Modal contribution and state space order selection in operational modal analysis

The estimation of modal parameters of a structure from ambient measurements has attracted the attention of many researchers in the last years. The procedure is now well established and the use of state space models, stochastic system identification methods and stabilization diagrams allows to identify the modes of the structure. In this paper the contribution of each identified mode to the measured vibration is discussed. This modal contribution is computed using the Kalman filter and it is an indicator of the importance of the modes. Also the variation of the modal contribution with the order of the model is studied. This analysis suggests selecting the order for the state space model as the order that includes the modes with higher contribution. The order obtained using this method is compared to those obtained using other well known methods, like Akaike criteria for time series or the singular values of the weighted projection matrix in the Stochastic Subspace Identification method. Finally, both simulated and measured vibration data are used to show the practicability of the derived technique. Finally, it is important to remark that the method can be used with any identification method working in the state space model.

Assessment of the requirement management process using a two-stage questionnaire

This research advocates the idea that although requirements management process is not carried out in many organizations there is some people within the organization that perform some requirements management practices. However, these practices are usually not documented and as consequence are not spread across the organization. This paper proposes an assessment methodology based on a two-stage questionnaire to identify which practices of the requirements management process are performed but not documented, which practices require to be prioritized and which are not implemented due to bad management or unawareness. In order to validate the assessment methodology, the questionnaire was applied to an industrial case study.

Determining practices achievement in the requirement management process using a two-stage questionnaire

This paper aims to obtain a baseline snapshot of the requirement management process using a two-stage questionnaire to identify both performed and non-performed CMMI practices. The questionnaire proposed in this paper may help with the assessment of the requirement management process, provide useful information related to the current state of the process, and indicate those practices that require immediate attention with the aim of begin a Software Process Improvement program.

Evaluation of three solar and daylighting control systems based on Calumen II, Ecotect and Radiance simulation programs to obtain an energy efficient and healthy interior in the experimental building prototype SDE10

Evaluation of three solar and daylighting control systems based on Calumen II, Ecotect and Radiance simulation programs to obtain an energy efficient and healthy interior in the experimental building prototype SDE10

E-Flow: A communication system for user notification in dynamic evacuation scenarios

Most of the current evacuation plans are based on static signaling, fixed monitoring infrastructure, and limited user notification and feedback mechanisms. These facts lead to lower situation awareness, in the case event of an emergency, such as blocked emergency exits, while delaying the reaction time of individuals. In this context, we introduce the E-Flow communication system, which improves the user awareness by integrating personal, mobile and fixed devices with the existing monitoring infrastructure. Our system broadens the notification and monitoring alternatives, in real time, among, safety staff, end-users and evacuation related devices, such as sensors and actuators.

Experiences and methodology in a multidisciplinary energy and architecture competition: Solar Decathlon Europe 2012

Solar Decathlon Europe is an international competition among universities which promotes interdisciplinary learning in engineering and architecture. Students from different disciplines participate in teams guided by several professors during a 29 month preparation period plus five weeks of on-site contest. The educational project involves designing, building and testing a solar energy house connected to the electrical grid with the strategy of maximizing self-consumption, supported by bioclimatic technologies and maintaining a low environmental footprint. It culminates in a on-site contest in which teams must assembly the house themselves, test it with ordinary real life tasks and finally disassembly it. The event has also a divulgative aim, trying to make students and visitors get interested in discovering the problems presented by real engineering and architecture applications. In addition, SDE covers R&D aspects in different fields such as energy efficiency, solar energy and bioclimatic architecture. This article presents the methodology followed during the SDE 2012 edition, in which more than 850 students participated. The obtained results show that the educational competition was a success according to the technical and professional ambitions of the students, most of them considering that their knowledge had increased in areas related to technical and multidisciplinary aspects.

Passive design strategies and performance of Net Energy Plus Houses

The first step in order to comply with the European Union goals of Near to Zero Energy Buildings is to reduce the energy consumption in buildings. Most of the building consumption is related to the use of active systems to maintain the interior comfort. Passive design strategies contribute to improve the interior comfort conditions, increasing the energy efficiency in buildings and reducing their energy consumption. In this work, an analysis of the passive strategies used in Net Energy Plus Houses has been made. The participating houses of the Solar Decathlon Europe 2012 competition were used as case studies. The passive design strategies of these houses were compared with the annual simulations, and the competition monitored data, especially during the Passive Monitored Period. The analysis included the thermal properties of the building envelope, geometric parameters, ratios and others passive solutions such as Thermal Energy Storage systems, evaporative cooling, night ventilation, solar gains and night sky radiation cooling. The results reflect the impact of passive design strategies on the houses' comfort and efficiency, as well as their influence in helping to achieve the Zero Energy Buildings category.

Some advances in extensive bridge monitoring using low cost dynamic characterization

Dynamic measurements will become a standard for bridge monitoring in the near future. This fact will produce an important cost reduction for maintenance. US Administration has a long term intensive research program in order to diminish the estimated current maintenance cost of US$7 billion per year over 20 years. An optimal intervention maintenance program demands a historical dynamical record, as well as an updated mathematical model of the structure to be monitored. In case that a model of the structure is not actually available it is possible to produce it, however this possibility does not exist for missing measurement records from the past. Current acquisition systems to monitor structures can be made more efficient by introducing the following improvements, under development in the Spanish research Project “Low cost bridge health monitoring by ambient vibration tests using wireless sensors”: (a) a complete wireless system to acquire sensor data, (b) a wireless system that permits the localization and the hardware identification of the whole sensor system. The applied localization system has been object of a recent patent, and (c) automatization of the modal identification process, aimed to diminish human intervention. This system is assembled with cheap components and allows the simultaneous use of a large number of sensors at a low placement cost. The engineer’s intervention is limited to the selection of sensor positions, probably based on a preliminary FE analysis. In case of multiple setups, also the position of a number of fixed reference sensors has to be decided. The wireless localization system will obtain the exact coordinates of all these sensors positions. When the selection of optimal positions is difficult, for example because of the lack of a proper FE model, this can be compensated by using a higher number of measuring (also reference) points. The described low cost acquisition system allows the responsible bridge administration to obtain historical dynamic identification records at reasonable costs that will be used in future maintenance programs. Therefore, due to the importance of the baseline monitoring record of a new bridge, a monitoring test just after its construction should be highly recommended, if not compulsory.

Efecto de la fertilización orgánica y mineral en las propiedades del suelo, la emisión de los principales gases de efecto invernadero y en las diferentes fases fenológicas del cultivo de café (Coffea arabica L.)

El cultivo de café es de gran importancia a nivel mundial (ICO, 2011), y en el Ecuador ha sido uno de los cultivos más importantes en la generación de divisas (COFENAC, 2011). Sin embargo en los sistemas productivos de este país se puede apreciar el uso inapropiado de fertilizantes, lo que conlleva a una pérdida de nutrientes, por lo que es importante estudiar las dosis adecuadas para la fertilización tanto mineral como orgánica. El objetivo del trabajo fue evaluar el efecto de la fertilización mineral y orgánica en diferentes dosis en un monocultivo de café en la provincia de Loja, sobre las propiedades del suelo, la emisión de los principales gases que provocan el efecto invernadero y la fenología y productividad del cultivo. En la provincia de Loja (Ecuador) se seleccionó un área de 2.520 m2 en la que se establecieron 21 parcelas de café arábigo (Coffea arabica L.) var. caturra y se aplicó tres tratamientos con tres repeticiones de fertilización mineral y tres orgánicos con dosis: bajas minerales (MIN 1= 157 Kg NPK ha-1 año-1 para el primer año y 425 Kg NPK ha-1 año-1 para el segundo año), medias minerales (MIN 2= 325 Kg NPK ha-1 año-1 para el primer año y 650 Kg NPK ha-1 año-1 en el segundo año) y altas minerales (MIN 3= 487 y 875 Kg NPK ha-1 año-1 para el primer y segundo año respectivamente), bajas orgánicas (ORG 1= 147 Kg NPK ha-1 año-1 en el primer año y 388 Kg NPK ha-1 año-1 en el año dos), medias orgánicas (ORG 2= 265 Kg NPK ha-1 año-1 para el primer año y 541 Kg NPK ha-1 año-1 en el segundo año), altas orgánicas (ORG 3= 368 Kg NPK ha-1 año-1 para el primer año y 727 Kg NPK ha-1 año-1 en el segundo año) y fertilización cero (TES = sin fertilización). Se usó urea, roca fosfórica y muriato de potasio en la fertilización mineral y humus (Bioabor) en la orgánica, más un tratamiento testigo, cada tratamiento tuvo tres repeticiones. El tiempo de evaluación de los fertilizantes aplicados fue de dos años consecutivos, la fertilización se la realizó dos veces por año y en base a análisis del suelo y demandas nutricionales del cultivo. para determinar las características del suelo se realizó muestreos de suelos en cada parcela a una profundidad de 20 cm de estas muestras los parámetro iniciales determinados fueron: color (Munsell), textura (método del hidrómetro), pH (relación 1:2,5 suelo-agua), Materia orgánica (Walkey y Black), Nitrógeno (Micro Kjendahl), Fósforo (Bray y Kurtz), Potasio (Olsen), estos procesos se repitieron cada seis meses para poder evaluar los cambios de que se producen debido a la fertilización mineral y orgánica en el cultivo. Las emisiones de gases efecto invernadero desde el suelo al ambiente se determinaron por el método de cámara cerrada (Rondón, 2000) y la concentración por cromatografía de gases. Las mediciones fisiológicas (altura de planta, ancho de copa, grosor de tallo y producción) se las evaluó cada dos meses, a excepción de la producción que fue anual al término de cada cosecha. Además se realizó el análisis económico de la productividad del cultivo. El análisis estadístico de datos se lo realizó con el programa SPSS v. 17.0. Las medias fueron comprobadas mediante ANOVAS de un factor con test de Tukey (P < 0,05). El beneficio económico se estimó en términos de ingresos y gastos totales que se presentaron en el ensayo. Los resultados obtenidos al término del ensayo indican que los tratamientos MIN 2 y MIN 3 produjeron cambios más significativos en comparación con los otros tratamientos establecidos en la mejora de fertilidad del suelo, el pH ha sido menos afectado en la acidificación en comparación con los tratamientos orgánicos que se han acidificado mayormente; la materia orgánica (MO) tuvo incrementos considerablemente bueno en estos dos tratamientos, sin embargo fueron superados por los tratamientos de fertilización orgánica; el nitrógeno total (Nt )y el potasio (K) también presentaron mejores valores al termino del ensayo y el fósforo (P) mostro incrementos buenos aunque un poco menores que los de los tratamientos ORG 2 y ORG 3. En lo que respecta a las emisiones de gases efecto invernadero, los flujos acumulados de óxido nitroso (N2O) en los dos años han aumentado en todos los tratamientos en comparación con el tratamiento Testigo, pero de manera considerable y con mayores flujos en el tratamiento MIN 3 y MIN 2 que se podrían considerarse los de mayor contaminación por N2O al ambiente lo que se le atribuye a las dosis de fertilización mineral aplicadas en el periodo de investigación, los tratamiento MIN 1 y todos los tratamientos orgánicos muestran menores emisiones al ambiente. Las emisiones de metano (CH4) no muestran mayores diferencias de emisiones entre tratamientos, siendo los mayores emisores los tratamientos ORG 3 y ORG 2 posiblemente debido al abono orgánico y añadido al suelo; para las emisiones de dióxido de carbono (CO2) de manera similar al CH4 el tratamiento ORG 3 fue el que presento mayores emisiones, los flujos de CO2 al ambiente de los otros tratamientos fueron menores y no presentaron diferencias significativas entre ellos. La variables fisiológicas en todos los casos apoyaron al desarrollo de las plantas de café, esto al ser comparadas con el tratamiento Testigo, sin embargo las que alcanzaron las mayores altitudes, anchos de copas y diámetro de tallo fueron las plantas del tratamiento MIN 3, seguido del MIN 3, no mostrando significancia entre ellos, y para los tratamientos orgánicos el que presento muy buenos resultados en estas variables ha sido el ORG 3, el cual no presento diferencias significativas con el MIN 2, lo cual comprueba que la fertilización mineral es más efectiva en este caso frente a la orgánica. Para el primer año de producción el tratamiento mineral con fertilización MIN 3 es el que obtuvo mayor producción no presentando diferencia estadística con el tratamiento con el MIN 2, no obstante fueron significativamente mayores que los otros tratamientos. Vale indicar que también el tratamiento MIN 1 y el tratamiento ORG 3 han presentado una producción considerable de café no mostrando diferencias estadísticas entre ellos. Para el segundo año la producción el cultivo mostró mayores rendimientos que el primer año de evaluación en todos los tratamientos, esto debido a la fisiología propia del cultivo y por otra parte se atribuye a la adición de fertilizantes que se ha realizado durante todo el ensayo; de manera similar al anterior los tratamientos MIN 3 y MIN 2 obtuvieron mejores rendimientos, no enseñando diferencias estadísticas significativas entre ellos, no obstante el tratamiento mineral dosis MEDIA no presentó significancia estadística con el ORG 3. El benéfico económico ha resultado mayor en el tratamiento MIN 3 y MIN 2, aunque el tratamiento MIN 2, es el que obtiene la mejor relación costo-beneficio; los tratamientos ORG 2 y ORG 3 y Testigo has producido beneficios negativos para el productor. En cuanto a la parte ambiental se considera que los mejores tratamientos en cuanto ha cuidado ambiental serían los tratamientos MIN 1 y ORG 1, sin embargo a nivel de producción y rentabilidad para el productor baja. ABSTRACT Coffee growing has great importance worldwide (ICO, 2011), and in Ecuador, it has been one of the most important crops to generate income (COFENAC, 2011). However, in the productive systems of this country, the inappropriate use of fertilizers has been observed which produces loss of nutrients, thus it is important to study suitable doses for mineral and organic fertilizing. The purpose of the study was to evaluate the effect of mineral and organic fertilizing at different doses in a coffee monoculture in the province of Loja on soil characteristics, emission of the main gasses that produce the greenhouse effect and the phenology and productivity of crops. In the province of Loja (Ecuador) an area of 2.520 m2 was chosen, where 21 plots of Arabica coffee (Coffea arabica L.), the caturra variety were cultivated and three treatments with three repetitions each one for mineral and organic fertilization were used with doses that ranged from: mineral low (MIN 1= 157 Kg NPK ha-1 año-1 for the first year y 425 Kg NPK ha-1 año-1 for the second year), mineral medium (MIN 2= 325 Kg NPK ha-1 año-1 for the first year y 650 Kg NPK ha-1 año-1 I the second year) y mineral high (MIN 3= 487 y 875 Kg NPK ha-1 año-1 for the first and second year respectively), organic low (ORG 1= 147 Kg NPK ha-1 año-1 in the first year y 388 Kg NPK ha-1 año-1 in the second year), organics medium (ORG 2= 265 Kg NPK ha-1 año-1 for the first year y 541 Kg NPK ha-1 año-1 in the second year), organics high (ORG 3= 368 Kg NPK ha-1 año-1 for the first year and 727 Kg NPK ha-1 año-1 in the second year) y fertilization zero (TES = no fertilization).; urea, phosphoric rock and muriate of potash were used in the mineral fertilization and humus (Bioabor) in the organic, plus a blank treatment. Time to evaluate the applied fertilizers was for two consecutive years, fertilization was done twice per year based on soil analysis and nutritional requirements of the crops. In order to determine the characteristics of the soil, samples of soil in each plot with a depth of 20 cm were done; from these samples, the determined initial parameters were: color (Munsell), texture (hydrometer method), pH (soil-water 1:2,5 relation), organic matter (Walkey y Black), nitrogen (Micro Kjendahl), phosphorus (Bray y Kurtz), potassium (Olsen); these processes were repeated each six months in order to evaluate the changes that are produced due to mineral and organic fertilization in the crops. The emissions of greenhouse gasses from the soil to the atmosphere were determined by using enclosure method (Rondón, 2000) and the concentration, by using gas chromatography during the whole testing. The physiological measures (plant height, width of the top of the tree, thickness of the stem and production) were evaluated each two months, except for production which was annual at the end of each harvest. Moreover, the economic analysis of the productivity of the crops was done. The statistical analysis of the data was done using SPSS v. 17.0. The means were proved by ANOVAS with a factor of a Tukey test (P < 0,05). The economic benefit was estimated in terms of incomes and total expenses which were presented in the essay. The results obtained at the end of the essay show that the MIN 2 and MIN 3 treatments produced more meaningful changes in comparison with the other treatments used to improve soil fertility; pH was less affected in the acidification compared with the organic treatments which were greatly acidified; organic matter (MO) had increased considerably in these two treatments; however, they were surpassed by the organic treatments of fertilization; total nitrogen (Nt) and potassium (K) also presented better results at the end of the essay and phosphorus (P) showed good increasing figures although a little lower compared with ORG 2 and ORG 3 treatments. Regarding the emission of the greenhouse gasses, the fluxes accumulated from nitrous oxide (N2O) in two years increased in all the treatments in comparison with the blank treatment, but in a greater form and with higher fluxes in the MIN 3 and MIN 2 treatments which can be considered as the ones with greater contamination of N2O in the atmosphere, this can be due to the applied mineral doses to fertilize during the process; MIN 1 treatments and all the organic ones showed lower emission to the atmosphere. Methane emissions (CH4) did not show major differences in emissions in the treatments, being the greater emissions the ORG 3 and ORG 2 treatments; this is possibly due to the organic compost added to the soil; regarding carbon dioxide (CO2) emissions, in a similar way to CH4, the ORG 3 treatment was the one that presented greater emissions, the CO2 emissions to the atmosphere in the other treatments were lower and did not present meaningful differences among them. The physiological variables in all the cases helped coffee crops grow, this was observed when compared with the blank treatment; however, plants that reached the greatest height, width of top and diameter of stem were the plants of the MIN 3 treatment, followed by MIN 3, which did not show much significance among them, and for the organic treatments, the one that presented great results in these variables was ORG 3, which did not show meaningful differences compared with MIN 2, which proves that mineral fertilization is more effective in this case compared with the organic. In the first year of production, the mineral treatment with MIN 3 fertilization obtained greater production and thus did not show statistical difference with MIN 2 treatment, although the other treatments were greater. It is worth mentioning that MIN 1 treatment and ORG 3 treatment presented a meaningful production of coffee, not showing statistical differences among them. For the second year, the production of the crops showed greater profits than in the first year of evaluation in all the treatments, this was due to the physiological properties of the crops and on the other hand, it might be due to the addition of fertilizers during the whole essay; in a similar way, MIN 3 and MIN 2 performed better, not showing greater statistical differences among them, although the mineral treatment MEDIUM doses did not show statistical difference compared with ORG 3. The economic benefit was greater in the MIN 3 and MIN 2 treatments, although MIN 2 treatment is the one that shows the best cost-benefit ratios; ORG 2 and ORG 3 treatments and the blank produced negative benefits for the producer. Regarding the environment, the best treatments to care for the atmosphere are considered to be MIN 1 and ORG 1 treatments; however, regarding production volume and profitability they were low for the producer.

Application of user-centered design in the development of an atomated/assisted testing system for self-service devices

Automated Teller Machines (ATMs) are sensitive self-service systems that require important investments in security and testing. ATM certifications are testing processes for machines that integrate software components from different vendors and are performed before their deployment for public use. This project was originated from the need of optimization of the certification process in an ATM manufacturing company. The process identifies compatibility problems between software components through testing. It is composed by a huge number of manual user tasks that makes the process very expensive and error-prone. Moreover, it is not possible to fully automate the process as it requires human intervention for manipulating ATM peripherals. This project presented important challenges for the development team. First, this is a critical process, as all the ATM operations rely on the software under test. Second, the context of use of ATMs applications is vastly different from ordinary software. Third, ATMs’ useful lifetime is beyond 15 years and both new and old models need to be supported. Fourth, the know-how for efficient testing depends on each specialist and it is not explicitly documented. Fifth, the huge number of tests and their importance implies the need for user efficiency and accuracy. All these factors led us conclude that besides the technical challenges, the usability of the intended software solution was critical for the project success. This business context is the motivation of this Master Thesis project. Our proposal focused in the development process applied. By combining user-centered design (UCD) with agile development we ensured both the high priority of usability and the early mitigation of software development risks caused by all the technology constraints. We performed 23 development iterations and finally we were able to provide a working solution on time according to users’ expectations. The evaluation of the project was carried out through usability tests, where 4 real users participated in different tests in the real context of use. The results were positive, according to different metrics: error rate, efficiency, effectiveness, and user satisfaction. We discuss the problems found, the benefits and the lessons learned in the process. Finally, we measured the expected project benefits by comparing the effort required by the current and the new process (once the new software tool is adopted). The savings corresponded to 40% less effort (man-hours) per certification. Future work includes additional evaluation of product usability in a real scenario (with customers) and the measuring of benefits in terms of quality improvement.

Energy efficiency evaluation of zero energy houses

Given the global energy and environmental situation, the European Union has been issuing directives with increasingly demanding requirements in term of the energy efficiency in buildings. The international competition of sustainable houses, Solar Decathlon Europe (SDE), is aligned with these European objectives. SDE houses are low energy solar buildings that must reach the near to zero energy houses’ goal. In the 2012 edition, in order to emphasize its significance, the Energy Efficiency Contest was added. SDE houses’ interior comfort, functioning and energy performance is monitored. The monitoring data can give an idea about the efficiency of the houses. However, a jury comprised by international experts is responsible for carrying out the houses energy efficiency evaluation. Passive strategies and houses services are analyzed. Additionally, the jury's assessment has been compared with the behavior of the houses during the monitoring period. Comparative studies make emphasis on the energy aspects, houses functioning and their interior comfort. Conclusions include thoughts related with the evaluation process, the results of the comparative studies and suggestions for the next competitions.

Almacenamiento de energía térmica por calor latente en los edificios: bases para la optimización de aplicaciones pasivas, opacas y traslúcidas

La principal motivación para la elección del tema de la tesis es nuestra realidad energética y ambiental. Y más específicamente, la necesidad urgente de dar una respuesta a esta realidad desde el sector de la edificación. Por lo que, el trabajo parte de la búsqueda de soluciones pasivas que ayuden a la reducción del consumo energético y de las emisiones de C02 de los edificios, tanto nuevos como existentes. El objeto de estudio son aplicaciones innovadoras, basadas en el uso de materiales reactivos, con un efecto térmico de memoria bidireccional. La energía es un elemento imprescindible para el desarrollo. Sin embargo, el modelo energético predominante, basado principalmente en la utilización de combustibles de origen fósil, es uno de los importantes responsables del deterioro ambiental que sufre el planeta. Además, sus reservas son limitadas y están concentradas en unas pocas regiones del mundo, lo que genera problemas de dependencia, competitividad y de seguridad de suministro. Dado el gran potencial de ahorro energético del sector de la edificación, la Unión Europea en sus directivas enfatiza la necesidad de mejorar la eficiencia energética de los edificios. Añadiendo, además, la obligatoriedad de desarrollar edificios “energía casi nula”, cuyo prerrequisito es tener un muy alto rendimiento energético. En España, los edificios son responsables del 31% del consumo de energía primaria. La mayor parte de este consumo se relaciona a la utilización de sistemas activos de acondicionamiento. Una medida efectiva para reducir la demanda es mejorar la envolvente. Sin embargo, hay que buscar estrategias adicionales para aumentar aún más la eficiencia de los edificios nuevos y existentes. Para los climas de España, el uso de la inercia térmica ha probado ser una estrategia válida. Sin embargo, su funcionamiento está vinculado al peso y al volumen de los materiales utilizados. Esto limita sus posibilidades en la rehabilitación energética y en los nuevos edificios basados en la construcción ligera. Una alternativa es el uso de aplicaciones de almacenamiento térmico por calor latente, utilizando materiales de cambio de fase (PCM). Los PCM son sustancias con un muy alto calor de fusión, capaces de almacenar una gran cantidad de energía térmica sin requerir aumentos significativos de peso o volumen. Estas características los hacen idóneos para reducir el consumo relacionado con el acondicionamiento térmico, en edificios nuevos y existentes. En la parte preliminar de la investigación, se encontró que para lograr un aprovechamiento óptimo de las aplicaciones con PCM es necesario tener un conocimiento profundo de su funcionamiento y de las variables del sistema. De ahí que el objetivo principal de la presente tesis sea: establecer las bases para la optimizatión integral de las aplicaciones con almacenamiento de energía térmica por calor latente, identificando y validando sus variables más relevantes. La investigación consta de tres partes. La primera, documental, sistematizando y jerarquizando la información científica publicada; la segunda, numérica, basada en un análisis paramétrico de una aplicación con PCM, utilizando simulaciones térmicas; y la tercera, experimental, monitorizando el funcionamiento térmico y energético de diferentes aplicaciones con PCM en módulos a escala real. Los resultados brindan un más profundo entendimiento del funcionamiento de las aplicaciones evaluadas. Han permitido identificar sus variables relevantes, cuantificar su influencia, y determinar condiciones óptimas para su utilización así como situaciones en las que sería muy difícil justificar su uso. En el proceso, se realizó la caracterización térmica y energética de aplicaciones con PCM, tanto opacas como traslúcidas. Además, se ha encontrado que las aplicaciones con PCM son capaces de aumentar la eficiencia energética inclusive en recintos con diseños optimizados, demostrando ser una de las estrategias adecuadas para lograr el muy alto desempeño energético requerido en los edificios energía nula. ABSTRACT The main motivation for choosing the theme of the thesis is our energy and environmental reality. And more specifically, the urgent need to respond to this reality from the building sector. This is why, the work start with the search of passive solutions that help reduce energy consumption and C02 emissions of buildings, in both new and existing ones. The object of study is innovative applications based on the use of responsive materials, with bidirectional thermal memory. Energy is an essential element for development. However, the predominant energy model, based primarily on the use of fossil fuels, is one of the major responsible for the environmental deterioration of the planet, the cause of most of the CO2 emissions. Furthermore, reserves of fossil fuels are limited and are concentrated in a few regions of the world, which creates issues related to dependency, competitiveness, and security of supply. Given the large potential for energy savings in the building sector, the European Union in its directives emphasizes the need to improve energy efficiency in buildings. Also, adding the obligation to develop "nearly zero energy" buildings, whose first prerequisite is to achieve a very high energy efficiency. In Spain, buildings are responsible for 31% of primary energy consumption and most of this consumption is related to the used of HVAC systems. One of the most effective measures to reduce demand is to improve the envelope. However, it is necessary to look for additional strategies to further increase the efficiency of new and existing buildings. For the predominant climates in Spain, use of the thermal inertia may be a valid strategy. Nevertheless, its operation is linked to weight and volume of the materials used. This limits their possibilities in the existing buildings energy retrofitting and in the new buildings based on lightweight construction. An alternative is the use of latent heat thermal energy storage applications (LHTES), using phase change materials (PCM). PCM are substances with a high heat of fusion, capable of storing a large amount of thermal energy without requiring significant increases in weight or volume. These features make them ideal for reducing energy consumption associated with thermal conditioning in both new and existing buildings. In the preliminary part of the investigation, it was found that to get optimum utilization of the PCM applications is needed to have a deep understanding of its operation and, in particular, how the system variables affect its performance. Hence, the main objective of this thesis is: to establish the basis for the integral optimization of applications with latent heat thermal energy storage, identifying and validating the most relevant variables. The research comprises of three parts. The first, documentary, systematizing and prioritizing published scientific information. The second, numeric, based on a parametric analysis of an application PCM using thermal simulations. The third, experimental, monitoring the thermal and energy performance of different applications with PCM on real scale test cells. The results provide a complete understanding of the functioning of the evaluated LHTES application. They have allowed to identify their relevant variables, quantify their influence and determine optimum conditions for use as well as situations where it would be very difficult to justify its use. In the process, it was carried out the power and thermal characterization of various opaque and translucent PCM applications. Furthermore, it has been found that applications with PCM can increase the energy efficiency, even in buildings with optimized designs; proving to be one of the appropriate measures to achieve the high energy performance required in zero energy buildings.