On Cup Anemometer Rotor Aerodynamics

The influence of anemometer rotor shape parameters, such as the cups’ front area or their center rotation radius on the anemometer’s performance was analyzed. This analysis was based on calibrations performed on two different anemometers (one based on magnet system output signal, and the other one based on an opto-electronic system output signal), tested with 21 different rotors. The results were compared to the ones resulting from classical analytical models. The results clearly showed a linear dependency of both calibration constants, the slope and the offset, on the cups’ center rotation radius, the influence of the front area of the cups also being observed. The analytical model of Kondo et al. was proved to be accurate if it is based on precise data related to the aerodynamic behavior of a rotor’s cup.

CFD modelling of the interaction between the Surface Boundary Layer and rotor wake. Comparison of results obtained with different turbulence models and mesh strategies

A simplified CFD wake model based on the actuator disk concept is used to simulate the wind turbine, represented by a disk upon which a distribution of forces, defined as axial momentum sources, are applied on the incoming non-uniform flow. The rotor is supposed to be uniformly loaded, with the exerted forces function of the incident wind speed, the thrust coefficient and the rotor diameter. The model is tested under different parameterizations of turbulence models and validated through experimental measurements downwind of a wind turbine in terms of wind speed deficit and turbulence intensity.

Analytical Calculation of Stall-inception and Surge Points for an Axial-flow Compresor Rotor

Recently, a theoretical criterion to calculate the stability of an axial-flow compressor rotor has been presented in the scientific literature. This theoretical criterion was used for determining the locus of the stability line over the rotor map and for predicting the post-stall evolution of the constant-speed line of a rotor. The main objective of this paper is to improve the predictions of such a model. To do that, the paper proposes a different characterization of the characteristic azimuthal length and a calculation of the ratio of specific heats based on a polytropic exponent. Thanks to these new values, the model predicts two bifurcation points in the behaviour of the flow: the inception point of the instability and the surge point. Experimental data from a pure axial compressor are used to validate the model showing that the prediction of the flow coefficient at the surge point has an error inferior to 5%. For the rotor studied, the paper provides a quantitative and qualitative description of the inception of the instability and of the mechanism involved in the instable region of the compressor map. The paper also discusses the role of rotor efficiency in the position of the bifurcations and gives a sensitivity analysis of its position. Finally, it presents a discussion about how the model can explain the different behaviours exhibited by the same rotor when the flow coefficient is reduced

Low Voltage Ride-through in DFIG Wind Generators by Controlling the Rotor Current without Crowbars

Among all the different types of electric wind generators, those that are based on doubly fed induction generators, or DFIG technology, are the most vulnerable to grid faults such as voltage sags. This paper proposes a new control strategy for this type of wind generator, that allows these devices to withstand the effects of a voltage sag while following the new requirements imposed by grid operators. This new control strategy makes the use of complementary devices such as crowbars unnecessary, as it greatly reduces the value of currents originated by the fault. This ensures less costly designs for the rotor systems as well as a more economic sizing of the necessary power electronics. The strategy described here uses an electric generator model based on space-phasor theory that provides a direct control over the position of the rotor magnetic flux. Controlling the rotor magnetic flux has a direct influence on the rest of the electrical variables enabling the machine to evolve to a desired work point during the transient imposed by the grid disturbance. Simulation studies have been carried out, as well as test bench trials, in order to prove the viability and functionality of the proposed control strategy.

Mathematical Analysis of the Effect of Rotor Geometry on Cup Anemometer Response

The calibration coefficients of two commercial anemometers equipped with different rotors were studied. The rotor cups had the same conical shape, while the size and distance to the rotation axis varied.The analysis was based on the 2-cup positions analytical model, derived using perturbation methods to include second-order effects such as pressure distribution along the rotating cups and friction.Thecomparison with the experimental data indicates a nonuniformdistribution of aerodynamic forces on the rotating cups, with higher forces closer to the rotating axis. The 2-cup analytical model is proven to be accurate enough to study the effect of complex forces on cup anemometer performance.

A panel method free-wake code for aeroelastic rotor predictions

A panel method free-wake model to analyse the rotor flapping is presented. The aerodynamic model consists of a panel method, which takes into account the three-dimensional rotor geometry, and a free-wake model, to determine the wake shape. The main features of the model are the wake division into a near-wake sheet and a far wake represented by a single tip vortex, and the modification of the panel method formulation to take into account this particular wake description. The blades are considered rigid with a flap degree of freedom. The problem solution is approached using a relaxation method, which enforces periodic boundary conditions. Finally, several code validations against helicopter and wind turbine experimental data are performed, showing good agreement

Determinación paramétrica para el análisis de la viabilidad técnico económica de la implantación de un parque de aprovechamiento energético de corrientes marinas mediante un generador en inmersión con rotor de eje horizontal

La presente Tesis se ha centrado en un análisis de la tecnología para la generación de energía eléctrica utilizando las corrientes marinas. El contenido desarrollado ha consistido en un análisis de las distintas alternativas para poder aprovechar la energía oceánica con especial interés en los desarrollos tecnológicos de las corrientes marinas. Posteriormente se ha descrito un nuevo prototipo, basado en un diseño de un generador en inmersión con rotor de eje horizontal con estructura en Y, denominado proyecto GESMEY. Se han analizado diversas localizaciones para poder implantar un prototipo experimental del proyecto GESMEY, así como las posibles localizaciones para implementar un parque de explotación comercial basado en esta tecnología, llegando a conclusiones importantes referidas a la costa española, y definiendo localizaciones muy interesantes en la costa Escocesa. Finalmente se han analizado diversos parámetros de definición de estos parques de aprovechamiento de la energía, clasificándolos como parámetros técnicos, de ubicación, de utilización, medioambientales y económicos. A la vista de la investigación realizada se ha concluido que hay muchas líneas de investigación que desarrollar, y que desde un punto de vista estratégico hay muchas actuaciones que poner en marcha para potenciar la tecnología de las energías renovables marinas mediante corrientes marinas. ABSTRACT This thesis has focused on an analysis of technology for generating electrical power using ocean currents. The content developed consisted of an analysis of the alternatives to take advantage of ocean energy with special emphasis on the technological developments of ocean currents. Subsequently it described a new prototype, based on a design of a generator rotor immersion horizontal axis Y structure, called GESMEY project. We analyzed different locations to implement an experimental prototype GESMEY project and possible locations to deploy a fleet of commercial exploitation based on this technology, reaching important conclusions regarding the Spanish coast, and defining interesting locations on the coast Scottish. Finally, we have analyzed various parameters defining these parks use of energy, classifying them as technical parameters, location, utilization, environmental and economic. In view of the conducted research has concluded that there are many lines of research to develop, and that from a strategic point of view there are many actions to implement to enhance the technology of marine renewable energies by sea currents.

Deviations of cup anemometer rotational speed measurements due to steady state harmonic accelerations of the rotor

The measurement deviations of cup anemometers are studied by analyzing the rotational speed of the rotor at steady state (constant wind speed). The differences of the measured rotational speed with respect to the averaged one based on complete turns of the rotor are produced by the harmonic terms of the rotational speed. Cup anemometer sampling periods include a certain number of complete turns of the rotor, plus one incomplete turn, the residuals from the harmonic terms integration within that incomplete turn (as part of the averaging process) being responsible for the mentioned deviations. The errors on the rotational speed due to the harmonic terms are studied analytically and then experimentally, with data from more than 500 calibrations performed on commercial anemometers.

New Fault-Resistance Estimation Algorithm for Rotor-Winding Ground-Fault Online Location in Synchronous Machines With Static Excitation

New Fault-Resistance Estimation Algorithm for Rotor-Winding Ground-Fault Online Location in Synchronous Machines With Static Excitation