Unsupervised system to classify SO2 pollutant concentrations in Salamanca, Mexico

Salamanca is cataloged as one of the most polluted cities in Mexico. In order to observe the behavior and clarify the influence of wind parameters on the Sulphur Dioxide (SO2) concentrations a Self-Organizing Maps (SOM) Neural Network have been implemented at three monitoring locations for the period from January 1 to December 31, 2006. The maximum and minimum daily values of SO2 concentrations measured during the year of 2006 were correlated with the wind parameters of the same period. The main advantages of the SOM Neural Network is that it allows to integrate data from different sensors and provide readily interpretation results. Especially, it is powerful mapping and classification tool, which others information in an easier way and facilitates the task of establishing an order of priority between the distinguished groups of concentrations depending on their need for further research or remediation actions in subsequent management steps. For each monitoring location, SOM classifications were evaluated with respect to pollution levels established by Health Authorities. The classification system can help to establish a better air quality monitoring methodology that is essential for assessing the effectiveness of imposed pollution controls, strategies, and facilitate the pollutants reduction.

Air pollution data classification by SOM Neural Network

Over the last ten years, Salamanca has been considered among the most polluted cities in México. This paper presents a Self-Organizing Maps (SOM) Neural Network application to classify pollution data and automatize the air pollution level determination for Sulphur Dioxide (SO2) in Salamanca. Meteorological parameters are well known to be important factors contributing to air quality estimation and prediction. In order to observe the behavior and clarify the influence of wind parameters on the SO2 concentrations a SOM Neural Network have been implemented along a year. The main advantages of the SOM is that it allows to integrate data from different sensors and provide readily interpretation results. Especially, it is powerful mapping and classification tool, which others information in an easier way and facilitates the task of establishing an order of priority between the distinguished groups of concentrations depending on their need for further research or remediation actions in subsequent management steps. The results show a significative correlation between pollutant concentrations and some environmental variables.

The potential of organic fertilizers and water management to reduce N2O emissions in Mediterranean climate cropping systems. A review.

Environmental problems related to the use of synthetic fertilizers and to organic waste management have led to increased interest in the use of organic materials as an alternative source of nutrients for crops, but this is also associated with N2O emissions. There has been an increasing amount of research into the effects of using different types of fertilization on N2O emissions under Mediterranean climatic conditions, but the findings have sometimes been rather contradictory. Available information also suggests that water management could exert a high influence on N2O emissions. In this context, we have reviewed the current scientific knowledge, including an analysis of the effect of fertilizer type and water management on direct N2O emissions. A meta-analysis of compliant reviewed experiments revealed significantly lower N2O emissions for organic as opposed to synthetic fertilizers (23% reduction). When organic materials were segregated in solid and liquid, only solid organic fertilizer emissions were significantly lower than those of synthetic fertilizers (28% reduction in cumulative emissions). The EF is similar to the IPCC factor in conventionally irrigated systems (0.98% N2O-N N applied−1), but one order of magnitude lower in rainfed systems (0.08%). Drip irrigation produces intermediate emission levels (0.66%). Differences are driven by Mediterranean agro-climatic characteristics, which include low soil organic matter (SOM) content and a distinctive rainfall and temperature pattern. Interactions between environmental and management factors and the microbial processes involved in N2O emissions are discussed in detail. Indirect emissions have not been fully accounted for, but when organic fertilizers are applied at similar N rates to synthetic fertilizers, they generally make smaller contributions to the leached NO3− pool. The most promising practices for reducing N2O through organic fertilization include: (i) minimizing water applications; (ii) minimizing bare soil; (iii) improving waste management; and (iv) tightening N cycling through N immobilization. The mitigation potential may be limited by: (i) residual effect; (ii) the long-term effects of fertilizers on SOM; (iii) lower yield-scaled performance; and (iv) total N availability from organic sources. Knowledge gaps identified in the review included: (i) insufficient sampling periods; (ii) high background emissions; (iii) the need to provide N2O EF and yield-scaled EF; (iv) the need for more research on specific cropping systems; and (v) the need for full GHG balances. In conclusion, the available information suggests a potential of organic fertilizers and water-saving practices to mitigate N2O emissions under Mediterranean climatic conditions, although further research is needed before it can be regarded as fully proven, understood and developed.

A survey on service quality description

Quality of service (QoS) can be a critical element for achieving the business goals of a service provider, for the acceptance of a service by the user, or for guaranteeing service characteristics in a composition of services, where a service is defined as either a software or a software-support (i.e., infrastructural) service which is available on any type of network or electronic channel. The goal of this article is to compare the approaches to QoS description in the literature, where several models and metamodels are included. consider a large spectrum of models and metamodels to describe service quality, ranging from ontological approaches to define quality measures, metrics, and dimensions, to metamodels enabling the specification of quality-based service requirements and capabilities as well as of SLAs (Service-Level Agreements) and SLA templates for service provisioning. Our survey is performed by inspecting the characteristics of the available approaches to reveal which are the consolidated ones and which are the ones specific to given aspects and to analyze where the need for further research and investigation lies. The approaches here illustrated have been selected based on a systematic review of conference proceedings and journals spanning various research areas in computer science and engineering, including: distributed, information, and telecommunication systems, networks and security, and service-oriented and grid computing.

Estudio y análisis de la retracción de hormigones normales mediante una base de datos de ensayos unificada

El presente trabajo de investigación se plantea el estudio del fenómeno de la retracción. El fenómeno de la retracción, al igual que otras propiedades del hormigón, ha sido ampliamente divulgado, pero de un tiempo a esta parte, debido a la aparición de nuevos tipos de hormigones (autocompactantes, de altas resistencias, reciclados, etc.) se ha dejado en un segundo plano. Este segundo plano no significa que haya pasado al olvido, pues en los “nuevos hormigones” se toman los modelos de estimación de los hormigones normales como base para estimar sus propiedades, siendo, por este motivo, muy necesario reflexionar sobre si los modelos que estamos empleando son apropiados o no lo son. Este trabajo pretende, mediante la confección de una base de datos que unifica y amplía la del profesor Bazant, realizar un análisis estadístico de los datos que actualmente tenemos a nuestra disposición, y que conforman un total de 802 ensayos que abarcan desde el fenómeno el entumecimiento hasta la retracción total, pasando por la retracción autógena, con un intervalo de tiempo que abarca desde 1958 hasta 2013. Además, este trabajo realiza una revisión de los siete modelos de cálculo más empleados a la hora de estimar la deformación por retracción, analizándolos minuciosamente y superponiéndolos con los datos reales de la base anteriormente nombrada. Como conclusión, se demuestra que los modelos estudiados estiman razonablemente bien el fenómeno de la retracción, si bien no se llegan a discriminar todas las variables con la precisión esperada, siendo alguno de ellos conservador. En este sentido, se abre la puerta a insistir en un estudio más afinado de la retracción del hormigón, por dos motivos: los actuales modelos sirven de base para la estimación de los anteriormente mencionados nuevos hormigones y porque la introducción y desarrollo de aditivos que sean capaces de disminuir este fenómeno deben asentarse ambos sobre una base más sólida y precisa. Por último, deja la puerta abierta para que otros trabajos de investigación puedan realizarse, bien con la retracción, bien con otras propiedades, como el módulo de deformación, la adquisición de resistencias, etc., pues se adjunta como anexo toda la base completa con más de 20.000 datos que pueden ser de gran utilidad. The main objective of this research study is to evaluate the phenomenon of shrinkage in concrete. The phenomenon of shrinkage, as well as other properties of concrete, has been widely studied, but for a time, and due to the emergence of new types of concrete (self-compacting, high strength, recycled, etc.) it has been left in the background. Having moved to second plane did not mean that it have been abandoned, since in the "new concrete" these properties are calculated using the estimation models developed for conventional concrete, and it is for this reason, why it is important and necessary to reflect whether these models we are using are appropriate or are not. This work seeks to unify and bring up-to-date a database of experimental shrinkage results. The database is based on existing databases, especially on the last version of the database created by Professor Bazant. The database includes a total of 802 experimental results, and include results for total shrinkage, autogenous shrinkage and swelling, and over experimental studies for 1958 to 2013. The database serves as a basis for a complex and detailed statistical analysis of the data. In addition, seven commonly used shrinkage estimation models are presented and evaluated. These models are used for a thoroughly comparison analysis between the estimated results obtained using these models and the actual experimental data included in the unified database. In conclusion, it is shown that the models estimate reasonably well the shrinkage strains, although they fail to discriminate adequately some of the influencing variables, resulting in some of them being too conservative in their estimation. In this sense, the results of this work emphasis the importance and the need of addition research on the shrinkage of concrete. This is especially important considering that the existing models provide a basis for estimating the shrinkage in "new concretes", and that the increase use of shrinkage reducing additives should be based and supported by solid research in this field. Finally, this study includes an extensive and updated database that can serve for further research on shrinkage. The full database, developed as part of this work, which includes more than 20,000 data, is included in the annex of the study.

Research on intermediate band solar cells and development of experimental techniques for their characterization under concentrated illumination

Abstract This work is a contribution to the research and development of the intermediate band solar cell (IBSC), a high efficiency photovoltaic concept that features the advantages of both low and high bandgap solar cells. The resemblance with a low bandgap solar cell comes from the fact that the IBSC hosts an electronic energy band -the intermediate band (IB)- within the semiconductor bandgap. This IB allows the collection of sub-bandgap energy photons by means of two-step photon absorption processes, from the valence band (VB) to the IB and from there to the conduction band (CB). The exploitation of these low energy photons implies a more efficient use of the solar spectrum. The resemblance of the IBSC with a high bandgap solar cell is related to the preservation of the voltage: the open-circuit voltage (VOC) of an IBSC is not limited by any of the sub-bandgaps (involving the IB), but only by the fundamental bandgap (defined from the VB to the CB). Nevertheless, the presence of the IB allows new paths for electronic recombination and the performance of the IBSC is degraded at 1 sun operation conditions. A theoretical argument is presented regarding the need for the use of concentrated illumination in order to circumvent the degradation of the voltage derived from the increase in the recombi¬nation. This theory is supported by the experimental verification carried out with our novel characterization technique consisting of the acquisition of photogenerated current (IL)-VOC pairs under low temperature and concentrated light. Besides, at this stage of the IBSC research, several new IB materials are being engineered and our novel character¬ization tool can be very useful to provide feedback on their capability to perform as real IBSCs, verifying or disregarding the fulfillment of the “voltage preservation” principle. An analytical model has also been developed to assess the potential of quantum-dot (QD)-IBSCs. It is based on the calculation of band alignment of III-V alloyed heterojunc-tions, the estimation of the confined energy levels in a QD and the calculation of the de¬tailed balance efficiency. Several potentially useful QD materials have been identified, such as InAs/AlxGa1-xAs, InAs/GaxIn1-xP, InAs1-yNy/AlAsxSb1-x or InAs1-zNz/Alx[GayIn1-y]1-xP. Finally, a model for the analysis of the series resistance of a concentrator solar cell has also been developed to design and fabricate IBSCs adapted to 1,000 suns. Resumen Este trabajo contribuye a la investigación y al desarrollo de la célula solar de banda intermedia (IBSC), un concepto fotovoltaico de alta eficiencia que auna las ventajas de una célula solar de bajo y de alto gap. La IBSC se parece a una célula solar de bajo gap (o banda prohibida) en que la IBSC alberga una banda de energía -la banda intermedia (IB)-en el seno de la banda prohibida. Esta IB permite colectar fotones de energía inferior a la banda prohibida por medio de procesos de absorción de fotones en dos pasos, de la banda de valencia (VB) a la IB y de allí a la banda de conducción (CB). El aprovechamiento de estos fotones de baja energía conlleva un empleo más eficiente del espectro solar. La semejanza antre la IBSC y una célula solar de alto gap está relacionada con la preservación del voltaje: la tensión de circuito abierto (Vbc) de una IBSC no está limitada por ninguna de las fracciones en las que la IB divide a la banda prohibida, sino que está únicamente limitada por el ancho de banda fundamental del semiconductor (definido entre VB y CB). No obstante, la presencia de la IB posibilita nuevos caminos de recombinación electrónica, lo cual degrada el rendimiento de la IBSC a 1 sol. Este trabajo argumenta de forma teórica la necesidad de emplear luz concentrada para evitar compensar el aumento de la recom¬binación de la IBSC y evitar la degradación del voltage. Lo anterior se ha verificado experimentalmente por medio de nuestra novedosa técnica de caracterización consistente en la adquisicin de pares de corriente fotogenerada (IL)-VOG en concentración y a baja temperatura. En esta etapa de la investigación, se están desarrollando nuevos materiales de IB y nuestra herramienta de caracterizacin está siendo empleada para realimentar el proceso de fabricación, comprobando si los materiales tienen capacidad para operar como verdaderas IBSCs por medio de la verificación del principio de preservación del voltaje. También se ha desarrollado un modelo analítico para evaluar el potencial de IBSCs de puntos cuánticos. Dicho modelo está basado en el cálculo del alineamiento de bandas de energía en heterouniones de aleaciones de materiales III-V, en la estimación de la energía de los niveles confinados en un QD y en el cálculo de la eficiencia de balance detallado. Este modelo ha permitido identificar varios materiales de QDs potencialmente útiles como InAs/AlxGai_xAs, InAs/GaxIni_xP, InAsi_yNy/AlAsxSbi_x ó InAsi_zNz/Alx[GayIni_y]i_xP. Finalmente, también se ha desarrollado un modelado teórico para el análisis de la resistencia serie de una célula solar de concentración. Gracias a dicho modelo se han diseñado y fabricado IBSCs adaptadas a 1.000 soles.

Integration of research advances in modelling and monitoring in support of WFD river basin management planning in the context of climate change

The integration of scientific knowledge about possible climate change impacts on water resources has a direct implication on the way water policies are being implemented and evolving. This is particularly true regarding various technical steps embedded into the EU Water Framework Directive river basin management planning, such as risk characterisation, monitoring, design and implementation of action programmes and evaluation of the "good status" objective achievements (in 2015). The need to incorporate climate change considerations into the implementation of EU water policy is currently discussed with a wide range of experts and stakeholders at EU level. Research trends are also on-going, striving to support policy developments and examining how scientific findings and recommendations could be best taken on board by policy-makers and water managers within the forthcoming years. This paper provides a snapshot of policy discussions about climate change in the context of the WFD river basin management planning and specific advancements of related EU-funded research projects. Perspectives for strengthening links among the scientific and policy-making communities in this area are also highlighted.

Research Objects

In the domain of eScience, investigations are increasingly collaborative. Most scientific and engineering domains benefit from building on top of the outputs of other research: By sharing information to reason over and data to incorporate in the modelling task at hand. This raises the need to provide means for preserving and sharing entire eScience workflows and processes for later reuse. It is required to define which information is to be collected, create means to preserve it and approaches to enable and validate the re-execution of a preserved process. This includes and goes beyond preserving the data used in the experiments, as the process underlying its creation and use is essential. This tutorial thus provides an introduction to the problem domain and discusses solutions for the curation of eScience processes.

Six not so easy pieces in intermediate band solar cell research

The concept of "intermediate band solar cell" (IBSC) is, apparently, simple to grasp. However, since the idea was proposed, our understanding has improved and we feel now that we can explain better some concepts than we initially introduced. Clarifying these concepts is important, even if they are well-known for the advanced researcher, so that efforts can be driven in the right direction from start. The six pieces of this work are: Does a miniband need to be formed when the IBSC is implemented with quantum dots?; What are the problems of each of the main practical approaches that exist today? What are the simplest experimental techniques to demonstrate whether an IBSC is working as such or not? What is the issue with the absorption coefficient overlap? and Mott's transition? What the best system would be, if any?

Global research alliance modelling platform (GRAMP): an open web platform for modelling greenhouse gas emissions from agro-ecosystems

Carbon (C) and nitrogen (N) process-based models are important tools for estimating and reporting greenhouse gas emissions and changes in soil C stocks. There is a need for continuous evaluation, development and adaptation of these models to improve scientific understanding, national inventories and assessment of mitigation options across the world. To date, much of the information needed to describe different processes like transpiration, photosynthesis, plant growth and maintenance, above and below ground carbon dynamics, decomposition and nitrogen mineralization. In ecosystem models remains inaccessible to the wider community, being stored within model computer source code, or held internally by modelling teams. Here we describe the Global Research Alliance Modelling Platform (GRAMP), a web-based modelling platform to link researchers with appropriate datasets, models and training material. It will provide access to model source code and an interactive platform for researchers to form a consensus on existing methods, and to synthesize new ideas, which will help to advance progress in this area. The platform will eventually support a variety of models, but to trial the platform and test the architecture and functionality, it was piloted with variants of the DNDC model. The intention is to form a worldwide collaborative network (a virtual laboratory) via an interactive website with access to models and best practice guidelines; appropriate datasets for testing, calibrating and evaluating models; on-line tutorials and links to modelling and data provider research groups, and their associated publications. A graphical user interface has been designed to view the model development tree and access all of the above functions.

Patents and Economic Activity: The Need to Develop Prediction Methods for Patent Applications

Since the decade of the 1980’s the literature on economic development began paying attention to the cases of countries which were industrialized after the first industrial revolution. One of the most relevant aspects analyzed has been the role of technology as a factor which promotes or delays the process of catching up with technology leaders. As result of this interest, new and more adequate indicators were identified to provide a coherent explanation for technological activities and their relationship with economic efficiency. Although the earliest studies focused on analyzing the activities of research and development (R&D), recently the focus of analysis has shifted to another type of variables, more oriented towards the processes of innovation and the gathering of knowledge and capabilities, in which patents provide relevant information.

Is building renovation truly sustainable? The need for applying a multi-criteria assessment through life cycle approach

The aim of the present research is to characterise the international scene in the field of building refurbishment, by thoroughly reviewing the literature relating to building renovation and systematising the results according to the different aspects considered by the authors. Even though there is certain consensus with respect to the criteria for the selection of energy efficiency measures, the assessment criteria differ broadly and widely. The present work highlights the lack of consensus on the assessment criteria and the need of harmonization. A holistic view is required in order to identify the most sustainable strategies in each particular case, considering social, environmental and economic impacts from a life cycle perspective.

The development of architecture and urban design in China and the problem we need to solve = La utilización de la baja tecnología en la arquitectura popular de China y su combinación con el método del diseño arquitectónico moderno

In this article, I will research this topic from these aspects: the material, architectural forms, building technology and space experience, hoping to figure out the characteristic of traditional Chinese architecture and the use of low technology in it, explore a suitable path of the development of Chinese Vernacular Architecture.