New data on the ophiolitic VMS deposits of Moeche (Cabo Ortegal Complex, NW Spain)

As a result of the variscan collision, several allochtonous complexes were emplaced on the Iberian margin in Devonian times, among them the Cabo Ortegal Complex comprising the Moeche ophiolitic sequence. Copper has been won from several mines (Piquitos I & II, Barqueira, Maruxa) from disseminated ores and thin massive sulphide layers in the Moeche Unit, a strongly deformed meta-volcanic sequence comprising mainly quartz-chlorite schists and mylonites, which defines the top of the ophiolite. The ores were metamorphosed and strongly deformed under brittle conditions (for pyrite), but their textures are often apparently post-deformational, due to very common solution-transfer processes; they are composed mostly of pyrite and chalcopyrite, with minor sphalerite, pyrrhotite, etc., and with traces of native gold and PGE. The geology, mineralogy, and geochemistry of the orebodies relate closely to VMS of the Cu-Zn (Cyprus) type. Fluid inclusion studies allowed an estimation of metamorphic conditions at pressures of 2/2’5 kb and T 325/350ºC. New determinations using the chlorite geothermometer yield temperatures around 320 ºC, corresponding to pressures near 2 kb according to the isochores deduced from the fluid inclusion study, although in the Barqueira mine higher temperatures, up to 350 ºC, are found, corresponding to presssures up to 2’5 kb. Pb isotopic compositions of pyrite point to a double source of Pb, i.e. a main mantle and a subordinate crustal source. The values for 87SR/86Sr in pyrite support this interpretation, but some results suggest later mobilization in an open system, corresponding to solution-transfer. Age determinations of pyrite deduced from the Pb isotope uranogenic graph, ≈ 480 Ma, do not fit with the metamorphic ages published for the Moeche Unit, and might point to the age of Pb extraction from the mantle.

Improved ore processing assessed by digital image análisis of the ores: a key to the sustainable development of the Iberian Pyrite Belt

Mining in the Iberian Pyrite Belt (IPB), the biggest VMS metallogenetic province known in the world to date, has to face a deep crisis in spite of the huge reserves still known after ≈5 000 years of production. This is due to several factors, as the difficult processing of complex Cu-Pb-Zn-Ag- Au ores, the exhaustion of the oxidation zone orebodies (the richest for gold, in gossan), the scarce demand for sulphuric acid in the world market, and harder environmental regulations. Of these factors, only the first and the last mentioned can be addressed by local ore geologists. A reactivation of mining can therefore only be achieved by an improved and more efficient ore processing, under the constraint of strict environmental controls. Digital image analysis of the ores, coupled to reflected light microscopy, provides a quantified and reliable mineralogical and textural characterization of the ores. The automation of the procedure for the first time furnishes the process engineers with real-time information, to improve the process and to preclude or control pollution; it can be applied to metallurgical tailings as well. This is shown by some examples of the IPB.

Extensive boiling as a precipitation mechanism for precious and base metal ores, Bienaventurada Mine, Huancavelica, Perú

The Bienaventurada mine operates a polymetallic Ag-Pb-Zn (Cu, Au) vein system of the low sulphidation epithermal type. Fluid inclusions, FI, are abundant in quartz, sphalerite and adularia. FI petrography demonstrates typical primary growth zoning which occurs frequently in crystalline quartz, and defines the most common primary FI. These are usually very small, but several types of primary, P, and secondary, S, FI Assemblages (FIAs) comprising FI of measurable size (3 to > 100 μm) can also be identified through careful petrographic work. The fluids are aqueous and undersaturated, and no evidence of CO2 was found; the degree of fill is usually high (~70-80 %) in the L-rich inclusions, but extremely low in V-rich inclusions. The measured microthermometric values are very consistent in the FIAs selected; they are for the most part roughly similar in the P and S assemblages: the median is typically ~258ºC for total homogenization temperatures, Th, and -1.5 ºC for ice melting temperatures, Tm (corresponding to 2.57 wt% NaCl eq). The widespread occurrence of L-rich and V-rich FI in the same FIA and the consistent Th values point to an extensive boiling system along the vein. In these conditions, Th equals T of trapping, and the ores are assumed to have been precipitated from an aqueous low salinity boiling fluid, of likely meteoric origin, at some 250-280º C, under ~500 m hydrostatic head.

Caracterización automatizada de texturas de menas mediante análisis digital de imagen para su aplicación geometalúrgica

La mineralogía de procesos se ha convertido en los últimos años en una herramienta indispensable dentro del ámbito minero-metalúrgico debido fundamentalmente a la emergencia de la Geometalurgia. Esta disciplina en auge, a través de la integración de datos geológicos, mineros y metalúrgicos, proporciona la información necesaria para que el circuito de concentración mineral pueda responder de manera rápida y eficaz a la variabilidad mineralógica inherente a la geología del yacimiento. Para la generación del modelo geometalúrgico, la mineralogía de procesos debe aportar datos cuantitativos sobre los rasgos mineralógicos influyentes en el comportamiento de los minerales y para ello se apoya en el uso de sistemas de análisis mineralógico automatizado. Estos sistemas son capaces de proporcionar gran cantidad de datos mineralógicos de manera rápida y precisa. Sin embargo, cuando se trata de la caracterización de la textura, el mineralogista debe recurrir a descripciones cualitativas basadas en la observación, ya que los sistemas actuales no ofrecen información textural automatizada. Esta tesis doctoral surge precisamente para proporcionar de manera sistemática información textural relevante para los procesos de concentración mineral. La tesis tiene como objetivo principal la identificación y caracterización del tipo de intercrecimiento que un determinado mineral presenta en las partículas minerales, e inicialmente se han tenido en cuenta los siete tipos de intercrecimiento considerados como los más relevantes bajo el punto de vista del comportamiento de las partículas minerales durante flotación, lixiviación y molienda. Para alcanzar este objetivo se ha desarrollado una metodología basada en el diseño y cálculo de una serie de índices numéricos, a los que se ha llamado índices mineralúrgicos, que cumplen una doble función: por un lado, cada índice aporta información relevante para caracterizar los principales rasgos mineralógicos que gobiernan el comportamiento de las partículas minerales a lo largo de los procesos de concentración y por otro lado, estos índices sirven como variables discriminantes para identificar el tipo de intercrecimiento mineral mediante la aplicación de Análisis Discriminante. Dentro del conjunto de índices propuestos en este trabajo, se han considerado algunos índices propuestos por otros autores para su aplicación tanto en el ámbito de la mineralogía como en otros ámbitos de la ciencia de materiales. Se trata del Índice de Contigüidad (Gurland, 1958), Índice de Intercrecimiento (Amstutz y Giger, 1972) e Índice de Coordinación (Jeulin, 1981), adaptados en este caso para el análisis de partículas minerales. El diseño de los índices se ha basado en los principios básicos de la Estereología y el análisis digital de imagen, y su cálculo se ha llevado a cabo aplicando el método de interceptos lineales mediante la programación en MATLAB de varias rutinas. Este método estereológico permite recoger una serie de medidas a partir de las que es posible calcular varios parámetros, tanto estereológicos como geométricos, que han servido de base para calcular los índices mineralúrgicos. Para evaluar la capacidad discriminatoria de los índices mineralúrgicos se han seleccionado 200 casos en los que se puede reconocer de manera clara alguno de los siete tipos de intercrecimiento considerados inicialmente en este trabajo. Para cada uno de estos casos se han calculado los índices mineralúrgicos y se ha aplicado Análisis Discriminante, obteniendo un porcentaje de acierto en la clasificación del 95%. Esta cifra indica que los índices propuestos son discriminadores fiables del tipo de intercrecimiento. Una vez probada la capacidad discriminatoria de los índices, la metodología desarrollada ha sido aplicada para caracterizar una muestra de un concentrado de cobre procedente de la mina Kansanshi (Zambia). Esta caracterización se ha llevado a cabo para obtener la distribución de calcopirita según su tipo de intercrecimiento. La utilidad de esta distribución ha sido analizada bajo diferentes puntos de vista y en todos ellos los índices mineralúrgicos aportan información valiosa para caracterizar el comportamiento mineralúrgico de las partículas minerales. Los resultados derivados tanto del Análisis Discriminante como de la caracterización del concentrado de Kansanshi muestran la fiabilidad, utilidad y versatilidad de la metodología desarrollada, por lo que su integración como herramienta rutinaria en los sistemas actuales de análisis mineralógico pondría a disposición del mineralurgista gran cantidad de información textural complementaria a la información ofrecida por las técnicas actuales de caracterización mineralógica. ABSTRACT Process mineralogy has become in the last decades an essential tool in the mining and metallurgical sphere, especially driven by the emergence of Geometallurgy. This emergent discipline provides required information to efficiently tailor the circuit performance to the mineralogical variability inherent to ore deposits. To contribute to the Geometallurgical model, process mineralogy must provide quantitative data about the main mineralogical features implied in the minerallurgical behaviour of minerals. To address this characterisation, process mineralogy relies on automated systems. These systems are capable of providing a large amount of data quickly and accurately. However, when it comes to the characterisation of texture, mineralogists need to turn to qualitative descriptions based on observation, due to the fact that current systems can not offer quantitative textural information in a routine way. Aiming at the automated characterisation of textural information, this doctoral thesis arises to provide textural information relevant for concentration processes in a systematic way. The main objective of the thesis is the automated identification and characterisation of intergrowth types in mineral particles. Initially, the seven intergrowth types most relevant for flotation, leaching and grinding are considered. To achieve this goal, a methodology has been developed based on the computation of a set of numerical indices, which have been called minerallurgical indices. These indices have been designed with two main purposes: on the one hand, each index provides information to characterise the main mineralogical features which determine particle behaviour during concentration processes and, on the other hand, these indices are used as discriminant variables for identifying the intergrowth type by Discriminant Analysis. Along with the indices developed in this work, three indices proposed by other authors belonging to different fields of materials science have been also considered after being adapted to the analysis of mineral particles. These indices are Contiguity Index (Gurland, 1958), Intergrowth Index (Amstutz and Giger, 1972) and Coordination Index (Jeulin, 1981). The design of minerallurgical indices is based on the fundamental principles of Stereology and Digital Image Analysis. Their computation has been carried out using the linear intercepts method, implemented by means of MATLAB programming. This stereological method provides a set of measurements to obtain several parameters, both stereological and geometric. Based on these parameters, minerallurgical indices have been computed. For the assessment of the discriminant capacity of the developed indices, 200 cases have been selected according to their internal structure, so that one of the seven intergrowth types initially considered in this work can be easily recognised in any of their constituents. Minerallurgical indices have been computed for each case and used as discriminant variables. After applying discriminant analysis, 95% of the cases were correctly classified. This result shows that the proposed indices are reliable identifiers of intergrowth type. Once the discriminant power of the indices has been assessed, the developed methodology has been applied to characterise a copper concentrate sample from the Kansanshi copper mine (Zambia). This characterisation has been carried out to quantify the distribution of chalcopyrite with respect to intergrowth types. Different examples of the application of this distribution have been given to test the usefulness of the method. In all of them, the proposed indices provide valuable information to characterise the minerallurgical behaviour of mineral particles. Results derived from both Discriminant Analysis and the characterisation of the Kansanshi concentrate show the reliability, usefulness and versatility of the developed methodology. Therefore, its integration as a routine tool in current systems of automated mineralogical analysis should make available for minerallurgists a great deal of complementary information to treat the ore more efficiently.