Accurate Simulation of MPPT Methods Performance When Applied to Commercial Photovoltaic Panels

Anew, simple, and quick-calculationmethodology to obtain a solar panel model, based on the manufacturers’ datasheet, to perform MPPT simulations, is described. The method takes into account variations on the ambient conditions (sun irradiation and solar cells temperature) and allows fast MPPT methods comparison or their performance prediction when applied to a particular solar panel. The feasibility of the described methodology is checked with four different MPPT methods applied to a commercial solar panel, within a day, and under realistic ambient conditions.

Energía fotovoltaica: Trazador de curvas V-1 para seguimiento de módulos solares

Definición, construcción y puesta en marcha de un trazador de Curvas I-V en placas fotovoltaicas con fines docentes, comparándolo con otros métodos de medida. Para lo cual se han realizado diferentes ensayos: Barrido de Curva V-I módulo KC50 Barrido de Curva V-I módulo KC85GX-2P Barrido de Curva V-I con sombreado de células Barrido de Curva V-I con conexión en serie y en paralelo Barrido de Curva V-I sin diodos “by-pass” Barrido de Curva V-I con conexión en serie y en paralelo sin diodos “by-pass” Abstract Definition, construction and startup of a tracer IV curves in photovoltaic panels for teaching purposes, compared to other measurement methods. The trials completed can be summarized as follows: Sweep curve V-I module KC50. Sweep curve V-I module KC85GX-2P Sweep curve V-I with shaded cells. Sweep curve V-I with series and parallel connections. Sweep curve V-I without “by-pass” diode. Sweep curve V-I with series and parallel connections without “by-pass” diodes.

Fiabilidad de minimodulos de silicio

El objetivo de este Proyecto Final de Carrera es la realización de un ensayo de fiabilidad de componentes electrónicos, más concretamente de Minimódulos de Silicio, con el fin de estudiar su comportamiento a lo largo del tiempo de vida. Debido a la larga duración de los Minimódulos de Silicio , un ensayo de este tipo podría durar años, por lo que es necesario realizar un ensayo acelerado que acorte significativamente el tiempo del experimento, para ello, han de someterse a esfuerzos mayores que en condiciones normales de funcionamiento. A día de hoy, los Minimódulos de silicio, que conocemos como placas solares fotovoltaicas, se usan en infinidad de dispositivos debido a las múltiples ventajas que conllevan. La principal ventaja es poder llevar electricidad a cualquier parte del planeta sin necesidad de tener que hacer unas elevadas inversiones. Esta electricidad proviene de una fuente de energía inagotable y nada contaminante, con lo que ayudamos a mantener el equilibrio del planeta. La mayoría de las veces estas placas solares fotovoltaicas se usan en el exterior, soportando cambios de temperatura y de humedad elevados, de ahí, la importancia de realizar ensayos de fiabilidad, que muestren sus posibles causas de fallo, los efectos que producen estos fallos y los aspectos de diseño, fabricación y mantenimiento que puedan afectarles. Los Minimódulos de silicio utilizados en este proyecto son el modelo MC-SP0.8-NF-GCS de la empresa fabricante Multicomp. Para realizar el Proyecto hubiéramos necesitado una cámara climática que simulara unas condiciones ambientales determinadas, pero debido a la dificultad de iluminar el módulo dentro de la cámara climática hemos desarrollado un nuevo sistema de ensayos acelerados en temperatura. El nuevo sistema de ensayos acelerados consiste en: •Colocar los módulos fotovoltaicos en el laboratorio con un foco de 500W que irradia lo equivalente al sol. •Los tres módulos trabajarán a tres temperaturas diferentes para simular condiciones ambientales distintas, concretamente a 60°C, 72°C y 84°C. •Mediante un sistema automático de medida diseñado en LabVIEW, de manera simultánea tomará medidas de tensión en las tres placas y estudiaremos el grado degradación en cada placa. Se analizaran los resultados obtenido de cada una de las medidas y se realizará un estudio de fiabilidad y del proceso de degradación sufrido por los Minimódulos de silicio. Este PFC se puede dividir en las siguientes fases de trabajo siendo el ensayo la parte más larga en el tiempo: •Búsqueda de bibliografía documentación y normas aplicables. •Familiarización con los equipos y software, estudiando el manejo del software que viene con el Multímetro Keithley 2601 y el programa LabVIEW. •Desarrollo del hardware y sistemas necesarios para la realización del ensayo. •Montaje del ensayo •Realización del ensayo. •Análisis de resultados. ABSTRACT. The objective of this Final Project is conducting a test reliability of electronic components, more specifically Silicon minimodules, in order to study their behavior throughout the life span. Due to the long duration of Silicon minimodules a test like this could take years, so it is necessary to perform an accelerated significantly shorten the time of the experiment, testing for it, should be subjected to greater efforts than in normal operating. Today, the mini-modules, silicon is known as photovoltaic solar panels are used in a multitude of devices due to the many advantages they bring. The main advantage is to bring electricity to anywhere in the world without having to make high investments. This electricity comes from an inexhaustible source of energy and no pollution, thus helping to maintain the balance of the planet. Most of the time these solar photovoltaic panels are used on the outside, enduring changes in temperature and high humidity, hence, the importance of reliability testing, showing the possible causes of failure, the effects produced by these faults and aspects of design, manufacturing and maintenance that may affect them. The silicon mini-modules used in this project are the MC-SP0.8-NF-GCS model Multicomp manufacturing company. To realize the project we would have needed a climatic chamber to simulate specific environmental conditions, but due to the difficulty of illuminating the module in the climate chamber we have developed a new system of accelerated tests in temperature. The new system is accelerated tests: •Place the PV modules in the laboratory with a focus on the equivalent 500W radiating sun. •The three modules work at three different temperatures to simulate different environmental conditions, namely at 60 °C, 72 °C and 84 °C. •Automatic measurement system designed in LabVIEW, simultaneous voltage measurements taken at the three plates and study the degradation degree in each plate. The results obtained from each of the measurements and a feasibility study and degradation suffered by the silicon is performed minimodules were analyzed. This PFC can be divided into the following phases of the test work the longest part being overtime: •Literature search and documentation standards. •Familiarization with equipment and software, studying management software that comes with the Keithley 2601 multimeter and the LabVIEW program. •Development of hardware and systems necessary for the conduct of the trial. •Experiment setup •Carrying out the experiment. •Analysis of results.

Criterios técnicos del proyecto con módulos tridimensionales ligeros: las casas del Solar Decathlon 2005 y 2007

Este trabajo se ocupa de la construcción modular ligera de viviendas unifamiliares, más concretamente aborda el problema de la definición constructiva de las mismas, habida cuenta de lo poco conocido y publicado de este aspecto en particular. Dado que la construcción es fruto de la evolución, resulta de gran importancia el estudio de los antecedentes para comprender la situación actual, por ello para documentar como corresponde el estado de la técnica y de la investigación se estudiaron los antecedentes desde sus primeras manifestaciones a finales del siglo XIX hasta nuestros días. Contrariamente a las profecías de Le Corbusier y otros, la industrialización no ha llegado a la construcción ni en la forma ni en la medida que era de esperar a principios del siglo XX. Sin embargo y a pesar del relativo “fracaso” de la industrialización en convertirse en la forma mayoritaria de producir edificios, lo cierto es que algunos sistemas altamente industrializados, como lo es la construcción modular ligera, han logrado un lugar en el mercado, que en algunos países resulta cuanto menos significativo. Delimitar el estado de la técnica y la situación actual es crucial en este trabajo, toda vez que la construcción industrializada la realizan empresas, y situarse al margen de las mismas y de su producción, nos guste o no, resulta contrario al sentido común. De este modo se han identificado y documentado ejemplos como el de EE.UU. y Japón, entre otros, que resultan muy ilustrativos tanto desde la evolución como del estado actual. Del estado de la técnica y la investigación también resulta la escasez de publicación de detalles constructivos específicos de la construcción modular ligera. Es obvio que los fabricantes intentan blindarse mediante el secreto industrial, logrando que las soluciones constructivas más interesantes queden fuertemente protegidas dentro del conocimiento reservado de la empresa. De este modo un sistema que alcanza grados de prefabricación del 95%, tan atractivo e interesante para el arquitecto queda reservado al conocimiento de unos pocos dentro de las empresas. La búsqueda de mayor información sobre estos sistemas encuentra un filón indiscutible en los proyectos de las casas del concurso Solar Decathlon. En efecto, debido a las condiciones particulares de este concurso, las casas que compiten deben ser instaladas en un plazo corto, por lo que en su mayoría recurren al método de construcción modular ligera, para lograr correctamente este objetivo. Adicionalmente todos los planos de proyecto incluidos los de detalle, así como memorias de especificaciones técnicas, quedan colgadas en la Web, a libre disposición del público. De este modo se ha considerado interesante, conveniente y útil, aprovechar como fuente documental de este trabajo, aparte de lo obtenido en el estado de la técnica y la investigación, los proyectos de las casas de los concursos 2005 y 2007, que fueron las dos últimas ediciones celebradas cuando se inició esta tesis. De modo similar a esta carencia de detalles publicados se observa igualmente una falta de investigación y de metodologías adecuadas a la misma sobre soluciones y detalles constructivos propios de la construcción modular ligera. Por eso y ante la dificultad de manejar adecuadamente una información disponible pero farragosa, este trabajo ha dedicado una parte importante de su esfuerzo a la creación de una metodología adecuada a este tipo de situación. Hay que destacar que cada proyecto puede constar fácilmente de 60 a casi 200 planos, sin contar las memorias técnicas y otros documentos, tales como galerías de imágenes, etc. Por otra parte resulta útil establecer esta metodología, no solo para esta tesis, sino para futuros trabajos de investigación sobre el tema, toda vez que con posterioridad a 2007 se han celebrado nuevas ediciones del concurso con su correspondiente volumen de información disponible. La metodología del análisis de los proyectos se basa en el diseño y creación de siete fichas tipo que resumen los aspectos fundamentales del proyecto desde el punto de vista constructivo, permitiendo de este modo su rápida visualización y comprensión sin pretender exhaustividad, ya que en caso de querer profundizar en el detalle de la información siempre está el proyecto original para ello. Tras estudiar la información obtenida de los proyectos de las casas de concurso, se contrastan y discuten los resultados para obtener conocimientos de interés para el objetivo propuesto en la tesis. Se comparan los resultados procedentes del estado de la técnica y de la investigación y se obtienen las conclusiones correspondientes. De este modo ha sido posible identificar una serie de criterios técnicos de proyecto de viviendas unifamiliares realizadas mediante construcción modular ligera, que además se organizan en varios niveles, por lo que el resultado es un conjunto de criterios como germen de una futura guía o manual. Como conclusiones fundamentales de la tesis hay que destacar las metodológicas, que habilitan la extensión de este estudio a otros trabajos y la aportación original al conocimiento con la definición de una serie de criterios técnicos de proyecto de viviendas realizadas mediante construcción modular ligera, que además de mejorar esta parte del saber constructivo serán de gran ayuda a los arquitectos de cara a la reducción de errores, que a menudo derivan en mayores costes y plazos, cuando no directamente al abandono del sistema constructivo. El trabajo de la tesis se estructura en siete capítulos a saber: Capítulo 1: Introducción, donde se explica el tema de la tesis, el objetivo principal, las limitaciones y se aportan algunas definiciones. Capítulo 2: Estado de la técnica y la investigación, dentro del cual se presentan los antecedentes desde sus inicios pasando por la primera y segunda mitad del siglo XX y finalizando con el estado actual que recorre los sistemas de EE.UU, Japón, Europa, Escandinavia, centro Europa, Francia, España y algunos ejemplos de Latinoamérica. En el estado de la investigación se presentan las publicaciones tanto en revistas científicas indexadas en el JCR, como publicaciones no indexadas en las que se muestran artículos científicos, comunicaciones a congresos, documentación sobre el concurso Solar Decathlon, libros específicos y libros genéricos sobre construcción modular ligera, tesis doctorales tanto generales como específicas sobre el concurso Solar Decathlon, documentos de idoneidad técnica, páginas Web del concurso Solar Decathlon y finalmente páginas Web de empresas de construcción modular ligera y patentes. También se expresan las conclusiones parciales del capítulo así también como la justificación y los objetivos particulares. Capítulo 3: Metodología, se expone en primer lugar el planteamiento del problema, para luego desarrollar los métodos utilizados para el estudio y clasificación del transporte y de la organización modular, la relación entre la organización modular y distribución espacial, el diseño y contenido de las fichas resumen de los 38 proyectos presentados al SD2005 y SD2007, así también como la información consultada para su realización. Se explica asimismo como se realizaron las tablas comparativas partiendo de la información de las fichas. Finalmente se expresa la manera en que se trató el estudio particular de la junta entre módulos. Capítulo 4: Discusión de resultados, dónde en primer lugar se presenta la clasificación y las estrategias del transporte así también como una clasificación de la organización modular, en segundo lugar se estudian las relaciones que existen entre el sistema modular y la organización espacial. A partir de aquí se muestra el estudio de la estructura de todas las casas del SD2005 y SD2007, según el tipo y material de las zapatas, mostrando tanto tablas cuantitativas como tablas gráficas con fotos. De la misma manera se tratan los forjados, los pilares y las vigas y las cubiertas. Se estudia además el cerramiento opaco y acristalado, la cubierta y el forjado según las capas que lo componen. En el caso de las instalaciones se estudian las que son especiales, descartando las normales en este tipo de casas, como son los paneles fotovoltaicos, placas térmicas o tubos de vacío y los sistemas de almacenamiento de energía, como las baterías, presentando tablas numéricas y gráficas con fotos. El transporte se analiza según corresponda al traslado de la vivienda o al transporte de apoyo, según el tipo y la cantidad utilizado. Con respecto al montaje se diferencia en si se usó grúa o no, y en el caso de no utilizarse se muestran los métodos alternativos. Con respecto a la exploración de la organización modular se presentan la cantidad de módulos que utilizó cada casa, así como también la cuantificación de los sistemas híbridos como son elementos lineales 1D, paneles 2D. Por último se muestra el estudio detallado de la junta entre módulos 3D. Finalmente se realiza la propuesta de un conjunto de criterios técnicos de proyecto organizado en cuatro niveles: 1º nivel de criterios generales, 2º nivel sobre sistemas constructivos, 3º nivel de detalles constructivos y el 4º nivel llamado logística obras previas, transporte y montaje. Capítulo 5: Conclusiones y líneas futuras de investigación, se exponen las conclusiones generales, metodológicas, documentales y por último las de construcción modular. Finalmente se realiza una propuesta de líneas futuras de investigación. Capítulo 6: Bibliografía. Capítulo 7: Anexos, en el que se presentan todas las fichas resumen de las casas realizadas por el autor de esta tesis. Además se incluyen los casos concretos de Voisin en Francia y la TVA (Tennessee Valley Authority) en EE.UU., así como referencias de manuales genéricos de construcción ligera, medidas de transporte en España e información sobre estadísticas de viviendas en la Unión Europea. ABSTRACT This paper deals with Light Modular Construction of houses, and specifically addresses the problem of the constructive definition of the same, given how little known and published this subject has been. Since building construction is the result of evolution, it is of great importance to study its background for understanding the current situation, therefore to document the state of the art and research, its history was studied from its origins dating to the end nineteenth century to our days. Contrary to the prophecies of Le Corbusier and others, industrialization has not reached the construction neither in the form nor to the extent that it was expected in the early twentieth century. However, despite the relative "failure" of industrialization to become the major form of production for buildings, the fact is that some highly industrialized systems, such as the so called Lightweight Modular Construction, have achieved a place in the market, which in some countries is at least significant. To outline the state of the art and the current situation is crucial in this work, since industrialized construction is carried out by companies, and to step away from them and their production, whether we like it or not, it is contrary to common sense. So that, several cases have been identified and documented, such as the US and Japan examples, among others, which are very illustrative both from evolution and the current status. The state of the art and research shows also a shortage of publication of specific construction details of light modular construction. Obviously, manufacturers try to shield themselves by trade secret, making the most interesting constructive solutions remain heavily protected within the reserved knowledge of the company, so a system that reaches levels of 95% prefabrication, so attractive and interesting for the architect It is reserved to the knowledge of a few people inside the companies. The search for more information on these systems finds an invaluable reef in the projects of the Solar Decathlon houses. Indeed, due to the particular conditions of this contest, houses competing must be installed in a short time, so mostly turn to modular construction methods for this purpose to achieve properly this goal. Additionally all levels of project, including detailed and technical specifications reports are published on the Web, freely available to the general public. Thus it was considered interesting, convenient and useful to take advantage as a documentary source of this work, apart from what it were obtained in the state of the art and research, the projects of the houses of the 2005 and 2007 contests, which were the last two editions already held before this thesis was started. Similar to this lack of published details it is also observed a lack of research and methodologies adapted to the solutions and construction details of lightweight modular construction. So that, and facing the difficulty of adequately manage the available but bulky information, this work has devoted a significant part of its effort to create an appropriate methodology for this type of situation. It is noteworthy that each project can easily consist of 60 to almost 200 blueprints, not including technical reports and other documents, such as photo galleries, etc. The methodology of the analysis of the projects is based on the design and creation of seven record sheets that summarize key aspects of the project from a construction point of view, thus allowing quick watching and understanding of the project, without claiming completeness, always keeping for further information the blueprints themselves. After studying the information obtained from the projects of the competition houses, the results are compared and discussed to obtain relevant knowledge according to the objective proposed in the thesis. The results from the state of the art and research are also compared and the conclusions so obtained make possible to identify a number of technical design criteria for single family homes made using lightweight modular construction, which also have been organized at various levels, so the result is a set of criteria as a seed for a future guide or manual. Among the main conclusions of the thesis must be noted the methodological ones, that enable the extension of this study to other works and are an original contribution to knowledge with the definition of a number of technical criteria for housing projects made by light modular construction, what in addition to improving this part of the constructive knowledge will be of great help for the architects to reduce errors that often result in higher costs and delays, if not in abandonment of the construction system itself. The work of the thesis is divided into seven chapters as follows: Chapter 1: Introduction, where the topic of the thesis, the main objective, limitations and the provided definitions is explained. Chapter 2: State of the art and research, within which history is presented from the beginning through the first and second half of the twentieth century and ending with the current systems, that spans from the USA to Japan, Europe, Scandinavia, Central Europe, France, Spain and some Latin American examples. In the state of research publications are presented both on scientific journals indexed in the JCR, and non-indexed publications in which scientific articles, conference papers, information about the Solar Decathlon competition, generic and specific books on light modular construction, articles both general and specific on the Solar Decathlon competition, technical approval documents, dissertations, the Solar Decathlon Web pages and finally lightweight modular construction companies Web pages and patents. The partial conclusions of the chapter as well as the rationale and specific objectives are also expressed. Chapter 3: Methodology first of all exposes the problem statement and then develops the methods used for the study and classification of transportation and modular organization, the relationship between the modular organization and spatial distribution, design and content summary records of the 38 projects submitted to the SD2005 and SD2007, as well as information consulted for its realization. It explains equally how the comparative tables based on information from the chips were made. Finally, the way the particular study of the joint between modules is carried out is also treated. Chapter 4: Discussion, first sorting a classification of transport strategies as well as of modular organization, secondly the relationship between the modular system and the spatial organization studied is presented. From then on, the study of the structure of every house Moreover, to establish this methodology is useful not only for this thesis, but for future research on the subject, since after 2007 there have been held new editions of the contest with a corresponding volume of information available. shown in the SD2005 and SD2007 contests, depending on the type and material of the shoe, showing both quantitative tables as graphic boards with pictures is carried out. Similarly slabs, columns and beams and roofs are treated. Furthermore, the opaque and transparent façades, as well as roof and floor enclosure, according to the layers that compose them are studied. In the case of facilities there have been only addressed that which are of a special type, discarding that considered usual in this type of houses such as photovoltaic panels, thermal panels or vacuum tubes and energy storage systems such as batteries, presenting numerical and graphical tables with photos .The transportation is analyzed depending on it is used to move the house or for additional support, depending on the type and quantity of items used. Regarding assembly it has been made a difference if crane is or not used and if not, what the alternative methods are. With respect to the exploration of the modular organization, the amount of modules used in each house is presented, as well as the quantification of hybrid systems such as linear members as well as 1D, 2D panels. Finally, it has been carried out the detailed study of the joint between 3D modules. Finally it is proposed a set of technical criteria organized into four levels, 1st level of general criteria, 2nd level on building systems, 3rd level construction details and 4th level called previous works and logistics, transportation and assembly. Chapter 5: Conclusions and future research, where general, methodological, documentary and finally modular construction findings are presented. A proposal for further research is done. Chapter 6: Bibliography. Chapter 7: Annexes, in which all the record sheets of houses made by the author of this thesis are presented. Besides the specific cases of Voisin in France and TVA (Tennessee Valley Authority) in the USA, as well as general reference manuals on lightweight construction, transportation dimensions in Spain, and information on housing statistics in the European Union are included.

Review and Comparison of Step-Up Transformerless Topologies for Photovoltaic AC-Module Application

This paper presents a comprehensive review of stepup single-phase non-isolated inverters suitable for ac-module applications. In order to compare the most feasible solutions of the reviewed topologies, a benchmark is set. This benchmark is based on a typical ac-module application considering the requirements for the solar panels and the grid. The selected solutions are designed and simulated complying with the benchmark obtaining passive and semiconductor components ratings in order to perform a comparison in terms of size and cost. A discussion of the analyzed topologies regarding the obtained ratings as well as ground currents is presented. Recommendations for topological solutions complying with the application benchmark are provided.

New method for analytical photovoltaic parameters identification: meeting manufacturer’s datasheet for different ambient conditions

At present, photovoltaic energy is one of the most important renewable energy sources. The demand for solar panels has been continuously growing, both in the industrial electric sector and in the private sector. In both cases the analysis of the solar panel efficiency is extremely important in order to maximize the energy production. In order to have a more efficient photovoltaic system, the most accurate understanding of this system is required. However, in most of the cases the only information available in this matter is reduced, the experimental testing of the photovoltaic device being out of consideration, normally for budget reasons. Several methods, normally based on an equivalent circuit model, have been developed to extract the I-V curve of a photovoltaic device from the small amount of data provided by the manufacturer. The aim of this paper is to present a fast, easy, and accurate analytical method, developed to calculate the equivalent circuit parameters of a solar panel from the only data that manufacturers usually provide. The calculated circuit accurately reproduces the solar panel behavior, that is, the I-V curve. This fact being extremely important for practical reasons such as selecting the best solar panel in the market for a particular purpose, or maximize the energy extraction with MPPT (Maximum Peak Power Tracking) methods.

New method for analytical photovoltaic parameter extraction

Correct modeling of the equivalent circuits regarding solar cell and panels is today an essential tool for power optimization. However, the parameter extraction of those circuits is still a quite difficult task that normally requires both experimental data and calculation procedures, generally not available to the normal user. This paper presents a new analytical method that easily calculates the equivalent circuit parameters from the data that manufacturers usually provide. The analytical approximation is based on a new methodology, since methods developed until now to obtain the aforementioned equivalent circuit parameters from manufacturer's data have always been numerical or heuristic. Results from the present method are as accurate as the ones resulting from other more complex (numerical) existing methods in terms of calculation process and resources.

Near-field light focusing by wavelength-sized dielectric spheroids for photovoltaic applications

We explore the near-field concentration properties of dielectric spheroidal scatterers with sizes close to the wavelength, using an analytical separation-of-variables method. Such particles act as mesoscopic lenses whose physical parameters are optimized here for maximum scattered light enhancement in photovoltaic applications.

Thermodynamics of zinc insertion in CuGaS2:Ti, used as a modulator agent in an intermediate-band photovoltaic material

An intermediate-bandphotovoltaicmaterial, which has an isolated metallic band located between the top of the valence band and bottom of the conduction band of some semiconductors, has been proposed as third generation solar cell to be used in photovoltaic applications. Density functional theory calculations of Zn in CuGaS2:Ti have previously shown that, the intermediate-band position can be modulated in proportion of Zn insertion in such a way that increasing Zn concentration can lead to aband-gap reduction, and an adjustment of the intermediate-band position. This could be interesting in the formation of an intermediate-bandmaterial, that has the maximum efficiency theoretically predicted for the intermediate-band solar cell. In this work, the energetics of several reaction schemes that could lead to the decomposition of the modulated intermediate-bandphotovoltaicmaterial, CuGaS2:Ti:Zn, is studied in order to assess the thermodynamic stability of this material. Calculations of the total free energy and disorder entropy have been taken into account, to get the reaction energy and free energy of the compound decomposition, which is found to be thermodynamically favorable

Análisis de envejecimiento en paneles sándwich de madera/ Ageing tests study on wood-based sandwich panels

Los paneles sándwich de madera son un producto de creciente aplicación en la edificación de nuestro país. Este ascendente uso del material debe estar acompañado de las garantías necesarias avaladas por un estudio previo de sus prestaciones. Como es preceptivo y entre otros, se evalúa su durabilidad frente a las condiciones climatológicas, clave en los productos derivados de la madera, acorde a la normativa actual definida con tal fin, la Guía ETAG 016. Sin embargo, debido a la clase de uso del material, se ha detectado que dicha normativa tal y como está concebida no es capaz de valorar su envejecimiento adecuadamente. En este trabajo se proponen ensayos alternativos al establecido tras exhaustivos aná- lisis que recrean las condiciones reales de uso y más acordes a los productos de madera. Se concluye que la incorporación de una lámina impermeable, pero permeable al vapor de agua hacia el exterior, como las utilizadas en el montaje, aportan el mejor procedimiento de ensayo. Composite lightweight wood panels are being increasingly used in construction in Spain. Their growing use should be accompanied by necessary guarantees based on studies of their properties. As it is prescriptive and in addition to others tests, in the present work is examinated the durability of these panels when exposed to the climatic conditions, a characteristic of great importance for wood products, according to Guide ETAG 016, the current standard defining the ageing tests to be used. However, due to the use class of this material, there are indications that the testing outlined in this Guide is inappropriate for assessing the ageing of wood-based sandwich panels. Alternative tests are here proposed that recreate rather better the real conditions under which these products are used. Covering the samples in a waterproof sheeting permeable to the outward movement of water vapour, which is in fact used in the installation, provided the best procedure for testing these panels.

Failure and impact behavior of facade panels made of glass fiber reinforced cement(GRC)

GRC is a cementitious composite material made up of a cement mortar matrix and chopped glass fibers. Due to its outstanding mechanical properties, GRC has been widely used to produce cladding panels and some civil engineering elements. Impact failure of cladding panels made of GRC may occur during production if some tool falls onto the panel, due to stone or other objects impacting at low velocities or caused by debris projected after a blast. Impact failure of a front panel of a building may have not only an important economic value but also human lives may be at risk if broken pieces of the panel fall from the building to the pavement. Therefore, knowing GRC impact strength is necessary to prevent economic costs and putting human lives at risk. One-stage light gas gun is an impact test machine capable of testing different materials subjected to impact loads. An experimental program was carried out, testing GRC samples of five different formulations, commonly used in building industry. Steel spheres were shot at different velocities on square GRC samples. The residual velocity of the projectiles was obtained both using a high speed camera with multiframe exposure and measuring the projectile’s penetration depth in molding clay blocks. Tests were performed on young and artificially aged GRC samples to compare GRC’s behavior when subjected to high strain rates. Numerical simulations using a hydrocode were made to analyze which parameters are most important during an impact event. GRC impact strength was obtained from test results. Also, GRC’s embrittlement, caused by GRC aging, has no influence on GRC impact behavior due to the small size of the projectile. Also, glass fibers used in GRC production only maintain GRC panels’ integrity but have no influence on GRC’s impact strength. Numerical models have reproduced accurately impact tests.

High-efficiency Köhler photovoltaic concentrators with external light confinement

Metal grid lines are a vital element in multijunction solar cells in order to take out from the cell the generated photocurrent. Nevertheless all this implies certain shadowing factor and thus certain reflectivity on cells surface that lowers its light absorption. This reflectivity produces a loss in electrical efficiency and thus a loss in global energy production for CPV systems. We present here an optical design for recovering this portion of reflected light, and thus leading to a system efficiency increase. This new design is based on an external confinement cavity, an optical element able to redirect the light reflected by the cell towards its surface again. It has been possible thanks to the recent invention of the advanced Köhler concentrators by LPI, likely to integrate one of these cavities easily. We have proven the excellent performance of these cavities integrated in this kind of CPV modules offering outstanding results: 33.2% module electrical efficiency @Tcell=25ºC and relative efficiency and Isc gains of over 6%.

Assessing the solar irradiation potential for solar photovoltaic applications in buildings at low latitudes ¿ Making the case for Brazil

In Brazil, a low-latitude country characterized by its high availability and uniformity of solar radiation, the use of PV solar energy integrated in buildings is still incipient. However, at the moment there are several initiatives which give some hints that lead to think that there will be a change shortly. In countries where this technology is already a daily reality, such as Germany, Japan or Spain, the recommendations and basic criteria to avoid losses due to orientation and tilt are widespread. Extrapolating those measures used in high latitudes to all regions, without a previous deeper analysis, is standard practice. They do not always correspond to reality, what frequently leads to false assumptions and may become an obstacle in a country which is taking the first step in this area. In this paper, the solar potential yield for different surfaces in Brazilian cities (located at latitudes between 0° and 30°S) are analyzed with the aim of providing the necessary tools to evaluate the suitability of the buildings’ envelopes for photovoltaic use

Water harvesting for young trees using Peltier plates powered by photovoltaic solar energy

Young trees transplanted from nursery into open field require a minimum amount of soil moisture to successfully root in their new location, especially in dry-climate areas. One possibility is to obtain the required water from air moisture. This can be achieved by reducing the temperature of a surface below the air dew point temperature, inducing water vapor condensation on the surface. The temperature of a surface can be reduced by applying the thermoelectric effect, with Peltier modules powered by electricity. Here, we present a system that generates electricity with a solar photovoltaic module, stores it in a battery, and finally, it uses the electricity at the moment in which air humidity and temperature are optima to maximize water condensation while minimizing energy consumption. Also, a method to reduce the evaporation of the condensed water is proposed. The objective of the system, rather than irrigating young plants in such a degree as to boost their growth, is to maintain them alive in the dryer periods.

Development of low cost photovoltaic sensor for over-tree radiation assessment

The crop diseases sometimes are related to the irradiance that the crop receives. When an experiment requires the measurement of the irradiance, usually it results in an expensive data acquisition system. If it is necessary to check many test points, the use of traditional sensors will increase the cost of the experiment. By using low cost sensors based in the photovoltaic effect, it is possible to perform a precise test of irradiance with a reduced price. This work presents an experiment performed in Ademuz (Valencia, Spain) during September of 2011 to check the validity of low cost sensors based on solar cells.