The relationship between soil geochemistry and the bioaccessibility of trace elements in playground soil

A total of 32 samples of surficial soil were collected from 16 playground areas in Madrid (Spain), in order to investigate the importance of the geochemistry of the soil on subsequent bioaccessibility of trace elements. The in vitro bioaccessibility of As, Co, Cr, Cu, Ni, Pb and Zn was evaluated by means of two extraction processes that simulate the gastric environment and one that reproduces a gastric + intestinal digestion sequence. The results of the in vitro bioaccessibility were compared against aqua regia extractions (“total” concentration), and it was found that total concentrations of As, Cu, Pb and Zn were double those of bioaccessible values, whilst that of Cr was ten times higher. Whereas the results of the gastric + intestinal extraction were affected by a high uncertainty, both gastric methods offered very similar and consistent results, with bioaccessibilities following the order: As = Cu = Pb = Zn > Co > Ni > Cr, and ranging from 63 to 7 %. Selected soil properties including pH, organic matter, Fe and CaCO3 content were determined to assess their influence on trace element bioaccessibility, and it was found that Cu, Pb and Zn were predominantly bound to organic matter and, to a lesser extent, Fe oxides. The former fraction was readily accessible in the gastric solution, whereas Fe oxides seemed to recapture negatively charged chloride complexes of these elements in the gastric solution, lowering their bioaccessibility. The homogeneous pH of the playground soils included in the study does not influence trace element bioaccessibility to any significant extent except for Cr, where the very low gastric accessibility seems to be related to the strongly pH-dependent formation of complexes with organic matter. The results for As, which have been previously described and discussed in detail in Mingot et al. (Chemosphere 84: 1386–1391, 2011), indicate a high gastric bioaccessibility for this element as a consequence of its strong association with calcium carbonate and the ease with which these bonds are broken in the gastric solution. The calculation of risk assessments are therefore dependant on the methodology used and the specific environment they address. This has impacts on management strategies formulated to ensure that the most vulnerable of society, children, can live and play without adverse consequences to their health.

Bioaccesibilidad de elementos traza en suelos de parques infantiles. Aplicación al análisis de riesgo

En este trabajo doctoral se evaluó la bioaccesibilidad in vitro para As, Co, Cr, Cu, Ni, Pb y Zn (en la fracción menor de 100μm) por tres procedimientos distintos en 32 muestras de suelo superficial, recogidas en 16 parques infantiles de la ciudad de Madrid.. Dos de los métodos de extracción (SBET y extracción con HCl a pH=1.5) reproducen únicamente la fase gástrica, mientras que otro (RIVM) tiene en cuenta un proceso completo de digestión (gástrico+intestinal). La bioaccesibilidad (%) se definió frente a las concentraciones pseudototales de los elementos traza estudiados (agua regia), utilizando un modelo de regresión lineal pasando por el origen. Los dos métodos gástricos ofrecieron resultados similares y consistentes con datos de otros estudios, siendo el orden de bioaccesibilidad As ≈ Cu ≈ Pb ≈ Zn > Co > Ni > Cr, con rangos entre el 63 y el 7%. Para el procedimiento RIVM (gástrico + intestinal) se obtuvieron valores de un orden similar a los obtenidos en fase gástrica para los elementos As, Cu, Pb y Zn (muy similares para el Zn, algo superiores para Cu y Pb, y algo inferiores para As). Por el contrario, la bioaccesibilidad de Co y Cu es, en este caso, muy superior a la resultante de los ensayos en fase gástrica. El orden de bioaccesibilidad es Co ≈ Cu ≈ Pb > As ≈ Cr ≈ Zn, con rangos entre el 42 y el 69%. Los resultados de los tres procedimientos evaluados correlacionan muy intensamente para los elementos traza As, Cu, Pb y Zn, existiendo intensas correlaciones entre casi todos los elementos estudiados para las dos fases gástricas, no siendo así en el ensayo de digestión completa. Se estudiaron algunas propiedades físico-químicas de los suelos muestreados, así como su composición en algunos elementos mayoritarios con el objeto de evaluar su influencia sobre la bioaccesibilidad. Se observa una dependencia de la bioaccesibilidad (%) de distintos elementos respecto a algunas propiedades de los suelos estudiados, tales como: contenido en Fe, Ca (carbonatos) y P, materia orgánica y pH. El contenido en Fe resulta ser muy relevante en cuanto a la bioaccesibilidad obtenida. En todos los casos correlaciona negativamente con el porcentaje de bioaccesibilidad siendo más significativo este fenómeno en el caso de las extracciones en fase gástrica. Se sugiere que dada la baja solubilización de los óxidos de hierro en los medios extractantes empleados hay una fuerte adsorción de complejos aniónicos (metal-anión cloruro) sobre la superficie de estos óxidos de Fe, con la consiguientes disminución de la bioaccesibilidad. En cuanto al contenido en calcio (carbonatos) este dato parece muy relevante si nos referimos a la bioaccesibilidad del As. Efectivamente el As aparece ligado al Ca del suelo y su solubilización en medios ácidos implicaría un aumento de la bioaccesibilidad del As, mientras que su precipitación al pasar a pH básico (fase intestinal) provocaría una disminución de la bioaccesibilidad. La materia orgánica sólo se ha demostrado relevante respecto a los contenidos pseudototales para el Zn. Para el porcentaje de bioaccesibilidad es significativo para muchos elementos en los ensayos en fase gástrica. La influencia del pH de los suelos estudiados sólo parece ser muy significativo en el caso del Cr. Los valores altamente homogéneos del pH de los suelos estudiados sin duda hacen que este parámetro no resulte significativo para más elementos, tal como se desprende de estudios anteriores. ABSTRACT A total of 32 samples of superficial soil were collected from 16 playground areas in Madrid. The in vitro bioaccessibility of As, Co, Cr, Ni, Pb and Zn (fraction below 100μm) was evaluated by means of three extraction processes. Two of them (SBET and HCl-extraction, pH=1.5) simulate the gastric enviroment, while the other one (RIVM) reproduces a gastric+intestinal digestion sequence. Bioaccessibility (%) was compared against pseudo-total concentrations of trace elements studied (aqua regia) with a linear regression model (forced to intercept the origin) Both gastric methods offered very similar and consistent results with data from other studies, with bioaccessibilities following the order: As ≈ Cu ≈ Pb ≈ Zn > Co > Ni > Cr, and ranging from 63% to 7% The values obtained through RIVM (gastric+ intestinal) method are similar to those obtained in gastric environment for elements: As, Cu, Pb and Zn (very similar to Zn, to a higher extent Cu and Pb, and to a lower extent As). On the contrary the bioaccessibility obtained for elements Co and Cu is considerable higher than in gastric environment sequence. Bioaccessibilities follows the order Co ≈ Cu ≈ Pb >As ≈ Cr ≈ Zn, ranging between 42 and 69%. The three procedures used correlate very intensively to trace elements As,Cu, Pb and Zn, existing strong correlations between almost all elements studied for the two gastric environment, not in the case of the complete digestion sequence. Some soil physical – chemical properties selected were studied, as well as their composition in some main elements in order to assess their influence on bioaccessibility. A dependence was observed between different elements bioaccesibility (%) and some soil properties, such as: Fe, Ca (carbonate) content and P, organic matter and pH. Fe content becomes very relevant regarding the bioaccessibility obtained. In all cases it correlated negatively with bioaccessibility percentage being more significant this phenomenon in gastric environment extractions. It is suggested that given the low solubility of iron oxide in the extractant media used there has to be a strong adsorption of anionic complexes (metal – chloride anion) on these Fe oxides surface, with a consequent decrease of bioaccessibility. Regarding calcium (carbonate) content this data seems very relevant referred to As bioaccessibility. Indeed, As appears to be bound to soil Ca and its solubilisation in acid media would increase As bioaccessibility, while its precipitation at basic pH (intestinal environment) would cause a reduction in bioaccessibility. The influence of organic matter only seemed significant for Zn “total” content, while it is significant in terms of gastric bioaccessibility for many elements. Soil pH only seems to be very significant in case of Cr. The highly homogeneous values for soil pH makes the influence of this parameter negligible for the other elements, unlike what has been observed in several previous studies.

Recubrimientos autolubricantes cuasicristalinos tipo composite depositados mediante proyección térmica para aplicaciones espaciales y de alta temperatura

Los recubrimientos lubricantes sólidos son requeridos para reducir la fricción y prevenir el desgaste en componentes que operan a altas temperaturas o en vacío (vehículos espaciales, industria química, motores diésel, turbinas aeronáuticas y de generación de energía…). Los lubricantes líquidos pierden sus características cuando las condiciones de presión, temperatura o ambientales son severas (oxidación, inestabilidad térmica, volatilidad,…), por ejemplo los aceites minerales convencionales se descomponen a temperaturas próximas a 200 ºC. Por tanto, la única manera de poder conseguir una adecuada lubricación a temperaturas extremas es por medio de sólidos, que cada vez más, se aplican en forma de recubrimientos. Estos recubrimientos podrían ser empleados en componentes de vehículos espaciales reutilizables, donde se pueden alcanzar, en la reentrada en la atmósfera, temperaturas de 700 ºC (bisagras, rodamientos, articulaciones y zonas de sellado en las superficies de control, y rodamientos de las turbobombas y las cajas de engranajes). Dichos recubrimientos también deberían ser capaces de proporcionar una lubricación efectiva a bajas temperaturas para las operaciones en tierra, para las operaciones de arranque en frío, incluso en el espacio. El conjunto de requisitos que tendrían que satisfacer las capas tribológicas relacionadas con estas condiciones extremas es muy diverso, lo que hace que el concepto de capas tipo composite (aquéllas constituidas por varios componentes) sea, en principio, muy adecuado para estas aplicaciones. Recubrimientos composite proyectados térmicamente constituidos por una matriz dura y conteniendo lubricantes sólidos pueden ser una buena solución desde el punto de vista tribológico. El “Lewis Research Centre” de la NASA ha estado desarrollando recubrimientos autolubricantes tipo composite, constituidos por la combinación de materiales duros como el carburo de cromo, junto con lubricantes sólidos como plata o la eutéctica de fluoruros de calcio y bario, en una matriz de NiCr, para su uso en aplicaciones terrestres a alta temperatura. Estos recubrimientos han sido aplicados mediante proyección térmica, siendo denominados como series PS100, PS200, PS300 y PS400, reduciendo de forma significativa el coeficiente de fricción y mejorando la resistencia al desgaste en un amplio margen de temperaturas. Otra nueva familia de materiales con comportamiento tribológico prometedor son las aleaciones cuasicristalinas (QC). Presentan características muy atractivas: alta dureza, baja fricción, alto límite elástico de compresión... Son muy frágiles como materiales másicos, por lo que se intentan aplicar en forma de recubrimientos. Se pueden depositar mediante proyección térmica. Algunos de estos materiales cuasicristalinos, como AlCoFeCr, poseen coeficientes de dilatación próximos al de los materiales metálicos, alta estabilidad térmica, baja conductividad térmica y una elevada resistencia a la oxidación y a la corrosión en caliente. En esta tesis se han desarrollado recubrimientos tipo composite conteniendo cuasicristales como componente antidesgaste, NiCr como componente tenaz, y Ag y la eutéctica de BaF2-CaF2, como lubricantes sólidos. Estos recubrimientos han sido depositados con diferentes composiciones (denominadas TH100, TH103, TH200, TH400, TH600…) mediante distintos procesos de proyección térmica: plasma en aire (PS), plasma en baja presión (LPPS) y combustión a alta velocidad (HVOF). Los recubrimientos se han generado sobre el sustrato X-750, una superaleación base níquel, endurecible por precipitación, con muy buena resistencia mecánica y a la oxidación hasta temperaturas de 870 ºC y, además, es empleada en aplicaciones aeroespaciales e industriales. Los recubrimientos han sido caracterizados microestructuralmente en INTA (Instituto Nacional de Técnica Aeroespacial), mediante SEM-EDS (Scanning Electronic Microscopy-Energy Dispersive Spectroscopy) y XRD (X-Ray Diffraction), y tribológicamente mediante medidas de microdureza y ensayos en tribómetro POD (Pin On Disc) para determinar los coeficientes de fricción y de desgaste. Los recubrimientos han sido ensayados tribológicamente a alta temperatura en INTA y en vacío en AMTTARC (Aerospace and Space Materials Technology Testhouse – Austrian Research Centres), en Seibersdorf (Austria). Se ha estudiado la influencia de la carga normal aplicada, la velocidad lineal y el material del pin. De entre las diferentes series de recubrimientos cuasicristalinos tipo composite desarrolladas, dos de ellas, TH100 y TH103 han presentado una excelente calidad microestructural (baja porosidad, distribución uniforme de fases…) y se han mostrado como excelentes recubrimientos antidesgaste. Sin embargo, estas capas presentan un pobre comportamiento como autolubricantes a temperatura ambiente, aunque mejoran mucho a alta temperatura o en vacío. Los resultados del trabajo presentado en esta tesis han proporcionado nuevo conocimiento respecto al comportamiento tribológico de recubrimientos autolubricantes cuasicristalinos tipo composite depositados por proyección térmica. Sin embargo, dichos resultados, aunque son muy prometedores, no han puesto de manifiesto el adecuado comportamiento autolubricante que se pretendía y, además, como ocurre en cualquier trabajo de investigación, durante el desarrollo del mismo siempre aparecen nuevas dudas por resolver. Se proponen nuevas líneas de trabajo futuro que complementen los resultados obtenidos y que puedan encaminar hacia la obtención de un recubrimiento que mejore su comportamiento autolubricante. ABSTRACT Solid lubricant coatings are required to reduce friction and prevent wear in components that operate at high temperatures or under vacuum (space vehicles, chemical industry, diesel engines, power generation turbines and aeronautical turbines, for instance). In these cases neither greases nor liquid lubricants can be employed and the only practicable approach to lubrication in such conditions is by means of solids. These are increasingly applied in the form of coatings which should exhibit low shear strength, whilst maintaining their chemical stability at extremes temperatures and in the space environment. In the space field, these coatings would be employed in re-usable space plane applications, such as elevon hinges, where temperatures of 700 ºC are reached during re-entry into the Earth’s atmosphere. These coatings should also be capable of providing effective lubrication at lower temperatures since “cold start” operation may be necessary, even in the space environment. The diverse and sometimes conflictive requirements in high temperature and space-related tribological coatings make the concept of composite coatings highly suitable for these applications. Thermal-sprayed composites containing solid lubricants in a hard matrix perform well tribologically. NASA‘s Lewis Research Centre had developed self-lubricating composite coatings for terrestrial use, comprising hard materials like chromium carbide as well as solid lubricant additives such as silver and BaF2-CaF2 eutectic on a Ni-Cr matrix. These coatings series, named PS100, PS200, PS300 and PS400, are applied by thermal spray and significantly reduce friction coefficients, improving wear resistance over a wide temperature range. Quasicrystalline alloys (QC) constitute a new family of materials with promising tribological behaviour. Some QC materials exhibit a combination of adequate antifriction properties: low friction coefficient, high hardness and high yield strength under compression, and can be easily produced as coatings on top of metallic and non-metallic materials. Among these QC alloys, AlCoFeCr has high hardness (700 HV0.1), a thermal expansion coefficient close to that of metals, high thermal stability, low thermal conductivity and good oxidation and hot corrosion resistance. However most QC materials have the disadvantage of being very brittle. In order to take advantage of the excellent tribological properties of QCs, thick composite lubricant coatings were prepared containing them as the hard phase for wear resistance, Ag and BaF2-CaF2 eutectic as lubricating materials and NiCr as the tough component. These coatings were deposited in different composition mixtures (named TH100, TH103, TH200, TH400, TH600…) by different thermal spray processes: air plasma spray (PS), low pressure plasma spray (LPPS) and high velocity oxy-fuel (HVOF), on X-750 substrates. X-750 is an age-hardenable nickel-base superalloy with very good strength and a good resistance to oxidising combustion gas environments at temperatures up to about 870 ºC and it is widely used in aerospace and industrial applications. Coatings have been characterized microstructurally, at INTA (National Institute for Aerospace Technology), by means of SEM-EDS (Scanning Electronic Microscopy- Energy Dispersive Spectroscopy) and XRD (X-Ray Diffraction), and tribologically by microhardness measurements and pin-on-disc testing to determine friction coefficients as well as wear resistance. The coatings were tested tribologically at high temperature at INTA and under vacuum at AMTT-ARC (Aerospace and Space Materials Technology Testhouse – Austrian Research Centres), in Seibersdorf (Austria). Different loads, linear speeds and pin materials were studied. TH100 and TH103 QC alloy matrix composite coatings were deposited by HVOF with excellent microstructural quality (low porosity, uniform phase distribution) and showed to be excellent wear resistant coatings. However these QC alloy matrix composite coatings are poor as a self-lubricant at room temperature but much better at high temperature or in vacuum. The results from the work performed within the scope of this thesis have provided new knowledge concerning the tribological behavior of self-lubricating quasicrystalline composite coatings deposited by thermal spraying. Although these results are very promising, they have not shown an adequate self-lubricating behavior as was intended, and also, as in any research, the results have in addition raised new questions. Future work is suggested to complement the results of this thesis in order to improve the selflubricating behaviour of the coatings.

Thermal effects in Ni/Au and Mo/Au gate metallization AlGaN/GaN HEMT's reliability

AlGaN/GaN high electron mobility transistors (HEMT) are key devices for the next generation of high-power, high-frequency and high-temperature electronics applications. Although significant progress has been recently achieved [1], stability and reliability are still some of the main issues under investigation, particularly at high temperatures [2-3]. Taking into account that the gate contact metallization is one of the weakest points in AlGaN/GaN HEMTs, the reliability of Ni, Mo, Pt and refractory metal gates is crucial [4-6]. This work has been focused on the thermal stress and reliability assessment of AlGaN/GaN HEMTs. After an unbiased storage at 350 o C for 2000 hours, devices with Ni/Au gates exhibited detrimental IDS-VDS degradation in pulsed mode. In contrast, devices with Mo/Au gates showed no degradation after similar storage conditions. Further capacitance-voltage characterization as a function of temperature and frequency revealed two distinct trap-related effects in both kinds of devices. At low frequency (< 1MHz), increased capacitance near the threshold voltage was present at high temperatures and more pronounced for the Ni/Au gate HEMT and as the frequency is lower. Such an anomalous “bump” has been previously related to H-related surface polar charges [7]. This anomalous behavior in the C-V characteristics was also observed in Mo/Au gate HEMTs after 1000 h at a calculated channel temperatures of around from 250 o C (T2) up to 320 ºC (T4), under a DC bias (VDS= 25 V, IDS= 420 mA/mm) (DC-life test). The devices showed a higher “bump” as the channel temperature is higher (Fig. 1). At 1 MHz, the higher C-V curve slope of the Ni/Au gated HEMTs indicated higher trap density than Mo/Au metallization (Fig. 2). These results highlight that temperature is an acceleration factor in the device degradation, in good agreement with [3]. Interface state density analysis is being performed in order to estimate the trap density and activation energy.

Origin and patterns of distribution of trace elements in street dust. Unleaded petrol and urban lead

The elemental composition, patterns of distribution and possible sources of street dust are not common to all urban environments, but vary according to the peculiarities of each city. The common features and dissimilarities in the origin and nature of street dust were investigated through a series of studies in two widely different cities, Madrid (Spain) and Oslo (Norway), between 1990 and 1994. The most comprehensive sampling campaign was carried out in the Norwegian capital during the summer of 1994. An area of 14 km2, covering most of downtown Oslo and some residential districts to the north of the city, was divided into 1 km2 mapping units, and 16 sampling increments of approximately 150 g were collected from streets and roads in each of them. The fraction below 100 μm was acid-digested and analysed by ICP-MS. Statistical analyses of the results suggest that chemical elements in street dust can be classified into three groups: “urban” elements (Ba, Cd, Co, Cu, Mg, Pb, Sb, Ti, Zn), “natural” elements (Al, Ga, La, Mn, Na, Sr, Th, Y) and elements of a mixed origin or which have undergone geochemical changes from their original sources (Ca, Cs, Fe, Mo, Ni, Rb, Sr, U). Soil resuspension and/or mobilisation appears to be the most important source of “natural” elements, while “urban” elements originate primarily from traffic and from the weathering and corrosion of building materials. The data for Pb seem to prove that the gradual shift from leaded to unleaded petrol as fuel for automobiles has resulted in an almost proportional reduction in the concentration of Pb in dust particles under 100 μm. This fact and the spatial distribution of Pb in the city strongly suggest that lead sources other than traffic (i.e. lead accumulated in urban soil over the years) may contribute as much lead, if not more, to urban street dust.

Ionization levels of doped copper indium sulfide chalcopyrites

The electronic structure of modified chalcopyrite CuInS2 has been analyzed from first principles within the density functional theory. The host chalcopyrite has been modified by introducing atomic impurities M at substitutional sites in the lattice host with M = C, Si, Ge, Sn, Ti, V, Cr, Fe, Co, Ni, Rh, and Ir. Both substitutions M for In and M for Cu have been analyzed. The gap and ionization energies are obtained as a function of the M-S displacements. It is interesting for both spintronic and optoelectronic applications because it can provide significant information with respect to the pressure effect and the nonradiative recombination.

Propuesta de una metodología para provisión de servicios de outsourcing de TI

El mercado de outsourcing ha estado creciendo en los últimos años y se prevé que lo siga haciendo en los próximos, pero este crecimiento ha estado limitado por el fracaso de muchos proyectos que, en algunos casos, han llevado a las organizaciones a asumir de nuevo esos servicios (insourcing). Estos fracasos se han debido en gran parte a los problemas con los proveedores: falta de experiencia, de capacidades para asumir los proyectos, dificultad en la comunicación,… A diferencia de lo que ocurre en otras disciplinas, no existe una metodología que ayude, tanto a los clientes como a los proveedores de servicios de outsourcing de TI, a gobernar y gestionar sus proyectos y conseguir los resultados buscados. En los últimos años han aparecido, al mismo tiempo que la expansión del outsourcing, algunos modelos y marcos de buenas prácticas para la gestión de los proyectos de outsourcing, pero generalmente sólo cubren algunos aspectos de la gestión. No se los puede considerar metodologías, porque no definen roles, responsabilidades ni entregables. Por lo general, son el resultado de la experiencia en la gestión de otros tipos de proyectos. Hay que considerar también que, excepto eSCM-SP, que es un modelo de buenas prácticas para mejorar la capacidad en la provisión de servicios, están todos orientados al cliente. El objetivo de esta tesis es, por un lado, demostrar la necesidad de contar con una metodología que guíe a los proveedores durante todo el ciclo de vida un proyecto de outsourcing y, por otro, proponer una metodología que contemple desde la fase inicial de la búsqueda de oportunidades de negocio, evaluación de las propuestas RFP, la decisión de hacer una oferta o no para la prestación de servicios, la participación en la due diligence, la firma del contrato, la transición y la entrega de servicios, hasta la finalización del contrato. La metodología se ha organizado en base a un ciclo de vida del outsourcing de cinco etapas, definiendo para cada una de ellas los roles que participan y las responsabilidades que deberán asumir, las actividades a realizar y los entregables que se deberán generar, y que servirán de elementos de control tanto para la gestión del proyecto como para la provisión del servicio. La validación de la metodología se ha realizado aplicándola en proyectos de provisión de servicios de TI de una mediana empresa española y comparando los resultados obtenidos con los conseguidos en proyectos anteriores. ABSTRACT The outsourcing market has been growing in recent years and it is expected to keep doing so in the coming years, but this growth has been limited by the failure of many projects that, in some cases, has led organizations to take back those services (insourcing). These failures have been due to a major degree to problems with providers: lack of experience and capacity to take on the projects, and difficulties of communication. Unlike what happens in other disciplines, there is no methodology for helping both customers and providers of outsourcing services. In recent years, some good practice frameworks have also appeared at the same time as the expansion of outsourcing. They are not methodologies because they have not defined any roles, responsibilities and deliverables. These frameworks aim to help organizations to be successful at managing and governing outsourcing projects. They are usually the result of their experience in managing other kinds of projects. In consequence, it is not appropriate to name them "methodologies" for managing outsourcing projects and much less "standards". It is also important to note that all existing good practice frameworks, except eSCM-SP, are client-oriented. The aim of this thesis is to state the need to propose a methodology that guides providers throughout the whole outsourcing life cycle and facilitates the provision of quality services and their management, and the proposal of a methodology in which the stages, activities, deliverables, roles and responsibilities are clearly defined. The proposed methodology cover all the stages of the outsourcing life cycle, from the early stage of searching for business opportunities, evaluation of the RFP proposals, the decision to bid or not to bid for the service provision, participation in the due diligence if necessary, the signing of the contract, the transition and delivery of service to the termination of the contract. For each activity, roles, responsibilities and deliverables have been defined. The validation of the methodology has been done by applying it in the provision of some outsourcing projects carried out by a Spanish IT medium company and comparing the results with those obtained in previous projects.

Ti/Pd/Ag Contacts to n-Type GaAs for High Current Density Devices

The metallization stack Ti/Pd/Ag on n-type Si has been readily used in solar cells due to its low metal/semiconductor specific contact resistance, very high sheet conductance, bondability, long-term durability, and cost-effectiveness. In this study, the use of Ti/Pd/Ag metallization on n-type GaAs is examined, targeting electronic devices that need to handle high current densities and with grid-like contacts with limited surface coverage (i.e., solar cells, lasers, or light emitting diodes). Ti/Pd/Ag (50 nm/50 nm/1000 nm) metal layers were deposited on n-type GaAs by electron beam evaporation and the contact quality was assessed for different doping levels (from 1.3 × 1018 cm−3 to 1.6 × 1019 cm−3) and annealing temperatures (from 300°C to 750°C). The metal/semiconductor specific contact resistance, metal resistivity, and the morphology of the contacts were studied. The results show that samples doped in the range of 1018 cm−3 had Schottky-like I–V characteristics and only samples doped 1.6 × 1019 cm−3 exhibited ohmic behavior even before annealing. For the ohmic contacts, increasing annealing temperature causes a decrease in the specific contact resistance (ρ c,Ti/Pd/Ag ~ 5 × 10−4 Ω cm2). In regard to the metal resistivity, Ti/Pd/Ag metallization presents a very good metal conductivity for samples treated below 500°C (ρ M,Ti/Pd/Ag ~ 2.3 × 10−6 Ω cm); however, for samples treated at 750°C, metal resistivity is strongly degraded due to morphological degradation and contamination in the silver overlayer. As compared to the classic AuGe/Ni/Au metal system, the Ti/Pd/Ag system shows higher metal/semiconductor specific contact resistance and one order of magnitude lower metal resistivity.