V-substituted In2S3: an intermediate band material with photocatalytic activity in the whole visible light range

We proposed in our previous work V-substituted In2S3 as an intermediate band (IB) material able to enhance the efficiency of photovoltaic cells by combining two photons to achieve a higher energy electron excitation, much like natural photosynthesis. Here this hyper-doped material is tested in a photocatalytic reaction using wavelength-controlled light. The results evidence its ability to use photons with wavelengths of up to 750 nm, i.e. with energy significantly lower than the bandgap (=2.0 eV) of non-substituted In2S3, driving with them the photocatalytic reaction at rates comparable to those of non-substituted In2S3 in its photoactivity range (λ ≤ 650 nm). Photoluminescence spectra evidence that the same bandgap excitation as in V-free In2S3 occurs in V-substituted In2S3 upon illumination with photons in the same sub-bandgap energy range which is effective in photocatalysis, and its linear dependence on light intensity proves that this is not due to a nonlinear optical property. This evidences for the first time that a two-photon process can be active in photocatalysis in a single-phase material. Quantum calculations using GW-type many-body perturbation theory suggest that the new band introduced in the In2S3 gap by V insertion is located closer to the conduction band than to the valence band, so that hot carriers produced by the two-photon process would be of electron type; they also show that the absorption coefficients of both transitions involving the IB are of significant and similar magnitude. The results imply that V-substituted In2S3, besides being photocatalytically active in the whole visible light range (a property which could be used for the production of solar fuels), could make possible photovoltaic cells of improved efficiency.

Sol-gel TiO2 nanoparticles prompt photocatalytic cement for pollution degradation

TiO2 nanoparticles (TiO2NPs) prepared by the sol–gel method have been incorporated to cement paste with the aim of creating a photocatalytic system capable of compensating, through degradation of hazardous molecules, the envi- ronmental impact associated to the production of the clinker. Doping was carried out at different mass ratios with TiO2NPs precursor solutions within a fresh ce- ment paste, which was then characterized using scanning electron microscopy (SEM). The photocatalytic performance was evaluated by the degradation of Methylene Blue (MB) using a 125W UV lamp as irradiating source. Main cement properties such as hydration degree and C-S-H content are affected by TiO2NPs doping level. Cement containing TiO2NPs exhibited an increasing photocatalytic activity for increasing doping, while the pure cement paste control could hardly degrade MB. The kinetics of the system where also studied and their second order behavior related to microstructural aspects of the system.

Estudio de las formas de aplicación de la fotografía sobre los materiales pétreos para la arquitectura = Study of photography application methods over architectural stony materials

Desde que el Hombre era morador de las cavernas ha sido manifiesto su deseo innato por grabar y reproducir "instantáneas con las que perpetuarse o sobre las que mirarse ". La aparición y desarrollo de la fotografía como medio para poder captar y fijar "la imagen directa de la realidad circundante " pronto se convierte en un nuevo lenguaje estético y poético que permite al artista la interpretación y reflexión de lo observado. Se imprime a la imagen el carácter de la mirada del fotógrafo, estableciendo un diálogo conceptual con el juego de luces. La presente Tesis plantea la creación de una nueva piel de arquitectura mediante la impresión fotográfica sobre materiales pétreos. La búsqueda de la expresividad de los materiales como soporte de expresión artística implica un cambio de escala al trasladar la instantánea fotográfica a la arquitectura y la aplicación de un nuevo soporte al imprimir la fotografía sobre materiales arquitectónicos. Se justifica la elección del dispositivo láser CO2 como sistema de impresión fotográfica sobre los materiales pétreos arquitectónicos, como la técnica que permite la unión física de la imagen y el proyecto arquitectónico, generando un valor añadido a través del arte de la fotografía. Se justifica la elección de los materiales investigados, Silestone® Blanco Zeus y GRC® con TX Active® Aria, de forma que la investigación de esta nueva piel de arquitectura abarca tanto la envolvente del edificio como su volumen interior, permitiendo cerrar el círculo arquitectónico "in&out" y dota al proyecto arquitectónico de un valor añadido al introducir conceptos sostenibles de carácter estético y medioambiental. Se realiza una consulta a las empresas del sector arquitectónico relacionadas directamente con la producción y distribución de los materiales Silestone® y GRC®, así como a las empresas especializadas en sistemas de impresión fotográfica sobre materiales, acerca del estado del arte. Se recorre la Historia de la fotografía desde sus orígenes hasta el desarrollo de la era digital y se analiza su condición artística. Se recopilan los sistemas de impresión fotográfica que han evolucionado en paralelo con los dispositivos de captura de la instantánea fotográfica y se describe en profundidad el sistema de impresión fotográfica mediante dispositivo láser CO2. Se describen los procesos de fabricación, las características técnicas, cualidades y aplicaciones de los materiales pétreos arquitectónicos Silestone® Blanco Zeus y GRC® con TX Active® Aria. Se explica la técnica utilizada para la captación de la imagen fotográfica, su justificación artística y su proceso de impresión mediante dispositivo láser CO2 bajo diferentes parámetros sobre muestras de los materiales arquitectónicos investigados. Se comprueba la viabilidad de desarrollo de la nueva piel de arquitectura sobre Silestone® Blanco Zeus y GRC® con TX Active® Aria sometiendo a las piezas impresas bajo diferentes parámetros a tres ensayos de laboratorio. En cada uno de ellos se concreta el objetivo y procedimiento del ensayo, la enumeración de las muestras ensayadas y los parámetros bajo los que han sido impresas, el análisis de los resultados del ensayo y las conclusiones del ensayo. Ensayo de amplitud térmica. Se determina el grado de afectación de las imágenes impresas bajo la acción de contrastes térmicos. Series de muestras de Silestone® Blanco Zeus y GRC® con TX Active® Aria impresas con láser CO2 se someten a ciclos de contraste frío-calor de 12 horas de duración para una amplitud térmica total de 102°C. Se realiza una toma sistemática de fotografías microscópicas con lupa de aumento de cada pieza antes y después de los ciclos frío-calor y la observación de las transformaciones que experimentan los materiales bajo la acción del láser CO2. Ensayo de exposición a la acción de la radiación ultravioleta (UV). Se determina el grado de afectación de las imágenes impresas al activar la capacidad autolimpiante de partículas orgánicas. Una serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a ciclos de exposición de radiación ultravioleta de 26 horas de duración. Se somete la serie a un procedimiento de activación del aditivo TX Active®. Se simula la contaminación orgánica mediante la aplicación controlada de Rodamina B, tinte orgánico, y se simula la radiación UV mediante el empleo de una bombilla de emisión de rayos ultravioleta. Se realiza una toma sistemática de fotografías macroscópicas de la serie de muestras ensayadas: antes de aplicación de la Rodamina B, momento 00:00h, momento 04:00h y momento 26:00h del ensayo. Se procede a la descarga y análisis del histograma de las fotografías como registro de la actividad fotocatalítica. Ensayo de la capacidad autodescontaminante del GRC® con TX Active® impreso con láser CO2. Se comprueba si la capacidad autodescontaminante del GRC® con TX Active® se ve alterada como consecuencia de la impresión de la imagen fotográfica impresa con láser CO2. Serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a test de capacidad autodescontaminante: atmósfera controlada y contaminada con óxidos de nitrógeno en los que se coloca cada pieza ensayada bajo la acción de una lámpara de emisión de radiación ultravioleta (UV). Se registra la actividad fotocatalítica en base a la variación de concentración de óxido de nitrógeno. Se recopila el análisis e interpretación de los resultados de los ensayos de laboratorio y se elaboran las conclusiones generales de la investigación. Se sintetizan las futuras líneas de investigación que, a partir de las investigaciones realizadas y de sus conclusiones generales, podrían desarrollarse en el ámbito de la impresión fotográfica sobre materiales arquitectónicos. Se describe el rendimiento tecnológico y artístico generado por las investigaciones previas que han dado origen y desarrollo a la Tesis Doctoral. ABSTRACT Since ancient time, humanity has been driven by an innate wish to reproduce and engrave "snapshots that could help to perpetúate or to look at one self". Photography's birth and its development as a mean to capture and fix "the direct image of the surrounding reality" quickly becomes a new aesthetical and poetical language allowing the artist to interpret and think over what has been observed. The photographer's eye is imprinted onto the image, and so the conceptual dialogue between the artist and the light beams begins. The current thesis suggests the creation of a new architectural skin through photography imprinting over stony materials. The search for material's expressiveness as a medium of artistic expression involves a change of scale as it transfers photographic snapshot into architecture and the use of a new photographic printing support over architectural materials. CO2 laser is the chosen printing system for this technique as it allows the physical union of the image and the architectonic project, generating an added value through the art of photography. The researched materials selected were Silestone®, Blanco Zeus and GRC® with TX Active® Aria. This new architectural skin contains the building surrounding as well as its interior volume, closing the architectonic "in & out" circle and adding a value to the project by introducing aesthetical and environmental sustainable concepts. Architecture companies related to the production and distribution of materials like Silestone® and GRC®, as well as companies specialized in photography printing over materials were consulted to obtain a State of the Art. A thorough analysis of photography's History from its origins to the digital era development was made and its artistic condition was studied in this thesis. In this study the author also makes a compilation of several photographic printing systems that evolved together with photographic snapshot devices. The CO2 laser-based photographic printing system is also described in depth. Regarding stony materials of architecture like Silestone®, Blanco Zeus and GRC® with TX Active® Aria, the present study also describes their manufacture processes as well as technical features, quality and application. There is also an explanation about the technique to capture the photographic image, its artistic justification and its CO2 laser-based printing system over the researched materials under different parameters. We also tested the feasibility of this new architectural skin over Silestone® Blanco Zeus and GRC® with TX Active® Aria. The pieces were tested under different parameters in three laboratory trials. Each trial comprises of an explanation of its objective and its process, the samples were numbered and the printing parameters were specified. Finally, with the analysis of the results some conclusions were drawn. In the thermal amplitude trial we tried to determine how printed images were affected as a result of the action of thermal contrasts. Series of samples of Silestone® Blanco Zeus and GRC® with TX Active® Aria printed with CO2 laser were subjected to several 12h warm-cold cycles for thermal total amplitude of 102oc. Each sample was captured systematically with microscopic enhanced lenses before and after cold-warm cycles. The changes experienced by these materials under the effect of CO2 laser were observed and recorded. Trial regarding the Ultraviolet Radiation (UR) effect on images. We determined to which extent printed images were affected once the self-cleaning organic particles were activated. This time GRC® with TX Active® Aria samples printed with CO2 laser were exposed to a 26h UR cycle. The samples were subjected to the activation of TX Active® additive. Through the controlled application of Rodamine B and organic dye we were able to simulate the organic contamination process. UR was simulated using an ultraviolet beam emission bulb. A systematic capture of macroscopic pictures of the tested sample series was performed at different time points: before Rodamine B application, at moment 00:00h, moment 04:00h and moment 26:00h of the trial. Picture's histogram was downloaded and analyzed as a log of photocatalytic activity. Trial regarding the self-decontaminating ability of GRC® with TX Active® printed with CO2 laser. We tested if this self-decontaminating ability is altered as a result of CO2 laser printed image. GRC® with TX Active® Aria samples printed with CO2 laser, were subject to self-decontaminating ability tests with controlled and nitrogen oxide contaminated atmosphere. Each piece was put under the action of an UR emission lamp. Photocatalytic activity was recorded according to the variation in nitrogen oxide concentration. The results of the trial and their interpretation as well as the general conclusions of the research are also compiled in the present study. Study conclusions enable to draw future research lines of potential applications of photographic printing over architecture materials. Previous research generated an artistic and technological outcome that led to the development of this doctoral thesis.

Inmovilización de TiO2 sobre polímeros transparentes en el UV-A para la eliminación fotocatalítica de tricloroetileno en aire

El gran desarrollo industrial y demográfico de las últimas décadas ha dado lugar a un consumo crecientemente insostenible de energía y materias primas, que influye negativamente en el ambiente por la gran cantidad de contaminantes generados. Entre las emisiones tienen gran importancia los compuestos orgánicos volátiles (COV), y entre ellos los compuestos halogenados como el tricloroetileno, debido a su elevada toxicidad y resistencia a la degradación. Las tecnologías generalmente empleadas para la degradación de estos compuestos presentan inconvenientes derivados de la generación de productos tóxicos intermedios o su elevado coste. Dentro de los procesos avanzados de oxidación (Advanced Oxidation Processes AOP), la fotocatálisis resulta una técnica atractiva e innovadora de interés creciente en su aplicación para la eliminación de multitud de compuestos orgánicos e inorgánicos, y se ha revelado como una tecnología efectiva en la eliminación de compuestos orgánicos volátiles clorados como el tricloroetileno. Además, al poder aprovechar la luz solar como fuente de radiación UV permite una reducción significativa de costes energéticos y de operación. Los semiconductores más adecuados para su empleo como fotocatalizadores con aprovechamiento de la luz solar son aquellos que tienen una banda de energía comparable a la de los fotones de luz visible o, en su defecto, de luz ultravioleta A (Eg < 3,5 eV), siendo el más empleado el dióxido de titanio (TiO2). El objetivo principal de este trabajo es el estudio de polímeros orgánicos comerciales como soporte para el TiO2 en fotocatálisis heterogénea y su ensayo para la eliminación de tricloroetileno en aire. Para ello, se han evaluado sus propiedades ópticas y su resistencia a la fotodegradación, y se ha optimizado la fijación del fotocatalizador para conseguir un recubrimiento homogéneo, duradero y con elevada actividad fotocatalítica en diversas condiciones de operación. Los materiales plásticos ensayados fueron el polietileno (PE), copolímero de etil vinil acetato con distintos aditivos (EVA, EVA-H y EVA-SH), polipropileno (PP), polimetil (metacrilato) fabricado en colada y extrusión (PMMA-C y PMMA-E), policarbonato compacto y celular (PC-C y PC-Ce), polivinilo rígido y flexible (PVC-R y PVC-F), poliestireno (PS) y poliésteres (PET y PETG). En base a sus propiedades ópticas se seleccionaron el PP, PS, PMMA-C, EVA-SH y PVC-R, los cuales mostraron un valor de transmitancia superior al 80% en el entorno de la región estudiada (λ=365nm). Para la síntesis del fotocatalizador se empleó la tecnología sol-gel y la impregnación multicapa de los polímeros seleccionados por el método de dip-coating con secado intermedio a temperaturas moderadas. Con el fin de evaluar el envejecimiento de los polímeros bajo la radiación UV, y el efecto sobre éste del recubrimiento fotoactivo, se realizó un estudio en una cámara de exposición a la luz solar durante 150 días, evaluándose la resistencia química y la resistencia mecánica. Los resultados de espectroscopía infrarroja y del test de tracción tras el envejecimiento revelaron una mayor resistencia del PMMA y una degradación mayor en el PS, PVC-R y EVA SH, con una apreciable pérdida del recubrimiento en todos los polímeros. Los fotocatalizadores preparados sobre soportes sin tratamiento y con tres capas de óxido de titanio mostraron mejores resultados de actividad con PMMA-C, PET y PS, con buenos resultados de mineralización. Para conseguir una mayor y mejor fijación de la película al soporte se realizaron tratamientos químicos abrasivos con H2SO4 y NaOH y tratamientos de funcionalización superficial por tecnología de plasma a presión atmosférica (APP) y a baja presión (LPP). Con los tratamientos de plasma se consiguió una excelente mojabilidad de los soportes, que dio lugar a una distribución uniforme y más abundante del fotocatalizador, mientras que con los tratamientos químicos no se obtuvo una mejora significativa. Asimismo, se prepararon fotocatalizadores con una capa previa de dióxido de silicio con la intervención de surfactantes (PDDA-SiO2-3TiO2 y SiO2FC-3TiO2), consiguiéndose buenas propiedades de la película en todos los casos. Los mejores resultados de actividad con tratamiento LPP y tres capas de TiO2 se lograron con PMMA-C (91% de conversión a 30 ppm de TCE y caudal 200 ml·min-1) mejorando significativamente también la actividad fotocatalítica en PVC-R y PS. Sin embargo, el material más activo de todos los ensayados fue el PMMA-C con el recubrimiento SiO2FC-3TiO2, logrando el mejor grado de mineralización, del 45%, y una velocidad de 1,89 x 10-6 mol· m-2 · s-1, que dio lugar a la eliminación del 100 % del tricloroetileno en las condiciones anteriormente descritas. A modo comparativo se realizaron ensayos de actividad con otro contaminante orgánico tipo, el formaldehído, cuya degradación fotocatalítica fue también excelente (100% de conversión y 80% de mineralización con 24 ppm de HCHO en un caudal de aire seco de 200 ml·min-1). Los buenos resultados de actividad obtenidos confirman las enormes posibilidades que ofrecen los polímeros transparentes en el UV-A como soportes del dióxido de titanio para la eliminación fotocatalítica de contaminantes en aire. ABSTRACT The great industrial and demographic development of recent decades has led to an unsustainable increase of energy and raw materials consumption that negatively affects the environment due to the large amount of waste and pollutants generated. Between emissions generated organic compounds (VOCs), specially the halogenated ones such as trichloroethylene, are particularly important due to its high toxicity and resistance to degradation. The technologies generally used for the degradation of these compounds have serious inconveniences due to the generation of toxic intermediates turn creating the problem of disposal besides the high cost. Among the advanced oxidation processes (AOP), photocatalysis is an attractive and innovative technique with growing interest in its application for the removal of many organic and inorganic compounds, and has emerged as an effective technology in eliminating chlorinated organic compounds such as trichloroethylene. In addition, as it allows the use of sunlight as a source of UV radiation there is a significant reduction of energy costs and operation. Semiconductors suitable to be used as photocatalyst activated by sunlight are those having an energy band comparable to that of the visible or UV-A light (Eg <3,5 eV), being titanium dioxide (TiO2), the most widely used. The main objective of this study is the test of commercial organic polymers as supports for TiO2 to be applied in heterogeneous photocatalysis and its assay for removing trichloroethylene in air. To accomplish that, its optical properties and resistance to photooxidation have been evaluated, and different operating conditions have been tested in order to optimize the fixation of the photocatalyst to obtain a homogeneous coating, with durable and high photocatalytic activity. The plastic materials tested were: polyethylene (PE), ethyl vinyl acetace copolymers with different additives (EVA, EVA-H and EVA -SH), polypropylene (PP), poly methyl (methacrylate) manufactured by sheet moulding and extrusion (PMMA-C and PMMA-E), compact and cellular polycarbonates (PC-C PC-Ce), rigid and flexible polyvinyl chloride (PVC-R and PVC-F), polystyrene (PS) and polyesters (PET and PETG). On the basis of their optical properties PP, PS, PMMA-C, EVA-SH and PVC-R were selected, as they showed a transmittance value greater than 80% in the range of the studied region (λ = 365nm). For the synthesis of the photocatalyst sol-gel technology was employed with multilayers impregnation of the polymers selected by dip-coating, with intermediate TiO2 drying at moderate temperatures. To evaluate the polymers aging due to UV radiation, and the effect of photoactive coating thereon, a study in an sunlight exposure chamber for 150 days was performed, evaluating the chemical resistance and the mechanical strength. The results of infrared spectroscopy and tensile stress test after aging showed the PMMA is the most resistant sample, but a greater degradation in PS, PVC-R and EVA SH, with a visible loss of the coating in all the polymers tested. The photocatalysts prepared on the untreated substrates with three layers of TiO2 showed better activity results when PMMA-C, PET and PS where used. To achieve greater and better fixation of the film to the support, chemical abrasive treatments, with H2SO4 and NaOH, as well as surface functionalization treatments with atmospheric pressure plasma (APP) and low pressure plasma (LPP) technologies were performed. The plasma treatment showed the best results, with an excellent wettability of the substrates that lead to a better and uniform distribution of the photocatalyst compared to the chemical treatments tested, in which no significant improvement was obtained. Also photocatalysts were prepared with the a silicon dioxide previous layer with the help of surfactants (SiO2- 3TiO2 PDDA-and-3TiO2 SiO2FC), obtaining good properties of the film in all cases. The best activity results for LPP-treated samples with three layers of TiO2 were achieved with PMMA-C (91% conversion, in conditions of 30 ppm of TCE and 200 ml·min-1 air flow rate), with a significant improvement of the photocatalytic activity in PVC-R and PS samples too. However, among all the materials assayed, PMMA-C with SiO2FC-3TiO2 coating was the most active one, achieving the highest mineralization grade (45%) and a reaction rate of 1,89 x 10-6 mol· m-2 · s-1, with total trichloroethylene elimination in the same conditions. As a comparative assay, an activity test was also performed with another typical organic contaminant, formaldehyde, also with good results (100% conversion with 24 ppm of HCHO and 200 ml·min-1 gas flow rate). The good activity results obtained in this study confirm the great potential of organic polymers which are transparent in the UV-A as supports for titanium dioxide for photocatalytic removal of air organic pollutants.

New Intermediate band sulphide nanoparticles acting in the full visible light range spectra as an active photocatalyst

Nowadays one of the challenges of materials science is to find new technologies that will be able to make the most of renewable energies. An example of new proposals in this field are the intermediate-band (IB) materials, which promise higher efficiencies in photovoltaic applications (through the intermediate band solar cells), or in heterogeneous photocatalysis (using nanoparticles of them, for the light-induced degradation of pollutants or for the efficient photoevolution of hydrogen from water). An IB material consists in a semiconductor in which gap a new level is introduced [1], the intermediate band (IB), which should be partially filled by electrons and completely separated of the valence band (VB) and of the conduction band (CB). This scheme (figure 1) allows an electron from the VB to be promoted to the IB, and from the latter to the CB, upon absorption of photons with energy below the band gap Eg, so that energy can be absorbed in a wider range of the solar spectrum and a higher current can be obtained without sacrificing the photovoltage (or the chemical driving force) corresponding to the full bandgap Eg, thus increasing the overall efficiency. This concept, applied to photocatalysis, would allow using photons of a wider visible range while keeping the same redox capacity. It is important to note that this concept differs from the classic photocatalyst doping principle, which essentially tries just to decrease the bandgap. This new type of materials would keep the full bandgap potential but would use also lower energy photons. In our group several IB materials have been proposed, mainly for the photovoltaic application, based on extensively doping known semiconductors with transition metals [2], examining with DFT calculations their electronic structures. Here we refer to In2S3 and SnS2, which contain octahedral cations; when doped with Ti or V an IB is formed according to quantum calculations (see e.g. figure 2). We have used a solvotermal synthesis method to prepare in nanocrystalline form the In2S3 thiospinel and the layered compound SnS2 (which when undoped have bandgaps of 2.0 and 2.2 eV respectively) where the cation is substituted by vanadium at a ?10% level. This substitution has been studied, characterizing the materials by different physical and chemical techniques (TXRF, XRD, HR-TEM/EDS) (see e.g. figure 3) and verifying with UV spectrometry that this substitution introduces in the spectrum the sub-bandgap features predicted by the calculations (figure 4). For both sulphide type nanoparticles (doped and undoped) the photocatalytic activity was studied by following at room temperature the oxidation of formic acid in aqueous suspension, a simple reaction which is easily monitored by UV-Vis spectroscopy. The spectral response of the process is measured using a collection of band pass filters that allow only some wavelengths into the reaction system. Thanks to this method the spectral range in which the materials are active in the photodecomposition (which coincides with the band gap for the undoped samples) can be checked, proving that for the vanadium substituted samples this range is increased, making possible to cover all the visible light range. Furthermore it is checked that these new materials are more photocorrosion resistant than the toxic CdS witch is a well know compound frequently used in tests of visible light photocatalysis. These materials are thus promising not only for degradation of pollutants (or for photovoltaic cells) but also for efficient photoevolution of hydrogen from water; work in this direction is now being pursued.