Study of Impact and Compression Damage on Asian Pears

Result of impact and compression tests on Chojuro, Twentieth Century, Tsu Li, and Ya Li varieties of Asian pears indicate that Chojuro pears are the firmest and most resistant to mechanical damage. At the time of harvest, Tsu Li and Ya Li pears could resist mechanical damage nearly as well as Chojuro pears, but they become more susceptible to bruising in cold storage. Twentieth Century pears are most sensitive to impact and compression bruising. Increased time in the ripening room produces more softening and increased bruise resistance of Chojuro and Twentieth Century pears than of Tsu Li and Ya Li pears.

Damage mechanisms in the handling of fruits

The recognition of an increasing and worldwide demand for high quality in fruits and vegetables has grown in recent years. Evidence of severe problems of mechanical damage is increasing, and this is affecting the trade of fruits in European and other countries. The potential market for fresh high-quality vegetables and fruits remains restricted by the lack of quality of the majority of products that reach consumers; this is the case for local as well as import/export markets, so a reduction in the consumption of fresh fruits in favour of other fixed-quality products (dairy in particular) may become widespread. In a recent survey (King, 1988, cited in Bellon, 1989), it appears that, for the moment, one third of the surveyed consumers are still continuing to increase their fresh produce consumption. The factors that appear as being most important in influencing the shopping behaviour of these consumers are taste/flavour, freshness/ripeness, appealing look, and cleanliness. Research on mechanical damage in fruit and vegetables has been underway for several years. The first research made on physical properties of fruits was in fact directed towards analysing the response to slow or rapid loading of selected fruits (Fridley et al, 1968; Horsefield et al., 1972). From that time on, research has expanded greatly, and different aspects of the problem have been approached. These include applicable mechanical models for the contact problem, the response of biological tissues to loading, devices for detecting damage causes in machines and equipment, and procedures for sensing bruises in grading and sorting. This chapter will be devoted to the study of actual research results relative to the cause and mechanisms of mechanical damage in fruits (secondarily in vegetables), the development of bruises in these commodities, the models that have been used up to now, and the different factors which have been recognized as influencing the appearance and development of mechanical damage in fruits. The study will be focused mainly on contact-damage - that is, slow or rapid loads applied to the surface of the products and causing bruises. (A bruise is defined as an altered volume of fruit tissues below the skin that is discoloured and softened.) Other types of mechanical damage, like abrasion and scuffing, punctures and cuts, will be also mentioned briefly.

Effects of precooling and degreening treatments on the susceptibility of peach and citrus to handling damage.

Mechanical damage to fruits results from a combination of fruit properties and of damage inflicting effects by the handling equipment. Treatments were applied to fruits which affect mechanical damage susceptibility: precooling for stone fruits and degreening to citrus fruits. Laboratory tests (compression, impact, tumbling, abrasion) and field tests (damage in the handling lines) were applied to (3) peach, (2) apricot, (2) orange and (1) lemon varieties. Hydroor-air-cooling influence positively peach and apricot firmness and cause a significant reduction in: number of bruised fruits, and size of visible bruise, when combined with a low level of loading during handling. Degreening also affects the resistance of citrus fruits to handling, when compared to green fruits.

Models for the prediction of handling damage in citrus and peaches grading lines, related to their physical properties.

Fruit damage during harvesting and handling is a standing problem, particularly for susceptible fruits like peaches and apricots. The resulting mechanical damage is a combination of fruit properties and damage inflicting effects due to procedures and to the equipment. Nine packing lines in the region of Murcia (SE Spain) have been tested with the aid of two different-size electronic fruits IS-100. Probabilities of impacts above three preset thresholds (50 g's, 100 g's and 150 g's) were calculated for each transfer point. Interaction fruit-packing line tests have been also performed in order to study the real incidence of packing lines on natural produce: apricots (1 variety), peaches (3 v.), lemons (1 v.) and oranges (3 v.). Bruises of handled and not handled samples of fruits were compared.

Nuevos mecanismos moleculares de tolerancia a sequía y otros tipos de estrés abiótico en especies arbóreas de interés económico

Las masas forestales tienen una importancia colosal para nuestra sociedad y el conjunto de la biosfera. Estudios recientes a escala mundial indican que la sequía es el factor abiótico que más afecta a su crecimiento y supervivencia, seguida por las temperaturas extremas y la salinidad. Aunque comprender los mecanismos con que las especies arbóreas toleran estas formas de estrés tiene un interés aplicado evidente, dichos mecanismos se han estudiado mucho más en especies herbáceas modelo o de interés agronómico. Existen sin embargo diferencias notables entre ellas, como se demuestra en esta tesis y en otros trabajos recientes. Nuestro estudio se centra concretamente en la respuesta molecular del chopo –el sistema modelo forestal más desarrollado– al estrés abiótico, con particular énfasis en la sequía. Utilizando una estrategia proteómica y tratamientos controlados, hemos identificado componentes mayoritarios de dicha respuesta. Su participación en la misma se ha validado mediante análisis transcripcionales detallados utilizando tecnología qRT-PCR (PCR cuantitativa en tiempo real). Hemos identificado proteínas cuyo nexo funcional con mecanismos de tolerancia ya era conocido, como chaperonas moleculares sHSP o enzimas que atenúan el estrés oxidativo, pero también proteínas cuya relación funcional con el estrés es menos clara o incluso novedosa, como polifenol oxidasas (PPO), deshidrogenasas/reductasas de cadena corta (SDR), o bicupinas (BIC), entre otras. El cuerpo central de la tesis consiste en la caracterización detallada de una PPO inusual, cuya inducción por estrés hídrico se describe por vez primera. Estas enzimas están ampliamente distribuidas en plantas, si bien su número es muy variable de unas especies a otras. Algunas, como nogal, tienen un único gen, mientras que Arabidopsis no tiene ninguno. En la última versión del genoma de chopo hemos identificado un total de 12 miembros bona fide, corrigiendo trabajos previos, y hemos caracterizado su expresión individual ante diferentes situaciones de estrés controlado y tratamientos hormonales. La isoforma antedicha es el único miembro de la familia que responde claramente a la deshidratación. También responde a salinidad y a la mayor parte de tratamientos hormonales ensayados, pero no a daño mecánico o tratamientos con metil jasmonato. Esto la diferencia de enzimas homólogas presentes en otras especies de plantas, que se han relacionado experimentalmente con estrés biótico. Los patrones de acumulación de transcritos en árboles adultos son compatibles con un papel protector frente a la sequía. La integración de nuestros estudios funcionales y filogenéticos sugiere que la familia ha sufrido un proceso reciente de diversificación y neofuncionalización, siendo la protección frente a deshidratación su papel primigenio. Aunque se conoce la actividad bioquímica in vitro de este tipo de enzimas, sus sustratos naturales son esencialmente una incógnita. Mediante expresión heteróloga en Escherichia coli BL21(DE3) hemos detectado que la enzima de chopo es capaz de oxidar L-DOPA a dopaquinona, siendo menos activa frente a otros sustratos. Por otra parte, hemos demostrado su localización cloroplástica mediante transformación transitoria de protoplastos con fusiones a la proteína fluorescente YFP. Mediante la obtención de plantas transgénicas de A. thaliana hemos demostrado que la enzima de chopo aumenta considerablemente la tolerancia in vivo frente a la deshidratación y al estrés salino. El análisis fenotípico detallado de las líneas transgénicas, combinando múltiples metodologías, nos ha permitido sustanciar que la tolerancia tiene una base compleja. Esta incluye una mayor protección del sistema fotosintético, una capacidad antioxidante muy incrementada y la acumulación de solutos osmoprotectores como la prolina. Los análisis metabolómicos nos han permitido asociar la expresión de la proteína a la síntesis de un flavano no descrito previamente en A. thaliana, vinculando la enzima de chopo con la síntesis de fenilpropanoides. También hemos observado alteraciones en los niveles hormonales que podrían subyacer a efectos pleiotrópicos con interés aplicado, como un aumento consistente del tamaño de la planta o el acortamiento del ciclo de crecimiento. Además de aportar datos novedosos sobre la funcionalidad in vivo de esta familia de oxidasas, los resultados de esta tesis demuestran que los árboles son sistemas de estudio interesantes para caracterizar nuevas estrategias de tolerancia al estrés abiótico con potencial aplicado. ABSTRACT Forests masses have an extraordinary importance for our society and the biosphere. Recent worldwide studies indicate that drought is the abiotic factor that affects more their growing and survival, followed by extreme temperatures and salinity. The understanding of how the arboreal species tolerate the stress has an evident practical interest, but their mechanisms have been studied much more in herbaceous species or with agronomic interest. However, considerable differences exist between them, as this thesis and recent studies show. Our study is focused on the molecular response of the poplar –the more developed forestry model system- to abiotic stress, specifically focused in the drought. Using a proteomic strategy and controlled treatments, we have identified main components in such response. Its participation has been validated through transcriptional analysis using qRT-PCR technology. We have identified proteins whose functional connection with tolerance mechanisms were already known, as molecular chaperones sHSP or enzymes that attenuate the oxidative stress, but also some proteins whose functional relationship with the stress is less clear or even novel, as polifenol oxidases (PPO), short chain deshidrogenases/reductases (SDR), or bicupines (BIC), among others. The central body of the thesis consists of the detailed characterization of an unsual PPO, whose induction due to drought stress is first described. These enzymes are thoroughly distributed in plants, but their number of members is very variable among species. Some of them, as the walnut tree, have a single gene, while Arabidopsis has none. We have identified a total of 12 members in the last version of the poplar genome, correcting previous works, and have characterized their individual expression against different situations of controlled stress and hormone treatments. The aforementioned isoform is the only member of the family that responds clearly to the drought. It also reacts to salinity and the majority of hormonal treatments tested, but it does not respond to mechanical damage or treatments with methyl jasmonate. This is the difference with homologue enzymes present in other plant species, which have been related experimentally with abiotic stress. The accumulation patterns of transcripts in adult trees are compatible with a protector role against drought. The integration of our functional and phylogenetic studies suggests that the family has suffered a recent process of diversification and neofunctionalization, being the protection against drought their original role. Although the in vitro biochemistry activity of this kind of enzymes is already known, their natural substracts are essentially a mystery. By means of heterologous expression of Escherichia coli BL21(DE3) we have detected that the enzyme of poplar is able to oxidize L-DOPA to dopaquinone, being less active against other substrates. Additionally, we have proven its chloroplastic location with transitory transformation of protoplasts with YFP protein fusion. By means of getting transgenic plants of A. thaliana, we have demonstrated that the poplar enzyme increases notably the in vivo tolerance against the drought and salinity stresses. The phenotypic analysis of the transgenic lines, and the use of multiple methodologies, allowed us to test the complexity of the tolerance. This includes a major protection of the photosynthetic system, a very increased antioxidant capacity and the accumulation of osmoprotectant solutes as the proline. The metabolic analysis has allowed to associate the protein expression with the synthesis of a Flavan non described previously in A. thalaiana, linking the enzyme of poplar with the synthesis of phenylpropanoids. We have observed alterations in the hormonal levels that could underlie pleiotropic effects with applied interest, as a consistent increase of the size of the plant and the reduction of the growth cycle. The results of this thesis, in addition to provide novel data about the in vivo functionality of the oxidase family, demonstrate that the trees are interesting systems of study to characterize new strategies of tolerance against abiotic stress with applied potential.

Health monitoring of a new hysteretic damper subjected to earthquakes on a shaking table

This paper presents the experimental results obtained by applying frequency-domain structural health monitoring techniques to assess the damage suffered on a special type of damper called Web Plastifying Damper (WPD). The WPD is a hysteretic type energy dissipator recently developed for the passive control of structures subjected to earthquakes. It consists of several I-section steel segments connected in parallel. The energy is dissipated through plastic deformations of the web of the I-sections, which constitute the dissipative parts of the damper. WPDs were subjected to successive histories of dynamically-imposed cyclic deformations of increasing magnitude with the shaking table of the University of Granada. To assess the damage to the web of the I-section steel segments after each history of loading, a new damage index called Area Index of Damage (AID) was obtained from simple vibration tests. The vibration signals were acquired by means of piezoelectric sensors attached on the I-sections, and non-parametric statistical methods were applied to calculate AID in terms of changes in frequency response functions. The damage index AID was correlated with another energy-based damage index-ID- which past research has proven to accurately characterize the level of mechanical damage. The ID is rooted in the decomposition of the load-displacement curve experienced by the damper into the so-called skeleton and Bauschinger parts. ID predicts the level of damage and the proximity to failure of the damper accurately, but it requires costly instrumentation. The experiments reported in this paper demonstrate a good correlation between AID and ID in a realistic seismic loading scenario consisting of dynamically applied arbitrary cyclic loads. Based on this correlation, it is possible to estimate ID indirectly from the AID, which calls for much simpler and less expensive instrumentation.

De novo assembly and annotation of a transcriptome during xylogenesis in Pinus canariensis Chr. Sm. ex DC

Nowadays, there is a great amount of genomic and transcriptomic data available about forest species, including ambitious projects looking for complete sequencing and annotation of different gymnosperm genomes [1, 2]. Pinus canariensis is an endemic conifer of the Canary Islands with re-sprouting capability and resilience against fire and mechanical damage, as result of an adaptation to volcanic environments. Additionally, this species has a high proportion of axial parenchyma compared with other conifers, and this tissue connects with radial parenchyma allowing transport of reserves. The most internal tracheids stop accumulating water [3], and get filled of resins and polyphenols synthesized by the axial parenchyma; this is the so-called ?torch-heartwood? [4], which avoids decay. This wood achieves very high prices due to its particular resistance to rot. These features make P. canariensis an interesting model species for the analysis of these developmental processes in conifers. In this study we aim to perform a complete transcriptome annotation during xylogenesis in Pinus canariensis, using next-generation sequencing (NGS) -Roche 454 pyrosequencing-, in order to provide a genomic resource for further analysis, including expression profiling and the identification of candidate genes for important adaptive features.

Testing equipment for the improvement of mechanical devices to minimize damage to fruit in commercial packing lines.

Damages -reduced in fruit packing lines is a major cause of grace reduction and quality loos in fresh marks: fruit. Fruit must be treated gently during in sir handling to improve their qualityin order to get a good price in a competitive market. The correct post-hardvest handling in fruit packing lines is a prerequisite to cut down the heavy post-harvest losses. Fruit packing lines must be evaluated, studying their design, the impacts applied to the fruits, the characteristics of the materials, etc. This study establishes the possibility of carrying out modifications and tests in a packing line during a long period of time. For this purpose, an experimental fruit packing line has been designed and located in the Agricultural Engineering Department of the Polythecnic University of Madrid with the aim of improving mechanical devices and fruit handling conditions to minimize damage to fruit. The experimental line consists of several transporting belts, one rollers transporter, one sizer, one elevator, one singularizer, and three trays to receive the calibrated fruit. The line has a length of 6.15 m and a width cf 1.9 m. Movement of the different components is regulated by electric motors with variable velocity electronically controlled. The height of the transfer points is variable and can be easily modified. The experimental line has been calibrated using two instrumented spheres IS 100 (8.8 cm Ø and6.2cm Ø). Average acceleration values obtained in all the transfers of the experimental line lay under 80 g's, although there is big variation for some of them being some values above 100 g's.

Study of the Mechanical Strength Improvement of Wafers for EWT Solar Cells by Chemical Etching after the Drilling Process

Mechanical stability of EWT solar cells deteriorates when holes are created in the wafer. Nevertheless, the chemical etching after the hole generation process improves the mechanical strength by removing part of the damage produced in the drilling process. Several sets of wafers with alkaline baths of different duration have been prepared. The mechanical strength has been measured by the ring on ring bending test and the failure stresses have been obtained through a FE simulation of the test. This paper shows the comparison of these groups of wafers in order to obtain an optimum value of the decreased thickness produced by the chemical etching

Curing, defects and mechanical performance of fiber-reinforced composites

Tradicionalmente, la fabricación de materiales compuestos de altas prestaciones se lleva a cabo en autoclave mediante la consolidación de preimpregnados a través de la aplicación simultánea de altas presiones y temperatura. Las elevadas presiones empleadas en autoclave reducen la porosidad de los componentes garantizando unas buenas propiedades mecánicas. Sin embargo, este sistema de fabricación conlleva tiempos de producción largos y grandes inversiones en equipamiento lo que restringe su aplicación a otros sectores alejados del sector aeronáutico. Este hecho ha generado una creciente demanda de sistemas de fabricación alternativos al autoclave. Aunque estos sistemas son capaces de reducir los tiempos de producción y el gasto energético, por lo general, dan lugar a materiales con menores prestaciones mecánicas debido a que se reduce la compactación del material al aplicar presiones mas bajas y, por tanto, la fracción volumétrica de fibras, y disminuye el control de la porosidad durante el proceso. Los modelos numéricos existentes permiten conocer los fundamentos de los mecanismos de crecimiento de poros durante la fabricación de materiales compuestos de matriz polimérica mediante autoclave. Dichos modelos analizan el comportamiento de pequeños poros esféricos embebidos en una resina viscosa. Su validez no ha sido probada, sin embargo, para la morfología típica observada en materiales compuestos fabricados fuera de autoclave, consistente en poros cilíndricos y alargados embebidos en resina y rodeados de fibras continuas. Por otro lado, aunque existe una clara evidencia experimental del efecto pernicioso de la porosidad en las prestaciones mecánicas de los materiales compuestos, no existe información detallada sobre la influencia de las condiciones de procesado en la forma, fracción volumétrica y distribución espacial de los poros en los materiales compuestos. Las técnicas de análisis convencionales para la caracterización microestructural de los materiales compuestos proporcionan información en dos dimensiones (2D) (microscopía óptica y electrónica, radiografía de rayos X, ultrasonidos, emisión acústica) y sólo algunas son adecuadas para el análisis de la porosidad. En esta tesis, se ha analizado el efecto de ciclo de curado en el desarrollo de los poros durante la consolidación de preimpregnados Hexply AS4/8552 a bajas presiones mediante moldeo por compresión, en paneles unidireccionales y multiaxiales utilizando tres ciclos de curado diferentes. Dichos ciclos fueron cuidadosamente diseñados de acuerdo a la caracterización térmica y reológica de los preimpregnados. La fracción volumétrica de poros, su forma y distribución espacial se analizaron en detalle mediante tomografía de rayos X. Esta técnica no destructiva ha demostrado su capacidad para analizar la microestructura de materiales compuestos. Se observó, que la porosidad depende en gran medida de la evolución de la viscosidad dinámica a lo largo del ciclo y que la mayoría de la porosidad inicial procedía del aire atrapado durante el apilamiento de las láminas de preimpregnado. En el caso de los laminados multiaxiales, la porosidad también se vio afectada por la secuencia de apilamiento. En general, los poros tenían forma cilíndrica y se estaban orientados en la dirección de las fibras. Además, la proyección de la población de poros a lo largo de la dirección de la fibra reveló la existencia de una estructura celular de un diámetro aproximado de 1 mm. Las paredes de las celdas correspondían con regiones con mayor densidad de fibra mientras que los poros se concentraban en el interior de las celdas. Esta distribución de la porosidad es el resultado de una consolidación no homogenea. Toda esta información es crítica a la hora de optimizar las condiciones de procesado y proporcionar datos de partida para desarrollar herramientas de simulación de los procesos de fabricación de materiales compuestos fuera de autoclave. Adicionalmente, se determinaron ciertas propiedades mecánicas dependientes de la matriz termoestable con objeto de establecer la relación entre condiciones de procesado y las prestaciones mecánicas. En el caso de los laminados unidireccionales, la resistencia interlaminar depende de la porosidad para fracciones volumétricas de poros superiores 1%. Las mismas tendencias se observaron en el caso de GIIc mientras GIc no se vio afectada por la porosidad. En el caso de los laminados multiaxiales se evaluó la influencia de la porosidad en la resistencia a compresión, la resistencia a impacto a baja velocidad y la resistencia a copresión después de impacto. La resistencia a compresión se redujo con el contenido en poros, pero éste no influyó significativamente en la resistencia a compresión despues de impacto ya que quedó enmascarada por otros factores como la secuencia de apilamiento o la magnitud del daño generado tras el impacto. Finalmente, el efecto de las condiciones de fabricación en el proceso de compactación mediante moldeo por compresión en laminados unidireccionales fue simulado mediante el método de los elementos finitos en una primera aproximación para simular la fabricación de materiales compuestos fuera de autoclave. Los parámetros del modelo se obtuvieron mediante experimentos térmicos y reológicos del preimpregnado Hexply AS4/8552. Los resultados obtenidos en la predicción de la reducción de espesor durante el proceso de consolidación concordaron razonablemente con los resultados experimentales. Manufacturing of high performance polymer-matrix composites is normally carried out by means of autoclave using prepreg tapes stacked and consolidated under the simultaneous application of pressure and temperature. High autoclave pressures reduce the porosity in the laminate and ensure excellent mechanical properties. However, this manufacturing route is expensive in terms of capital investment and processing time, hindering its application in many industrial sectors. This fact has driven the demand of alternative out-of-autoclave processing routes. These techniques claim to produce composite parts faster and at lower cost but the mechanical performance is also reduced due to the lower fiber content and to the higher porosity. Corrient numerical models are able to simulate the mechanisms of void growth in polymer-matrix composites processed in autoclave. However these models are restricted to small spherical voids surrounded by a viscous resin. Their validity is not proved for long cylindrical voids in a viscous matrix surrounded by aligned fibers, the standard morphology observed in out-of-autoclave composites. In addition, there is an experimental evidence of the detrimental effect of voids on the mechanical performance of composites but, there is detailed information regarding the influence of curing conditions on the actual volume fraction, shape and spatial distribution of voids within the laminate. The standard techniques of microstructural characterization of composites (optical or electron microscopy, X-ray radiography, ultrasonics) provide information in two dimensions and are not always suitable to determine the porosity or void population. Moreover, they can not provide 3D information. The effect of curing cycle on the development of voids during consolidation of AS4/8552 prepregs at low pressure by compression molding was studied in unidirectional and multiaxial panels. They were manufactured using three different curing cycles carefully designed following the rheological and thermal analysis of the raw prepregs. The void volume fraction, shape and spatial distribution were analyzed in detail by means of X-ray computed microtomography, which has demonstrated its potential for analyzing the microstructural features of composites. It was demonstrated that the final void volume fraction depended on the evolution of the dynamic viscosity throughout the cycle. Most of the initial voids were the result of air entrapment and wrinkles created during lay-up. Differences in the final void volume fraction depended on the processing conditions for unidirectional and multiaxial panels. Voids were rod-like shaped and were oriented parallel to the fibers and concentrated in channels along the fiber orientation. X-ray computer tomography analysis of voids along the fiber direction showed a cellular structure with an approximate cell diameter of 1 mm. The cell walls were fiber-rich regions and porosity was localized at the center of the cells. This porosity distribution within the laminate was the result of inhomogeneous consolidation. This information is critical to optimize processing parameters and to provide inputs for virtual testing and virtual processing tools. In addition, the matrix-controlled mechanical properties of the panels were measured in order to establish the relationship between processing conditions and mechanical performance. The interlaminar shear strength (ILSS) and the interlaminar toughness (GIc and GIIc) were selected to evaluate the effect of porosity on the mechanical performance of unidirectional panels. The ILSS was strongly affected by the porosity when the void contents was higher than 1%. The same trends were observed in the case of GIIc while GIc was insensitive to the void volume fraction. Additionally, the mechanical performance of multiaxial panels in compression, low velocity impact and compression after impact (CAI) was measured to address the effect of processing conditions. The compressive strength decreased with porosity and ply-clustering. However, the porosity did not influence the impact resistance and the coompression after impact strength because the effect of porosity was masked by other factors as the damage due to impact or the laminate lay-up. Finally, the effect of the processing conditions on the compaction behavior of unidirectional AS4/8552 panels manufactured by compression moulding was simulated using the finite element method, as a first approximation to more complex and accurate models for out-of autoclave curing and consolidation of composite laminates. The model parameters were obtained from rheological and thermo-mechanical experiments carried out in raw prepreg samples. The predictions of the thickness change during consolidation were in reasonable agreement with the experimental results.

A fatigue damage model for seismic response of RC structures

Numerous damage models have been developed in order to analyze seismic behavior. Among the different possibilities existing in the literature, it is very clear that models developed along the lines of continuum damage mechanics are more consistent with the definition of damage as a phenomenon with mechanical consequences because they include explicitly the coupling between damage and mechanical behavior. On the other hand, for seismic processes, phenomena such as low cycle fatigue may have a pronounced effect on the overall behavior of the frames and, therefore, its consideration turns out to be very important. However, most of existing models evaluate the damage only as a function of the maximum amplitude of cyclic deformation without considering the number of cycles. In this paper, a generalization of the simplified model proposed by Cipollina et al. [Cipollina A, López-Hinojosa A, Flórez-López J. Comput Struct 1995;54:1113–26] is made in order to include the low cycle fatigue. Such a model employs in its formulation irreversible thermodynamics and internal state variable theory.

A constitutive model for the in-plane mechanical behavior of nonwoven fabrics

A constitutive model is presented for the in-plane mechanical behavior of nonwoven fabrics. The model is developed within the context of the finite element method and provides the constitutive response for a mesodomain of the fabric corresponding to the area associated to a finite element. The model is built upon the ensemble of three blocks, namely fabric, fibers and damage. The continuum tensorial formulation of the fabric response rigorously takes into account the effect of fiber rotation for large strains and includes the nonlinear fiber behavior. In addition, the various damage mechanisms experimentally observed (bond and fiber fracture, interfiber friction and fiber pull-out) are included in a phenomenological way and the random nature of these materials is also taken into account by means of a Monte Carlo lottery to determine the damage thresholds. The model results are validated with recent experimental results on the tensile response of smooth and notched specimens of a polypropylene nonwoven fabric.

Mechanical Characterization of Multicrystalline Silicon Substrates for Solar Cell Applications

The possibility of using more economical silicon feedstock, i.e. as support for epitaxial solar cells, is of interest when the cost reduction and the properties are attractive. We have investigated the mechanical behaviour of two blocks of upgraded metallurgical silicon, which is known to present high content of impurities even after being purified by the directional solidification process. These impurities are mainly metals like Al and silicon compounds. Thus, it is important to characterize their effect in order to improve cell performance and to ensure the survival of the wafers throughout the solar value chain. Microstructure and mechanical properties were studied by means of ring on ring and three point bending tests. Additionally, elastic modulus and fracture toughness were measured. These results showed that it is possible to obtain marked improvements in toughness when impurities act as microscopic internal crack arrestors. However, the same impurities can be initiators of damage due to residual thermal stresses introduced during the crystallization process.

Modelization of low cycle fatigue damage in frames

Damage models based on the Continuum Damage Mechanics (CDM) include explicitly the coupling between damage and mechanical behavior and, therefore, are consistent with the definition of damage as a phenomenon with mechanical consequences. However, this kind of models is characterized by their complexity. Using the concept of lumped models, possible simplifications of the coupled models have been proposed in the literature to adapt them to the study of beams and frames. On the other hand, in most of these coupled models damage is associated only with the damage energy release rate which is shown to be the elastic strain energy. According to this, damage is a function of the maximum amplitude of cyclic deformation but does not depend on the number of cycles. Therefore, low cycle effects are not taking into account. From the simplified model proposed by Flórez-López, it is the purpose of this paper to present a formulation that allows to take into account the degradation produced not only by the peak values but also by the cumulative effects such as the low cycle fatigue. For it, the classical damage dissipative potential based on the concept of damage energy release rate is modified using a fatigue function in order to include cumulative effects. The fatigue function is determined through parameters such as the cumulative rotation and the total rotation and the number of cycles to failure. Those parameters can be measured or identified physically through the haracteristics of the RC. So the main advantage of the proposed model is the possibility of simulating the low cycle fatigue behavior without introducing parameters with no suitable physical meaning. The good performance of the proposed model is shown through a comparison between numerical and test results under cycling loading.

Mechanical segregation of apricot varieties and their ripeness levels at harvest

Some laboratory tests consisting on quasi-static compression and puncture forces carried out on twelve varieties of apricot during 1990 and 1991 were effective in sorting them. These mechanical properties show a high correlation w i th the ethylene production rate per fruit, so allowing to discriminate between ripeness levels at harvest. In this study it is also demonstrated that puncture seems to be the less variable mechanical test. The values (N/mm) obtained with it show a highly significant correlation with compression resistance and with quasi-static compression damage of the fruits.