Effects of gamma-Ray radiation on magnetic properties of NdFeB and SmCo permanent magnets for space applications

Several samples of NdFeB and SmCo permanent magnets have been irradiated with gamma rays up to different total irradiation doses until 1Mrad(Si). Magnetic properties of the samples have been measured at different temperatures before and after irradiation. The modifications of the magnetic parameters are presented. From these results it is highlighted which permanent magnets show more resistance to radiation and are more suitable to be included in devices for space applications or high radiation environments.

Calculation Methodology and Fabrication Procedures for Particle Accelerator Strip-Line Kickers: Application to the CTF3 Combiner Ring Extraction Kicker and TL2 Tail Clippers

A particle accelerator is any device that, using electromagnetic fields, is able to communicate energy to charged particles (typically electrons or ionized atoms), accelerating and/or energizing them up to the required level for its purpose. The applications of particle accelerators are countless, beginning in a common TV CRT, passing through medical X-ray devices, and ending in large ion colliders utilized to find the smallest details of the matter. Among the other engineering applications, the ion implantation devices to obtain better semiconductors and materials of amazing properties are included. Materials supporting irradiation for future nuclear fusion plants are also benefited from particle accelerators. There are many devices in a particle accelerator required for its correct operation. The most important are the particle sources, the guiding, focalizing and correcting magnets, the radiofrequency accelerating cavities, the fast deflection devices, the beam diagnostic mechanisms and the particle detectors. Most of the fast particle deflection devices have been built historically by using copper coils and ferrite cores which could effectuate a relatively fast magnetic deflection, but needed large voltages and currents to counteract the high coil inductance in a response in the microseconds range. Various beam stability considerations and the new range of energies and sizes of present time accelerators and their rings require new devices featuring an improved wakefield behaviour and faster response (in the nanoseconds range). This can only be achieved by an electromagnetic deflection device based on a transmission line. The electromagnetic deflection device (strip-line kicker) produces a transverse displacement on the particle beam travelling close to the speed of light, in order to extract the particles to another experiment or to inject them into a different accelerator. The deflection is carried out by the means of two short, opposite phase pulses. The diversion of the particles is exerted by the integrated Lorentz force of the electromagnetic field travelling along the kicker. This Thesis deals with a detailed calculation, manufacturing and test methodology for strip-line kicker devices. The methodology is then applied to two real cases which are fully designed, built, tested and finally installed in the CTF3 accelerator facility at CERN (Geneva). Analytical and numerical calculations, both in 2D and 3D, are detailed starting from the basic specifications in order to obtain a conceptual design. Time domain and frequency domain calculations are developed in the process using different FDM and FEM codes. The following concepts among others are analyzed: scattering parameters, resonating high order modes, the wakefields, etc. Several contributions are presented in the calculation process dealing specifically with strip-line kicker devices fed by electromagnetic pulses. Materials and components typically used for the fabrication of these devices are analyzed in the manufacturing section. Mechanical supports and connexions of electrodes are also detailed, presenting some interesting contributions on these concepts. The electromagnetic and vacuum tests are then analyzed. These tests are required to ensure that the manufactured devices fulfil the specifications. Finally, and only from the analytical point of view, the strip-line kickers are studied together with a pulsed power supply based on solid state power switches (MOSFETs). The solid state technology applied to pulsed power supplies is introduced and several circuit topologies are modelled and simulated to obtain fast and good flat-top pulses.

Effect of strain and magnetic field on the critical current and electric resistance of the joints between HTS coated conductors

Engineering of devices and systems such as magnets, fault current limiters or cables, based on High Temperature Superconducting wires requires a deep characterization of the possible degradation of their properties by handling at room temperature as well as during the service life thus establishing the limits for building up functional devices and systems. In the present work we report our study regarding the mechanical behavior of spliced joints between commercial HTS coated conductors based on YBCO at room temperature and service temperature, 77 K. Tensile tests under axial stress and the evolution of the critical current and the electric resistance of the joints have been measured. The complete strain contour for the tape and the joint has been obtained by using Digital Image Correlation. Also, tensile tests under external magnetic field have been performed and the effect of the applied field on the critical current and the electric resistance of the joints has been studied. Finally, a preliminary numerical study by means of Finite Element Method (FEM) of the mechanical behavior of the joints between commercial HTS is presented.

Effect of strain and magnetic field on the critical current and electric resistance of the joints between HTS coated conductors

Engineering of devices and systems such as magnets, fault current limiters or cables, based on High Temperature Superconducting wires requires a deep characterization of the possible degradation of their properties by handling at room temperature as well as during the service life thus establishing the limits for building up functional devices and systems. In the present work we report our study regarding the mechanical behavior of spliced joints between commercial HTS coated conductors based on YBCO at room temperature and service temperature, 77 K. Tensile tests under axial stress and the evolution of the critical current and the electric resistance of the joints have been measured. The complete strain contour for the tape and the joints has been obtained by using Digital Image Correlation. Also, tensile tests under external magnetic field have been performed and the effect of the applied field on the critical current and the electric resistance of the joints has been studied. Additionally, fatigue tests under constant cyclic stress and loading-unloading ramps have been carried out in order to evaluate the electromechanical behavior of the joints and the effect of maximum applied stress on the critical current. Finally, a preliminary numerical study by means of the Finite Element Method (FEM) of the electromechanical behavior of the joints between commercial HTS is presented.

Evaluation of preisach model of hysteresis to model superconductors

The Large Hadron Collider is the world’s largest and most powerful particle accelerator. The project is divided in phases. The first one goes from 2009 until 2020. The second phase will consist of the implementation of upgrades. One of the upgrades is to increase the ratio of collision, the luminosity. This objective is the main of one of the most important projects which is carrying out the upgrades: Hi-Lumi LHC project. Increasing luminosity could be done by using a new material in the superconductor magnets placed at the interaction points: Nb3Sn, instead of NbTi, the one being used right now. Before implementing it many aspects should be analysed. One of them is the induction magnetic field quality. The tool used so far has been ROXIE, software developed at CERN by S. Russenschuck. One of the main features of the programme is the time-transient analysis, which is based on three mathematical models. It is quite precise for fields above 1.5 Tesla. However, they are not very accurate for lower fields. Therefore the aim of this project is to evaluate a more accurate model: Classical Preisach Model of Hysteresis, in order to better analyse induced field quality in the new material Nb3Sn. Resumen: El Gran Colisionador de Hadrones es el mayor acelerador de partículas circular del mundo. Se trata de uno de los mayores proyectos de investigación. La primera fase de funcionamiento comprende desde 2009 a 2020, cuando comenzará la siguiente fase. Durante el primer periodo se han pensado mejoras para que puedan ser implementadas en la segunda fase. Una de ellas es el aumento del ratio de las colisiones entre protones por choque. Este es el principal objetivo de uno de los proyectos que está llevando a cabo las mejoras a ser implementadas en 2020: Hi- Lumi LHC. Se cambiarán los imanes superconductores de NbTi de las dos zonas principales de interacción, y se sustituirán por imanes de Nb3Sn. Esta sustituciónn conlleva un profundo estudio previo. Entre otros, uno de los factores a analizar es la calidad del campo magnético. La herramienta utilizada es el software desarrollado por S. Russenschuck en el CERN llamado ROXIE. Está basado en tres modelos de magnetización, los cuales son precisos para campos mayores de 1.5 T. Sin embargo, no lo son tanto para campos menores. Con este proyecto se pretende evaluar la implementación de un cuarto modelo, el modelo clásico de histéresis de Preisach que permita llevar a cabo un mejor análisis de la calidad del campo inducido por el futuro material a utilizar en algunos de los imanes.

Mechanical behavior of 2G REBCO HTS at 77 and 300 K

El gran esfuerzo realizado durante la última década con el fin de integrar los diferentes materiales superconductores en el campo de los sistemas eléctricos y en otras aplicaciones tecnológicas ha dado lugar a un campo de investigación amplio y prometedor. El comportamiento eléctrico de los Superconductores de Alta Temperatura (SAT) crítica (masivo y cintas) depende de diferentes parámetros desde su fabricación hasta la aplicación final con imanes o cables. Sin embargo, las aplicaciones prácticas de estos materiales están fuertemente vinculadas con su comportamiento mecánico tanto a temperatura ambiente (manipulación durante fabricación o instalación) como a temperaturas criogénicas (condiciones de servicio). En esta tesis se ha estudiado el comportamiento mecánico de materiales masivos y cintas de alta temperatura crítica a 300 y 77 K (utilizando nitrógeno líquido). Se han obtenido la resistencia en flexión, la tenacidad de fractura y la resistencia a tracción a la temperatura de servicio y a 300 K. Adicionalmente, se ha medido la dureza mediante el ensayo Vickers y nanoindentación. El módulo Young se midió mediante tres métodos diferentes: 1) nanoindentación, 2) ensayos de flexión en tres puntos y 3) resonancia vibracional mediante grindosonic. Para cada condición de ensayo, se han analizado detalladamente las superficies de fractura y los micromecanismos de fallo. Las propiedades mecánicas de los materiales se han comparado con el fin de entender la influencia de las técnicas de procesado y de las características microestructurales de los monocristales en su comportamiento mecánico. Se ha estudiado el comportamiento electromecánico de cintas comerciales superconductoras de YBCO mediante ensayos de tracción y fatiga a 77 y 300 K. El campo completo de deformaciones en la superficie del material se ha obtenido utilizando Correlación Digital de Imágenes (DIC, por sus siglas en inglés) a 300 K. Además, se realizaron ensayos de fragmentación in situ dentro de un microscopio electrónico con el fin de estudiar la fractura de la capa superconductora y determinar la resistencia a cortante de la intercara entre el substrato y la capa cerámica. Se ha conseguido ver el proceso de la fragmentación aplicando tensión axial y finalmente, se han implementado simulaciones mediante elementos finitos para reproducir la delaminación y el fenómeno de la fragmentación. Por último, se han preparado uniones soldadas entre las capas de cobre de dos cintas superconductoras. Se ha medido la resistencia eléctrica de las uniones con el fin de evaluar el metal de soldadura y el proceso. Asimismo, se ha llevado a cabo la caracterización mecánica de las uniones mediante ensayos "single lap shear" a 300 y 77 K. El efecto del campo magnético se ha estudiado aplicando campo externo hasta 1 T perpendicular o paralelo a la cinta-unión a la temperatura de servicio (77 K). Finalmente, la distribución de tensiones en cada una de las capas de la cinta se estudió mediante simulaciones de elementos finitos, teniendo en cuenta las capas de la cinta mecánicamente más representativas (Cu-Hastelloy-Cu) que influyen en su comportamiento mecánico. The strong effort that has been made in the last years to integrate the different superconducting materials in the field of electrical power systems and other technological applications led to a wide and promising research field. The electrical behavior of High Temperature Superconducting (HTS) materials (bulk and coated conductors) depends on different parameters since their processing until their final application as magnets or cables. However, practical applications of such materials are strongly related with their mechanical performance at room temperature (handling) as well as at cryogenic temperatures (service conditions). In this thesis, the mechanical behavior of HTS bulk and coated conductors was investigated at 300 and 77 K (by immersion in liquid nitrogen). The flexural strength, the fracture toughness and the tensile strength were obtained at service temperature as well as at 300 K. Furthermore, their hardness was determined by Vickers measurements and nanoindentation and the Young's modulus was measured by three different techniques: 1) nanoindentation, 2) three-point bending tests and 3) vibrational resonance with a grindosonic device. The fracture and deformation micromechanics have been also carefully analyzed for each testing condition. The comparison between the studied materials has been performed in order to understand the influence of the main sintering methods and the microstructural characteristics of the single grains on the macroscopic mechanical behavior. The electromechanical behavior of commercial YBCO coated conductors was studied. The mechanical behavior of the tapes was studied under tensile and fatigue tests at 77 and 300 K. The complete strain field on the surface of the sample was obtained by applying Digital Image Correlation (DIC) at 300 K. Addionally, in situ fragmentation tests inside a Scanning Electron Microscope (SEM) were carried out in order to study the fragmentation of the superconducting layer and determine the interfacial shear strength between substrate and ceramic layer. The fragmentation process upon loading of the YBCO layer has been observed and finally, Finite Element Simulations were employed to reproduce delamination and fragmentation phenomena. Finally, joints between the stabilizing Cu sides of two coated conductors have been prepared. The electrical resistivity of the joints was measured for the purpose of qualifying the soldering material and evaluating the soldering process. Additionally, mechanical characterization under single lap shear tests at 300 and 77 K has been carried out. The effect of the applied magnetic field has been studied by applying external magnetic field up to 1 T perpendicular and parallel to the tape-joint at service temperature (77 K). Finally, finite element simulations were employed to study the distribution of the stresses in earch layer, taking into account the three mechanically relevant layers of the coated conductor (Cu-Hastelloy-Cu) that affect its mechanical behavior

Plataforma de simulación en Matlab-Simulink de un accionamiento regulado para emular aerogeneradores

En este proyecto se desarrolla un modelo de simulación de un accionamiento controlado que emula el comportamiento de una turbina eólica, el cual se ha llevado a cabo a través del programa para simulación Matlab/Simulink. Su desarrollo se ha estructurado de la siguiente forma: Tras una breve introducción a la energía eólica y a las máquinas eléctricas objeto de estudio en este proyecto, se procede a la caracterización y representación de dichas maquinas dentro de la plataforma de simulación virtual Simulink. Posteriormente se explican posibles estrategias de control de la máquina de inducción, las cuales son aplicadas para la realización de un control de velocidad. Asimismo, se realiza un control vectorial de par de la máquina de inducción de modo que permita un seguimiento efectivo del par de referencia demandado por el usuario, ante distintas condiciones. Finalmente, se añade el modelo de turbina eólica de manera que, definiendo los valores de velocidad de viento, ángulo de paso y velocidad del eje, permite evaluar el par mecánico desarrollado por la turbina. Este modelo se valida comprobando su funcionamiento para diferentes puntos de operación ante diversas condiciones del par de carga. Las condiciones de carga se establecen acoplando al modelo de la turbina, un generador síncrono de imanes permanentes conectado a una carga resistiva. ! II! ABSTRACT In this project, the simulation model of a controlled drive that emulates the behaviour of a wind turbine is developed. It has been carried out through the platform for multidomian simulation called Matlab/Simulink. Its development has been structured as follows: After a brief introduction to the wind energy and the electrical machines studied in this project, these machines are characterized and represented into the virtual simulation platform, Simulink. Subsequently, the possible control strategies for the induction machine are explained and applied in order to carry out a speed control. Additionally, a torque vector control of the induction machine is performed, so as to enable an effective monitoring of the reference torque requested by the user, under different conditions. Finally, the wind turbine model is implemented so as to assess the turbine mechanical torque, after defining the wind speed, the pitch angle and the shaft speed values. This model is validated by testing its functionality for different operating points under various load torques. The load conditions are set up by attaching a permanent magnets synchronous machine, with a resistive load, to the turbine model.

Desarrollo de un sistema de control por DSP para regular generadores sincronos de imanes permanentes

En el siguiente proyecto se va a llevar a cabo la simulación en la plataforma Matlb Simulink de una maquina síncrona de imanes permanentes (MSIP) en su funcionamiento como generador, emulando un aerogenerador con tecnología SGFC. El generador tendrá como variable de consigna la velocidad de giro del eje y se ajustara el sistema de control para que sea capaz de seguir la señal de consigna ante cambios bruscos del par. Posteriormente se va a detallar y construir todos los elementos que se consideren necesarios para, en proyectos futuros, llevar a la práctica en una maquina real este sistema de control ABSTRACT The object of this Project is to carry a simulation in Matlab Simulink of a synchronous permanent magnets machine (MSIP) in its operation as a generator, emulating a wind turbine technology SGFC. The variable setpoint will be the rotational speed of the shaft, the control system will fit so that it is capable of following the setpoint signal before sudden changes of the pair. Afterward the elements considered necessary for to put into practice this control system in a real machine will be detailed.