Noise Figure Measurement of Differential Amplifiers Using non-Ideal Baluns

This paper analyzes the noise and gain measurement of microwave differential amplifiers using two passive baluns. A general model of the baluns is considered, including potential losses and phase/amplitude unbalances. This analysis allows de-embedding the actual gain and noise performance of the isolated amplifier by using single-ended measurements of the cascaded system and baluns. Finally, measured results from two amplifier prototypes are used to validate the theoretical principles.

Sensitivity of a distributed temperature-radiation index melt model based on AWS observations and surface energy balance fluxes, Hurd Peninsula glaciers, Livingston Island, Antarctica

We use an automatic weather station and surface mass balance dataset spanning four melt seasons collected on Hurd Peninsula Glaciers, South Shetland Islands, to investigate the point surface energy balance, to determine the absolute and relative contribution of the various energy fluxes acting on the glacier surface and to estimate the sensitivity of melt to ambient temperature changes. Long-wave incoming radiation is the main energy source for melt, while short-wave radiation is the most important flux controlling the variation of both seasonal and daily mean surface energy balance. Short-wave and long-wave radiation fluxes do, in general, balance each other, resulting in a high correspondence between daily mean net radiation flux and available melt energy flux. We calibrate a distributed melt model driven by air temperature and an expression for the incoming short-wave radiation. The model is calibrated with the data from one of the melt seasons and validated with the data of the three remaining seasons. The model results deviate at most 140 mm w.e. from the corresponding observations using the glaciological method. The model is very sensitive to changes in ambient temperature: a 0.5 ◦ C increase results in 56 % higher melt rates.

Temperature of solar cells with regard to photoactive and non-photoactive light absorption in concentrator PV modules

A new method has recently been proposed by us for accurate measurement of the solar cell temperature in any operational regime, in particular, at a maximum power point (MPP) of the I-V curve (T-p-n(MPP)). For this, fast switching of a cell from MPP to open circuit (OC) regime is carried out and open circuit voltage V-oc is measured immediately (within about 1 millisecond), so that this value becomes to be an indicator of T-p-n(MPP). In the present work, we have considered a practical case, when a solar cell is heated not only by absorption of light incident upon its surface (called "photoactive" absorption of power), but also by heat transferred from structural elements surrounding the cell and heated by absorption of direct or diffused sunlight ("non-photoactive" absorption of power with respect to a solar cell). This process takes place in any concentrator module with non-ideal concentrators. Low overheating temperature of the p-n junction (or p-n junctions in a multijunction cell) is a cumulative parameter characterizing the quality of a solar module by the factor of heat removal effectiveness and, at the same time, by the factor of low "non-photoactive" losses.

Solar driven energy conversion applications based on 3C-SiC

There is a strong and growing worldwide research on exploring renewable energy resources. Solar energy is the most abundant, inexhaustible and clean energy source, but there are profound material challenges to capture, convert and store solar energy. In this work, we explore 3C-SiC as an attractive material towards solar-driven energy conversion applications: (i) Boron doped 3C-SiC as candidate for an intermediate band photovoltaic material, and (ii) 3C-SiC as a photoelectrode for solar-driven water splitting. Absorption spectrum of boron doped 3C-SiC shows a deep energy level at ~0.7 eV above the valence band edge. This indicates that boron doped 3C-SiC may be a good candidate as an intermediate band photovoltaic material, and that bulk like 3C-SiC can have sufficient quality to be a promising electrode for photoelectrochemical water splitting.

Comparison of CO2 From Coal Capture Processes and Valorisation Technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorising CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorise captured CO2. Valorising captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2 capture and valorising will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Comparison of CO2 from coal captureprocesses and valorisation technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorizing CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorizecaptured CO2. Valorizing captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2capture and valorizing will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Pre-Feasibility Study of Hybrid Wind Power-H-2 System Connected to Electrical Grid

The growth of wind power as an electric energy source is profitable from an environmental point of view and improves the energetic independence of countries with little fossil fuel resources. However, the wind resource randomness poses a great challenge in the management of electric grids. This study raises the possibility of using hydrogen as a mean to damp the variability of the wind resource. Thus, it is proposed the use of all the energy produced by a typical wind farm for hydrogen generation, that will in turn be used after for suitable generation of electric energy according to the operation rules in a liberalized electric market.

The use of wind pumps for greenhouse microirrigation: a case study for tomato in Cuba.

Crop irrigation is a major consumer of energy. Only a few countries are self-sufficient in conventional non-renewable energy sources. Fortunately, there are renewable ones, such as wind, which has experienced recent developments in the area of power generation. Wind pumps can play a vital role in irrigation projects in remote farms. A methodology based on daily estimation balance between water needs and water availability was used to evaluate the feasibility of the most economic windmill irrigation system. For this purpose, several factors were included: three-hourly wind velocity (W3 h, m/s), flow supplied by the wind pump as a function of the elevation height (H, m) and daily greenhouse evapotranspiration as a function of crop planting date. Monthly volumes of water required for irrigation (Dr, m3/ha) and in the water tank (Vd, m3), as well as the monthly irrigable area (Ar, ha), were estimated by cumulative deficit water budgeting taking in account these factors. An example is given illustrating the use of this methodology on tomato crop (Lycopersicon esculentum Mill.) under greenhouse at Ciego de Ávila, Cuba. In this case two different W3 h series (average and low wind year), three different H values and five tomato crop planting dates were considered. The results show that the optimum period of wind-pump driven irrigation is with crop plating in November, recommending a 5 m3 volume tank for cultivated areas around 0.2 ha when using wind pumps operating at 15 m of height elevation.

Dual role of HupF in the biosynthesis of [NiFe] hydrogenase in Rhizobium leguminosarum

Background: [NiFe] hydrogenases are enzymes that catalyze the oxidation of hydrogen into protons and electrons, to use H2 as energy source, or the production of hydrogen through proton reduction, as an escape valve for the excess of reduction equivalents in anaerobic metabolism. Biosynthesis of [NiFe] hydrogenases is a complex process that occurs in the cytoplasm, where a number of auxiliary proteins are required to synthesize and insert the metal cofactors into the enzyme structural units. The endosymbiotic bacterium Rhizobium leguminosarum requires the products of eighteen genes (hupSLCDEFGHIJKhypABFCDEX) to synthesize an active hydrogenase. hupF and hupK genes are found only in hydrogenase clusters from bacteria expressing hydrogenase in the presence of oxygen. Results: HupF is a HypC paralogue with a similar predicted structure, except for the C-terminal domain present only in HupF. Deletion of hupF results in the inability to process the hydrogenase large subunit HupL, and also in reduced stability of this subunit when cells are exposed to high oxygen tensions. A ?hupF mutant was fully complemented for hydrogenase activity by a C-terminal deletion derivative under symbiotic, ultra low-oxygen tensions, but only partial complementation was observed in free living cells under higher oxygen tensions (1% or 3%). Co-purification experiments using StrepTag-labelled HupF derivatives and mass spectrometry analysis indicate the existence of a major complex involving HupL and HupF, and a less abundant HupF-HupK complex. Conclusions: The results indicate that HupF has a dual role during hydrogenase biosynthesis: it is required for hydrogenase large subunit processing and it also acts as a chaperone to stabilize HupL when hydrogenase is synthesized in the presence of oxygen.

Magneto-optic current sensor with Faraday mirror for linear birefringence compensation

Fiber optic sensors have some advantages in subjects related with electrical current and magnetic field measurement. In spite of the optical fiber utilization advantages we have to take into account undesirable effects, which are present in real non-ideal optical fibers. In telecommunication and sensor application fields the presence of inherent and induced birefringence is crucial. The presence of birefringence may cause an undesirable change in the polarization state. In order to compensate the linear birefringence a promising method has been chosen. This method employs orthogonal polarization conjugation in the back propagation direction of the light wave in the fiber. A study and a simulation of an experimental setup are realized with the advantage of a significant sensitivity improvement.

Parque eólico Cassino

La energía eólica, así como otras energías renovables, ha experimentado en la última década un gran auge que va extendiéndose alrededor de todo el mundo, cada vez más concienciado de la importancia de las energías renovables como una fuente alternativa de energía. Se han sumado al reto todos los países acogidos al Protocolo de Kyoto, que a fin de reducir emisiones están potenciando la energía eólica como la fuente de energía renovable hoy día más viable para la generación eléctrica. Brasil alcanzó en 2011 los 1.509 MW instalados, lo que representa el 50% de Latinoamérica, seguido por México con el 31%. Las características del sector eléctrico así como un marco legal favorable y el alto potencial eólico, hacen que la perspectiva de crecimiento en este tipo de energía sea muy favorable durante los próximos años, con estimaciones de unos 20.000 MW para 2020. El asentamiento del sector en el país de algunos de los fabricantes más importantes y los avances en cuanto a eficiencia de los aerogeneradores, mayor aprovechamiento de la energía de los vientos menos intensos, amplía las posibles ubicaciones de parques eólicos permitiendo una expansión grande del sector. El parque eólico objeto del proyecto está ubicado en el estado de Rio Grande do Sul, al sur del país, y está constituido por 33 aerogeneradores de 2,0 MW de potencia unitaria, lo que supone una potencia total instalada de 66 MW. La energía eléctrica generada en él será de 272,8 GWh/año. Esta energía se venderá mediante un contrato de compraventa de energía (PPA, Power Purchase Agreement) adjudicado por el gobierno Brasileño en sus sistemas de subasta de energía. En el proyecto se aborda primeramente la selección del emplazamiento del parque eólico a partir de datos de viento de la zona. Estos datos son estudiados para evaluar el potencial eólico y así poder optimizar la ubicación de las turbinas eólicas. Posteriormente se evalúan varios tipos de aerogeneradores para su implantación en el emplazamiento. La elección se realiza teniendo en cuenta las características técnicas de las máquinas y mediante un estudio de la productividad del parque con el aerogenerador correspondiente. Finalmente se opta por el aerogenerador G97-2.0 de GAMESA. La ejecución técnica del parque eólico se realiza de forma que se minimicen los impactos ambientales y de acuerdo a lo establecido en el Estudio de Impacto Ambiental realizado. Este proyecto requiere una inversión de 75,4 M€, financiada externamente en un 80 % y el 20 % con recursos propios del promotor. Del estudio económico-financiero se deduce que el proyecto diseñado es rentable económicamente y viable, tanto desde el punto de vista técnico como financiero. Abstract Wind energy, as well as other renewable energies, has experienced over the last decade a boom that is spreading around the world increasingly aware of the importance of renewable energy as an alternative energy source. All countries that ratified the Kyoto Protocol have joined the challenge promoting wind energy in order to reduce emissions as the more feasible renewable energy for power generation. In 2011 Brazil reached 1509 MW installed, 50% of Latin America, followed by Mexico with 31%. Electric sector characteristics as well as a favorable legal framework and the high wind potential, make the perspective of growth in this kind of energy very positive in the coming years, with estimates of about 20,000 MW by 2020. Some leading manufacturers have settled in the country and improvements in wind turbines efficiency with less intense winds, make higher the number of possible locations for wind farms allowing a major expansion of the sector. The planned wind farm is located in the state of Rio Grande do Sul, in the south of the Brazil, and is made up of 33 wind turbines of 2,0 MW each, representing a total capacity of 66 MW. The electricity generated, 272,8 GWh/year will be sold through a power purchase agreement (PPA) awarded by the Brazilian government in its energy auction systems. The project deals with the site selection of the wind farm from wind data in the area. These data are studied to evaluate the wind potential and thus optimize the location of wind turbines. Then several types of turbines are evaluated for implementation at the site. The choice is made taking into account the technical characteristics of the machines and a study of the productivity of the park with the corresponding turbine. Finally selected wind turbine is Gamesa G97-2.0. The technical implementation of the wind farm is done to minimize environmental impacts as established in the Environmental Impact Study. This project requires an investment of 75,4 M€, financed externally by 80% and 20% with equity from the promoter. The economic-financial study shows that the project is economically viable, both technically and financially.

Compatibilidad de materiales con las mezclas de bioqueroseno de coco, babasú y palmiste con queroseno comercial

Actualmente existe un gran interés por ampliar las fuentes de energías alternativas para aviación y conseguir con ello una reducción de la huella de carbono y de la fuerte dependencia energética de los combustibles fósiles en diferentes países. Por ello, se están llevando a cabo muchos estudios de investigación que tienen por objetivo la conversión de la materia prima vegetal o biomasa en una nueva fuente de energía. Sin embargo, la sustitución exitosa de los combustibles derivados del petróleo por biocombustibles, requiere el cumplimiento de unos requisitos estrictos, y unas propiedades adecuadas. Este proyecto estudia la compatibilidad de materiales con las mezclas de bioqueroseno de coco (CBK20), babasú (BBK20) y palmiste (PBK20), con queroseno comercial Jet A-1 (K-2). Los materiales estudiados son poliméricos, metálicos y composites de aviación que forman parte del sistema combustible del avión. Este estudio pretende demostrar que tanto los materiales utilizados, como los combustibles investigados, son compatibles cuando se encuentran en contacto a cierta temperatura. Para ello, se han comparado sus propiedades siguiendo las normas de referencia establecidas. ABSTRACT Currently there is a strong interest to expand alternative energy sources for aviation and thereby achieve a reduction in carbon footprint and the strong energy dependence on fossil fuels in different countries. It is therefore being carried out many researches based on the conversion of vegetable feedstock in a new energy source. However, a successful replacement of petroleum fuels with biofuels, requires compliance with strict requirements and suitable properties. This project studies the materials compatibility with blends of coconut (CBK20), babassu (BBK20) and palm kernel (PBK20) biokerosene with commercial aviation jet fuel Jet A-1 (K-2). Polymeric and elastomeric materials, metals and aviation composites has been studied as part of the aircraft fuel system. The objective of this study is to demonstrate that both, the tested materials and the fuels investigated, are compatible when they are in contact at a certain temperature. For this reason, materials and kerosene properties have been compared using the standard test methods

Sensor magneto-óptico de corriente con supresión de birrefringencia lineal mediante espejo de Faraday

Fiber optic sensors have some advantages in subjects related with electrical current and magnetic field measurement. In spite of the optical fiber utilization advantages we have to take into account undesirable effects, which are present in real non-ideal optical fibers. In telecommunication and sensor application fields the presence of inherent and induced birefringence is crucial. The presence of birefringence may cause an undesirable change in the polarization state. In order to compensate the linear birefringence a promising method has been chosen. This method employs orthogonal polarization conjugation in the back propagation direction of the light wave in the fiber. A study and a simulation of an experimental setup are realized with the advantage of a significant sensitivity improvement.

Design of a solar incubator. Part 1: Monitoring temperature and enthalpy gradients under commercial production

The real increase in energy prices and the intention of reducing pollutant emissions in developed countries makes interesting to use solar energy in all the processes where its application is possible. As it is demonstrated in countries sited at latitudes with optimal conditions of solar radiation and temperature, it is possible to use solar energy as heat source for small-scale hatchery [1,2], but beyond, making a design for proper installation; it is possible to use solar energy as main or support energy source in medium and large size incubators . Monitoring of a normal actual process using temperature and relative humidity sensors is necessary to know the actual operating conditions that the solar heating system must be designed and sized for. Moreover, the identification and analysis of temperature and enthalpy gradients inside the incubator is of major importance.

Search strategies and the automated control of plant diseases

We propose the use of the "infotaxis" search strategy as the navigation system of a robotic platform, able to search and localize infectious foci by detecting the changes in the profile of volatile organic compounds emitted by and infected plant. We builded a simple and cost effective robot platform that substitutes odour sensors in favour of light sensors and study their robustness and performance under non ideal conditions such as the exitence of obstacles due to land topology or weeds.