Estimating Perceived Video Quality from Objective Parameters in Video over IP Services

In Video over IP services, perceived video quality heavily depends on parameters such as video coding and network Quality of Service. This paper proposes a model for the estimation of perceived video quality in video streaming and broadcasting services that combines the aforementioned parameters with other that depend mainly on the information contents of the video sequences. These fitting parameters are derived from the Spatial and Temporal Information contents of the sequences. This model does not require reference to the original video sequence so it can be used for online, real-time monitoring of perceived video quality in Video over IP services. Furthermore, this paper proposes a measurement workbench designed to acquire both training data for model fitting and test data for model validation. Preliminary results show good correlation between measured and predicted values.

Evaluation of the influence of visual parameters on wave transmission velocity in sawn chestnut timber

Non-destructive, visual evaluation and mechanical testing techniques were used to assess the structural properties of 374 samples of chestnut (Castanea sativa). The principal components method was applied to establish and interpret correlations between variables obtained of modulus of elasticity, bending strength and density. The static modulus of elasticity presented higher correlation values than those obtained using non-destructive methods. Bending strength presented low correlations with the non-destructive parameters, but there was some relation to the different knot ratios defined. The relationship was stronger with the most widely used ratio, CKDR. No significant correlations were observed between any of the variables and density.

Application of digital image correlation at the microscale in fiber-reinforced composites

Digital image correlation (DIC) is applied to analyzing the deformation mechanisms under transverse compression in a fiber-reinforced composite. To this end, compression tests in a direction perpendicular to the fibers were carried out inside a scanning electron microscope and secondary electron images obtained at different magnifications during the test. Optimum DIC parameters to resolve the displacement and strain field were computed from numerical simulations of a model composite and they were applied to micrographs obtained at different magnifications (250_, 2000_, and 6000_). It is shown that DIC of low-magnification micrographs was able to capture the long range fluctuations in strain due to the presence of matrix-rich and fiber-rich zones, responsible for the onset of damage. At higher magnification, the strain fields obtained with DIC qualitatively reproduce the non-homogeneous deformation pattern due to the presence of stiff fibers dispersed in a compliant matrix and provide accurate results of the average composite strain. However, comparison with finite element simulations revealed that DIC was not able to accurately capture the average strain in each phase.

Perturbed angular correlation study of Ta-181-doped PbTi1-xHfxO3 compounds

In this work, the hyperfine quadrupole interaction at Ta-doped PbTi1-xHfxO3 polycrystalline samples is studied for the first time. Powders with x=0.25, 0.50 and 0.75 were prepared and characterized by X-ray diffraction analysis. Perturbed Angular Correlation (PAC) analyses were done as a function of temperature, using low concentration Ta-181 nuclei as probes. In the ferroelectric and paraelectric phases of these compounds two sites were occupied by the probes. For each site the quadrupole frequency, asymmetry and relative distribution width parameters were obtained as a function of temperature above and below the Curie temperature (T-C). One of these sites was assigned to the regular Ti-Hf site, while the other one was assigned to some kind of defect. The behavior of the hyperfine parameters as a function of temperature was analyzed in terms of a recent published phase diagram and the presence of disorder below and above T-C. For the three compositions measured, the obtained hyperfine parameters present discontinuities which correspond to the ferroelectric-paraelectric phase transition. In both phases it was found broad frequency distributed interactions. The disorder in the electronic distribution would be responsible for the broad line width of the hyperfine interaction. (C) 2012 Elsevier B.V. All rights reserved.

Selection of TDOA Parameters for MDM Speaker Diarization

Several methods to improve multiple distant microphone (MDM) speaker diarization based on Time Delay of Arrival (TDOA) features are evaluated in this paper. All of them avoid the use of a single reference channel to calculate the TDOA values and, based on different criteria, select among all possible pairs of microphones a set of pairs that will be used to estimate the TDOA's. The evaluated methods have been named the "Dynamic Margin" (DM), the "Extreme Regions" (ER), the "Most Common" (MC), the "Cross Correlation" (XCorr) and the "Principle Component Analysis" (PCA). It is shown that all methods improve the baseline results for the development set and four of them improve also the results for the evaluation set. Improvements of 3.49% and 10.77% DER relative are obtained for DM and ER respectively for the test set. The XCorr and PCA methods achieve an improvement of 36.72% and 30.82% DER relative for the test set. Moreover, the computational cost for the XCorr method is 20% less than the baseline.

Integration of Correlation Processes in Design Systems.

The integration of correlation processes in design systems has as a target measurements in 3D directly and according to the users criteria in order to generate the required database for the development of the project. In the phase of photogrammetric works, internal and external orientation parameters are calculated and stereo models are created from standard images. The aforementioned are integrated in the system where the measurement of the selected items is done by applying developed correlation algorithms. The processing period has the tools to carry out the calculations in an easy and automatic way, as well as image measurement techniques to acquire the most correct information. The proposed software development is done on Visual Studio platforms for PC, applying the most apt codes and symbols according to the terms of reference required for the design. The results of generating the data base in an interactive way with the geometric study of the structures, facilitates and improves the quality of the works in the projects.

Impact parameters in relation to bruising and other fruit properties.

Impact response in fruits, primarily appl.es and pears (Pomaceae fruits), has been studied during the last five years. Using a laboratory impact testing device and also free-fall tests of instrumented apples, a significant body of results has been established, relative to the parameters which best characterize the impact response of these materials, and to their correlation with bruise damage, variety and ripeness level of the fruits. Bruise damage, measured as the size and/or volume of the affected fruit tissue is related primarily to applied energy (i.e. mainly drop height) for a given variety at a given ripeness stage. The relevant impact response parameters are maximum deformation (DM), permanent deformation (DP), maximum impulse (IM), maximum impact force (FM), maximum value of the force/time slope during impact (F/T) and impact time (T). The effect of ripeness differences was also studied in selected varieties of pears, being the most relevant parameters: maximum force (FM) and F/T slope.