Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for diesel passenger cars. Likewise, the CO, NOX and HC emissions were compared for each driving style for the tested vehicles. Eco-driving reduces by 14% fuel consumption and CO2 emissions, but aggressive driving increase consumption by 40%. Aggressive driving increases NOX emission by more than 40%. CO and HC, show different trends, but being increased in eco-driving style.

Proposal of a dynamic performance index to analyze driving pattern effect on car emissions

The contributions of driver behaviour as well as surrounding infrastructure are decisive on pollutant emissions from vehicles in real traffic situations. This article deals with the preliminary study of the interaction between the dynamic variables recorded in a vehicle (driving pattern) and pollutant emissions produced over a given urban route. It has been established a “dynamic performance index”-DPI, which is calculated from some driving pattern parameters, which in turn depends on traffic congestion level and route characteristics, in order to determine whether the driving has been aggressive, normal or calm. Two passenger cars instrumented with a portable activity measurement system -to record dynamic variables- and on-board emission measurement equipment have been used. This study has shown that smooth driving patterns can reduce up to 80% NOX emissions and up to 20% of fuel in the same route

Environmental assessment of low speed policies for motor vehicle mobility in city centres

streets in local residential areas in large cities, real traffic tests for pollutant emissions and fuel consumption have been carried out in Madrid city centre. Emission concentration and car activity were simultaneously measured by a Portable Emissions Measurement System. Real life tests carried out at different times and on different days were performed with a turbo-diesel engine light vehicle equipped with an oxidizer catalyst and using different driving styles with a previously trained driver. The results show that by reducing the speed limit from 50 km h-1 to 30 km h-1, using a normal driving style, the time taken for a given trip does not increase, but fuel consumption and NOx, CO and PM emissions are clearly reduced. Therefore, the main conclusion of this work is that reducing the speed limit in some narrow streets in residential and commercial areas or in a city not only increases pedestrian safety, but also contributes to reducing the environmental impact of motor vehicles and reducing fuel consumption. In addition, there is also a reduction in the greenhouse gas emissions resulting from the combustion of the fuel.

Design of a solar incubator. Part 1: Monitoring temperature and enthalpy gradients under commercial production

The real increase in energy prices and the intention of reducing pollutant emissions in developed countries makes interesting to use solar energy in all the processes where its application is possible. As it is demonstrated in countries sited at latitudes with optimal conditions of solar radiation and temperature, it is possible to use solar energy as heat source for small-scale hatchery [1,2], but beyond, making a design for proper installation; it is possible to use solar energy as main or support energy source in medium and large size incubators . Monitoring of a normal actual process using temperature and relative humidity sensors is necessary to know the actual operating conditions that the solar heating system must be designed and sized for. Moreover, the identification and analysis of temperature and enthalpy gradients inside the incubator is of major importance.

Modeling impact assessment of transport policies through a multiregional input-output integrated approach

El objetivo de esta investigación es desarrollar una metodología para estimar los potenciales impactos económicos y de transporte generados por la aplicación de políticas en el sector transporte. Los departamentos de transporte y otras instituciones gubernamentales relacionadas se encuentran interesadas en estos análisis debido a que son presentados comúnmente de forma errónea por la insuficiencia de datos o por la falta de metodologías adecuadas. La presente investigación tiene por objeto llenar este vacío haciendo un análisis exhaustivo de las técnicas disponibles que coincidan con ese propósito. Se ha realizado un análisis que ha identificado las diferencias cuando son aplicados para la valoración de los beneficios para el usuario o para otros efectos como aspectos sociales. Como resultado de ello, esta investigación ofrece un enfoque integrado que incluye un modelo Input-Output de múltiples regiones basado en la utilidad aleatoria (RUBMRIO), y un modelo de red de transporte por carretera. Este modelo permite la reproducción con mayor detalle y realismo del transporte de mercancías que por medio de su estructura sectorial identifica los vínculos de las compras y ventas inter-industriales dentro de un país utilizando los servicios del transporte de mercancías. Por esta razón, el modelo integrado es aplicable a diversas políticas de transporte. En efecto, el enfoque se ha aplicado para estudiar los efectos macroeconómicos regionales de la implementación de dos políticas diferentes en el sistema de transporte de mercancías de España, tales como la tarificación basada en la distancia recorrida por vehículo-kilómetro (€/km) aplicada a los vehículos del transporte de mercancías, y para la introducción de vehículos más largos y pesados de mercancías en la red de carreteras de España. El enfoque metodológico se ha evaluado caso por caso teniendo en cuenta una selección de la red de carreteras que unen las capitales de las regiones españolas. También se ha tenido en cuenta una dimensión económica a través de una tabla Input-Output de múltiples regiones (MRIO) y la base de datos de conteo de tráfico existente para realizar la validación del modelo. El enfoque integrado reproduce las condiciones de comercio observadas entre las regiones usando el sistema de transporte de mercancías por carretera, y que permite por comparación con los escenarios de políticas, determinar las contribuciones a los cambios distributivos y generativos. Así pues, el análisis estima los impactos económicos en cualquier región considerando los cambios en el Producto Interno Bruto (PIB) y el empleo. El enfoque identifica los cambios en el sistema de transporte a través de todos los caminos de la red de transporte a través de las medidas de efectividad (MOEs). Los resultados presentados en esta investigación proporcionan evidencia sustancial de que en la evaluación de las políticas de transporte, es necesario establecer un vínculo entre la estructura económica de las regiones y de los servicios de transporte. Los análisis muestran que para la mayoría de las regiones del país, los cambios son evidentes para el PIB y el empleo, ya que el comercio se fomenta o se inhibe. El enfoque muestra cómo el tráfico se desvía en ambas políticas, y también determina detalles de las emisiones de contaminantes en los dos escenarios. Además, las políticas de fijación de precios o de regulación de los sistemas de transporte de mercancías por carretera dirigidas a los productores y consumidores en las regiones promoverán transformaciones regionales afectando todo el país, y esto conduce a conclusiones diferentes. Así mismo, este enfoque integrado podría ser útil para evaluar otras políticas y otros países en todo el mundo. The purpose of this research is to develop a methodological approach aimed at assessing the potential economic and transportation impacts of transport policies. Transportation departments and other related government parties are interested in such analysis because it is commonly misrepresented for the insufficiency of data and suitable methodologies available. This research is directed at filling this gap by making a comprehensive analysis of the available techniques that match with that purpose. The differences when they are applied for the valuation of user benefits or for other impacts as social matters have been identified. As a result, this research presents an integrated approach which includes both a random utility-based multiregional Input-Output model (RUBMRIO), and a road transport network model. This model accounts for freight transport with more detail and realism because its commodity-based structure traces the linkages of inter-industry purchases and sales that use freight services within a given country. For this reason, the integrated model is applicable to various transport policies. In fact, the approach is applied to study the regional macroeconomic effects of implementing two different policies in the freight transport system of Spain, such as a distance-based charge in vehicle-kilometer (€/km) for Heavy Goods Vehicles (HGVs), and the introduction of Longer and Heavier Vehicles (LHVs) in the road network of Spain. The methodological approach has been evaluated on a case by case basis considering a selected road network of highways linking the capitals of the Spanish regions. It has also considered an economic dimension through a Multiregional Input Output Table (MRIO) and the existing traffic count database used in the model validation. The integrated approach replicates observed conditions of trade among regions using road freight transport systems that determine contributions to distributional and generative changes by comparison with policy scenarios. Therefore, the model estimates economic impacts in any given area by considering changes in Gross Domestic Product (GDP), employment (jobs), and in the transportation system across all paths of the transport network considering Measures of effectiveness (MOEs). The results presented in this research provide substantive evidence that in the assessment of transport policies it is necessary to establish a link between the economic structure of regions and the transportation services. The analysis shows that for most regions in the country, GDP and employment changes are noticeable when trade is encouraged or discouraged. This approach shows how traffic is diverted in both policies, and also provides details of the pollutant emissions in both scenarios. Furthermore, policies, such as pricing or regulation of road freight transportation systems, directed to producers and consumers in regions will promote different regional transformations across the country, and this lead to different conclusions. In addition, this integrated approach could be useful to assess other policies and countries worldwide.

Changes in the external costs of freight surface transport in Spain

This paper studies the external costs of surface freight transport in Spain and finds that a reduction occurred over the past 15 years. The analysis yields two conclusions: trucks have experienced a reduction in external costs, and rail has lower externalities. The external costs of road freight transport decrease between 1993 and 2007 (44%). The external costs of rail freight increase by 12%. During this period, the external costs of road freight related to climate increase by 16%, oppositely than those from air pollution and accidents (51 and 44%). The external costs of rail related to pollutant emissions and climate increase by 4% and 43%. Oppositely, the external costs related to accidents decrease by 27%. Road freight generates eight times the external costs of rail, 2.35 Euro cents per tonne kilometre in 2005 (5.6% accidents, 74.7% air pollution and 19.7% climate) vs. 0.28 (13.4% accidents, 53.9% air pollution and 32.7% climate).

Impact of introducing longer and heavier vehicles on regional consumer price index and Spanish road freight transport system

This paper applies an integrated modeling approach to the case of Spain; the approach is based on a random utility-based multiregional input-output model and a road transport network model for assessing the effect of introducing longer and heavier vehicles (LHVs) on the regional consumer price index (CPI) and on the transportation system. The approach strongly supports the concept that changes in transport costs derived from the LHV allowance as well as the economic structure of regions have direct and indirect effects on the economy and on the transportation system. Results show that the introduction of LHVs might reduce prices paid by consumers for a representative basket of goods and services in the regions of Spain and would also lead to a reduction in the regional CPI. In addition, the magnitude and extent of changes in the transportation system are estimated by using the commodity-based structure of the approach to identify the effect of traffic changes on traffic flows and on pollutant emissions over the whole network.

Modelización de una central térmica supercrítica de 700 MW con captura de CO₂

El objetivo de este proyecto es realizar la simulación de una central térmica supercrítica de 700 MW con captura de CO₂ para producir electricidad y verterla a la red. El proyecto describe los equipos e instalaciones de la central y define los balances técnicos de la misma, probando que es viable técnicamente la incorporación de una planta de captura de CO₂ a una central térmica, a pesar del bajo rendimiento de la central. Además incluye el estudio económico que indica la viabilidad económica del proyecto, aunque con una rentabilidad baja. Este proyecto mira hacia el futuro debido a la necesidad de reducir las emisiones contaminantes, ya de casi la misma importancia que generar electricidad, y demuestra que es posible generar una energía limpia en centrales de carbón. ABSTRACT The purpose of this project is to carry out the simulation of a 700 MW supercritical coal thermal power plant with CO₂ capture to produce electricity and send it to the grid. The project describes the equipment, the installations and defines technical balances of the power plant. It shows that a CO₂ capture plant in a coal power plant is technically possible, in spite of the low power plant efficiency. In addition, it includes the economic analysis that shows the economic viability of the project, with a low profitability. This project looks into the future due to the need of reducing the pollutant emissions, which are almost as important as the generation of electricity, and demonstrates that a green energy in coal power plants is possible.

Metodología para la asignación de vehículos de una flota a rutas preestablecidas

En general, la distribución de una flota de vehículos que recorre rutas fijas no se realiza completamente en base a criterios objetivos, primando otros aspectos más difícilmente cuantificables. El análisis apropiado debería tener en consideración la variabilidad existente entre las diferentes rutas dentro de una misma ciudad para así determinar qué tecnología es la que mejor se adapta a las características de cada itinerario. Este trabajo presenta una metodología para optimizar la asignación de una flota de vehículos a sus rutas, consiguiendo reducir el consumo y las emisiones contaminantes. El método propuesto está organizado según el siguiente procedimiento: - Registro de las características cinemáticas de los vehículos que recorren un conjunto representativo de rutas. - Agrupamiento de las líneas en conglomerados de líneas similares empleando un algoritmo jerárquico que optimice el índice de semejanza entre rutas obtenido mediante contraste de hipótesis de las variables representativas. - Generación de un ciclo cinemático específico para cada conglomerado. - Tipificación de variables macroscópicas que faciliten la clasificación de las restantes líneas utilizando una red neuronal entrenada con la información recopilada en las rutas medidas. - Conocimiento de las características de la flota disponible. - Disponibilidad de un modelo que estime, según la tecnología del vehículo, el consumo y las emisiones asociados a las variables cinemáticas de los ciclos. - Desarrollo de un algoritmo de reasignación de vehículos que optimice una función objetivo dependiente de las emisiones. En el proceso de optimización de la flota se plantean dos escenarios de gran trascendencia en la evaluación ambiental, consistentes en minimizar la emisión de dióxido de carbono y su impacto como gas de efecto invernadero (GEI), y alternativamente, la producción de nitróxidos, por su influencia en la lluvia ácida y en la formación de ozono troposférico en núcleos urbanos. Además, en ambos supuestos se introducen en el problema restricciones adicionales para evitar que las emisiones de las restantes sustancias superen los valores estipulados según la organización de la flota actualmente realizada por el operador. La metodología ha sido aplicada en 160 líneas de autobús de la EMT de Madrid, conociéndose los datos cinemáticos de 25 rutas. Los resultados indican que, en ambos supuestos, es factible obtener una redistribución de la flota que consiga reducir significativamente la mayoría de las sustancias contaminantes, evitando que, en contraprestación, aumente la emisión de cualquier otro contaminante. ABSTRACT In general, the distribution of a fleet of vehicles that travel fixed routes is not usually implemented on the basis of objective criteria, thus prioritizing on other features that are more difficult to quantify. The appropriate analysis should consider the existing variability amongst the different routes within the city in order to determine which technology adapts better to the peculiarities of each itinerary. This study proposes a methodology to optimize the allocation of a fleet of vehicles to the routes in order to reduce fuel consumption and pollutant emissions. The suggested method is structured in accordance with the following procedure: - Recording of the kinematic characteristics of the vehicles that travel a representative set of routes. - Grouping of the lines in clusters of similar routes by utilizing a hierarchical algorithm that optimizes the similarity index between routes, which has been previously obtained by means of hypothesis contrast based on a set of representative variables. - Construction of a specific kinematic cycle to represent each cluster of routes. - Designation of macroscopic variables that allow the classification of the remaining lines using a neural network trained with the information gathered from a sample of routes. - Identification and comprehension of the operational characteristics of the existing fleet. - Availability of a model that evaluates, in accordance with the technology of the vehicle, the fuel consumption and the emissions related with the kinematic variables of the cycles. - Development of an algorithm for the relocation of the vehicle fleet by optimizing an objective function which relies on the values of the pollutant emissions. Two scenarios having great relevance in environmental evaluation are assessed during the optimization process of the fleet, these consisting in minimizing carbon dioxide emissions due to its impact as greenhouse gas (GHG), and alternatively, the production of nitroxides for their influence on acid rain and in the formation of tropospheric ozone in urban areas. Furthermore, additional restrictions are introduced in both assumptions in order to prevent that emission levels for the remaining substances exceed the stipulated values for the actual fleet organization implemented by the system operator. The methodology has been applied in 160 bus lines of the EMT of Madrid, for which kinematic information is known for a sample consisting of 25 routes. The results show that, in both circumstances, it is feasible to obtain a redistribution of the fleet that significantly reduces the emissions for the majority of the pollutant substances, while preventing an alternative increase in the emission level of any other contaminant.

Conceptual design of offshore platform supply vessel based on hybrid diesel generator-fuel cell power plant

Nowadays increasing fuel prices and upcoming pollutant emission regulations are becoming a growing concern for the shipping industry worldwide. While fuel prices will keep rising in future years, the new International Convention for the Prevention of Pollution from Ships (MARPOL) and Sulphur Emissions Control Areas (SECA) regulations will forbid ships to use heavy fuel oils at certain situations. To fulfil with these regulations, the next step in the marine shipping business will comprise the use of cleaner fuels on board as well as developing new propulsion concept. In this work a new conceptual marine propulsion system is developed, based on the integration of diesel generators with fuel cells in a 2850 metric tonne of deadweight platform supply vessel. The efficiency of the two 250 kW methanol-fed Solid Oxide Fuel Cell (SOFC) system installed on board combined with the hydro dynamically optimized design of the hull of the ship will allow the ship to successfully operate at certain modes of operation while notably reduce the pollutant emissions to the atmosphere. Besides the cogeneration heat obtained from the fuel cell system will be used to answer different heating needs on board the vessel

An integrated modeling approach to assess the impact on road freight transport demand of allowing longer and heavier vehicles (LHVs) in Spain

The assessment on introducing Longer and Heavier Vehicles (LHVs) on the road freight transport demand is performed in this paper by applying an integrated modeling approach composed of a Random Utility-Based Multiregional Input-Output model (RUBMRIO) and a road transport network model. The approach strongly supports the concept that changes in transport costs derived from the LHVs allowance as well as the economic structure of regions have both direct and indirect effects on the road freight transport system. In addition, we estimate the magnitude and extent of demand changes in the road freight transportation system by using the commodity-based structure of the approach to identify the effect on traffic flows and on pollutant emissions over the whole network of Spain by considering a sensitivity analysis of the main parameters which determine the share of Heavy-Goods Vehicles (HGVs) and LHVs. The results show that the introduction of LHVs will strengthen the competitiveness of the road haulage sector by reducing costs, emissions, and the total freight vehicles required.

Urban microclimate and thermal comfort modelling: strategies for urban renovation

The urban microclimate plays an important role in building energy consumption and thermal comfort in outdoor spaces. Nowadays, cities need to increase energy efficiency, reduce pollutant emissions and mitigate the evident lack of sustainability. In light of this, attention has focused on the bioclimatic concepts use in the urban development. However, the speculative unsustainability of the growth model highlights the need to redirect the construction sector towards urban renovation using a bioclimatic approach. The public space plays a key role in improving the quality of today’s cities, especially in terms of providing places for citizens to meet and socialize in adequate thermal conditions. Thermal comfort affects perception of the environment, so microclimate conditions can be decisive for the success or failure of outdoor urban spaces and the activities held in them. For these reasons, the main focus of this work is on the definition of bioclimatic strategies for existing urban spaces, based on morpho-typological components, urban microclimate conditions and comfort requirements for all kinds of citizens. Two case studies were selected in Madrid, in a social housing neighbourhood constructed in the 1970s based on Rational Architecture style. Several renovation scenarios were performed using a computer simulation process based in ENVI-met and diverse microclimate conditions were compared. In addition, thermal comfort evaluation was carried out using the Universal Thermal Climate Index (UTCI) in order to investigate the relationship between microclimate conditions and thermal comfort perception. This paper introduces the microclimate computer simulation process as a valuable support for decision-making for neighbourhood renovation projects in order to provide new and better solutions according to the thermal quality of public spaces and reducing energy consumption by creating and selecting better microclimate areas.

How lowering speed limits in an urban highway affects traffics performance and emissions: the case of Madrid M-30 ring-road

The city of Madrid keeps not meeting the GHG and air pollutant limits set by the European legislation. A broad range of strategies have being taken into account to reduce both types of emissions; however traffic management meas ures are usually consigned to the sidelines. In 2004, Madrid City Council launched a plan to re-design its inner ring-road supported by a socioeconomic study that evaluated the environmental and operational benefits of the project. For safety reasons the planned speed limit for the tunnel section was finally reduced from 90km/h to 70km/h. Using a Macroscopic Traffic Model and the European Air Pollutant and Emissions Inventory Guidebook (EMEP/EEA), this paper examines the environmental and traffic performance consequences of this decision. Results support the thesis that reduced speed limits leads to GHG and air pollution reductions in the area affected by the measure without substantially altering traffic performance. The implementation of the new speed limit policy brings about a 15% and 16% reduction in both CO2 and NOx emissions respectively. Emissions’ reduction during off-peak hours is larger than during peak hours.