Multi-UAV Coordination and Control Interface

The interest in missions with multiple Unmanned Aerial Vehicles (UAVs) has increased significantly in last years. These missions take advantage of the use of fleets instead of single UAVs to ensure the success, reduce the duration or increase the goals of the mission. In addition, they allow performing tasks that require multiple agents and certain coordination (e.g. surveillance of large areas or transport of heavy loads). Nevertheless, these missions suppose a challenge in terms of control and monitoring. In fact, the workload of the operators rises with the utilization of multiple UAVs and payloads, since they have to analyze more information, make more decisions and generate more commands during the mission. This work addresses the operator workload problem in multi-UAV missions by reducing and selecting the information. Two approaches are considered: a first one that selects the information according to the mission state, and a second one that selects it according to the operator preferences. The result is an interface that is able to control the amount of information and show what is relevant for mission and operator at the time.

Modelo de gestión de costes medioambientales para el sector petroquímico venezolano

El crecimiento económico ha producido mejoras en el nivel de vida de la población que muchas veces tienen efectos medioambientales negativos en el largo plazo. Ante esta problemática, surge la necesidad a nivel empresarial de enmarcarse en un modelo de desarrollo sostenible que combine los objetivos de crecimiento económico con los de protección medioambiental. Esta situación puede representar altos costes para las empresas del sector petroquímico venezolano, debido al elevado riesgo de sus operaciones y al conjunto de regulaciones legales vigentes en materia medioambiental. Por lo tanto, el objetivo de la presente investigación ha sido proponer un modelo para la gestión de costes medioambientales de dicho sector fundamentado en la ecoeficiencia. Se planteó una investigación proyectiva, desde un enfoque holístico. Se utilizó un diseño de investigación univariable, transeccional contemporáneo, de fuente mixta. Univariable, porque se enfoca en la gestión de costes medioambientales como único evento a modificar. Transeccional contemporáneo, porque el evento se estudia en la actualidad y la medición de los datos se realiza en un solo momento. De fuente mixta, porque se combinó un diseño documental con un diseño de campo. Se utilizó un diseño documental para el análisis comparativo de las normativas de registro y control de costes medioambientales propuestas por organismos internacionales, mediante la aplicación de una matriz de análisis de categorías emergentes. Para el diagnóstico de la gestión de costes medioambientales en el sector petroquímico venezolano, se utilizó un diseño de campo en las empresas del sector que operan en la región zuliana. Para ello se aplicó un cuestionario con 100 ítems en escala Likert y 6 preguntas de opción múltiple. Dicho cuestionario fue validado mediante la revisión de expertos y se determinó su confiablidad a través del coeficiente alfa de Cronbach. Los resultados muestran que los principales asuntos tratados por las normativas analizadas pueden agruparse en seis temas: alcance de la contabilidad de gestión medioambiental, clasificación, tratamiento contable, asignación, informes de costes medioambientales e indicadores de gestión. Se evidenció que las guías de aplicación de la contabilidad de gestión medioambiental abordan todos los temas identificados pero no hay uniformidad en los criterios asumidos. Por el contrario, las normativas en el ámbito de la contabilidad financiera consideran principalmente los aspectos relacionados con el tratamiento contable de los costes medioambientales y su inclusión en los estados financieros. En cuanto a la gestión de costes medioambientales que realizan las empresas del sector petroquímico venezolano, se evidenció su limitación por la escasa consideración de criterios de ecoeficiencia y la poca aplicación de herramientas de contabilidad de gestión, que dificultan la determinación y el control de costes medioambientales. Tomando como base los resultados obtenidos, se diseñó el modelo de Gestión de Costes Medioambientales Ecoeficiente (GCME). Dicho modelo plantea como deben incorporarse los criterios de ecoeficiencia y las herramientas de contabilidad de gestión medioambiental para la planificación, coordinación y control en la gestión de costes medioambientales. Se plantea que estas etapas deben desarrollarse permanentemente para asegurar la mejora continua del proceso y su adaptación a los cambios tecnológicos y a las regulaciones legales. Se hace énfasis en las directrices que deben seguir las empresas del sector petroquímico venezolano para la aplicación del modelo GCME. Sin embargo, por su generalidad y adaptación a las Normas Internacionales de Contabilidad vigentes en Venezuela, dicho modelo es aplicable a diversos sectores industriales que requieran mejorar su desempeño económico-medioambiental. ABSTRACT Economic growth has led to improvements in the standard of living of the population that often have negative environmental effects over the long term. Faced with this problem, at the enterprise-level, the need to be framed in a sustainable development model that combines the goals of economic growth with environmental protection arises. This situation may represent high costs for the Venezuelan petrochemical companies due to the high risk of their operations and to all the applicable legal regulations on environmental matters. Therefore, this research aims to propose a model for the environmental costs management of these companies based on eco-efficiency. A projective research was performed from a holistic approach. An univariate, contemporary cross-sectional and mixed source research design was used. It is univariate, because it focuses on environmental costs management as the single event to change. It is contemporary cross-sectional, because the event is currently studied and the data measurement is performed in a single moment. It relies on mixed source, because it combines a documentary design with a field design. A documentary design was used for the comparative analysis of the standards of registration and control of environmental costs proposed by international organizations, by applying an analysis matrix of emerging categories. For the diagnosis of the environmental costs management in the Venezuelan petrochemical industry, a field design was applied in the companies that operate in the Zulia region. A questionnaire with 100 items on a Likert scale and 6 multiple-choice questions was used. The questionnaire was validated by peer review and internal consistency reliability was determined using Cronbach's alpha coefficient. The results show that the main issues addressed in the analyzed regulations can be grouped into six themes: scope of environmental management accounting, classification, accounting, allocation, reporting of environmental costs and performance indicators. It was evident that implementation guides of environmental management accounting address all issues identified but there is no uniformity in the assumed criteria. Meanwhile, regulations in the financial accounting field mainly consider aspects related to the accounting treatment of environmental costs and their inclusion in the financial statements. Regarding the environmental costs management performed by Venezuelan petrochemical companies, its limitations were made evident by the low status of eco-efficiency criteria and insufficient application of management accounting tools, which hinder the identification and control of environmental costs. Based on the results, the model of eco-efficient environmental costs management (EECM) was designed. This model indicates how eco-efficiency criteria and tools of environmental management accounting for planning, coordination and control in the environmental costs management should be incorporated. It argues that these stages must be continually developed to ensure a continuous process improvement and its adaptation to technological and legal regulatory changes. The guidelines which the Venezuelan petrochemical companies should follow for the EECM model application have been emphasized. However, due to its generality and adaptation to the International Accounting Standards enforced in Venezuela, this model is applicable to various industries that require an improvement of their economic and environmental performance.

Coordination mechanisms and software in industrial networks - a literature review

This paper groups recent supply chain management research focused on organizational design and its software support. The classification encompasses criteria related to research methodology and content. Empirical studies from management science focus on network types and organizational fit. Novel planning algorithms and innovative coordination schemes are developed mostly in the field of operations research in order to propose new software features. Operations and production management realize cost-benefit analysis of IT software implementations. The success of software solutions for network coordination depends strongly on the fit of three dimensions: network configuration, coordination scheme and software functionality. This paper concludes with proposals for future research on unaddressed issues within and among the identified research streams.

Seismic Risk Scenarios in Puerto Principe (Haiti). A Tool for Reconstruction and Emergency Planning

The 12 January 2010, an earthquake hit the city of Port-au-Prince, capital of Haiti. The earthquake reached a magnitude Mw 7.0 and the epicenter was located near the town of Léogâne, approximately 25 km west of the capital. The earthquake occurred in the boundary region separating the Caribbean plate and the North American plate. This plate boundary is dominated by left-lateral strike slip motion and compression, and accommodates about 20 mm/y slip, with the Caribbean plate moving eastward with respect to the North American plate (DeMets et al., 2000). Initially the location and focal mechanism of the earthquake seemed to involve straightforward accommodation of oblique relative motion between the Caribbean and North American plates along the Enriquillo-Plantain Garden fault system (EPGFZ), however Hayes et al., (2010) combined seismological observations, geologic field data and space geodetic measurements to show that, instead, the rupture process involved slip on multiple faults. Besides, the authors showed that remaining shallow shear strain will be released in future surface-rupturing earthquakes on the EPGFZ. In December 2010, a Spanish cooperation project financed by the Politechnical University of Madrid started with a clear objective: Evaluation of seismic hazard and risk in Haiti and its application to the seismic design, urban planning, emergency and resource management. One of the tasks of the project was devoted to vulnerability assessment of the current building stock and the estimation of seismic risk scenarios. The study was carried out by following the capacity spectrum method as implemented in the software SELENA (Molina et al., 2010). The method requires a detailed classification of the building stock in predominant building typologies (according to the materials in the structure and walls, number of stories and age of construction) and the use of the building (residential, commercial, etc.). Later, the knowledge of the soil characteristics of the city and the simulation of a scenario earthquake will provide the seismic risk scenarios (damaged buildings). The initial results of the study show that one of the highest sources of uncertainties comes from the difficulty of achieving a precise building typologies classification due to the craft construction without any regulations. Also it is observed that although the occurrence of big earthquakes usually helps to decrease the vulnerability of the cities due to the collapse of low quality buildings and the reconstruction of seismically designed buildings, in the case of Port-au-Prince the seismic risk in most of the districts remains high, showing very vulnerable areas. Therefore the local authorities have to drive their efforts towards the quality control of the new buildings, the reinforcement of the existing building stock, the establishment of seismic normatives and the development of emergency planning also through the education of the population.

Integrated planning for ecological urban regeneration

Considering that the vast majority of housing stock existing in 2011 will be used to satisfy residential needs in the year 2020 and beyond, ecological urban regeneration appears clearly as the key issue in relation to global urban sustainability for the most part of this century. Thus, if the 1992 Rio Summit identified the urban environment as the main arena where the global environmental crisis should be fought, 20 years later we must emphasize that it is mainly to the real cities and territories around us now where we should address our attention

Use of prediction methods for patent and trademark applications in Spain

Patent and trademark offices which run according to principles of new management have an inherent need for dependable forecasting data in planning capacity and service levels. The ability of the Spanish Office of Patents and Trademarks to carry out efficient planning of its resource needs requires the use of methods which allow it to predict the changes in the number of patent and trademark applications at different time horizons. The approach for the prediction of time series of Spanish patents and trademarks applications (1979e2009) was based on the use of different techniques of time series prediction in a short-term horizon. The methods used can be grouped into two specifics areas: regression models of trends and time series models. The results of this study show that it is possible to model the series of patents and trademarks applications with different models, especially ARIMA, with satisfactory model adjustment and relatively low error.

Configuration management and product lines to enhance the replication process in software engineering

This research is concerned with the experimental software engineering area, specifically experiment replication. Replication has traditionally been viewed as a complex task in software engineering. This is possibly due to the present immaturity of the experimental paradigm applied to software development. Researchers usually use replication packages to replicate an experiment. However, replication packages are not the solution to all the information management problems that crop up when successive replications of an experiment accumulate. This research borrows ideas from the software configuration management and software product line paradigms to support the replication process. We believe that configuration management can help to manage and administer information from one replication to another: hypotheses, designs, data analysis, etc. The software product line paradigm can help to organize and manage any changes introduced into the experiment by each replication. We expect the union of the two paradigms in replication to improve the planning, design and execution of further replications and their alignment with existing replications. Additionally, this research work will contribute a web support environment for archiving information related to different experiment replications. Additionally, it will provide flexible enough information management support for running replications with different numbers and types of changes. Finally, it will afford massive storage of data from different replications. Experimenters working collaboratively on the same experiment must all have access to the different experiments.

Building the qualification and a skill development program within the ENEN-III European Project

The ENEN III project covers the structuring, organization, coordination and implementation of training schemes in cooperation with local, national and international training organizations, to provide training to professionals active in nuclear organizations or their contractors and sub-contractors. The training schemes provide a portfolio of courses, training sessions, seminars, and workshops for continuous learning for upgrading knowledge and developing skills. The training schemes allow individuals to acquire qualifications and skills, as required by the specific positions in the nuclear sector which will be documented in a training passport. The essence of such passport is to be recognized within the EU by the whole nuclear sector which provides mobility to the individual looking for employment and an EU wide recruitment field for the nuclear employers.

Contribution to flexible service coordination in mobile prosumer environments

Este trabajo de Tesis se desarrolla en el marco de los escenarios de ejecución distribuida de servicios móviles y contribuye a la definición y desarrollo del concepto de usuario prosumer. El usuario prosumer se caracteriza por utilizar su teléfono móvil para crear, proveer y ejecutar servicios. Este nuevo modelo de usuario contribuye al avance de la sociedad de la información, ya que el usuario prosumer se transforma de creador de contenidos a creador de servicios (estos últimos formados por contenidos y la lógica para acceder a ellos, procesarlos y representarlos). El objetivo general de este trabajo de Tesis es la provisión de un modelo de creación, distribución y ejecución de servicios para entorno móvil que permita a los usuarios no programadores (usuarios prosumer), pero expertos en un determinado dominio, crear y ejecutar sus propias aplicaciones y servicios. Para ello se definen, desarrollan e implementan metodologías, procesos, algoritmos y mecanismos adaptables a dominios específicos, para construir entornos de ejecución distribuida de servicios móviles para usuarios prosumer. La provisión de herramientas de creación adaptadas a usuarios no expertos es una tendencia actual que está siendo desarrollada en distintos trabajos de investigación. Sin embargo, no se ha propuesto una metodología de desarrollo de servicios que involucre al usuario prosumer en el proceso de diseño, desarrollo, implementación y validación de servicios. Este trabajo de Tesis realiza un estudio de las metodologías y tecnologías más innovadoras relacionadas con la co‐creación y utiliza este análisis para definir y validar una metodología que habilita al usuario para ser el responsable de la creación de servicios finales. Siendo los entornos móviles prosumer (mobile prosumer environments) una particularización de los entornos de ejecución distribuida de servicios móviles, en este trabajo se tesis se investiga en técnicas de adaptación, distribución, coordinación de servicios y acceso a recursos identificando como requisitos las problemáticas de este tipo de entornos y las características de los usuarios que participan en los mismos. Se contribuye a la adaptación de servicios definiendo un modelo de variabilidad que soporte la interdependencia entre las decisiones de personalización de los usuarios, incorporando mecanismos de guiado y detección de errores. La distribución de servicios se implementa utilizando técnicas de descomposición en árbol SPQR, cuantificando el impacto de separar cualquier servicio en distintos dominios. Considerando el plano de comunicaciones para la coordinación en la ejecución de servicios distribuidos hemos identificado varias problemáticas, como las pérdidas de enlace, conexiones, desconexiones y descubrimiento de participantes, que resolvemos utilizando técnicas de diseminación basadas en publicación subscripción y algoritmos Gossip. Para lograr una ejecución flexible de servicios distribuidos en entorno móvil, soportamos la adaptación a cambios en la disponibilidad de los recursos, proporcionando una infraestructura de comunicaciones para el acceso uniforme y eficiente a recursos. Se han realizado validaciones experimentales para evaluar la viabilidad de las soluciones propuestas, definiendo escenarios de aplicación relevantes (el nuevo universo inteligente, prosumerización de servicios en entornos hospitalarios y emergencias en la web de la cosas). Abstract This Thesis work is developed in the framework of distributed execution of mobile services and contributes to the definition and development of the concept of prosumer user. The prosumer user is characterized by using his mobile phone to create, provide and execute services. This new user model contributes to the advancement of the information society, as the prosumer is transformed from producer of content, to producer of services (consisting of content and logic to access them, process them and represent them). The overall goal of this Thesis work is to provide a model for creation, distribution and execution of services for the mobile environment that enables non‐programmers (prosumer users), but experts in a given domain, to create and execute their own applications and services. For this purpose I define, develop and implement methodologies, processes, algorithms and mechanisms, adapted to specific domains, to build distributed environments for the execution of mobile services for prosumer users. The provision of creation tools adapted to non‐expert users is a current trend that is being developed in different research works. However, it has not been proposed a service development methodology involving the prosumer user in the process of design, development, implementation and validation of services. This thesis work studies innovative methodologies and technologies related to the co‐creation and relies on this analysis to define and validate a methodological approach that enables the user to be responsible for creating final services. Being mobile prosumer environments a specific case of environments for distributed execution of mobile services, this Thesis work researches in service adaptation, distribution, coordination and resource access techniques, and identifies as requirements the challenges of such environments and characteristics of the participating users. I contribute to service adaptation by defining a variability model that supports the dependency of user personalization decisions, incorporating guiding and error detection mechanisms. Service distribution is implemented by using decomposition techniques based on SPQR trees, quantifying the impact of separating any service in different domains. Considering the communication level for the coordination of distributed service executions I have identified several problems, such as link losses, connections, disconnections and discovery of participants, which I solve using dissemination techniques based on publish‐subscribe communication models and Gossip algorithms. To achieve a flexible distributed service execution in mobile environments, I support adaptation to changes in the availability of resources, while providing a communication infrastructure for the uniform and efficient access to resources. Experimental validations have been conducted to assess the feasibility of the proposed solutions, defining relevant application scenarios (the new intelligent universe, service prosumerization in hospitals and emergency situations in the web of things).

Balanced scorecard to improve strategic management control at School of Mines and Energy, Universidad Politécnica de Madrid

We studied the situation in Spanish public universities regarding the use of the Balanced Scorecard (BSC), as an instrument of control and strategic management. Also, we studied its application to the School of Mines and Energy at Universidad Politécnica de Madrid. The main advantage of the BSC is that improves the organizational structure of the workplace and the achievement of the objectives that ensure long-term success. First we review the strategy for success used in the Spanish educational system and specifically in the Spanish public universities. Then using the BSC and applying the main strategic lines for the successful management of the School of Mines and Energy at Universidad Politécnica de Madrid. The strategic lines affect all the college groups and the success of the BSC tool is to increase communication between the faculties, personal auxiliary, students and society in general that make up the university. First we performed a SWOT analysis (DAFO in Spanish) there are proposed different perspectives that focus the long-term strategic objectives. The BSC is designed based on the strategic objectives that set the direction through using indicators and initiatives, the goals are achieved up to the programmed schedule. In the perspective of teaching, objectives are set to update facilities and increase partnerships with other universities and businesses, encouraging ongoing training of staff and improved coordination and internal communication. The internal process perspective aims at improving the marketing, the promotion of the international dimension of the school through strategic alliances, better mobility for students and professors and improved teaching and research quality results. It continues with improving the image of the school between customer?s perspective, the quality perceived by students and the loyalty of the teaching staff by retaining talent. Finally, the financial perspective which should contain costs without harming the quality, improving the employability of students and achieve relevant jobs at teaching and research through international measurement standards.

A novel methodology for planning reliable wireless sensor networks

Wireless sensor networks (WSNs) have shown their potentials in various applications, which bring a lot of benefits to users from both research and industrial areas. For many setups, it is envisioned thatWSNs will consist of tens to hundreds of nodes that operate on small batteries. However due to the diversity of the deployed environments and resource constraints on radio communication, sensing ability and energy supply, it is a very challenging issue to plan optimized WSN topology and predict its performance before real deployment. During the network planning phase, the connectivity, coverage, cost, network longevity and service quality should all be considered. Therefore it requires designers coping with comprehensive and interdisciplinary knowledge, including networking, radio engineering, embedded system and so on, in order to efficiently construct a reliable WSN for any specific types of environment. Nowadays there is still a lack of the analysis and experiences to guide WSN designers to efficiently construct WSN topology successfully without many trials. Therefore, simulation is a feasible approach to the quantitative analysis of the performance of wireless sensor networks. However the existing planning algorithms and tools, to some extent, have serious limitations to practically design reliable WSN topology: Only a few of them tackle the 3D deployment issue, and an overwhelming number of works are proposed to place devices in 2D scheme. Without considering the full dimension, the impacts of environment to the performance of WSN are not completely studied, thus the values of evaluated metrics such as connectivity and sensing coverage are not sufficiently accurate to make proper decision. Even fewer planning methods model the sensing coverage and radio propagation by considering the realistic scenario where obstacles exist. Radio signals propagate with multi-path phenomenon in the real world, in which direct paths, reflected paths and diffracted paths contribute to the received signal strength. Besides, obstacles between the path of sensor and objects might block the sensing signals, thus create coverage hole in the application. None of the existing planning algorithms model the network longevity and packet delivery capability properly and practically. They often employ unilateral and unrealistic formulations. The optimization targets are often one-sided in the current works. Without comprehensive evaluation on the important metrics, the performance of planned WSNs can not be reliable and entirely optimized. Modeling of environment is usually time consuming and the cost is very high, while none of the current works figure out any method to model the 3D deployment environment efficiently and accurately. Therefore many researchers are trapped by this issue, and their algorithms can only be evaluated in the same scenario, without the possibility to test the robustness and feasibility for implementations in different environments. In this thesis, we propose a novel planning methodology and an intelligent WSN planning tool to assist WSN designers efficiently planning reliable WSNs. First of all, a new method is proposed to efficiently and automatically model the 3D indoor and outdoor environments. To the best of our knowledge, this is the first time that the advantages of image understanding algorithm are applied to automatically reconstruct 3D outdoor and indoor scenarios for signal propagation and network planning purpose. The experimental results indicate that the proposed methodology is able to accurately recognize different objects from the satellite images of the outdoor target regions and from the scanned floor plan of indoor area. Its mechanism offers users a flexibility to reconstruct different types of environment without any human interaction. Thereby it significantly reduces human efforts, cost and time spent on reconstructing a 3D geographic database and allows WSN designers concentrating on the planning issues. Secondly, an efficient ray-tracing engine is developed to accurately and practically model the radio propagation and sensing signal on the constructed 3D map. The engine contributes on efficiency and accuracy to the estimated results. By using image processing concepts, including the kd-tree space division algorithm and modified polar sweep algorithm, the rays are traced efficiently without detecting all the primitives in the scene. The radio propagation model iv is proposed, which emphasizes not only the materials of obstacles but also their locations along the signal path. The sensing signal of sensor nodes, which is sensitive to the obstacles, is benefit from the ray-tracing algorithm via obstacle detection. The performance of this modelling method is robust and accurate compared with conventional methods, and experimental results imply that this methodology is suitable for both outdoor urban scenes and indoor environments. Moreover, it can be applied to either GSM communication or ZigBee protocol by varying frequency parameter of the radio propagation model. Thirdly, WSN planning method is proposed to tackle the above mentioned challenges and efficiently deploy reliable WSNs. More metrics (connectivity, coverage, cost, lifetime, packet latency and packet drop rate) are modeled more practically compared with other works. Especially 3D ray tracing method is used to model the radio link and sensing signal which are sensitive to the obstruction of obstacles; network routing is constructed by using AODV protocol; the network longevity, packet delay and packet drop rate are obtained via simulating practical events in WSNet simulator, which to the best of our knowledge, is the first time that network simulator is involved in a planning algorithm. Moreover, a multi-objective optimization algorithm is developed to cater for the characteristics of WSNs. The capability of providing multiple optimized solutions simultaneously allows users making their own decisions accordingly, and the results are more comprehensively optimized compared with other state-of-the-art algorithms. iMOST is developed by integrating the introduced algorithms, to assist WSN designers efficiently planning reliable WSNs for different configurations. The abbreviated name iMOST stands for an Intelligent Multi-objective Optimization Sensor network planning Tool. iMOST contributes on: (1) Convenient operation with a user-friendly vision system; (2) Efficient and automatic 3D database reconstruction and fast 3D objects design for both indoor and outdoor environments; (3) It provides multiple multi-objective optimized 3D deployment solutions and allows users to configure the network properties, hence it can adapt to various WSN applications; (4) Deployment solutions in the 3D space and the corresponding evaluated performance are visually presented to users; and (5) The Node Placement Module of iMOST is available online as well as the source code of the other two rebuilt heuristics. Therefore WSN designers will be benefit from v this tool on efficiently constructing environment database, practically and efficiently planning reliable WSNs for both outdoor and indoor applications. With the open source codes, they are also able to compare their developed algorithms with ours to contribute to this academic field. Finally, solid real results are obtained for both indoor and outdoor WSN planning. Deployments have been realized for both indoor and outdoor environments based on the provided planning solutions. The measured results coincide well with the estimated results. The proposed planning algorithm is adaptable according to the WSN designer’s desirability and configuration, and it offers flexibility to plan small and large scale, indoor and outdoor 3D deployments. The thesis is organized in 7 chapters. In Chapter 1, WSN applications and motivations of this work are introduced, the state-of-the-art planning algorithms and tools are reviewed, challenges are stated out and the proposed methodology is briefly introduced. In Chapter 2, the proposed 3D environment reconstruction methodology is introduced and its performance is evaluated for both outdoor and indoor environment. The developed ray-tracing engine and proposed radio propagation modelling method are described in details in Chapter 3, their performances are evaluated in terms of computation efficiency and accuracy. Chapter 4 presents the modelling of important metrics of WSNs and the proposed multi-objective optimization planning algorithm, the performance is compared with the other state-of-the-art planning algorithms. The intelligent WSN planning tool iMOST is described in Chapter 5. RealWSN deployments are prosecuted based on the planned solutions for both indoor and outdoor scenarios, important data are measured and results are analysed in Chapter 6. Chapter 7 concludes the thesis and discusses about future works. vi Resumen en Castellano Las redes de sensores inalámbricas (en inglés Wireless Sensor Networks, WSNs) han demostrado su potencial en diversas aplicaciones que aportan una gran cantidad de beneficios para el campo de la investigación y de la industria. Para muchas configuraciones se prevé que las WSNs consistirán en decenas o cientos de nodos que funcionarán con baterías pequeñas. Sin embargo, debido a la diversidad de los ambientes para desplegar las redes y a las limitaciones de recursos en materia de comunicación de radio, capacidad de detección y suministro de energía, la planificación de la topología de la red y la predicción de su rendimiento es un tema muy difícil de tratar antes de la implementación real. Durante la fase de planificación del despliegue de la red se deben considerar aspectos como la conectividad, la cobertura, el coste, la longevidad de la red y la calidad del servicio. Por lo tanto, requiere de diseñadores con un amplio e interdisciplinario nivel de conocimiento que incluye la creación de redes, la ingeniería de radio y los sistemas embebidos entre otros, con el fin de construir de manera eficiente una WSN confiable para cualquier tipo de entorno. Hoy en día todavía hay una falta de análisis y experiencias que orienten a los diseñadores de WSN para construir las topologías WSN de manera eficiente sin realizar muchas pruebas. Por lo tanto, la simulación es un enfoque viable para el análisis cuantitativo del rendimiento de las redes de sensores inalámbricos. Sin embargo, los algoritmos y herramientas de planificación existentes tienen, en cierta medida, serias limitaciones para diseñar en la práctica una topología fiable de WSN: Sólo unos pocos abordan la cuestión del despliegue 3D mientras que existe una gran cantidad de trabajos que colocan los dispositivos en 2D. Si no se analiza la dimensión completa (3D), los efectos del entorno en el desempeño de WSN no se estudian por completo, por lo que los valores de los parámetros evaluados, como la conectividad y la cobertura de detección, no son lo suficientemente precisos para tomar la decisión correcta. Aún en menor medida los métodos de planificación modelan la cobertura de los sensores y la propagación de la señal de radio teniendo en cuenta un escenario realista donde existan obstáculos. Las señales de radio en el mundo real siguen una propagación multicamino, en la que los caminos directos, los caminos reflejados y los caminos difractados contribuyen a la intensidad de la señal recibida. Además, los obstáculos entre el recorrido del sensor y los objetos pueden bloquear las señales de detección y por lo tanto crear áreas sin cobertura en la aplicación. Ninguno de los algoritmos de planificación existentes modelan el tiempo de vida de la red y la capacidad de entrega de paquetes correctamente y prácticamente. A menudo se emplean formulaciones unilaterales y poco realistas. Los objetivos de optimización son a menudo tratados unilateralmente en los trabajos actuales. Sin una evaluación exhaustiva de los parámetros importantes, el rendimiento previsto de las redes inalámbricas de sensores no puede ser fiable y totalmente optimizado. Por lo general, el modelado del entorno conlleva mucho tiempo y tiene un coste muy alto, pero ninguno de los trabajos actuales propone algún método para modelar el entorno de despliegue 3D con eficiencia y precisión. Por lo tanto, muchos investigadores están limitados por este problema y sus algoritmos sólo se pueden evaluar en el mismo escenario, sin la posibilidad de probar la solidez y viabilidad para las implementaciones en diferentes entornos. En esta tesis, se propone una nueva metodología de planificación así como una herramienta inteligente de planificación de redes de sensores inalámbricas para ayudar a los diseñadores a planificar WSNs fiables de una manera eficiente. En primer lugar, se propone un nuevo método para modelar demanera eficiente y automática los ambientes interiores y exteriores en 3D. Según nuestros conocimientos hasta la fecha, esta es la primera vez que las ventajas del algoritmo de _image understanding_se aplican para reconstruir automáticamente los escenarios exteriores e interiores en 3D para analizar la propagación de la señal y viii la planificación de la red. Los resultados experimentales indican que la metodología propuesta es capaz de reconocer con precisión los diferentes objetos presentes en las imágenes satelitales de las regiones objetivo en el exterior y de la planta escaneada en el interior. Su mecanismo ofrece a los usuarios la flexibilidad para reconstruir los diferentes tipos de entornos sin ninguna interacción humana. De este modo se reduce considerablemente el esfuerzo humano, el coste y el tiempo invertido en la reconstrucción de una base de datos geográfica con información 3D, permitiendo así que los diseñadores se concentren en los temas de planificación. En segundo lugar, se ha desarrollado un motor de trazado de rayos (en inglés ray tracing) eficiente para modelar con precisión la propagación de la señal de radio y la señal de los sensores en el mapa 3D construido. El motor contribuye a la eficiencia y la precisión de los resultados estimados. Mediante el uso de los conceptos de procesamiento de imágenes, incluyendo el algoritmo del árbol kd para la división del espacio y el algoritmo _polar sweep_modificado, los rayos se trazan de manera eficiente sin la detección de todas las primitivas en la escena. El modelo de propagación de radio que se propone no sólo considera los materiales de los obstáculos, sino también su ubicación a lo largo de la ruta de señal. La señal de los sensores de los nodos, que es sensible a los obstáculos, se ve beneficiada por la detección de objetos llevada a cabo por el algoritmo de trazado de rayos. El rendimiento de este método de modelado es robusto y preciso en comparación con los métodos convencionales, y los resultados experimentales indican que esta metodología es adecuada tanto para escenas urbanas al aire libre como para ambientes interiores. Por otra parte, se puede aplicar a cualquier comunicación GSM o protocolo ZigBee mediante la variación de la frecuencia del modelo de propagación de radio. En tercer lugar, se propone un método de planificación de WSNs para hacer frente a los desafíos mencionados anteriormente y desplegar redes de sensores fiables de manera eficiente. Se modelan más parámetros (conectividad, cobertura, coste, tiempo de vida, la latencia de paquetes y tasa de caída de paquetes) en comparación con otros trabajos. Especialmente el método de trazado de rayos 3D se utiliza para modelar el enlace de radio y señal de los sensores que son sensibles a la obstrucción de obstáculos; el enrutamiento de la red se construye utilizando el protocolo AODV; la longevidad de la red, retardo de paquetes ix y tasa de abandono de paquetes se obtienen a través de la simulación de eventos prácticos en el simulador WSNet, y según nuestros conocimientos hasta la fecha, es la primera vez que simulador de red está implicado en un algoritmo de planificación. Por otra parte, se ha desarrollado un algoritmo de optimización multi-objetivo para satisfacer las características de las redes inalámbricas de sensores. La capacidad de proporcionar múltiples soluciones optimizadas de forma simultánea permite a los usuarios tomar sus propias decisiones en consecuencia, obteniendo mejores resultados en comparación con otros algoritmos del estado del arte. iMOST se desarrolla mediante la integración de los algoritmos presentados, para ayudar de forma eficiente a los diseñadores en la planificación de WSNs fiables para diferentes configuraciones. El nombre abreviado iMOST (Intelligent Multi-objective Optimization Sensor network planning Tool) representa una herramienta inteligente de planificación de redes de sensores con optimización multi-objetivo. iMOST contribuye en: (1) Operación conveniente con una interfaz de fácil uso, (2) Reconstrucción eficiente y automática de una base de datos con información 3D y diseño rápido de objetos 3D para ambientes interiores y exteriores, (3) Proporciona varias soluciones de despliegue optimizadas para los multi-objetivo en 3D y permite a los usuarios configurar las propiedades de red, por lo que puede adaptarse a diversas aplicaciones de WSN, (4) las soluciones de implementación en el espacio 3D y el correspondiente rendimiento evaluado se presentan visualmente a los usuarios, y (5) El _Node Placement Module_de iMOST está disponible en línea, así como el código fuente de las otras dos heurísticas de planificación. Por lo tanto los diseñadores WSN se beneficiarán de esta herramienta para la construcción eficiente de la base de datos con información del entorno, la planificación práctica y eficiente de WSNs fiables tanto para aplicaciones interiores y exteriores. Con los códigos fuente abiertos, son capaces de comparar sus algoritmos desarrollados con los nuestros para contribuir a este campo académico. Por último, se obtienen resultados reales sólidos tanto para la planificación de WSN en interiores y exteriores. Los despliegues se han realizado tanto para ambientes de interior y como para ambientes de exterior utilizando las soluciones de planificación propuestas. Los resultados medidos coinciden en gran medida con los resultados estimados. El algoritmo de planificación x propuesto se adapta convenientemente al deiseño de redes de sensores inalámbricas, y ofrece flexibilidad para planificar los despliegues 3D a pequeña y gran escala tanto en interiores como en exteriores. La tesis se estructura en 7 capítulos. En el Capítulo 1, se presentan las aplicaciones de WSN y motivaciones de este trabajo, se revisan los algoritmos y herramientas de planificación del estado del arte, se presentan los retos y se describe brevemente la metodología propuesta. En el Capítulo 2, se presenta la metodología de reconstrucción de entornos 3D propuesta y su rendimiento es evaluado tanto para espacios exteriores como para espacios interiores. El motor de trazado de rayos desarrollado y el método de modelado de propagación de radio propuesto se describen en detalle en el Capítulo 3, evaluándose en términos de eficiencia computacional y precisión. En el Capítulo 4 se presenta el modelado de los parámetros importantes de las WSNs y el algoritmo de planificación de optimización multi-objetivo propuesto, el rendimiento se compara con los otros algoritmos de planificación descritos en el estado del arte. La herramienta inteligente de planificación de redes de sensores inalámbricas, iMOST, se describe en el Capítulo 5. En el Capítulo 6 se llevan a cabo despliegues reales de acuerdo a las soluciones previstas para los escenarios interiores y exteriores, se miden los datos importantes y se analizan los resultados. En el Capítulo 7 se concluye la tesis y se discute acerca de los trabajos futuros.

Climate Change and Restoration of Degraded Land

The United Nations Climate Change Conference, Durban 2011, delivered a breakthrough on the international community's response to climate change. In the second largest meeting of its kind, the negotiations advanced, in a balanced fashion, the implementation of the Convention and the Kyoto Protocol, the Bali Action Plan, and the Cancun Agreements. The outcomes included a decision by Parties to adopt a universal legal agreement on climate change as soon as possible, and no later than 2015. One of the decisions adopted by COP 17 and CMP 7 regard to the land use, land-use change and forestry, and invites the Intergovernmental Panel on Climate Change to review and, if necessary, update supplementary methodologies for estimating anthropogenic greenhouse gas emissions by sources and removals by sinks resulting from land use, land-use change and forestry activities under Article 3, paragraphs 3 and 4, of the Kyoto Protocol. Land degradation is a human-induced or natural process which negatively affects the productivity of land within an ecosystem. The direct causes of land degradation are geographically specific. Climate change, including changes in short-term variation, as well as long-term gradual changes in temperature and precipitation, is expected to be an additional stress on rates of land degradation. Book Topics: • Introduction to Climate Change and Land Degradation • Change Mitigation • Climate Change and Waste Land Restoration • Water Management and Planning • Erosion and Hydrological Restoration • Forest Fire Land Restoration • Polluted Soils Restoration • Combating Climate Change by Restoration of Degraded Land • Research Matters – Climate Change Governance • Advanced Statistics Climate Change and Restoration of Degraded Land is of interests to academics, engineers, consultans, designers and professionals involved in restoration of degraded lands projects.

Urbanism and dictatorship: perspectives of the field of urban studies

In 1933 public letter to Wilhelm Furtwängler, Joseph Goebbels synthesized the official understanding of the link between politics, art and society in the early steps of the Third Reich. By assuming the ethos of art, politics acquired a plastic agency to mold its objects —population and the state— as a unified entity in the form of a ‘national-popular community’ (Volksgemeinschaft); in turn, by infusing art with a political valence, it became part of a wider governmental apparatus that reshaped aesthetic discourses and practices. Similar remarks could be made about the ordering of cities and territories in this period. Dictatorial imaginations mobilized urbanism —including urban theory, urban design and planning— as a fundamental tool for social organization. Under their aegis the production of space became a moment in a wider production of society. Many authors suggest that this political-spatial nexus is intrinsic to modernity itself, beyond dictatorial regimes. In this light, I propose to use dictatorial urbanisms as an analytical opportunity to delve into some concealed features of modern urban design and planning. This chapter explores some of these aspects from a theoretical standpoint, focusing on the development of dictatorial planning mentalities and spatial rationalities and drawing links to other historical episodes in order to inscribe the former in a broader genealogy of urbanism. Needless to say, I don’t suggest that we use dictatorships as mere templates to understand modern productions of space. Instead, these cases provide a crude version of some fundamental drives in the operationalization of urbanism as an instrument of social regulation, showing how far the modern imagination of sociospatial orderings can go. Dictatorial urbanisms constituted a set of experiences where many dreams and aspirations of modern planning went to die. But not, as the conventional account would have it, because the former were the antithesis of the latter, but rather because they worked as the excess of a particular orientation of modern spatial governmentalities — namely, their focus on calculation, social engineering and disciplinary spatialities, and their attempt to subsume a wide range of everyday practices under institutional structuration by means of spatial mediations. In my opinion the interest of dictatorial urbanisms lies in their role as key regulatory episodes in a longer history of our urban present. They stand as a threshold between the advent of planning in the late 19th and early 20th century, and its final consolidation as a crucial state instrument after World War II. We need, therefore, to pay attention to these experiences vis-à-vis the alleged ‘normal’ development of the field in contemporary democratic countries in order to develop a full comprehension thereof.

A data-globe and immersive virtual reality environment for upper limb rehabilitation after spinal cord injury

While a number of virtual data-gloves have been used in stroke, there is little evidence about their use in spinal cord injury (SCI). A pilot clinical experience with nine SCI subjects was performed comparing two groups: one carried out a virtual rehabilitation training based on the use of a data glove, CyberTouch combined with traditional rehabilitation, during 30 minutes a day twice a week along two weeks; while the other made only conventional rehabilitation. Furthermore, two functional indexes were developed in order to assess the patient’s performance of the sessions: normalized trajectory lengths and repeatability. While differences between groups were not statistically significant, the data-glove group seemed to obtain better results in the muscle balance and functional parameters, and in the dexterity, coordination and fine grip tests. Related to the indexes that we implemented, normalized trajectory lengths and repeatability, every patient showed an improvement in at least one of the indexes, either along Y-axis trajectory or Z-axis trajectory. This study might be a step in investigating new ways of treatments and objective measures in order to obtain more accurate data about the patient’s evolution, allowing the clinicians to develop rehabilitation treatments, adapted to the abilities and needs of the patients.

Resilence, rural development and suistainable management: a working with people model approach

Nowadays, it has become evident the need to seek sustainable development models that address challenges arising in a variety of contexts. The resilience concept appears connected to the ability of people to cope with adversities that inevitably arise due to context dynamics, at different spatial and temporal scales. This concept is related to the model known as Working With People (WWP), focused on rural development projects planning, management and evaluation, from the integration of three dimensions: technical-entrepreneurial, ethical-social and political-contextual. The research reported is part of the RETHINK European Project, whose overall aim is farm modernization and rural resilience. The resilience concept has been analyzed, in the scope of rural development projects management, and a relationship with the WWP model has been established. To this end, a thorough review of the scientific literature concerning this topic has been addressed, in order to develop the state of the art of the different concepts and models involved. A conceptual proposal for the integration of resilience in rural development projects sustainable management, through the three-dimensional WWP model is presented.