovasculares, las enfermedades crónicas respiratorias, la diabetes, y el cáncer. Se prevé que estas cifras aumenten en los próximos anos, ya que las tendencias indican que en el año 2030 las muertes por esta causa ascenderán a 53 millones de personas. La Organización Mundial de la Salud (OMS) considera importante buscar soluciones para afrontar esta situación y ha solicitado a los gobiernos del mundo la implementación de intervenciones para mejorar los hábitos de vida de las personas y reducir así el riesgo de desarrollo de enfermedades no trasmisibles. Cada año se producen 32 millones de infartos de miocardio y derrames celebrales, de los cuales 12.5 son mortales. En el mundo entre el 40% y 75% de la víctimas de un infarto de miocardio mueren antes de su ingreso en el hospital. En los casos que sobreviven, la adopción de un estilo de vida saludable puede evitar infartos sucesivo, y supone un ahorro potencial de 6 billones de euros al año. La rehabilitación cardiaca es un programa individualizado que aplica un método multidisciplinar para ayudar al paciente a recuperar su condición física, a gestionar la enfermedad cardiovascular y sus comorbilidades, a adoptar hábitos de vida saludables, y a promover su salud mental. La rehabilitación cardiaca requiere la total involucración y motivación del paciente, solo de esta manera se podrán promover hábitos saludables y mejorar la gestión y prevención de su enfermedad. Aunque la participación en los programas de rehabilitación cardiaca es baja, hoy en día existen programas de rehabilitación cardiaca que el paciente puede realizar en su casa. Estos suponen una solución prometedora para aumentar la participación. La rehabilitación cardiaca se considera una intervención integral donde los modelos de psicología de la salud son aplicados para promover un cambio en el estilo de vida de las personas así como para ayudarles a afrontar su propia enfermedad. Existen métodos para implementar cambios de hábitos y de aptitud, y también se considera muy relevante promover no solo el bienestar físico sino también el mental. Existen tecnologías que promueven los cambios de comportamientos en los seres humanos. En concreto, las tecnologías persuasivas y los sistemas de apoyo al cambio de comportamientos modelan las características, las estrategias y los métodos de diseño para promover cambios usando la tecnología. Pero estos modelos tienen algunas limitaciones: todavía no se ha definido que rol tienen las emociones en el cambio de comportamientos y como traducir los métodos de la psicología de la salud en la tecnología. Esta tesis se centra en tres elementos que tienen un rol clave en los cambios de hábitos y actitud: el estado físico, el estado mental, y la tecnología. -Estado de salud: un estado de salud critico puede modificar la actitud del ser humano respecto al cambio. A la vez un buen estado de salud hace que la necesidad del cambio sea menos percibida. -Estado emocional: la actitud tiene un componente afectivo. Los estados emocionales negativos pueden reducir la habilidad de una persona para adoptar nuevos comportamientos. La salud mental es la situación ideal donde los individuos tienen predisposición a los cambios. La tecnología puede ayudar a las personas a adoptar nuevos hábitos, así como a mantener una salud física y mental. Este trabajo de investigación se centra en el diseño de tecnologías para la mejora del estado físico y emocional de las personas. Se ha propuesto un marco de diseño llamado “Well.Be.Sign”. El marco se basa en tres aspectos: El marco teórico: representa los elementos que se tienen que definir para diseñar tecnologías para promover el bienestar de las personas. -El diagrama de influencia: presenta las fuerzas de ‘persuasión’ en el contexto de la salud. El rol de las tecnologías persuasivas ha sido contextualizado en una dimensión donde otros elementos influencian el usuario.  El proceso de diseño: describe el proceso de diseño utilizando una metodología iterativa e incremental que aplica una combinación de métodos de diseño existentes (Diseño Orientado a Objetivos, Diseño de Sistemas Persuasivos) así como elementos originales de este trabajo de investigación. Los métodos se han aplicados para diseñar un sistema que ofrezca un programa de tele-rehabilitación cardiaca. Inicialmente se ha diseñado un prototipo de acuerdo con las necesidades del usuario. En segundo lugar, el prototipo se ha extendido especificando la intervención requerida para al programa de rehabilitación cardiaca. Finalmente el sistema se ha desarrollado y validado en un ensayo clínico con grupo control, donde se observaron las variaciones del estado cardiovascular, el nivel de conocimiento acerca de la enfermedad, la percepción de la enfermedad, la persistencia de hábitos saludables, y la aceptabilidad del sistema. Los resultados muestran que el grupo de intervención tiene una superior capacidad cardiovascular, mejor conocimiento acerca de la enfermedad, y más percepción de control de la enfermedad. Asimismo, en algunos casos se ha registrado persistencia de los hábitos de ejercicios 6 meses después del uso del sistema. Otros dos estudios se han presentado para demonstrar la relevancia del estado emocional del usuario en el diseño de aplicaciones para la promoción del bienestar.  En personas con una grave enfermedad crónica como la insuficiencia cardiaca, donde se ha presentado las conexiones entre estado de salud y estado emocional. En el estudio se ensena la relaciones que tienen los síntomas y las emociones negativas y como un estado negativo emocional puede empeorar la condición física del paciente. -Personas con trastornos del humor: el estudio muestra como las emociones pueden tener un impacto en la percepción de la tecnología por parte del usuario. ABSTRACT Noncommunicable diseases (NCDs) cause the death of 38 million people every year. Four major NCDs are responsible for 82% of these deaths: cardio vascular disease, chronic respiratory disease, diabetes and cancer. These pandemic numbers are projected to raise to 53 million deaths in 2030, and for this reason the assembly of the World Health Organization (WHO) considers communicable diseases as an urgent need to be addressed. It is also a trend to advocate the adoption of mobile technology to deliver health services and to promote healthy behaviours among citizens, but adopting healthS promoting lifestyle is still a difficult task facing human tendencies. Within this context, there is a promising opportunity: persuasive technologies. These technologies are intentionally designed to change a person’s attitudes or behaviours; when applied in this context, than can be used to change health-related attitudes, beliefs, and behaviours. Each year there are 32 million heart attacks and strokes globally, of which about 12.5 million are fatal. Worldwide between 40 and 75% of all heart-attack victims die before reaching hospital. Avoiding a second heart attack by improving adherence to lifestyle and medication regimens has a cost saving potential of around €6 billion per year. In most of the cases the cardiovascular event has been provoked by unhealthy lifestyle. Furthermore, after an MI event the patient's decision to adopt or not healthier behaviour will influence the progress of the disease. Cardio-rehabilitation is an individualized program that follows a multidisciplinary approach to support the user to recover from the Myocardial Infarction, manage the Cardio Vascular Disease and the comorbidities, adopt healthy habits, and cope with any emotional distress. Cardio- rehabilitation requires patient participation and willingness to perform behavioral modifications and change the attitude toward the management and prevention of the disease. Participation in the Cardio Rehabilitation program is not high; the home-based rehabilitation program is a promising solution to increase participation. Nowadays cardio rehabilitation is considered a comprehensive intervention in which models of health psychology are applied to promote the behaviour change of the individuals. Relevant methods that have been successfully applied to foster healthy habits include the Health Belief Model and the Trans Theoretical Model. Studies also demonstrate the importance to promote not only the physical but also the mental well being of the individuals. The idea of also promoting behaviour change using technologies has been defined by the literature as persuasive technologies or behaviour change support systems, in which the features, the strategies and the design method have been modelled to foster the behaviour change using technology. Limitations have been found in this model: there is still research to be done on the role of the emotions and how psychological health intervention can be translated into computer methods. This research focuses on three elements that could foster behaviour change in individuals: the physical and emotional status of the person, and the technology. Every component can influence the user's attitude and behaviour in the following ways: ' Physical status: bad physical status could change human attitude toward the necessity to adopt health behaviours; at the same time, good health status reduces the need to adopt healthy habits. ' Emotional status: the attitude has an affective component, negative emotional state can reduce the ability of a person to adopt new behaviours, and mental well being is the ideal situation in which individuals have a predisposition to adopt healthy behaviours. ' Technology: it can help users to adopt new behaviours and can also be support to promote physical and emotional status. Following this approach the idea driven in this research is that technology that is designed to improve the physical status and the emotional status of the individual could better foster behaviour change. According to this principle, the Well.Be.Sign framework has been proposed. The framework is based on three views: ' The theoretical framework: it represents the patterns that have to be defined to design the technologies to promote well being. ' The influence diagram: it shows the persuasive forces in the context of health care. The role of the persuasive technologies is contextualized in a wider universe where other factors and persuasive forces influence a patient. ' The design process: it shows the process of design using an iterative, incremental methodology that applies a combination of existing methodologies (Goal Directed Design and Persuasive System Design) and others that are original to this research. The methods have been applied to design a system to deliver cardio rehabilitation at home: first a prototype has been defined according to the user’s needs, then it has been extended with the specific intervention required for the cardio–rehabilitation, finally the system has been developed and validated in a controlled clinical study in which the cardiovascular fitness, the level of knowledge, the perception of the illness, the persistence of healthy habits and the system acceptance (only the intervention group) were measured. The results show that the intervention group increased cardiovascular capacity, knowledge, feeling of control of illness and perceived benefits of exercise at the end of the study. After six months of the study, a followSup of the exercise habits was performed. Some individuals of the intervention group continued to be engaged in the running exercise sessions promoted in the designed system. Two other cases have been presented to demonstrate the foundations of the Well.Be.Sign’s approach to promote both physical and emotional status: ' People affected by Heart Failure, in which a bidirectional connection between health status and emotions has been discussed with patients. Two correlations were demonstrated: the relationship between symptoms and negative emotional response, and that negative emotional status is correlated with worsening of chronic conditions. ' People with mood disorders: the study shows that emotions could also impact how the user perceives the technology.