Nondestructive quantification of chemical and physical properties of fruits by time-resolved reflectance spectroscopy in the wavelength range 650-1000 nm

Time-resolved reflectance spectroscopy can be used to assess nondestructively the bulk (rather than the superficial) optical properties of highly diffusive media. A fully automated system for time-resolved reflectance spectroscopy was used to evaluate the absorption and the transport scattering spectra of fruits in the red and the near-infrared regions. In particular, data were collected in the range 650-1000 nm from three varieties of apples and from peaches, kiwifruits, and tomatoes. The absorption spectra were usually dominated by the water peak near 970 nm, whereas chlorophyll was detected at 675 nm. For ail species the scattering decreased progressively with increasing wavelength. A best fit to water and chlorophyll absorption line shapes and to Mie theory permitted the estimation of water and chlorophyll content and the average size of scattering centers in the bulls; of intact fruits.

Nondestructive quality evaluation and monitoring of Braeburn apples by Spatially Resolved Spectroscopy.

Contact Spatially Resolved Spectroscopy (SRS) measurements by means of a fiber-optics probe were employed for nondestructive assessment and monitoring of Braeburn apples during shelflife storage. SRS measurements and estimation of optical properties were calibrated and validated by means of liquid optical phantoms with known optical properties and a metamodeling method. The acquired optical properties (absorption and reduced scattering coefficients) for the apples during shelf-life storage were found to provide useful information for nondestructive evaluation of apple quality attributes (firmness and SSC) and for monitoring the changes in their microstructure and chemical composition. On-line SRS measurement was achieved by mounting the SRS probe over a conveyor system

The effect of moisture content on nondestructive probing measurements

When assessing existing timber structures it is not possible to obtain density as the ratio mass/volume, so nondestructive probing methods are used to predict density. As in other nondestructive techniques, moisture content influences measurements. The goal of this paper is to study the influence of timber moisture content on two nondestructive probing techniques (penetration resistance and pullout resistance). 25 large cross section specimens of laricio pine from Spain were measured. The moisture content ranged from 65.1% to 8.3%. Penetration depth decreases and screw withdrawal strength increases when moisture content decreases below the fiber saturation point. There are lineal tendencies in both techniques. No moisture content influence was found in measures above fiber saturation point.

Mealiness Detection in Agricultural Crops: Destructive and Nondestructive Tests: A Review

Mealiness is known as an important internal quality attribute of fruits/vegetables, which has significant influence on consumer purchasing decisions. Mealiness has been a topic of research interest over the past several decades. A number of destructive and nondestructive techniques are introduced for mealiness detection. Nondestructive methods are more interesting because they are rapid, noninvasive, and suitable for real-time purposes. In this review, the concept of mealiness is presented for potato, apple, and peach, followed by an in-depth discussion about applications of destructive and nondestructive techniques developed for mealiness detection. The results suggest the potential of electromagnetic-based techniques for nondestructive mealiness evaluation. Further investigations are in progress to find more appropriate nondestructive techniques as well as cost and performance.

Effects of inspections in small world social networks with different contagion rules

Inspections are used to prevent tax evasion or any other unlawful behavior. ? The effect of inspections depends on the network topology and the contagion rule. ? The network is modeled as a Watts?Strogatz Small World that is tuned from regular to random. ? Two contagion rules are applied: continuous and discontinuous. ? The equilibrium populations of payers and evaders are obtained in terms of these system parameters.

Evaluation of the influence of visual parameters on wave transmission velocity in sawn chestnut timber

Non-destructive, visual evaluation and mechanical testing techniques were used to assess the structural properties of 374 samples of chestnut (Castanea sativa). The principal components method was applied to establish and interpret correlations between variables obtained of modulus of elasticity, bending strength and density. The static modulus of elasticity presented higher correlation values than those obtained using non-destructive methods. Bending strength presented low correlations with the non-destructive parameters, but there was some relation to the different knot ratios defined. The relationship was stronger with the most widely used ratio, CKDR. No significant correlations were observed between any of the variables and density.

In situ acoustic methods to estimate the physical and mechanical aging of oriented strand board

Following the success achieved in previous research projects usin non-destructive methods to estimate the physical and mechanical aging of particle and fibre boards, this paper studies the relationships between aging, physical and mechanical changes, using non-destructive measurements of oriented strand board (OSB). 184 pieces of OSB board from a French source were tested to analyze its actual physical and mechanical properties. The same properties were estimated using acoustic non-destructive methods (ultrasound and stress wave velocity) during a physical laboratory aging test. Measurements were recorded of propagation wave velocity with the sensors aligned, edge to edge, and forming an angle of 45 degrees, with both sensors on the same face of the board. This is because aligned measures are not possible on site. The velocity results are always higher in 45 degree measurements. Given the results of statistical analysis, it can be concluded that there is a strong relationship between acoustic measurements and the decline in physical and mechanical properties of the panels due to aging. The authors propose several models to estimate the physical and mechanical properties of board, as well as their degree of aging. The best results are obtained using ultrasound, although the difference in comparison with the stress wave method is not very significant. A reliable prediction of the degree of deterioration (aging) of board is presented.

Non-destructive methods to estimate physical aging of plywood

This paper studies the relationship between aging, physical changes and the results of non-destructive testing of plywood. 176 pieces of plywood were tested to analyze their actual and estimated density using non-destructive methods (screw withdrawal force and ultrasound wave velocity) during a laboratory aging test. From the results of statistical analysis it can be concluded that there is a strong relationship between the non-destructive measurements carried out, and the decline in the physical properties of the panels due to aging. The authors propose several models to estimate board density. The best results are obtained with ultrasound. A reliable prediction of the degree of deterioration (aging) of board is presented.

Spectral Biomimetic Technique for Wood Classification

Palatal clicks are most interesting for human echolocation. Moreover, these sounds are suitable for other acoustic applications due to their regular mathematical properties and reproducibility. Simple and nondestructive techniques, bioinspired by synthetized pulses whose form reproduces the best features of palatal clicks, can be developed. The use of synthetic palatal pulses also allows detailed studies of the real possibilities of acoustic human echolocation without the problems associated with subjective individual differences. These techniques are being applied to the study of wood. As an example, a comparison of the performance of both natural and synthetic human echolocation to identify three different species of wood is presented. The results show that human echolocation has a vast potential.

Reconocimiento de objetos a partir de imágenes termográficas

La termografía es un método de inspección y diagnóstico basado en la radiación infrarroja que emiten los cuerpos. Permite medir dicha radiación a distancia y sin contacto, obteniendo un termograma o imagen termográfica, objeto de estudio de este proyecto. Todos los cuerpos que se encuentren a una cierta temperatura emiten radiación infrarroja. Sin embargo, para hacer una inspección termográfica hay que tener en cuenta la emisividad de los cuerpos, capacidad que tienen de emitir radiación, ya que ésta no sólo depende de la temperatura del cuerpo, sino también de sus características superficiales. Las herramientas necesarias para conseguir un termograma son principalmente una cámara termográfica y un software que permita su análisis. La cámara percibe la emisión infrarroja de un objeto y lo convierte en una imagen visible, originalmente monocromática. Sin embargo, después es coloreada por la propia cámara o por un software para una interpretación más fácil del termograma. Para obtener estas imágenes termográficas existen varias técnicas, que se diferencian en cómo la energía calorífica se transfiere al cuerpo. Estas técnicas se clasifican en termografía pasiva, activa y vibrotermografía. El método que se utiliza en cada caso depende de las características térmicas del cuerpo, del tipo de defecto a localizar o la resolución espacial de las imágenes, entre otros factores. Para analizar las imágenes y así obtener diagnósticos y detectar defectos, es importante la precisión. Por ello existe un procesado de las imágenes, para minimizar los efectos provocados por causas externas, mejorar la calidad de la imagen y extraer información de las inspecciones realizadas. La termografía es un método de ensayo no destructivo muy flexible y que ofrece muchas ventajas. Por esta razón el campo de aplicación es muy amplio, abarcando desde aplicaciones industriales hasta investigación y desarrollo. Vigilancia y seguridad, ahorro energético, medicina o medio ambiente, son algunos de los campos donde la termografía aportaimportantes beneficios. Este proyecto es un estudio teórico de la termografía, donde se describen detalladamente cada uno de los aspectos mencionados. Concluye con una aplicación práctica, creando una cámara infrarroja a partir de una webcam, y realizando un análisis de las imágenes obtenidas con ella. Con esto se demuestran algunas de las teorías explicadas, así como la posibilidad de reconocer objetos mediante la termografía. Thermography is a method of testing and diagnosis based on the infrared radiation emitted by bodies. It allows to measure this radiation from a distance and with no contact, getting a thermogram or thermal image, object of study of this project. All bodies that are at a certain temperature emit infrared radiation. However, making a thermographic inspection must take into account the emissivity of the body, capability of emitting radiation. This not only depends on the temperature of the body, but also on its surface characteristics. The tools needed to get a thermogram are mainly a thermal imaging camera and software that allows analysis. The camera sees the infrared emission of an object and converts it into a visible image, originally monochrome. However, after it is colored by the camera or software for easier interpretation of thermogram. To obtain these thermal images it exists various techniques, which differ in how heat energy is transferred to the body. These techniques are classified into passive thermography, active and vibrotermografy. The method used in each case depends on the thermal characteristics of the body, the type of defect to locate or spatial resolution of images, among other factors. To analyze the images and obtain diagnoses and defects, accuracy is important. Thus there is a image processing to minimize the effects caused by external causes, improving image quality and extract information from inspections. Thermography is a non-­‐destructive test method very flexible and offers many advantages. So the scope is very wide, ranging from industrial applications to research and development.Surveillance and security, energy saving, environmental or medicine are some of the areas where thermography provides significant benefits. This project is a theoretical study of thermography, which describes in detail each of these aspects. It concludes with a practical application, creating an infrared camera from a webcam, and making an analysis of the images obtained with it. This will demonstrate some of the theories explained as well as the ability to recognize objects by thermography.

Estimación de ahorro por inspección del regulador del mercado energético a las instalaciones de energías renovables

La Administración General del Estado, a través de la Comisión Nacional de la Energía, y en colaboración con los órganos competentes de las Comunidades Autónomas correspondientes, realiza inspecciones periódicas y aleatorias cada año, sobre las instalaciones de generación eléctrica, siguiendo los criterios de elección e indicaciones que la Secretaria General de la Energía del Ministerio de Industria, Turismo y Comercio imponga en cada caso. En este proyecto se analizan las distintas incidencias de las distintas tecnologías estudiadas, así como las consecuencias jurídicas y económicas. También se ofrecen las distintas propuestas de sanción como consecuencia de estas incidencias. El objeto del presente proyecto es el estudio de la reducción de costes al estado si el organismo competente (Comisión Nacional de Energía) liquidase a las diferentes instalaciones en función de las irregularidades detectadas como consecuencia de las inspecciones realizadas durante el plan 2011/2012, así como una estimación de dicho ahorro al extrapolar dichos resultados al total de instalaciones ABSTRACT The Central Government, through the National Energy Commission, in cooperation with the competent bodies of the Autonomous Communities concerned, realizes periodic and random inspections every year on electricity generation facilities, following the criteria of choice and indications that the General Secretary of Energy from the Ministry of Industry, Tourism and Commerce impose in each case. This project analyses the different incidences of the different technologies studied as well as the legal and economic consequences. It is also offered different proposals of sanction as a result of these incidents. The purpose of this project is to study the reduction of costs to the state if the competent agency (CNE) decided to close the different facilities depending on the irregularities as a result of inspections conducted during the plan 2011/2012 and as an estimate of the savings to extrapolate these results to all the facilities.

Non-destructive measurements of the optical properties of apples by means of time-resolved reflectance

Time-resolved reflectance is proposed and effectively used for the nondestructive measurement of the optical properties in apples. The technique is based on the detection of the temporal dispersion of a short laser pulse injected into the probed medium. The time-distribution of re-emitted photons interpreted with a solution of the Diffusion equation yields the mean values of the absorption and reduced scattering coefficients of the medium. The proposed technique proved valuable for the measurement of the absorption and scattering spectra of different varieties of apples. No major variations were observed in the experimental data when the fruit was peeled, proving that the measured optical properties are referred to the pulp. The depth of probed volume was determined to be about 2 cm. Finally, the technique proved capable to follow the change in chlorophyll absorption during storage.

Non-destructive measurements of the optical properties of apples by means of time-resolved reflectance

Time-resolved reflectance is proposed and effectively used for the nondestructive measurement of the optical properties in apples. The technique is based on the detection of the temporal dispersion of a short laser pulse injected into the probed medium. The time-distribution of re-emitted photons interpreted with a solution of the Diffusion equation yields the mean values of the absorption and reduced scattering coefficients of the medium. The proposed technique proved valuable for the measurement of the absorption and scattering spectra of different varieties of apples. No major variations were observed in the experimental data when the fruit was peeled, proving that the measured optical properties are referred to the pulp. The depth of probed volume was determined to be about 2 cm. Finally, the technique proved capable to follow the change in chlorophyll absorption during storage.

Fruit quality sensing:Post-harvest ripeness

Firmness sensing of selected varieties of apples, pears and avocado fruits has been developed using a nondestructive impact technique. In addition to firmness measurements, postharvest ripeness of apples and pears was monitored by spectrophotometric reflectance measurements, and that of avocadoes by Hunter colour measurements. The data obtained from firmness sensing were analyzed by three analytical procedures: principal component, correlation and regression, and stepwise discriminant analysis. A new software was developed to control the impact test, analyse the data, and sort the fruit into specified classes, based on the criteria obtained from a training procedure. Similar procedures were used to analyse the reflectance and colour data. Both sensing systems were able to classify fruits w i th good accuracy.

Análisis del comportamiento en servicio de los puentes de fábrica ante las nuevas condiciones de explotación

Los puentes arco de fábrica representan una parte importante del inventario de puentes en España y en Europa. De aquí, la importancia cuantitativa de estas estructuras y el interés que representa tanto para las Administraciones, organismos públicos y privados como para la sociedad en general, mantener estos puentes en servicio. Para poder alargar su vida útil, aún más si cabe, se plantea imprescindible llevar a cabo una labor de conservación y mantenimiento adecuada. La importancia de la evaluación estructural de los puentes de fábrica se basa en la conveniencia de conocer el comportamiento estructural tanto en condiciones de servicio como en agotamiento. El comportamiento en Estado Límite Último ha sido estudiado en profundidad y como resultado, la seguridad frente a agotamiento ha quedado definida con cierta confianza. Sin embargo, el comportamiento en Estado Límite de Servicio no es tan conocido. Se considera necesaria una revisión del concepto de ELS en puentes arco de fábrica puesto que muchos de ellos, cumpliendo las comprobaciones establecidas para ELU, presentan daños asociados a las actuales condiciones de explotación existentes actuales. El presente trabajo se enmarca dentro de un proyecto que está llevando a cabo la UIC (Union Internationale de Chemins de Fer) desde 2004. El objetivo general del mismo es conocer el comportamiento de los puentes arco de fábrica y mejorar los métodos de evaluación, mantenimiento y reparación existentes. Con este estudio, se pretende contribuir a mejorar la caracterización del comportamiento en servicio de estas estructuras. Para ello se ha realizado un análisis del estado tensional de la bóveda y el relleno estudiando la influencia de la configuración geométrica de los puentes y las propiedades de los materiales que los componen. Entender el funcionamiento de estas estructuras y conocer sus peculiares características ha sido el paso previo al desarrollo del estudio. Para ello, se ha acudido al minucioso trabajo desarrollado por diversos autores, desde los primeros análisis mediante la línea de presiones hasta los actuales métodos basados en elementos finitos. En primer lugar, se ha realizado un estudio paramétrico de diferentes configuraciones geométricas. El objetivo es comprobar la influencia de las dimensiones absolutas y las relaciones existentes entre las mismas en el comportamiento en servicio de los puentes. A continuación, se ha estudiado la influencia de las propiedades mecánicas de los rellenos rígido y granular (modificando su módulo de deformabilidad) en el estado tensional de la bóveda y el propio relleno. Para las dos etapas anteriores se emplea un modelo simplificado de puente arco de fábrica. A continuación, se crea un modelo más completo del mismo, para estudiar la influencia de las propiedades mecánicas del substrato de cimentación en el comportamiento estructural en servicio de la estructura. El objetivo final de este trabajo fin de máster, es conocer el comportamiento en servicio de los puentes arco de fábrica, para poder establecer las variables que condicionan el mismo. El siguiente paso en este campo de estudio, consiste en fijar unos valores límite para las mismas. Como síntesis de las conclusiones obtenidas, se menciona que el comportamiento estructural de los puente arco de fábrica, en mayor o menor medida, está influenciado por su geometría y las propiedades de los rellenos y substrato de cimentación que forman parte del mismo. Masonry arch bridges represent an important part of the total bridges, both in Spain and Europe. For this reason, these structures are so important in terms of quantity. They play an essential role for public administration and people in general. In order to remain those bridges serviceable, suitable inspections and repairs are required. It is necessary to have knowledge of the bridge condition so that an assessment can be made with confidence. It is therefore necessary to check that bridges behave properly under Ultimate Limit State criterion and Serviceability Limit State criterion. ULS has been studied thoroughly and as result, requirements under collapse are well described. However, structural behaviour under conditions of serviceability is not well evaluated. Serviceability Limit State criterion should be redefined for masonry arch bridges assessment. This is because many bridges that fulfil SLS criterion have damages. The purpose of this work is to take part in the improvement of assessment under serviceability. A vault and fill structural behaviour analysis has been performed from two points of view: geometry of the bridge and materials’ properties. The starting point was learning about masonry arch bridges behaviour and their special features. For this task, a revision of several authors’ thorough study has been made, from the line of thrust analysis to the current finite element analysis. Firstly, a parametric study of typologies of bridge has been made. The aim is to know how vault and fill behaviour changes modifying both absolute dimensions and relation between them. In the next step, a study of both surface fill and backfill properties has been done. The aim is to know how vault and fill behaviour changes modifying Young’s modulus. The principal conclusion achieved along this work is that the structural behaviour of masonry bridges depends of the bridge geometry and its material properties.