Simplified computational method for non-linear seismic analysis of bridges

After the experience gained during the past years it seems clear that nonlinear analysis of bridges are very important to compute ductility demands and to localize potential hinges. This is specially true for irregular bridges in which it is not clear weather or not it is possible to use a linear computation followed by a correction using a behaviour factor. To simplify the numerical effort several approximate methods have been proposed. Among them, the so-called Dynamic Plastic Hinge Method in which an evolutionary shape function is used to reduce the structure to a single degree of freedom system seems to mantein a good balance between accuracy and simplicity. This paper presents results obtained in a parametric study conducted under the auspicies of PREC-8 european research program.

Seismic performance case study of bridge pile cap foundation

The purpose of this report is to build a model that represents, as best as possible, the seismic behavior of a pile cap bridge foundation by a nonlinear static (analysis) procedure. It will consist of a reproduction of a specimen already built in the laboratory. This model will carry out a pseudo static lateral and horizontal pushover test that will be applied onto the pile cap until the failure of the structure, the formation of a plastic hinge in the piles due to the horizontal deformation, occurs. The pushover test consists of increasing the horizontal load over the pile cap until the horizontal displacement wanted at the height of the pile cap is reached. The output of this model will be a Skeleton curve that will plot the lateral load (kN) over the displacement (m), so that the maximum movement the pile cap foundation can reach before its failure can be calculated. This failure will be achieved when the load at that specific shift is equal to 85% of the maximum. The pile cap foundation finite element model was based on pile cap built for a laboratory experiment already carried out by the Master student Deming Zhang at Tongji University. Two different pile caps were tested with a difference in height above the ground level. While one has 0:3m, the other rises 0:8m above the ground level. The computer model was calibrated using the experimental results. The pile cap foundation will be programmed in a finite element environment called OpenSees (Open System for Earthquake Engineering Simulation [28]). This environment is a free software developed by Berkeley University specialized, as it name says, in the study of earthquakes and its effects on structures. This specialization is the main reason why it is being used for building this model as it makes it possible to build any finite element model, and perform several analysis in order to get the results wanted. The development of OpenSees is sponsored by the Pacific Earthquake Engineering Research Center through the National Science Foundation engineering and education centers program. OpenSees uses Tcl language to program it, which is a language similar to C++.

Estudio teórico-experimental para la mejora de la resistencia estructural de autocares basado en el diseño de uniones y asientos

La presente tesis analiza la mejora de la resistencia estructural ante vuelco de autocares enfocando dos vías de actuación: análisis y propuestas de requisitos reglamentarios a nivel europeo y la generación de herramientas que ayuden al diseño y a la verificación de estos requisitos. Los requisitos reglamentarios de resistencia estructural a vuelco contemplan la superestructura de los vehículos pero no para los asientos y sistemas de retención. La influencia de los pasajeros retenidos es superior a la incluida en reglamentación (Reg. 66.01) debiendo considerarse unida al vehículo un porcentaje de la masa de los pasajeros del 91% para cinturón de tres puntos y del 52% para cinturón subabdominal frente al 50% reglamentario para todos los casos. Se ha determinado la cinemática y dinámica del vuelco normativo en sus diferentes fases, formulando las energías en las fases iniciales (hasta el impacto contra el suelo) y determinando la fase final de deformación a través del análisis secuencial de ensayos de módulos reales. Se han determinado los esfuerzos para los asientos que se dividen en dos fases diferenciadas temporalmente: una primera debida a la deformación estructural y una segunda debida al esfuerzo del pasajero retenido que se produce en sentido opuesto (con una deceleración del pasajero en torno a 3.3 g). Se ha caracterizado a través de ensayos cuasi.estáticos el comportamiento de perfiles a flexión y de las uniones estructurales de las principales zonas del vehículo (piso, ventana y techo) verificándose la validez del comportamiento plástico teórico Kecman.García para perfiles de hasta 4 mm de espesor y caracterizando la resistencia y rigidez en la zona elástica de las uniones en función del tipo de refuerzo, materiales y perfiles (análisis de más de 180 probetas). Se ha definido un método de ensayo cuasi.estático para asientos ante esfuerzos de vuelco, ensayándose 19 butacas y determinándose que son resistentes (salvo las uniones a vehículo con pinzas), que son capaces de absorber hasta más de un 17% de la energía absorbida, aunque algunos necesitan optimización para llegar a contribuir en el mecanismo de deformación estructural. Se han generado modelos simplificados para introducir en los modelos barra.rótula plástica: un modelo combinado unión+rótula plástica (que incluye la zona de rigidez determinada en función del tipo de unión) para la superestructura y un modelo simplificado de muelles no.lineales para los asientos. Igualmente se ha generado la metodología de diseño a través de ensayos virtuales con modelos de detalle de elementos finitos tanto de las uniones como de los asientos. Se ha propuesto una metodología de diseño basada en obtener el “mecanismo óptimo de deformación estructural” (elevando la zona de deformación lateral a nivel de ventana y en pilar o en costilla en techo). Para ello se abren dos vías: diseño de la superestructura (selección de perfiles y generación de uniones resistentes) o combinación con asientos (que en lugar de solo resistir las cargas pueden llegar a modificar el mecanismo de deformación). Se ha propuesto una metodología de verificación alternativa al vuelco de vehículo completo que contempla el cálculo cuasi.estático con modelos simplificados barra.rótula plástica más el ensayo de una sección representativa con asientos y utillajes antropomórficos retenidos que permite validar el diseño de las uniones, determinar el porcentaje de energía que debe absorberse por deformación estructural (factor C) y verificar el propio asiento como sistema de retención. ABSTRACT This research analyzes the improvement of the structural strength of buses and coaches under rollover from two perspectives: regulatory requirements at European level and generation of tools that will help to the design and to the verification of requirements. European Regulations about rollover structural strength includes requirements for the superstructure of the vehicles but not about seats, anchorages and restraint systems. The influence of the retained passengers is higher than the one included currently in the Regulations (Reg. 66.01), being needed to consider a 91% of the passenger mass as rigidly joint to the vehicle (for 3 points’ belt, a 52% for 2 points’ belt) instead of the 50% included in the Regulation. Kinematic and dynamic of the normative rollover has been determined from testing of different sections, formulating the energies of the first phases (up to the first impact with the ground) and determining the last deformation phase through sequential analysis of movements and deformations. The efforts due to rollover over the seats have been established, being divided in two different temporal phases: a first one due to the structural deformation of the vehicle and a second one due to the effort of the restrained passenger being this second one in opposite sense (with a passenger deceleration around 3.3 g). From quasi.static testing, the behavior of the structural tubes under flexural loads, including the principal joints in the vehicle (floor, window and roof), the validity of the theoretical plastic behavior according Kecman.García theories have been verified up to 4 mm of thickness. Strength of the joints as well as the stiffness of the elastic zone has been determined in function of main parameters: type of reinforcement, materials and section of the tubes (more than 180 test specimens). It has been defined a quasi.static testing methodology to characterize the seats and restrain system behavior under rollover, testing 19 double seats and concluding that they are resistant (excepting clamping joints), that they can absorb more than a 17 of the absorbed energy, and that some of them need optimization to contribute in the structural deformation mechanism. It has been generated simplified MEF models, to analyze in a beam.plastic hinge model: a combined model joint+plastic hinge (including the stiffness depending on the type of joint) for the superstructure and a simplified model with non.lineal springs to represent the seats. It has been detailed methodologies for detailed design of joints and seats from virtual testing (MEF models). A design methodology based in the “optimized structural deformation mechanism” (increasing the height of deformation of the lateral up to window level) is proposed. Two possibilities are analyzed: design of the superstructure based on the selection of profiles and design of strength joints (were seats only resist the efforts and contribute in the energy absorption) or combination structure.seats, were seats contributes in the deformation mechanism. An alternative methodology to the rollover of a vehicle that includes the quasi.static calculation with simplified models “beam.joint+plastic hinge” plus the testing of a representative section of the vehicle including seats and anthropomorphic ballast restrained by the safety belts is presented. The test of the section allows validate the design of the joints, determine the percentage of energy to be absorbed by structural deformation (factor C) and verify the seat as a retention system.

Evapotranspiration of grapevine trained to a gable trellis system under netting and black plastic mulching

The evapotranspiration (ET c) of a table grape vineyard (Vitis vinifera, cv. Red Globe) trained to a gable trellis under netting and black plastic mulching was determined under semiarid conditions in the central Ebro River Valley during 2007 and 2008. The netting was made of high-density polyethylene (pores of 12 mm2) and was placed just above the ground canopy about 2.2 m above soil surface. Black plastic mulching was used to minimize soil evaporation. The surface renewal method was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Later, latent heat flux (LE) values were obtained by solving the energy balance equation. For the May–October period, seasonal ET c was about 843 mm in 2007 and 787 mm in 2008. The experimental weekly crop coefficients (K cexp) fluctuated between 0.64 and 1.2. These values represent crop coefficients adjusted to take into account the reduction in ET c caused by the netting and the black plastic mulching. Average K cexp values during mid- and end-season stages were 0.79 and 0.98, respectively. End-season K cexp was higher due to combination of factors related to the precipitation and low ET o conditions that are typical in this region during fall. Estimated crop coefficients using the Allen et al. (1998) approach adjusting for the effects of the netting and black plastic mulching (K cFAO) showed a good agreement with the experimental K cexp values.

The role of computational logic as a hinge paradigm among deduction, problem solving, programming, and parallelism

This paper presents some brief considerations on the role of Computational Logic in the construction of Artificial Intelligence systems and in programming in general. It does not address how the many problems in AI can be solved but, rather more modestly, tries to point out some advantages of Computational Logic as a tool for the AI scientist in his quest. It addresses the interaction between declarative and procedural views of programs (deduction and action), the impact of the intrinsic limitations of logic, the relationship with other apparently competing computational paradigms, and finally discusses implementation-related issues, such as the efficiency of current implementations and their capability for efficiently exploiting existing and future sequential and parallel hardware. The purpose of the discussion is in no way to present Computational Logic as the unique overall vehicle for the development of intelligent systems (in the firm belief that such a panacea is yet to be found) but rather to stress its strengths in providing reasonable solutions to several aspects of the task.

B.I.E.M.in 3-D elasto-plastic problems

In this paper we present the application of BIEM to elastoplastic axysimetric problems. After a brief presentation of the basic integral formulation we introduce the discretizing and iterative process for its resolution. Simple problems are compared in order to test the possibilities of the method and we finish commenting on future research needs.

Multiscale modeling of the plastic behaviour in single crystal tungsten: from atomistic to crystal plasticity simulations

En una planta de fusión, los materiales en contacto con el plasma así como los materiales de primera pared experimentan condiciones particularmente hostiles al estar expuestos a altos flujos de partículas, neutrones y grandes cargas térmicas. Como consecuencia de estas diferentes y complejas condiciones de trabajo, el estudio, desarrollo y diseño de estos materiales es uno de los más importantes retos que ha surgido en los últimos años para la comunidad científica en el campo de los materiales y la energía. Debido a su baja tasa de erosión, alta resistencia al sputtering, alta conductividad térmica, muy alto punto de fusión y baja retención de tritio, el tungsteno (wolframio) es un importante candidato como material de primera pared y como posible material estructural avanzado en fusión por confinamiento magnético e inercial. Sin embargo, el tiempo de vida del tungsteno viene controlado por diversos factores como son su respuesta termo-mecánica en la superficie, la posibilidad de fusión y el fallo por acumulación de helio. Es por ello que el tiempo de vida limitado por la respuesta mecánica del tungsteno (W), y en particular su fragilidad, sean dos importantes aspectos que tienes que ser investigados. El comportamiento plástico en materiales refractarios con estructura cristalina cúbica centrada en las caras (bcc) como el tungsteno está gobernado por las dislocaciones de tipo tornillo a escala atómica y por conjuntos e interacciones de dislocaciones a escalas más grandes. El modelado de este complejo comportamiento requiere la aplicación de métodos capaces de resolver de forma rigurosa cada una de las escalas. El trabajo que se presenta en esta tesis propone un modelado multiescala que es capaz de dar respuestas ingenieriles a las solicitudes técnicas del tungsteno, y que a su vez está apoyado por la rigurosa física subyacente a extensas simulaciones atomísticas. En primer lugar, las propiedades estáticas y dinámicas de las dislocaciones de tipo tornillo en cinco potenciales interatómicos de tungsteno son comparadas, determinando cuáles de ellos garantizan una mayor fidelidad física y eficiencia computacional. Las grandes tasas de deformación asociadas a las técnicas de dinámica molecular hacen que las funciones de movilidad de las dislocaciones obtenidas no puedan ser utilizadas en los siguientes pasos del modelado multiescala. En este trabajo, proponemos dos métodos alternativos para obtener las funciones de movilidad de las dislocaciones: un modelo Monte Cario cinético y expresiones analíticas. El conjunto de parámetros necesarios para formular el modelo de Monte Cario cinético y la ley de movilidad analítica son calculados atomísticamente. Estos parámetros incluyen, pero no se limitan a: la determinación de las entalpias y energías de formación de las parejas de escalones que forman las dislocaciones, la parametrización de los efectos de no Schmid característicos en materiales bcc,etc. Conociendo la ley de movilidad de las dislocaciones en función del esfuerzo aplicado y la temperatura, se introduce esta relación como ecuación de flujo dentro de un modelo de plasticidad cristalina. La predicción del modelo sobre la dependencia del límite de fluencia con la temperatura es validada experimentalmente con ensayos uniaxiales en tungsteno monocristalino. A continuación, se calcula el límite de fluencia al aplicar ensayos uniaxiales de tensión para un conjunto de orientaciones cristalográticas dentro del triángulo estándar variando la tasa de deformación y la temperatura de los ensayos. Finalmente, y con el objetivo de ser capaces de predecir una respuesta más dúctil del tungsteno para una variedad de estados de carga, se realizan ensayos biaxiales de tensión sobre algunas de las orientaciones cristalográficas ya estudiadas en función de la temperatura.-------------------------------------------------------------------------ABSTRACT ----------------------------------------------------------Tungsten and tungsten alloys are being considered as leading candidates for structural and functional materials in future fusion energy devices. The most attractive properties of tungsten for the design of magnetic and inertial fusion energy reactors are its high melting point, high thermal conductivity, low sputtering yield and low longterm disposal radioactive footprint. However, tungsten also presents a very low fracture toughness, mostly associated with inter-granular failure and bulk plasticity, that limits its applications. As a result of these various and complex conditions of work, the study, development and design of these materials is one of the most important challenges that have emerged in recent years to the scientific community in the field of materials for energy applications. The plastic behavior of body-centered cubic (bcc) refractory metals like tungsten is governed by the kink-pair mediated thermally activated motion of h¿ (\1 11)i screw dislocations on the atomistic scale and by ensembles and interactions of dislocations at larger scales. Modeling this complex behavior requires the application of methods capable of resolving rigorously each relevant scale. The work presented in this thesis proposes a multiscale model approach that gives engineering-level responses to the technical specifications required for the use of tungsten in fusion energy reactors, and it is also supported by the rigorous underlying physics of extensive atomistic simulations. First, the static and dynamic properties of screw dislocations in five interatomic potentials for tungsten are compared, determining which of these ensure greater physical fidelity and computational efficiency. The large strain rates associated with molecular dynamics techniques make the dislocation mobility functions obtained not suitable to be used in the next steps of the multiscale model. Therefore, it is necessary to employ mobility laws obtained from a different method. In this work, we suggest two alternative methods to get the dislocation mobility functions: a kinetic Monte Carlo model and analytical expressions. The set of parameters needed to formulate the kinetic Monte Carlo model and the analytical mobility law are calculated atomistically. These parameters include, but are not limited to: enthalpy and energy barriers of kink-pairs as a function of the stress, width of the kink-pairs, non-Schmid effects ( both twinning-antitwinning asymmetry and non-glide stresses), etc. The function relating dislocation velocity with applied stress and temperature is used as the main source of constitutive information into a dislocation-based crystal plasticity framework. We validate the dependence of the yield strength with the temperature predicted by the model against existing experimental data of tensile tests in singlecrystal tungsten, with excellent agreement between the simulations and the measured data. We then extend the model to a number of crystallographic orientations uniformly distributed in the standard triangle and study the effects of temperature and strain rate. Finally, we perform biaxial tensile tests and provide the yield surface as a function of the temperature for some of the crystallographic orientations explored in the uniaxial tensile tests.

Plastic Furniture: las sillas-mundo

Investigación sobre las herramientas arquitectónicas utilizadas por Charles y Ray Eames a través del estudio de la familia de mobiliario que ha recibido el nombre de Plastic Furniture

Determining the elastic-plastic properties of metallic materials through instrumented indentation

En los últimos años, y asociado al desarrollo de la tecnología MEMS, la técnica de indentación instrumentada se ha convertido en un método de ensayo no destructivo ampliamente utilizado para hallar las características elástico-plásticas de recubrimientos y capas delgadas, desde la escala macroscópica a la microscópica. Sin embargo, debido al complejo mecanismo de contacto debajo de la indentación, es urgente proponer un método más simple y conveniente para obtener unos resultados comparables con otras mediciones tradicionales. En este estudio, el objetivo es mejorar el procedimiento analítico para extraer las propiedades elástico-plásticas del material mediante la técnica de indentación instrumentada. La primera parte se centra en la metodología llevada a cabo para medir las propiedades elásticas de los materiales elásticos, presentándose una nueva metodología de indentación, basada en la evolución de la rigidez de contacto y en la curva fuerza-desplazamiento del ensayo de indentación. El método propuesto permite discriminar los valores de indentación experimental que pudieran estar afectados por el redondeo de la punta del indentador. Además, esta técnica parece ser robusta y permite obtener valores fiables del modulo elástico. La segunda parte se centra en el proceso analítico para determinar la curva tensión-deformación a partir del ensayo de indentación, empleando un indentador esférico. Para poder asemejar la curva tension-deformación de indentación con la que se obtendría de un ensayo de tracción, Tabor determinó empíricamente un factor de constricción de la tensión () y un factor de constricción de la deformación (). Sin embargo, la elección del valor de y  necesitan una derivación analítica. Se describió analíticamente una nueva visión de la relación entre los factores de constricción de tensión y la deformación basado en la deducción de la ecuación de Tabor. Un modelo de elementos finitos y un diseño experimental se realizan para evaluar estos factores de constricción. A partir de los resultados obtenidos, las curvas tension-deformación extraidas de los ensayos de indentación esférica, afectadas por los correspondientes factores de constricción de tension y deformación, se ajustaron a la curva nominal tensión-deformación obtenida de ensayos de tracción convencionales. En la última parte, se estudian las propiedades del revestimiento de cermet Inconel 625-Cr3C2 que es depositado en el medio de una aleación de acero mediante un láser. Las propiedades mecánicas de la matriz de cermet son estudiadas mediante la técnica de indentación instrumentada, haciendo uso de las metodologías propuestas en el presente trabajo. In recent years, along with the development of MEMS technology, instrumented indentation, as one type of a non-destructive measurement technique, is widely used to characterize the elastic and plastic properties of metallic materials from the macro to the micro scale. However, due to the complex contact mechanisms under the indentation tip, it is necessary to propose a more convenient and simple method of instrumented indention to obtain comparable results from other conventional measurements. In this study, the aim is to improve the analytical procedure for extracting the elastic plastic properties of metallic materials by instrumented indentation. The first part focuses on the methodology for measuring the elastic properties of metallic materials. An alternative instrumented indentation methodology is presented. Based on the evolution of the contact stiffness and indentation load versus the depth of penetration, the possibility of obtaining the actual elastic modulus of an elastic-plastic bulk material through instrumented sharp indentation tests has been explored. The proposed methodology allows correcting the effect of the rounding of the indenter tip on the experimental indentation data. Additionally, this technique does not seem too sensitive to the pile-up phenomenon and allows obtaining convincing values of the elastic modulus. In the second part, an analytical procedure is proposed to determine the representative stress-strain curve from the spherical indentation. Tabor has determined the stress constraint factor (stress CF), and strain constraint factor (strain CF), empirically but the choice of a value for and is debatable and lacks analytical derivation. A new insight into the relationship between stress and strain constraint factors is analytically described based on the formulation of Tabor’s equation. Finite element model and experimental tests have been carried out to evaluate these constraint factors. From the results, representative stress-strain curves using the proposed strain constraint factor fit better with the nominal stress-strain curve than those using Tabor’s constraint factors. In the last part, the mechanical properties of an Inconel 625-Cr3C2 cermet coating which is deposited onto a medium alloy steel by laser cladding has been studied. The elastic and plastic mechanical properties of the cermet matrix are studied using depth-sensing indentation (DSI) on the micro scale.

A plastic analysis of nonprismatic folded plate structures

A computer method for the plastic analysis of folded plate structures is presented. The method considers the specific characteristics of the folded plate structural model using a simplified one-dimensional theory. and it can be applied to the analysis of any type of folded pIates, either prismatic or nonprismatic, with arbitrary cross-section. A simple example is analyzed in order to show the possibilities of the procedure and some results of interest are presented

The folded plate model in structural analysis. Elastic, plastic and dynamic formulations for nonprismatic structures

A specific numerical procedure for the analysis of arbitrary nonprismatic folded plate structures is presented. An elastic model is studied and compared with a harmonic solution for a prismatic structure. An extension to the plastic analysis is developed, and the influence of the structural geometry and loading pattern is analyzed. Nonprismatic practical cases, with arbitrary geometry and loading are shown, as well in the elastic range as in the plastic one. Finally, a dynamic formulation is outlined