Origin and patterns of distribution of trace elements in street dust. Unleaded petrol and urban lead

The elemental composition, patterns of distribution and possible sources of street dust are not common to all urban environments, but vary according to the peculiarities of each city. The common features and dissimilarities in the origin and nature of street dust were investigated through a series of studies in two widely different cities, Madrid (Spain) and Oslo (Norway), between 1990 and 1994. The most comprehensive sampling campaign was carried out in the Norwegian capital during the summer of 1994. An area of 14 km2, covering most of downtown Oslo and some residential districts to the north of the city, was divided into 1 km2 mapping units, and 16 sampling increments of approximately 150 g were collected from streets and roads in each of them. The fraction below 100 μm was acid-digested and analysed by ICP-MS. Statistical analyses of the results suggest that chemical elements in street dust can be classified into three groups: “urban” elements (Ba, Cd, Co, Cu, Mg, Pb, Sb, Ti, Zn), “natural” elements (Al, Ga, La, Mn, Na, Sr, Th, Y) and elements of a mixed origin or which have undergone geochemical changes from their original sources (Ca, Cs, Fe, Mo, Ni, Rb, Sr, U). Soil resuspension and/or mobilisation appears to be the most important source of “natural” elements, while “urban” elements originate primarily from traffic and from the weathering and corrosion of building materials. The data for Pb seem to prove that the gradual shift from leaded to unleaded petrol as fuel for automobiles has resulted in an almost proportional reduction in the concentration of Pb in dust particles under 100 μm. This fact and the spatial distribution of Pb in the city strongly suggest that lead sources other than traffic (i.e. lead accumulated in urban soil over the years) may contribute as much lead, if not more, to urban street dust.

Crack origin and detection in thin cristallyne solar cells in a production line

In order to reduce cost and make up for the rising price of silicon, silicon wafers are sliced thinner and wider,eading to weaker wafers and increased breakage rates during fabrication process. In this work we have analysed different cracks origins and their effect on wafer’s mechanical strength. To enhance wafer’s strength some etching methods have been tested. Also, we have analysed wafers from different points of an entire standard production process. Mechanical strength of the wafers has been obtained via the four line bending test and detection of cracks has been tested with Resonance Ultrasonic Vibration (RUV) system, developed by the University of South Florida.

Atmospheric and remote sensing surveys evaluated at the natural analogue "Campo de Calatrava" and its relation with isotopic Radon activity and CO2 flux as strategy for CCS projects

C0 capture and storage (CCS) projects are presently developed to reduce the emission of anthropogenic co2 into the atmosphere. CCS technologies are expected to account for the 20% of the C0 reduction by 2050.The results of this paper are referred to the OXYCFB300 Compostilla Project (European Energy Program for Recover). Since the detection and control of potential leakage from storage formation is mandatory in a project of capture and geological storage of C02 (CCS), geophysical , ground deformation and geochemical monitoring have been carried out to detect potentialleakage, and, in the event that this occurs, identify and quantify it. This monitoring needs to be developed prior, during and after the injection stage. For a correct interpretation and quantification of the leakage, it is essential to establish a pre-injection characterization (baseline)of the area affected by the C02 storage at reservoir level as well as at shallow depth, surface and atmosphere, via soil gas measurements.

Nutritive value and protein quality of soybean meals according to origin and crop year

Resultados de la investigación sobre el valor nutritivo y calidad de la proteína de la alimentación basada en soja en función del origen y del año de la recolección.

Optimización del peaje en autopistas interurbanas que compiten con carreteras convencionales libres de pago : una perspectiva de eficiencia y equidad

En algunos países, como por ejemplo España, es común que entre un origen y un destino existan dos carreteras paralelas en las que existen ciertas diferencias. La más importante es que una de las vías es una autopista que ofrece a los usuarios una mayor comodidad y un menor tiempo de viaje a cambio del pago de un peaje, el cual no es necesario abonar en la carretera convencional paralela. Así, el problema de la tarificación vial ha sido estudiado en diversas ocasiones. Existe un amplio consenso en que para lograr el máximo bienestar social, los usuarios deben internalizar las externalidades que producen y no perciben a través de un peaje. Sin embargo, dicho peaje puede perjudicar a los usuarios con bajos ingresos. Dependiendo del objetivo (por ejemplo, maximizar el bienestar, maximizar la equidad social, la amortización de la construcción de la carretera, etc) el peaje óptimo podría variar sustancialmente. La literatura académica acerca de los peajes, la eficiencia y la equidad es vasta y diversa. Sin embargo, hemos encontrado una deficiencia en dicha literatura sobre el peaje óptimo, en corredores donde una carretera y una autopista con diferentes características de calidad compiten para capturar el tráfico. Particularmente no se ha encontrado ninguna investigación acerca del establecimiento del peaje que maximice el bienestar social o la equidad para distintas distribuciones del valor del tiempo de viaje (VTT), caracterizadas por su media y varianza. Por ello, el principal objetivo de la investigación es estimar la influencia que tiene la distribución de la renta de una sociedad sobre el peaje óptimo. La presente tesis doctoral trata de obtener, por medio de una metodología robusta, las diferentes políticas de peajes que los planificadores de transporte deberían llevar a cabo según la riqueza y cohesión social de los potenciales usuarios del corredor, la demanda y el objetivo que se busque con dicha tarificación, esto es, maximizar el bienestar social o la equidad. Adicionalmente también se obtienen los peajes óptimos dependiendo de si el corredor se encuentra totalmente tarificado o únicamente se debe pagar un peaje por circular en la autopista. In some countries, such as Spain, it is very common that in the same corridor there are two roads with the same origin and destination but with some differences. The most important contrast is that one is a toll highway which offers a better quality than the parallel road in exchange of a price. The users decide if the price of the toll worth to pay for the advantages offered. The problem of road pricing has been largely studied. It is well acknowledged that in order to achieve the maximum social welfare, users must internalize the externalities they produce and do not perceive through a toll. However, that toll can harm users with low income. Depending on the objective (e.g. maximize welfare, maximize social equity, amortize the construction of the road, etc) the optimal toll might vary substantially. The academic literature about pricing, efficiency and equity is vast and diverse. However, as far as we have found, there is a gap in the literature regarding the optimal price where a road and a highway with different quality characteristics compete for capturing the traffic in a corridor. Particularly we did not find any research estimating the optimal welfare price or the optimal equity price for different Value of Travel Time (VTT) distributions characterized by different VTT average and variance. The objective of the research is to fill this gap. In this research a theoretical model in order to obtain the optimal price in a toll highway that competes for capturing the traffic with a conventional road is developed. This model is done from the welfare and equity perspective and for non‐usual users who decide over the expectation of free flow conditions. The model is finally applied to the variables we want to focus on: average value of travel time (VTT) which is strongly related with income, dispersion of this VTT, different kind of distributions of VTT and traffic levels, from free flow to congestion. Furthermore, we also obtain the optimal tolls with the corridor completely charged or with untolled alternative.

How varies optimal welfare pricing with income distribution? The case of the untolled alternative.

In some countries, such as Spain, it is very common that in the same corridor there are two roads with the same origin and destination but with some differences. The most important contrast is that one is a toll highway which offers a better quality than the parallel road in exchange of a price. The users decide if the price of the toll is worth to pay for the advantages offered. This problem is known as the untolled alternative and it has been largely studied in the academic literature, particularly related to economic efficiency and the optimal welfare toll. However, there is a gap in the literature academic regarding how it affects income distribution to the optimal toll. The main objective of the paper is to fill this gap. In this paper a theoretical model in order to obtain the optimal welfare price in a toll highway that competes for capturing the traffic with a conventional road is developed. This model is done for non-usual users who decide over the expectation of free flow conditions. This model is finally applied to the variables we want to focus on: average value of travel time (VTT) which is strongly related with income, dispersion of this VTT and traffic levels, from free flow to congestion. Derived from the results, we conclude that the higher the average VTT the higher the optimal price, the higher the dispersion of this VTT the lower the optimal price and finally, the more the traffic the higher the optimal toll.

How varies optimal welfare pricing with income distribution? The case of the untolled alternative

In some countries, such as Spain, it is very common that in the same corridor there are two roads with the same origin and destination but with some differences. The most important contrast is that one is a toll highway which offers a better quality than the parallel road in exchange of a price. The users decide if the price of the toll is worth paying for the advantages offered. This problem is known as the untolled alternative and it has been largely studied in the academic literature, particularly related to economic efficiency and the optimal welfare toll. However, there is a gap in the academic literature regarding how income distribution affects the optimal toll. The main objective of the paper is to fill this gap. In this paper a theoretical model is developed in order to obtain the optimal welfare price in a toll highway that competes with a conventional road for capturing the traffic. This model is done for non-usual users who decide over the expectation of free flow conditions. This model is finally applied to the variables we want to focus on: average value of travel time (VTT) which is strongly related with income, dispersion of this VTT and traffic levels, from free flow to congestion. Derived from the results, we conclude that the higher the average VTT the higher the optimal price, the higher the dispersion of this VTT the lower the optimal price and finally, the more the traffic the higher the optimal toll

Key factors affecting the efficiency of transport interchanges

This paper provides a meta-analysis of long/short distance passenger interconnectivity within the European context. The analysis is based on the results of the European project HERMES of the 7th EU R&D Programme. The study collected stakeholders and travelers’ valuation and preferences in 5 interchanges in 3 EU countries. To that end a common survey was conducted in the following sites: Gothenburg Central Station (Sweden), Avenida de America Interchange in Madrid, Lleida-Zaragoza railway stations (Spain), and the Intermodal Station of Part Dieu in Lyon (France). The first survey addresses the analysis of the different stakeholders’ opinion on the interchange management and characteristics. The second survey gives an insight into the key requirements of long/short distance intermodal passengers in the selected case studies. This included the following aspects: on one hand, trip origin and destination, connecting transport services and modes, trip characteristics, type of ticket, trip motive and socioeconomic characteristics of the traveller. On the other hand, it was structured in such a way to ask passengers to rate importance/satisfaction of a series of common quality and functional aspects like information, accessibility, transfer times, service supply, etc. In conclusion, the paper highlights which elements of the interchange are considered as relevant and how different groups of stakeholders value them, both theoretically and in the selected case studies. They also have identified some key barriers as the lack of internal coordination among operators, managers and decision makers, as well as the the poor signage, particularly among connecting services. Travellers seem to have different priorities depending on their age, purpose of trip and mode chosen. In some cases time appears as the most relevant factor, whilst price is decisive in others.

Energías renovables en el sistema marítimo portuario : aprovechamiento energétio de los molinos de marea

Desde el siglo VIII hasta prácticamente el siglo XX, los molinos de marea han sido una fuente de desarrollo de las zonas en las que estaban implantados. En toda la costa atlántica de Europa, y posteriormente en América, se desarrollaron estos ingenios conectados por su naturaleza con los puertos. En ellos se procesaban materia prima que tenía su origen o destino en dichos puertos. La aparición de otras fuentes de energía más económicas y eficaces supuso la decadencia paulatina de estos ingenios, hasta la práctica desaparición de un buen número de ellos. En los últimos años, tanto instituciones privadas como públicas, especialmente ayuntamientos han mostrado un interés en conservar estos ingenios ya sea como edificación singular en el que se desarrollen distintos negocios, o como museos o “centros de interpretación” en los que se explica el funcionamiento del molino y su relación con la comarca de influencia. Este nuevo interés por el tema, unido a la necesidad de buscar nuevas fuentes de energías renovables para dar cumplimento a las condiciones del Tratado de Kyoto motivan la necesidad de un estudio de la aplicación de la energía minihidráulica a los antiguos molinos. En el presente documento se ha procedido en primer lugar a describir la historia de los molinos de marea y a continuación a localizarlos en cada provincia para identificar los posibles puntos de producción de energía. Seguidamente se procedió a identificar los diferentes tipos de turbinas aplicables a estos casos, de los que se han elegido dos de ellos, uno de ellos consolidado y el otro en fase experimental, para determinar y analizar la tendencia de determinadas magnitudes financieras en función de la carrera de marea. Las conclusiones resultantes de este análisis han sido que el sistema de funcionamiento mediante el flujo de la marea es menos productivo que mediante reflujo y que la altura de marea en las costas españolas limita considerablemente la rentabilidad de la inversión. Esta circunstancia obliga a hacer un estudio de viabilidad muy detallado de cada uno de los casos. Las investigaciones futuras en este campo se deben encaminar hacia el desarrollo de un nuevo tipo de miniturbina con una mayor regulación para obtener un mayor rendimiento, teniendo en cuenta, además, que el estuario de un molino de marea puede ser además un excelente banco de pruebas. Por otro lado, la posible producción de energía puede ser un elemento a estudiar dentro de un sistema de generación distribuida en el ámbito de una smart-city. From the eighth century until practically the twentieth century, the tide mills have been a source of development of the areas in which they were implanted. Across the Atlantic coast of Europe, and subsequently in America, these devices were developed and connected by its nature with the nearby ports. In these places the raw material, with its origin and destination from these ports, were processed. The emergence of other sources of energy more economic and efficient caused the gradual decline of these devices which led to the disappearance of a large number of them. In recent years, both private and public institutions, especially municipalities, have shown interest in preserving these devices as singular buildings, or as museums or "visitor centers" where the process of milling is explained and also its relationship with the region of influence. This renewed interest in the subject, coupled with the need of finding new sources of renewable energy in order to comply with the conditions of the Kyoto Treaty, has created the need for a study of the possible implementation of small hydro power in the old mills. In the present document, first we have proceeded to describe the history of the tide mills and afterwards we have located them in the Spanish provinces to identify the possible locations of energy generation. In the next step, we proceeded to identify the different types of turbines suitable to these cases, and we have been selected two of them. The first one is consolidated and the second one is in an experimental phase. With these pair of turbines we have determined and analyzed the outcome of certain financial data depending on the tidal range. The conclusions drawn from this analysis are that operating the system by the flow tide is less productive than by ebb tide. The limited height of tide in the Spanish coast considerably limits the return on investment. This outcome forces potential investors to make a very detailed analysis of each case study. Future researches in this field should be guided towards the development of a new type of mini turbine with more regulation for a higher performance, taking into account also that the basin of a tidal mill can also be an excellent test place. Furthermore, the potential energy output can be a factor to consider in a distributed generation system within a smart city.

Investigations on the distribution of air transport traffic and CO2 emissions within the European Union

This study analyses the structure of air traffic and its distribution among the different countries in the European Union, as well as traffic with an origin or destination in non-EU countries. Data sources are Eurostat statistics and actual flight information from EUROCONTROL. Relevant variables such as the number of flights, passengers or cargo tonnes and production indicators (RPKs) are used together with fuel consumption and CO2 emissions data. The segmentation of air traffic in terms of distance permits an assessment of air transport competition with surface transport modes. The results show a clear concentration of traffic in the five larger countries (France, Germany, Italy, Spain and UK), in terms of RPKs. In terms of distance the segment between 500 and 1000 km in the EU, has more flights, passengers, RTKs and CO2 emissions than larger distances. On the environmental side, the distribution of CO2 emissions within the EU Member States is presented, together with fuel efficiency parameters. In general, a direct relationship between RPKs and CO2 emissions is observed for all countries and all distance bands. Consideration is given to the uptake of alternative fuels. Segmenting CO2 emissions per distance band and aircraft type reveals which flights contribute the most the overall EU CO2 emissions. Finally, projections for future CO2 emissions are estimated, according to three different air traffic growth and biofuel introduction scenarios.

Planning and Management of Mobility in Natural Protected Areas

The paper describes some relevant results of an on-going research aiming to elaborate a methodology to help the mobility management in natural parks, compatible with their protection missions: it has been developed a procedure to reproduce the mobility-environment relationships in various operational conditions. The final purpose is the identification of: a) the effects of various choices in transport planning, both at long term and strategic level; b) the most effective policies of mobility management. The work is articulated in the following steps: 1) definition of protected area on the basis of ecological and socio-economic criteria and legislative constraints; 2) analysis of mobility needs in the protected areas; 3) reconstruction of the state of the art of mobility management in natural parks at European level; 4) analysis of used traffic flows measurement methods; 5) analysis of environmental impacts due to transport systems modelling (air pollution and noise only); 6) identification of mitigation measures to be potentially applied. The whole methodology has been tested and validated on Italian case studies: i) the concerned area has been zoned according to the land-use peculiarities; ii) the local situations of transport infrastructure (roads and parking), services (public transport systems) and rules (traffic regulations) have been mapped with references to physical and functional attributes; iii) the mobility, both systematic and touristic, has been represented in an origin-destination matrix. By means of an assignment model the flows have been distributed and the corresponding average speeds to quantify gaseous and noise emissions was calculated, the criticalities in the reference scenario have been highlighted, as well as some alternative scenarios, including both operational and infrastructural measures have been identified. The comparison between projects and reference scenario allowed the quantification of effects (variation of emissions) for each scenario and a selection of the most effective management actions to be taken.

Planning and management of mobility in natural protected areas

The final purpose is the identification of: a) the effects of various choices in transport planning, both at long term and strategic level; b) the most effective policies of mobility management. The preliminary work was articulated in the following steps: 1) definition of protected area on the basis of ecological and socio-economic criteria and legislative constraints; 2) analysis of mobility needs in the protected areas; 3) reconstruction of the state of the art of mobility management in natural parks at European level; 4) analysis of used traffic flows measurement methods; 5) analysis of environmental impacts due to transport systems modelling (limited to air pollution and noise); 6) identification of mitigation measures to the potentially applied. The whole methodology has been firstly tested on the case study of the National Park of ?Gran Sasso and Monti della Laga? and further validated on the National Park of ?Gargano?, both located Italy: i) the concerned area has been zoned according to the land-use peculiarities; ii) the local situations of transport infrastructure (roads and parking), services (public transport systems) and rules (traffic regulations) have been mapped with references to physical and functional attributes; iii) the mobility, both systematic and touristic, has been synthetically represented in an origin-destination matrix. By means of an assignment model it has been determined the distribution of flows and the corresponding average speeds to quantify gaseous and noise emissions. On this basis the environmental criticalities in the reference scenario have been highlighted, as well as some alternative scenarios including both operational and infrastructural measures have been identified. The comparison between the projects and the reference scenario allowed the quantification of the effects (variation of emissions) for each scenario and a selection of the most effective management actions to be taken.