Self-Tuning PID controller for autonomous car tracking in urban traffic

In this paper an on line self-tuned PID controller is proposed for the control of a car whose goal is to follow another one, at distances and speeds typical in urban traffic. The bestknown tuning mechanism is perhaps the MIT rule, due to its ease of implementation. However, as it is well known, this method does not guarantee the stability of the system, providing good results only for constant or slowly varying reference signals and in the absence of noise, which are unrealistic conditions. When the reference input varies with an appreciable rate or in presence of noise, eventually it could result in system instability. In this paper an alternative method is proposed that significantly improves the robustness of the system for varying inputs or in the presence of noise, as demonstrated by simulation.

Diseño e implementación de un controlador de velocidad PID multivariable para un robot con configuración de triciclo

La robótica móvil constituye un área de desarrollo y explotación de interés creciente. Existen ejemplos de robótica móvil de relevancia destacada en el ámbito industrial y se estima un fuerte crecimiento en el terreno de la robótica de servicios. En la arquitectura software de todos los robots móviles suelen aparecer con frecuencia componentes que tienen asignadas competencias de gobierno, navegación, percepción, etcétera, todos ellos de importancia destacada. Sin embargo, existe un elemento, difícilmente prescindible en este tipo de robots, el cual se encarga del control de velocidad del dispositivo en sus desplazamientos. En el presente proyecto se propone desarrollar un controlador PID basado en el modelo y otro no basado en el modelo. Dichos controladores deberán operar en un robot con configuración de triciclo disponible en el Departamento de Sistemas Informáticos y deberán por tanto ser programados en lenguaje C para ejecutar en el procesador digital de señal destinado para esa actividad en el mencionado robot (dsPIC33FJ128MC802). ABSTRACT Mobile robotics constitutes an area of development and exploitation of increasing interest. There are examples of mobile robotics of outstanding importance in industry and strong growth is expected in the field of service robotics. In the software architecture of all mobile robots usually appear components which have assigned competences of government, navigation, perceptionetc., all of them of major importance. However, there is an essential element in this type of robots, which takes care of the speed control. The present project aims to develop a model-based and other non-model-based PID controller. These controllers must operate in a robot with tricycle settings, available from the Department of Computing Systems, and should therefore be programmed in C language to run on the digital signal processor dedicated to that activity in the robot (dsPIC33FJ128MC802).

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented.

Modelización tridimensional de ensayos de adherencia tipo viga del refuerzo NSM-FRP en hormigón

El uso de refuerzos NSM‐FRP en estructuras de hormigón armado se ha incrementado considerablemente en los últimos años como método de refuerzo estructural. Los ensayos de arrancamiento en viga de los refuerzos NSM‐FRP permiten el estudio del comportamiento de la unión pegada. El principal objetivo del presente trabajo aborda la simulación numérica de este tipo de ensayos, con el propósito de caracterizar correctamente la adherencia entre las barras de NSM‐FRP y el hormigón. En una fase inicial se simuló un modelo bidimensional para conseguir evaluar y verificar el comportamiento de los elementos cohesivos y ver su comportamiento primero ante diferentes modelos de material y segundo ante un modo mixto de fallo, debido a la aplicación simultanea de carga axial y carga cortante. En una segunda fase se creó un modelo tridimensional para estudiar el arrancamiento de una barra de material compuesto insertada en hormigón, creando un modelo de material de hormigón y viendo el comportamiento cualitativo del sistema ante variaciones en los parámetros de los diferentes materiales. En la tercera fase, la más importante del presente trabajo, se abordó la simulación numérica del ensayo de arrancamiento en viga. Se simularon todos los componentes del ensayo y se evaluaron diferentes alternativas para representar la interfase NSM‐FRP ‐ hormigón, usando elementos cohesivos y diferentes distribuciones de los mismos en la interfase. Para conseguir representar lo más fielmente posible las condiciones del ensayo, se diseñó también un controlador PID que permite realizar las simulaciones numéricas mediante un control en desplazamientos, lo cual permite capturar más correctamente el comportamiento de reblandecimiento de la unión pegada. El controlador PID aplica técnicas de ingeniería de control para conseguir calcular a priori la amplitud necesaria del desplazamiento impuesto que provoque una evolución establecida en una variable interna del sistema. La variable usada para correlacionar los ensayos es la diferencia en desplazamientos entre dos puntos y se escoge una evolución lineal de la misma, pero en la tesis también se exponen los resultados de escoger otras posibles variables internas con diferentes evoluciones. Se compararon las simulaciones numéricas con resultados de mediciones experimentales previamente publicadas. Los resultados carga‐deslizamiento obtenidos encajan bien con los datos experimentales. El modelo propuesto es también capaz de predecir el modo de fallo en la interfase NSM‐FRP ‐ hormigón. Finalmente, también se han llevado a cabo estudios paramétricos, para evaluar la influencia de cada parámetro en los resultados. También se realizó un estudio cualitativo de cómo se comporta la unión pegada en cada momento de la simulación, mediante el uso macros y gráficas tridimensionales, para conseguir una mejor visualización y facilitar el análisis de los resultados. ABSTRACT The use of near‐surface mounted FRP reinforcement in reinforced concrete structures has seen a considerable increase in recent years as a strengthening method. Beam pull‐out tests for near‐surface reinforcement allow obtaining the local bond‐slip behavior of a bonded joint. The main objective of the current work deals with the three‐dimensional modeling of this kind of test with the purpose of characterizing suitably the mechanics of bond between FRP rods and concrete. In an initial stage, a two bidimensional in order to evaluate and to verify the behavior of the cohesive elements. Its behavior was evaluated first testing different material models and second testing the behavior when mixed mode failure appears, due to simultaneous axial and shear load. In a second stage a tridimensional model was created in order to study the pull‐out of an inserted beam of composite material in concrete. A concrete material model was created and the influence of each material parameter was studied qualitatively. The third part, the most relevant of the present work, the numerical simulation of the Beam Pull‐Out test was faced. All the parts of the Beam Pull‐Out test were included inthe simulation and different alternatives to represent the FRP bar – concrete interface have been evaluated, using cohesive elements and different distributions of them. In order to reproduce the test conditions more reliably, a PID controller has also been designed to conduct suitably the numerical tests in order to properly capture the softening branch of the load‐slip behaviour. The PID controller applies control techniques to calculate a priori the necessary amplitude of the load in order to achieve a given evolution through the simulation of an internal variable previously chosen. The variable used in order to correlate the simulation with the test results is the difference in displacements between two points and a linear evolution was chosen, but in the thesis the results of choosing other possible internal variables with different evolutions are also shown. The numerical FE simulations were compared with experimental measurements previously published. Load‐slip predictions compare well with the corresponding experimental data. The proposed model is also able to predict the failure mode at the FRP‐concrete interface. Some parametric studies have also been carried out, in order to evaluate the influence of each material parameter in the results. A qualitative study of the behaviour of the joint was also performed, using the results of the numeric simulations and through the use of macros and 3D graphs, the tensional state of each point of the joint can be visualized in each moment of the simulation.

Detecting, Localizing and Following Dynamic Objects with a Mini-UAV

This paper presents an approach for the detection, localization and following of dynamic terrestrial objects using a mini-UAV. The development is intended to be used for surveillance of large infrastructures. The detection algorithm is based on finding several pre-defined characteristics of the target, such as color, shape and size. The process used to localize the target, once it is detected, is based on an inversion of the Pinhole camera model. The task of following the Summit XL was designed to keep the target inside the field of view of the camera, and it was implemented in the form of a PID controller. The system has been tested both in simulation and with real robots, showing promising results.

Automatic Understanding of ATC Speech: Study of Prospectives and Field Experiments for Several Controller Positions

Although there has been a lot of interest in recognizing and understanding air traffic control (ATC) speech, none of the published works have obtained detailed field data results. We have developed a system able to identify the language spoken and recognize and understand sentences in both Spanish and English. We also present field results for several in-tower controller positions. To the best of our knowledge, this is the first time that field ATC speech (not simulated) is captured, processed, and analyzed. The use of stochastic grammars allows variations in the standard phraseology that appear in field data. The robust understanding algorithm developed has 95% concept accuracy from ATC text input. It also allows changes in the presentation order of the concepts and the correction of errors created by the speech recognition engine improving it by 17% and 25%, respectively, absolute in the percentage of fully correctly understood sentences for English and Spanish in relation to the percentages of fully correctly recognized sentences. The analysis of errors due to the spontaneity of the speech and its comparison to read speech is also carried out. A 96% word accuracy for read speech is reduced to 86% word accuracy for field ATC data for Spanish for the "clearances" task confirming that field data is needed to estimate the performance of a system. A literature review and a critical discussion on the possibilities of speech recognition and understanding technology applied to ATC speech are also given.

Pond head level control in a run-of-river hydro power plant using fuzzy controller

The run-of-river hydro power plant usually have low or nil water storage capacity, and therefore an adequate control strategy is required to keep the water level constant in pond. This paper presents a novel technique based on TSK fuzzy controller to maintain the pond head constant. The performance is investigated over a wide range of hill curve of hydro turbine. The results are compared with PI controller as discussed in [1].

ITER fast plant system controller prototype based on PXIe platform

The ITER CODAC design identifies slow and fast plant system controllers (PSC). The gast OSCs are based on embedded technologies, permit sampling rates greater than 1 KHz, meet stringent real-time requirements, and will be devoted to data acquisition tasks and control purposes. CIEMAT and UPM have implemented a prototype of a fast PSC based on commercial off-the-shelf (COTS) technologies with PXI hardware and software based on EPICS

ITER Fast Plant System Controller Prototype Based on Commercial PXI Platform

The ITER CODAC design identifies slow and fast plant system controllers (PSC). The gast OSCs are based on embedded technologies, permit sampling rates greater than 1 KHz, meet stringent real-time requirements, and will be devoted to data acquisition tasks and control purposes. CIEMAT and UPM have implemented a prototype of a fast PSC based on commercial off-the-shelf (COTS) technologies with PXI hardware and software based on EPICS

Non-linear Control of an Autonomous Ground Vehicle

In this paper, in order to select a speed controller for a specific non-linear autonomous ground vehicle, proportional-integral-derivative (PID), Fuzzy, and linear quadratic regulator (LQR) controllers were designed. Here, in order to carry out the tuning of the above controllers, a multicomputer genetic algorithm (MGA) was designed. Then, the results of the MGA were used to parameterize the PID, Fuzzy and LQR controllers and to test them under laboratory conditions. Finally, a comparative analysis of the performance of the three controllers was conducted.

Neural network controller for active demand side management with PV energy in the residential sector

In this paper, we describe the development of a control system for Demand-Side Management in the residential sector with Distributed Generation. The electrical system under study incorporates local PV energy generation, an electricity storage system, connection to the grid and a home automation system. The distributed control system is composed of two modules: a scheduler and a coordinator, both implemented with neural networks. The control system enhances the local energy performance, scheduling the tasks demanded by the user and maximizing the use of local generation.

Cross-entropy optimization for scaling factors of a fuzzy controller: a see-and-avoid approach for unmanned aerial systems

The Cross-Entropy (CE) is an efficient method for the estimation of rare-event probabilities and combinatorial optimization. This work presents a novel approach of the CE for optimization of a Soft-Computing controller. A Fuzzy controller was designed to command an unmanned aerial system (UAS) for avoiding collision task. The only sensor used to accomplish this task was a forward camera. The CE is used to reach a near-optimal controller by modifying the scaling factors of the controller inputs. The optimization was realized using the ROS-Gazebo simulation system. In order to evaluate the optimization a big amount of tests were carried out with a real quadcopter.

Adaptive control system based on lineal control theory for the path-following problem of a car-like mobile robot

The objective of this paper is to design a path following control system for a car-like mobile robot using classical linear control techniques, so that it adapts on-line to varying conditions during the trajectory following task. The main advantages of the proposed control structure is that well known linear control theory can be applied in calculating the PID controllers to full control requirements, while at the same time it is exible to be applied in non-linear changing conditions of the path following task. For this purpose the Frenet frame kinematic model of the robot is linearised at a varying working point that is calculated as a function of the actual velocity, the path curvature and kinematic parameters of the robot, yielding a transfer function that varies during the trajectory. The proposed controller is formed by a combination of an adaptive PID and a feed-forward controller, which varies accordingly with the working conditions and compensates the non-linearity of the system. The good features and exibility of the proposed control structure have been demonstrated through realistic simulations that include both kinematics and dynamics of the car-like robot.

Estudio de la fiabilidad software, según defectos, en controladores de velocidad para robots autónomos móviles

Tanto los robots autónomos móviles como los robots móviles remotamente operados se utilizan con éxito actualmente en un gran número de ámbitos, algunos de los cuales son tan dispares como la limpieza en el hogar, movimiento de productos en almacenes o la exploración espacial. Sin embargo, es difícil garantizar la ausencia de defectos en los programas que controlan dichos dispositivos, al igual que ocurre en otros sectores informáticos. Existen diferentes alternativas para medir la calidad de un sistema en el desempeño de las funciones para las que fue diseñado, siendo una de ellas la fiabilidad. En el caso de la mayoría de los sistemas físicos se detecta una degradación en la fiabilidad a medida que el sistema envejece. Esto es debido generalmente a efectos de desgaste. En el caso de los sistemas software esto no suele ocurrir, ya que los defectos que existen en ellos generalmente no han sido adquiridos con el paso del tiempo, sino que han sido insertados en el proceso de desarrollo de los mismos. Si dentro del proceso de generación de un sistema software se focaliza la atención en la etapa de codificación, podría plantearse un estudio que tratara de determinar la fiabilidad de distintos algoritmos, válidos para desempeñar el mismo cometido, según los posibles defectos que pudieran introducir los programadores. Este estudio básico podría tener diferentes aplicaciones, como por ejemplo elegir el algoritmo menos sensible a los defectos, para el desarrollo de un sistema crítico o establecer procedimientos de verificación y validación, más exigentes, si existe la necesidad de utilizar un algoritmo que tenga una alta sensibilidad a los defectos. En el presente trabajo de investigación se ha estudiado la influencia que tienen determinados tipos de defectos software en la fiabilidad de tres controladores de velocidad multivariable (PID, Fuzzy y LQR) al actuar en un robot móvil específico. La hipótesis planteada es que los controladores estudiados ofrecen distinta fiabilidad al verse afectados por similares patrones de defectos, lo cual ha sido confirmado por los resultados obtenidos. Desde el punto de vista de la planificación experimental, en primer lugar se realizaron los ensayos necesarios para determinar si los controladores de una misma familia (PID, Fuzzy o LQR) ofrecían una fiabilidad similar, bajo las mismas condiciones experimentales. Una vez confirmado este extremo, se eligió de forma aleatoria un representante de clase de cada familia de controladores, para efectuar una batería de pruebas más exhaustiva, con el objeto de obtener datos que permitieran comparar de una forma más completa la fiabilidad de los controladores bajo estudio. Ante la imposibilidad de realizar un elevado número de pruebas con un robot real, así como para evitar daños en un dispositivo que generalmente tiene un coste significativo, ha sido necesario construir un simulador multicomputador del robot. Dicho simulador ha sido utilizado tanto en las actividades de obtención de controladores bien ajustados, como en la realización de los diferentes ensayos necesarios para el experimento de fiabilidad. ABSTRACT Autonomous mobile robots and remotely operated robots are used successfully in very diverse scenarios, such as home cleaning, movement of goods in warehouses or space exploration. However, it is difficult to ensure the absence of defects in programs controlling these devices, as it happens in most computer sectors. There exist different quality measures of a system when performing the functions for which it was designed, among them, reliability. For most physical systems, a degradation occurs as the system ages. This is generally due to the wear effect. In software systems, this does not usually happen, and defects often come from system development and not from use. Let us assume that we focus on the coding stage in the software development pro¬cess. We could consider a study to find out the reliability of different and equally valid algorithms, taking into account any flaws that programmers may introduce. This basic study may have several applications, such as choosing the algorithm less sensitive to pro¬gramming defects for the development of a critical system. We could also establish more demanding procedures for verification and validation if we need an algorithm with high sensitivity to programming defects. In this thesis, we studied the influence of certain types of software defects in the reliability of three multivariable speed controllers (PID, Fuzzy and LQR) designed to work in a specific mobile robot. The hypothesis is that similar defect patterns affect differently the reliability of controllers, and it has been confirmed by the results. From the viewpoint of experimental planning, we followed these steps. First, we conducted the necessary test to determine if controllers of the same family (PID, Fuzzy or LQR) offered a similar reliability under the same experimental conditions. Then, a class representative was chosen at ramdom within each controller family to perform a more comprehensive test set, with the purpose of getting data to compare more extensively the reliability of the controllers under study. The impossibility of performing a large number of tests with a real robot and the need to prevent the damage of a device with a significant cost, lead us to construct a multicomputer robot simulator. This simulator has been used to obtain well adjusted controllers and to carry out the required reliability experiments.

Quadcopter see and avoid using a fuzzy controller

Unmanned Aerial Vehicles (UAVs) industry is a fast growing sector. Nowadays, the market offers numerous possibilities for off-the-shelf UAVs such as quadrotors or fixed-wings. Until UAVs demonstrate advance capabilities such as autonomous collision avoidance they will be segregated and restricted to flight in controlled environments. This work presents a visual fuzzy servoing system for obstacle avoidance using UAVs. To accomplish this task we used the visual information from the front camera. Images are processed off-board and the result send to the Fuzzy Logic controller which then send commands to modify the orientation of the aircraft. Results from flight test are presented with a commercial off-the-shelf platform.