Novel method to improve the signal-to-noise ratio in the far-field results obtained from planar near-field measurements

A method to reduce the noise power in far-field pattern without modifying the desired signal is proposed. Therefore, an important signal-to-noise ratio improvement may be achieved. The method is used when the antenna measurement is performed in planar near-field, where the recorded data are assumed to be corrupted with white Gaussian and space-stationary noise, because of the receiver additive noise. Back-propagating the measured field from the scan plane to the antenna under test (AUT) plane, the noise remains white Gaussian and space-stationary, whereas the desired field is theoretically concentrated in the aperture antenna. Thanks to this fact, a spatial filtering may be applied, cancelling the field which is located out of the AUT dimensions and which is only composed by noise. Next, a planar field to far-field transformation is carried out, achieving a great improvement compared to the pattern obtained directly from the measurement. To verify the effectiveness of the method, two examples will be presented using both simulated and measured near-field data.

Thermodynamical Phase Noise in Oscillators Based on L-C Resonators

Using a new Admittance-based model for electrical noise able to handle Fluctuations and Dissipations of electrical energy, we explain the phase noise of oscillators that use feedback around L-C resonators. We show that Fluctuations produce the Line Broadening of their output spectrum around its mean frequency f0 and that the Pedestal of phase noise far from f0 comes from Dissipations modified by the feedback electronics. The charge noise power 4FkT/R C2/s that disturbs the otherwise periodic fluctuation of charge these oscillators aim to sustain in their L-C-R resonator, is what creates their phase noise proportional to Leeson’s noise figure F and to the charge noise power 4kT/R C2/s of their capacitance C that today’s modelling would consider as the current noise density in A2/Hz of their resistance R. Linked with this (A2/Hz?C2/s) equivalence, R becomes a random series in time of discrete chances to Dissipate energy in Thermal Equilibrium (TE) giving a similar series of discrete Conversions of electrical energy into heat when the resonator is out of TE due to the Signal power it handles. Therefore, phase noise reflects the way oscillators sense thermal exchanges of energy with their environment.

Thermodynamical Phase Noise in Oscillators Based on L-C Resonators (Foundations)

Using a new Admittance-based model for electrical noise able to handle Fluctuations and Dissipations of electrical energy, we explain the phase noise of oscillators that use feedback around L-C resonators. We show that Fluctuations produce the Line Broadening of their output spectrum around its mean frequency f0 and that the Pedestal of phase noise far from f0 comes from Dissipations modified by the feedback electronics. The charge noise power 4FkT/R C2/s that disturbs the otherwise periodic fluctuation of charge these oscillators aim to sustain in their L-C-R resonator, is what creates their phase noise proportional to Leeson’s noise figure F and to the charge noise power 4kT/R C2/s of their capacitance C that today’s modelling would consider as the current noise density in A2/Hz of their resistance R. Linked with this (A2/Hz?C2/s) equivalence, R becomes a random series in time of discrete chances to Dissipate energy in Thermal Equilibrium (TE) giving a similar series of discrete Conversions of electrical energy into heat when the resonator is out of TE due to the Signal power it handles. Therefore, phase noise reflects the way oscillators sense thermal exchanges of energy with their environment

A Fluctuation-Dissipation Model for Electrical Noise

This paper shows that today’s modelling of electrical noise as coming from noisy resistances is a non sense one contradicting their nature as systems bearing an electrical noise. We present a new model for electrical noise that including Johnson and Nyquist work also agrees with the Quantum Mechanical description of noisy systems done by Callen and Welton, where electrical energy fluctuates and is dissipated with time. By the two currents the Admittance function links in frequency domain with their common voltage, this new model shows the connection Cause-Effect that exists between Fluctuation and Dissipation of energy in time domain. In spite of its radical departure from today’s belief on electrical noise in resistors, this Complex model for electrical noise is obtained from Nyquist result by basic concepts of Circuit Theory and Thermo- dynamics that also apply to capacitors and inductors.

Influence of road noise disturbances on black vulture nesting area: Case of "Cabeza de Hierro" state in Spanish Mediterranean Central Mountain

The real and potential road influence on soundscape is considered a relevant management aspect that can assess the negative effects of massive visitants on such sensitive species -that have been living for centuries in the area-. As a first approach to the study of human disturbances sound impact, acoustic engineering tools allow us to model noise pollution caused by the main road that crosses the state ?Cabeza de Hierro? (M-604). For these preliminary results we use the French method XPS 31-133, recommend at EU level. Noise emission levels in black vulture nesting area are analyzed to understand the influence of human activities on rural areas and road management on biodiversity conservation. This approach develops a useful tool to make compatible the public enjoyment of forest services such as recreation or landscape scenary, the conservation of biodiversity as well as a suitable social and economic activity level ?timber and firewood harvesting, industry?- at the region.

Revisiting the Classics to recover the Physical Sense in electrical noise

This paper shows a physically cogent model for electrical noise in resistors that has been obtained from Thermodynamical reasons. This new model derived from the works of Johnson and Nyquist also agrees with the Quantum model for noisy systems handled by Callen and Welton in 1951, thus unifying these two Physical viewpoints. This new model is a Complex or 2-D noise model based on an Admittance that considers both Fluctuation and Dissipation of electrical energy to excel the Real or 1-D model in use that only considers Dissipation. By the two orthogonal currents linked with a common voltage noise by an Admittance function, the new model is shown in frequency domain. Its use in time domain allows to see the pitfall behind a paradox of Statistical Mechanics about systems considered as energy-conserving and deterministic on the microscale that are dissipative and unpredictable on the macroscale and also shows how to use properly the Fluctuation-Dissipation Theorem.

Noise Figure Measurement of Differential Amplifiers Using non-Ideal Baluns

This paper analyzes the noise and gain measurement of microwave differential amplifiers using two passive baluns. A general model of the baluns is considered, including potential losses and phase/amplitude unbalances. This analysis allows de-embedding the actual gain and noise performance of the isolated amplifier by using single-ended measurements of the cascaded system and baluns. Finally, measured results from two amplifier prototypes are used to validate the theoretical principles.

Reduction in Calculated Uncertainty of a Noise Map by Improving the Traffic Model Data Through Two Phases

The influence of applying European default traffic values to the making of a noise map was evaluated in a typical environment like Palma de Mallorca. To assess these default traffic values, a first model has been created and compared with measured noise levels. Subsequently a second traffic model, improving the input data used for the first one, has been created and validated according to the deviations. Different methodologies were also examined for collecting model input data that would be of higher quality, by analysing the improvement generated in the reduction in the uncertainty of the noise map introduced by the road traffic noise emission

E-comparisons: A new approach to round robin tests for environmental noise assessment in transport infrastructures

The increasing importance of pollutant noise has led to the creation of many new noise testing laboratories in recent years. For this reason and due to the legal implications that noise reporting may have, it is necessary to create procedures intended to guarantee the quality of the testing and its results. For instance, the ISO/IEC standard 17025:2005 specifies general requirements for the competence of testing laboratories. In this standard, interlaboratory comparisons are one of the main measures that must be applied to guarantee the quality of laboratories when applying specific methodologies for testing. In the specific case of environmental noise, round robin tests are usually difficult to design, as it is difficult to find scenarios that can be available and controlled while the participants carry out the measurements. Monitoring and controlling the factors that can influence the measurements (source emissions, propagation, background noise…) is not usually affordable, so the most extended solution is to create very effortless scenarios, where most of the factors that can have an influence on the results are excluded (sampling, processing of results, background noise, source detection…) The new approach described in this paper only requires the organizer to make actual measurements (or prepare virtual ones). Applying and interpreting a common reference document (standard, regulation…), the participants must analyze these input data independently to provide the results, which will be compared among the participants. The measurement costs are severely reduced for the participants, there is no need to monitor the scenario conditions, and almost any relevant factor can be included in this methodology

Self-adaptive grids for noise mapping refinement

Noise maps are usually represented as contour or isolines maps describing the sound levels in a region. Using this kind of representation the user can easily find the noise level assigned to every location in the map. But the acoustic calculations behind the map are not performed for every single location on it; they are only performed in a grid of receivers. The results in this calculation grid are interpolated to draw the isolines or contours. Therefore, the resolution of the calculation grid and the way it was created (rectangular, triangulated, random…) have an effect on the resulting map. In this paper we describe a smart iterative procedure to optimize the quality of the map at a really low additional computational cost, using self-adaptive grids for the acoustic calculations. These self-adaptive grids add new receivers to the sampling grid in those locations where they are expected to be more useful, so that the performance at the output of the interpolator is enhanced. Self-adaptive sampling grids can be used for minimizing the overall error of the map (improving its quality), or for reducing calculation times, and can be also applied selectively to target areas or contour lines. This can be done by the user customizing the maximum number of iterations, the number of new receivers for each iteration, the target isolines, the target quality…

Effectiveness of resilient wheels in reducing noise and vibrations

This study focuses on the effectiveness of resilient wheels in reducing railway noise and vibrations, and compares the effectiveness of three types of wheels. The finite elements method has been used to characterise the vibratory behaviour of these wheels. The model has been excited with a realistic spectrum of vertical track irregularities, and a spectral analysis has been carried out. Results have been post-processed in order to estimate the sound power emitted. These calculations have been used to assess the effectiveness of the resilient wheel designs in reducing noise emitted to the environment and in propagating structural vibrations.

Comparison of vibration and rolling noise emission of resilient and solid monobloc railway wheels in underground lines

Flat or worn wheels rolling on rough or corrugated tracks can provoke airborne noise and ground-borne vibration, which can be a serious concern for nearby neighbours of urban rail transit lines. Among the various treatments used to reduce vibration and noise, resilient wheels play an important role. In conventional resilient wheels, a slightly prestressed V­shaped rubber ring is mounted between the steel wheel centre and tyre. The elastic layer enhances rolling noise and vibration suppression, as well as impact reduction on the track. In this paper the effectiveness of resilient wheels in underground lines, in comparison to monobloc ones, is assessed. The analysed resilient wheel is able to carry greater loads than standard resilient wheels used for light vehicles. It also presents a greater radial resiliency and a higher axial stiffness than conventional V­wheels. The finite element method was used in this study. A quarter car model was defined, in which the wheelset was modelled as an elastic body. Several simulations were performed in order to assess the vibrational behaviour of elastic wheels, including modal, harmonic and random vibration analysis, the latter allowing the introduction of realistic vertical track irregularities, as well as the influence of the running speed. Due to numerical problems some simplifications were needed. Parametric variations were also performed, in which the sensitivity of the whole system to variations of rubber prestress and Poisson’s ratio of the elastic material was assessed.Results are presented in the frequency domain, showing a better performance of the resilient wheels for frequencies over 200 Hz. This result reveals the ability of the analyzed design to mitigate rolling noise, but not structural vibrations, which are primarily found in the lower frequency range.

New broadband thermal noise primary standard in coaxial technology

A broadband primary standard for thermal noise measurements is presented and its thermal and electromagnetic behavior is analyzed by means of analytical and numerical simulation techniques. It consists of a broadband termination connected to a 3.5mm coaxial airline partially immersed in liquid Nitrogen. The main innovative part of the device is the thermal bead between inner and outer conductors, designed for obtaining a proper thermal contact and to keep low both its contribution to the total thermal noise and its reflectivity. A sensitivity analysis is realized in order to fix the manufacturing tolerances for a proper performance in the range 10MHz¿26.5GHz.

Contribution of the noise radiated by a single vehicle to the road traffic noise

El ruido del tráfico rodado supone aproximadamente la mitad del ruido global ambiental. Las técnicas de control de ruido habitual en emisión (límites de emisión de vehículos) e inmisión (barreras acústicas, doble acristalamiento) no han sido suficientes para disminuir significativamente las molestias por el tráfico rodado en las últimas tres décadas. El efecto positivo de estas técnicas de control ha sido contrarrestado por el aumento de la densidad del tráfico. Por otra parte, la molestia del ruido del tráfico está altamente correlacionada con los niveles máximos de ruido (MNL), producidos por lo general por conductores agresivos. Sin embargo, los sistemas actuales de medición de ruido de tráfico se basan en una valoración global, por lo que no son capaces de discriminar entre los conductores silenciosos y ruidosos. Por lo tanto, en esta tesis se propone un sistema de medida de ruido en el campo cercano, que es capaz de medir la contribución de cada vehículo individual al ruido del tráfico rodado, permitiendo la detección de los conductores ruidosos. Este trabajo describe también una combinación de investigaciones analíticas y experimentales para la identificación de los conductores responsables de la generación de niveles máximos de ruido. El sistema se basa en dos micrófonos embarcados, uno para el ruido del motor y otro para el ruido de rodadura. Con el fin de relacionar estas mediciones de campo cercano con el ruido de los vehículos radiado al campo lejano, se desarrolla un procedimiento completo para la extrapolación del ruido medido por los micrófonos de campo próximo a las posiciones de campo lejano, usando una combinación de predicción analítica y mediciones experimentales. Las correcciones para los niveles extrapolados se deben a factores atmosféricos, al término de divergencia esférica y a las condiciones de absorción de la superficie de propagación. Para el micrófono situado próximo al motor, es necesario también caracterizar las propiedades acústicas del capó del motor. Ambos niveles de ruido se extrapolan de forma independiente a la posición de campo lejano, donde se realiza una comparación entre la predicción y mediciones para confirmar que la metodología es fiable para estimar el impacto a distancia del ruido de tráfico

Analysis of noise temperature sensitivity for the design of a broadband thermal noise primary standard

A broadband primary standard for thermal noise measurements is presented and its thermal and electromagnetic behaviour is analysed by means of a novel hybrid analytical?numerical simulation methodology. The standard consists of a broadband termination connected to a 3.5mm coaxial airline partially immersed in liquid nitrogen and is designed in order to obtain a low reflectivity and a low uncertainty in the noise temperature. A detailed sensitivity analysis is made in order to highlight the critical characteristics that mostly affect the uncertainty in the noise temperature, and also to determine the manufacturing and operation tolerances for a proper performance in the range 10MHz to 26.5 GHz. Aspects such as the thermal bead design, the level of liquid nitrogen or the uncertainties associated with the temperatures, the physical properties of the materials in the standard and the simulation techniques are discussed.