Radiofrequency architectures and technologies for software defined radio

Six-port network is an interesting radiofrequency architecture with multiple possibilities. Since it was firstly introduced in the seventies as an alternative network analyzer, the six-port network has been used for many applications, such as homodyne receivers, radar systems, direction of arrival estimation, UWB (Ultra-Wide-Band), or MIMO (Multiple Input Multiple Output) systems. Currently, it is considered as a one of the best candidates to implement a Software Defined Radio (SDR). This thesis comprises an exhaustive study of this promising architecture, where its fundamentals and the state-of-the-art are also included. In addition, the design and development of a SDR 0.3-6 GHz six-port receiver prototype is presented in this thesis, which is implemented in conventional technology. The system is experimentally characterized and validated for RF signal demodulation with good performance. The analysis of the six-port architecture is complemented by a theoretical and experimental comparison with other radiofrequency architectures suitable for SDR. Some novel contributions are introduced in the present thesis. Such novelties are in the direction of the highly topical issues on six-port technique: development and optimization of real-time I-Q regeneration techniques for multiport networks; and search of new techniques and technologies to contribute to the miniaturization of the six-port architecture. In particular, the novel contributions of this thesis can be summarized as: - Introduction of a new real-time auto-calibration method for multiport receivers, particularly suitable for broadband designs and high data rate applications. - Introduction of a new direct baseband I-Q regeneration technique for five-port receivers. - Contribution to the miniaturization of six-port receivers by the use of the multilayer LTCC (Low Temperature Cofired Ceramic) technology. Implementation of a compact (30x30x1.25 mm) broadband (0.3-6 GHz) six-port receiver in LTTC technology. The results and conclusions derived from this thesis have been satisfactory, and quite fruitful in terms of publications. A total of fourteen works have been published, considering international journals and conferences, and national conferences. Aditionally, a paper has been submitted to an internationally recognized journal, which is currently under review.

Tutoriales multimedia para sistemas de telecomunicación

Este Proyecto Fin de Carrera está destinado a la ilustración y aprendizaje del uso de varios dispositivos de los laboratorios del Departamento de Ingeniería Audiovisual y Comunicaciones, de la Escuela Universitaria de Ingeniería Técnica de Telecomunicación, de la Universidad Politécnica de Madrid, en forma de vídeos tutoriales basados en mediciones y prácticas habituales de las asignaturas del departamento para que puedan ser utilizados por los alumnos de la escuela como apoyo a las explicaciones del profesor en ocasiones puntuales. En concreto se han realizado hasta seis vídeos tutoriales en los que se explica: el diseño de un circuito impreso y la creación y fabricación de éste. Por otro lado, también se ha explicado el fenómeno del ruido de fase y cómo es el proceso de su medida, como una de las muchas características de un analizador de espectros. A modo de análisis, se ha realizado otro tutorial acerca de la modulación en FM, sus características y sus aplicaciones. Por último se ha hecho un estudio del comportamiento de un analizador de redes, exponiendo su funcionamiento y explicando su proceso de calibración. Para la realización de estos tutoriales se han utilizado diferentes aplicaciones sobre creación de vídeos multimedia, animación, producción de audio y narración. En especial se han usado: Sprint-Layout 5.0, Adobe Flash Professional CS5.5, Camtasia studio 7, Corel VideoStudio Pro X4, Loquendo TTS7 y WinPlot. Para el apartado de las grabaciones de las diferentes escenas se ha necesitado el uso de distintos instrumentos de medida del laboratorio tales como: analizador de espectros, analizador de redes, generador de señal, generador de funciones, osciloscopio y otros equipos adicionales como: cámara de vídeo y trípode del departamento. Para la composición de los diferentes tutoriales se ha comenzado creando un guion, para cada uno de ellos, estableciendo la aparición de las imágenes, vídeos, y locución. A continuación se exponen los diferentes temas en los que se han basado estos tutoriales de laboratorio, uno a uno. ABSTRACT. This Project is destined to learn the use of several devices at the laboratory of “Ingeniería Audiovisual y Comunicaciones” Department at “Escuela Universitaria de Ingeniería técnica de Telecomunicaciones” of “Universidad Politécnica de Madrid”, on the way as tutorial videos base on the subjects from this department to be used by the college students as help of the teacher’s explanations. In this project you will find up to six tutorial videos, showing: printed circuit design, printed circuit board manufacture. You can also find an explanation about the phenomenon of phase noise and how it’s its measurement process, as one of the many features of a spectrum analyzer. Another tutorial video is based on FM modulation, its features and applications. The last tutorial explains the networks analyzer functionalities and its calibration process. To carry out these tutorials different applications have been used to create multimedia videos, animation, audio production and storytelling. Such as Sprint Layout 5.0, Camtasia 7.0, Corel VideoStudio Pro X4, Adobe Flash Professional CS5.5, Loquendo TTS7 y WinPlot. About the recording side of the different scenes, several equipment have been required at the laboratory, such as spectrums analyzer, signal generator, oscilloscope, function generator, network analyzer and other additional devices, such as: a video camera with its tripod. The composition of the different tutorials has begun creating a script, for each of them, setting the times of appearance of images, video, speech and music. After this abstract, the different topics of the tutorials are showed, one by one.

Diseño, implementación y verificación de una antena de microondas

A lo largo de este proyecto se han tratado las diferentes fases que tienen lugar durante el desarrollo del programa de Diseño y Verificación de una Bocina en Banda C destinada a un satélite comercial de comunicaciones. En un primer lugar, se introduce el proyecto en el mundo real realizando una pequeña aproximación a los satélites artificiales y su historia. Después, en una primera fase, se describen los diversos puntos de la etapa de diseño y los resultados de la simulación de nuestra Antena. Se estudian por separado los diferentes elementos que componen el equipo, y además, se realiza un análisis de los parámetros eléctricos que se deben tener en cuenta durante el diseño para adaptar el comportamiento de la Antena a los requisitos solicitados por el cliente. Antes de realizar la verificación de la Antena, se procede a la definición de los ensayos, que se debe realizar sobre el equipo con el fin de simular las condiciones a las que se verá sometido. Pruebas y medidas, niveles de test, etc. que nos ayudan a demostrar que nuestra Antena está preparada para realizar su misión en el espacio. Se hará una descripción sobre la forma de realizar de los ensayos y de las instalaciones donde se van a llevar a cabo, además del orden que llevaremos durante la campaña. Una vez determinados los test y con la Antena fabricada y lista, se procede a la Verificación de nuestro equipo mediante la Campaña de Ensayos con el objetivo de caracterizar por completo el funcionamiento de nuestra Antena en cualquier circunstancia. Se muestran los resultados obtenidos en los test siguiendo el orden establecido por el Test Plan. Medidas en Laboratorio y Radiación, los test de vibración y las pruebas ambientales en las Cámaras Térmicas de Vacío, y medidas eléctricas en condiciones extremas de temperatura y presión. Y una vez realizada la Campaña, se vuelve a medir la Antena para comprobar el funcionamiento tras soportar todos los ensayos. Se analizan los resultados obtenidos en cada una de las pruebas y se comparan con las simulaciones obtenidas durante la fase de diseño. Finalmente, se realiza un pequeño resumen de los valores más importantes obtenidos durante la Verificación y exponen las Conclusiones que se desprende de dicho proceso. Como último punto del proyecto, se estudian las correcciones y mejoras que se podrán llevar a cabo en futuros programas gracias a lo que hemos aprendido en este proyecto. Abstract This project presents a C Band Horn Antenna for a commercial communications satellite. All the different phases from Design to Verification are presented. First of all, an introduction to artificial satellites and their history is presented to put this project into perspective. Next, the electrical design of the Antenna is presented. Taking into account the theoretical fundamentals, each element that comprises this Antenna was designed. Their electrical performances, obtained from analysis using commercial software, are presented in the simulation results. In the design of each element of the antenna, some critical parameters are set and optimized in order to be compliant with the global requirements requested by the customer. After the design is completed, it is necessary to define the Test Campaign that has to be carried out in order to verify the validity of the designed and manufactured Antenna. Therefore, a Test Plan and the Electrical and Environmental Test Procedures are defined. This Test Campaign must be representative of the same conditions of the real space mission. Considering this, the following are defined: parameters for the network analyzer and radiation patterns measurements; test levels for the environmental test; definition of the RF measurements to be carried out and the temperatures to be applied in the thermal vacuum cycling. If the Antenna surpasses these tests, it will be ready to perform its mission in space over the entire satellite’s life cycle. The facilities where the tests are performed, as well as the sequence of the tests along the campaign are described too. After that, the Test Campaign is performed to fully characterize the Antenna in the space simulated conditions. Following the order established in the Test Plan, a radiation pattern and laboratory parameters are measured to correlate its electrical response with the simulations. Then, vibration and thermal vacuum tests are performed to verify its behavior in extreme environmental conditions. Last, if the final electrical results are the same as the initial ones, it can be stated that the antenna has successfully passed the Test Campaign. And finally, conclusions obtained from the data simulation design and Test Campaign results are presented. Status of Compliance with the specification is shown to demonstrate that the Antenna fulfills the requested requirements. Although the purpose of this project is to design and verify the response of C Band Horn Antenna, it is important to highlight improvements for future developments and the lessons learnt during this project.

Compact duplexing for a 680-GHz radar using a waveguide orthomode transducer

A compact 680-GHz waveguide orthomode transducer (OMT) and circular horn combination has been designed, tested, and characterized in a radar transceiver's duplexer. The duplexing capability is implemented by a hybrid waveguide quasi optical solution, combining a linear polarization OMT and an external grating polarizer. Isolation between the OMT's orthogonal ports' flanges was measured with a vector network analyzer to exceed 33 dB over a >10% bandwidth between 630 and 710 GHz. Calibrated Y-factor measurements using a mixer attached to the OMT ports reveal losses through the transmit and receive paths that sum to an average of 4.7 dB of two-way loss over 660-690 GHz. This is consistent with radar sensitivity measurements comparing the new OMT/horn with a quasi-optical wire grid beam splitter. Moreover, the radar performance assessment validates the OMT as a suitable compact substitute of the wire grid for the JPL's short-range 680-GHz imaging radar.

A Light-Weight On-Chip Monitoring Network for Dynamic Adaptation and Calibration

Current nanometer technologies suffer within-die parameter uncertainties, varying workload conditions, aging, and temperature effects that cause a serious reduction on yield and performance. In this scenario, monitoring, calibration, and dynamic adaptation become essential, demanding systems with a collection of multi purpose monitors and exposing the need for light-weight monitoring networks. This paper presents a new monitoring network paradigm able to perform an early prioritization of the information. This is achieved by the introduction of a new hierarchy level, the threshing level. Targeting it, we propose a time-domain signaling scheme over a single-wire that minimizes the network switching activity as well as the routing requirements. To validate our approach, we make a thorough analysis of the architectural trade-offs and expose two complete monitoring systems that suppose an area improvement of 40% and a power reduction of three orders of magnitude compared to previous works.

Using the Spectrum Analyzer as an Educational Tool for Mobile Communications

Application of the spectrum analyzer for illustrating several concepts associated with mobile communications is discussed. Specifically, two groups of observable features are described. First, time variation and frequency selectivity of multipath propagation can be revealed by carrying out simple measurements on commercial-network GSM and UMTS signals. Second, the main time-domain and frequency-domain features of GSM and UMTS radio signals can be observed. This constitutes a valuable tool for teaching mobile communication courses.

On-chip Monitoring: A Light-Weight Interconnection Network Approach

Current nanometer technologies are subjected to several adverse effects that seriously impact the yield and performance of integrated circuits. Such is the case of within-die parameters uncertainties, varying workload conditions, aging, temperature, etc. Monitoring, calibration and dynamic adaptation have appeared as promising solutions to these issues and many kinds of monitors have been presented recently. In this scenario, where systems with hundreds of monitors of different types have been proposed, the need for light-weight monitoring networks has become essential. In this work we present a light-weight network architecture based on digitization resource sharing of nodes that require a time-to-digital conversion. Our proposal employs a single wire interface, shared among all the nodes in the network, and quantizes the time domain to perform the access multiplexing and transmit the information. It supposes a 16% improvement in area and power consumption compared to traditional approaches.

A simple genetic algorithm for calibration of stochastic rock discontinuity networks

Este artículo propone un método para llevar a cabo la calibración de las familias de discontinuidades en macizos rocosos. We present a novel approach for calibration of stochastic discontinuity network parameters based on genetic algorithms (GAs). To validate the approach, examples of application of the method to cases with known parameters of the original Poisson discontinuity network are presented. Parameters of the model are encoded as chromosomes using a binary representation, and such chromosomes evolve as successive generations of a randomly generated initial population, subjected to GA operations of selection, crossover and mutation. Such back-calculated parameters are employed to make assessments about the inference capabilities of the model using different objective functions with different probabilities of crossover and mutation. Results show that the predictive capabilities of GAs significantly depend on the type of objective function considered; and they also show that the calibration capabilities of the genetic algorithm can be acceptable for practical engineering applications, since in most cases they can be expected to provide parameter estimates with relatively small errors for those parameters of the network (such as intensity and mean size of discontinuities) that have the strongest influence on many engineering applications.

Analysis of calibration results from cup and propeller anemometers. Influence on wind turbine Annual Energy Production (AEP) calculations

The calibration coefficients of several models of cup and propeller anemometers were analysed. The analysis was based on a series of laboratory calibrations between January 2003 and August 2007. Mean and standard deviation values of calibration coefficients from the anemometers studied were included. Two calibration procedures were used and compared. In the first, recommended by the Measuring network of Wind Energy Institutes (MEASNET), 13 measurement points were taken over a wind speed range of 4 to 16  m  s−1. In the second procedure, 9 measurement points were taken over a wider speed range of 4 to 23  m  s−1. Results indicated no significant differences between the two calibration procedures applied to the same anemometer in terms of measured wind speed and wind turbines' Annual Energy Production (AEP). The influence of the cup anemometers' design on the calibration coefficients was also analysed. The results revealed that the slope of the calibration curve, if based on the rotation frequency and not the anemometer's output frequency, seemed to depend on the cup center rotation radius.