Prediction of bendig load capacity of timber beams by finite element method simulation of knots and grain deviation

A finite element model was used to simulate timberbeams with defects and predict their maximum load in bending. Taking into account the elastoplastic constitutive law of timber, the prediction of fracture load gives information about the mechanisms of timber failure, particularly with regard to the influence of knots, and their local graindeviation, on the fracture. A finite element model was constructed using the ANSYS element Plane42 in a plane stress 2D-analysis, which equates thickness to the width of the section to create a mesh which is as uniform as possible. Three sub-models reproduced the bending test according to UNE EN 408: i) timber with holes caused by knots; ii) timber with adherent knots which have structural continuity with the rest of the beam material; iii) timber with knots but with only partial contact between knot and beam which was artificially simulated by means of contact springs between the two materials. The model was validated using ten 45 × 145 × 3000 mm beams of Pinus sylvestris L. which presented knots and graindeviation. The fracture stress data obtained was compared with the results of numerical simulations, resulting in an adjustment error less of than 9.7%

Analysis by finite element calculations of light scattering in laser-textured AZO films for PV thin-film solar cells

In the thin-film photovoltaic industry, to achieve a high light scattering in one or more of the cell interfaces is one of the strategies that allow an enhancement of light absorption inside the cell and, therefore, a better device behavior and efficiency. Although chemical etching is the standard method to texture surfaces for that scattering improvement, laser light has shown as a new way for texturizing different materials, maintaining a good control of the final topography with a unique, clean, and quite precise process. In this work AZO films with different texture parameters are fabricated. The typical parameters used to characterize them, as the root mean square roughness or the haze factor, are discussed and, for deeper understanding of the scattering mechanisms, the light behavior in the films is simulated using a finite element method code. This method gives information about the light intensity in each point of the system, allowing the precise characterization of the scattering behavior near the film surface, and it can be used as well to calculate a simulated haze factor that can be compared with experimental measurements. A discussion of the validation of the numerical code, based in a comprehensive comparison with experimental data is included.

New non-reorientational optical nonlinear effect in MBBA

A new effect producing self-focusing of light in a nematic MBBA film is reported. This effect produces a static diffraction pattern composed of circular rings which is different from the ones arising from self-focusing previously reported. The influence of the cell thickness, the optical intensity, and the wavelength is studied. Once the nematic is distorted by a láser beam, the effect produced in other light beam passing through the modified región is independent of its polarization. This isotropic behavior shows that a molecular reorientation has not been produced. The origin of this effect seems to be the same of that of the effect which produces a randomly oscillating diffraction pattern previously reported by our group. Some possible causes such as thermal indexing, convective instabilities and self-induced transparency are discussed.

Parallel Algorithms for FE-BE Coupling

When non linear physical systems of infinite extent are modelled, such as tunnels and perforations, it is necessary to simulate suitably the solution in the infinite as well as the non linearity. The finite element method (FEM) is a well known procedure for simulating the non linear behavior. However, the treatment of the infinite field with domain truncations is often questionable. On the other hand, the boundary element method (BEM) is suitable to simulate the infinite behavior without truncations. Because of this, by the combination of both methods, suitable use of the advantages of each one may be obtained. Several possibilities of FEM-BEM coupling and their performance in some practical cases are discussed in this paper. Parallelizable coupling algorithms based on domain decomposition are developed and compared with the most traditional coupling methods.

Modelización y simulación numérica de sistemas geotérmicos planos

En el presente proyecto se estudiará la conveniencia de utilizar simulación numérica para evaluar, diseñar y mejorar el diseño de instalaciones geotérmicas planas. Para ello, se modelizará el conjunto de terreno y sistema geotérmico mediante el acoplamiento de un modelo tridimensional (terreno) y un modelo unidimensional, formado por la red de tubería geotérmica, que estará dispuesta en un plano cuya orientación dependerá de las aplicaciones. Para la simulación numérica se utilizará un software de análisis y resolución por elementos finitos tipo comercial. Finalmente, se definirán unos parámetros geométricos de diseño y, teniendo en cuenta las propiedades térmicas de cada material, se realizarán estudios paramétricos para determinar la influencia de cada grupo de parámetros. Ello requerirá la realización de cientos de simulaciones numéricas que permitirán optimizar el rendimiento de sistemas geotérmicos planos tanto horizontales (soleras), como verticales (muros pantalla). ABSTRACT In this project it is going to be studied the convenience of numerical simulation as to evaluate, design and improve the design of geothermal planar installations. With this purpose, the terrain and the geothermal system will be modeled by coupling a three-dimensional model (terrain) and a one-dimensional model formed by the geothermal piping network disposed in a plane with an orientation which will depend on the applications. For the numerical simulation commercial software of analyzing and resolving by finite elements will be used. Finally, geometric design parameters will be defined, and taking into account the thermal properties of each material, parametric studies will be performed to determine the influence of each group of parameters. This will require the completion of hundreds of numerical simulations which will enhance the performance of both horizontal (slabs) and vertical (diaphragm walls) geothermal systems.

Modelización de las propiedades radiativas e interacción de láseres ultraintensos con la materia

Desde el año 2004 el código ARWEN ha sido utilizado con éxito para simular y diseñar experimentos relacionados con blancos para fusión por confinamiento inercial [146], astrofísica de laboratorio [145], plasmas como amplificadores de láseres de rayos X [107] o plasmas creados por láser para la medición de espectros de transmisión. Para la realización de estas simulaciones es necesario, además de métodos de alto orden precisos y que presenten buenas propiedades conservativas, conocer ciertas propiedades de los plasmas. En el caso de la fluidodinámica y la conducción electrónica necesitaremos conocer la ecuación de estado [94, 49, 36], y para el transporte de la radiación será preciso disponer de los datos de absorción y emisión [104, 95, 40]. Hasta el año 2009 ARWEN dependía de códigos externos para la generación de estas tablas de opacidad, careciendo de control sobre los métodos empleados para su generación. Además estos códigos asumían equilibrio local termodinámico (LTE), limitando su validez a rangos de alta densidad y baja temperatura. En el marco de esta tesis se ha desarrollado el código BIGBART para la generación de tablas detalladas de opacidad y emisividad para su uso en el módulo de transporte de radiación. De esta forma el grupo dispondrá de su propia herramienta de generación de propiedades radiativas. El código desarrollado es capaz de tratar plasmas en estado fuera de equilibrio (non-LTE) mediante el modelo colisional-radiativo, extendiendo así el rango de validez de las tablas generadas. El trabajo desarrollado para implementar un código LTE/non-LTE estacionario es el siguiente Cálculo de estructura y datos atómicos. Se ha acoplado en código FAC a BIGBART, incorporando la capacidad para generar potenciales atómicos para una configuración y el cálculo de funciones de onda de electrones en orbitales ligados y libres. Aproximaciones y métodos para la obtención de tasas y secciones eficaces de procesos. Se han incluido y programado los modelos implementados en FAC para el cálculo de secciones eficaces de fotoionización, y tasas de decaimiento de emisión espontánea y autoionización. Además se ha incluido el modelo Plane-Wave Born (PWBA) para el cálculo de las secciones eficaces de ionización y excitación colisional. Modelos para la obtención de la distribución de estados iónicos dentro del plasma. Se ha programado un solver LTE basado en la ecuación de Saha-Boltzmann con efectos de ionización por presión debida a los iones adyacentes. También se ha implementado un modelo non-LTE colisionalradiativo para la resolución del sistema de ecuaciones que nos permite obtener la densidad de estados iónicos fuera de equilibrio. Modelo non-LTE RADIOM. Se ha implementado el modelo RADIOM para aproximar efectos de no-equilibrio mediante cálculos LTE a una temperatura equivalente, menor o igual que la temperatura electrónica real. Cálculo de las propiedades espectrales de absorción y emisión. Se han implementado los modelos para el cálculo de los perfiles espectrales de absorción y emisión para procesos entre niveles ligados, ligado-libre y librelibre. Aprovechando el trabajo realizado en este sentido, durante el transcurso de esta tesis se amplió el código BIGBART para tratar problemas con dependencia temporal. La extensión para tratar este tipo de problemas se orientó a la simulación numérica de la interacción de láseres ultra intensos en el rango XUV/rayos X. Para ello, además de adaptar el modelo non-LTE colisionalradiativo se incluyeron procesos adicionales asociados a la interacción de la materia con fotones altamente energéticos. También se han incluido modelos para el cálculo de las propiedades ópticas, y por ende las propiedades dieléctricas de la materia irradiada, de gran interés en algunas aplicaciones novedosas de estos láseres intensos. Debido a la naturaleza fuertemente fuera de equilibrio en la interacción de fotones de alta energía con la materia, se incluyó el tratamiento de la distribución de electrones libres fuera de equilibrio en la aproximación de Fokker-Planck, tanto para condiciones degeneradas como no degeneradas. El trabajo desarrollado en el código non-LTE con dependencia temporal es el siguiente Procesos asociados a láseres intensos XUV/rayos X. Se ha implementado el cálculo de procesos radiativos estimulados de absorción y emisión por el láser. También se han incluido procesos asociados a la creación de vacantes en capas internas electrónicas (Shake), además de doble autoionización y doble fotoionización. Cálculo de propiedades ópticas y dieléctricas en blancos sólidos. Se ha implementado un modelo para la absorción por bremsstrahlung inverso en blancos en estado sólido. Con el coeficiente de extinción debido a procesos de fotoabsorción resonante, fotoionización y bremsstrahlung inverso se obtiene el ´ındice de refracción mediante la relación de Kronig-Kramers. Electrones fuera de equilibrio. Se ha tratado la evolución de la distribución de electrones, cuando no está justificado asumir que es Maxwelliana o de Fermi-Dirac, mediante la aproximación de Fokker-Planck para la colisión entre electrones libres. En la resolución de la ecuación de Fokker-Planck se han incluido los procesos inelásticos por colisiones con iones y términos fuente por interacción con el láser y otros procesos. ABSTRACT Since 2004 the ARWEN code has been successfully used to simulate and design targets for inertial confinement fusion experiments [146], laboratory astrophysics [145], plasmas as X-ray lasers amplifiers [107] or laser created plasmas for measuring transmission spectra. To perform these simulations it is necessary, in addition to high order precise methods with good conservative properties, to know certain properties of plasmas. For fluid dynamic and electronic conduction we need to know the equation of state [94, 49, 36], and for radiation transport it will be necessary to have the data of the absorption and emission [104, 95, 40]. Until 2009 ARWEN depended on external codes to generate these opacity tables, lacking of control over the methods used for their generation. Besides, these codes assumed local thermodynamic equilibrium (LTE), limiting their validity ranges to high densities and low temperatures. As part of this thesis it has been developed the BIGBART code for generating detailed opacity and emissivity tables for use in the radiation transport module. This group will have its own tool for the generation of radiative properties. The developed code is capable of treating plasmas out of equilibrium (non-LTE) by means of a collisional-radiative model, extending the range of validity of the generated tables. The work to implement an LTE/non-LTE steady-state code is as follows Calculation of structure and atomic data. the FAC code was coupled to BIGBART, incorporating the ability to generate atomic potentials for calculating configuration wave functions for bound and free electrons. Approaches and methods for obtaining cross sections and processes rates. We have included and reprogrammed in Fortran the models implemented in FAC for calculation of photoionization cross sections and decay rates of spontaneous emission and autoionization. We also included the Plane- Wave Born (PWBA) model to calculate the cross sections of ionization and collisional excitation. Models for the obtention of the distribution of ionic states within the plasma. We programmed a LTE solver based on the Saha-Boltzmann equation with pressure ionization effects due to adjacent ions. It has also been implemented a non-LTE collisional-radiative model for solving the system of equations that allows us to obtain the density of ionic states out of equilibrium. Non-LTE RADIOM model. We have implemented the non-LTE RADIOM model to approximate non-equilibrium effects with LTE data at an equivalent temperature, lower or equal to the actual electronic temperature. Calculation of the spectral absorption and emission properties. Models have been implemented for the calculation of the spectral profiles of absorption and emission processes between bound levels, free-bound and free-free. Taking advantage of the work done in this direction throughout the course of this thesis the code BIGBART was extended to treat time-dependent problems. The extension to treat such problems is oriented to the numerical simulation of the interaction of ultra intense lasers in the XUV/X-ray range. For this range, in addition to adapting the non-LTE collisional-radiative model, additional processes associated with the interaction of matter with high energy photons. We also included models for calculation of the optical properties, and therefore the dielectric properties of the irradiated material, of great interest in some novel applications of these intense lasers. Due to the strong non-equilibrium nature of the interaction of high energy photons with matter, we included the treatment of the distribution of free electrons out of equilibrium in the Fokker-Planck approximation for both degenerate and non-degenerate conditions. The work in the non-LTE time-dependent code is as follows Processes associated with intense XUV/X-ray lasers. We have implemented the calculation of stimulated radiative processes in absorption and emission. Also we included processes associated with the creation of electronic vacancies in inner shells (Shake), double autoionization and double photoionization. Calculation of optical and dielectric properties in solid targets. We have implemented a model for inverse bremsstrahlung absorption in solid targets. With the extinction coefficient from resonant photoabsorption, photoionization and inverse bremsstrahlung the refractive index is obtained by the Kramers-Kronig relation. Electrons out of equilibrium. We treat the evolution of the electron distribution, when it is not justified to assume a Maxwellian or Fermi-Dirac distribution, by the Fokker-Planck approximation for collisions between electrons. When solving the Fokker-Planck equation we included inelastic collision processes with ions and source terms by interaction with the laser and other processes.

The development of a wind tunnel DAQ system by using Labview tools

This paper presents the experimental three-year learning activity developed by a group of teachers in a wind tunnel facility. The authors, leading a team of students, carried out a project consisting of the design, assembly and testing of a wind tunnel. The project included all stages of the process from its initial specifications to its final quality flow assessments, going through the calculation of each element, and the building of the whole wind tunnel. The group of (final year) students was responsible for the whole wind tunnel project as a part of their bachelor degree project. The paper focuses on the development of wind tunnel data acquisition software. This automatic tool is essential to improve the automation of the data acquisition of the wind tunnel facility systems, in particular for a 6DOF multi-axis force/torque sensor. This work can be considered as a typical example of real engineering practice: a set of specifications that has to be modified due to the constraints imposed throughout the project, in order to obtain the final result

Automated end user-centred adaptation of web components through automated description logic-based reasoning

Context: This paper addresses one of the major end-user development (EUD) challenges, namely, how to pack today?s EUD support tools with composable elements. This would give end users better access to more components which they can use to build a solution tailored to their own needs. The success of later end-user software engineering (EUSE) activities largely depends on how many components each tool has and how adaptable components are to multiple problem domains. Objective: A system for automatically adapting heterogeneous components to a common development environment would offer a sizeable saving of time and resources within the EUD support tool construction process. This paper presents an automated adaptation system for transforming EUD components to a standard format. Method: This system is based on the use of description logic. Based on a generic UML2 data model, this description logic is able to check whether an end-user component can be transformed to this modeling language through subsumption or as an instance of the UML2 model. Besides it automatically finds a consistent, non-ambiguous and finite set of XSLT mappings to automatically prepare data in order to leverage the component as part of a tool that conforms to the target UML2 component model. Results: The proposed system has been successfully applied to components from four prominent EUD tools. These components were automatically converted to a standard format. In order to validate the proposed system, rich internet applications (RIA) used as an operational support system for operators at a large services company were developed using automatically adapted standard format components. These RIAs would be impossible to develop using each EUD tool separately. Conclusion: The positive results of applying our system for automatically adapting components from current tool catalogues are indicative of the system?s effectiveness. Use of this system could foster the growth of web EUD component catalogues, leveraging a vast ecosystem of user-centred SaaS to further current EUSE trends.